linux/drivers/usb/core/config.c

1099 lines
32 KiB

USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: use usb_endpoint_maxp() instead of le16_to_cpu() Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size instead of le16_to_cpu(desc->wMaxPacketSize). This patch fix it up Cc: Armin Fuerst <fuerst@in.tum.de> Cc: Pavel Machek <pavel@ucw.cz> Cc: Johannes Erdfelt <johannes@erdfelt.com> Cc: Vojtech Pavlik <vojtech@suse.cz> Cc: Oliver Neukum <oliver@neukum.name> Cc: David Kubicek <dave@awk.cz> Cc: Johan Hovold <jhovold@gmail.com> Cc: Brad Hards <bhards@bigpond.net.au> Acked-by: Felipe Balbi <balbi@ti.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: David Brownell <david-b@pacbell.net> Cc: David Lopo <dlopo@chipidea.mips.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Xie Xiaobo <X.Xie@freescale.com> Cc: Li Yang <leoli@freescale.com> Cc: Jiang Bo <tanya.jiang@freescale.com> Cc: Yuan-hsin Chen <yhchen@faraday-tech.com> Cc: Darius Augulis <augulis.darius@gmail.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Ben Dooks <ben@simtec.co.uk> Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Herbert Pötzl <herbert@13thfloor.at> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Roman Weissgaerber <weissg@vienna.at> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: Florian Floe Echtler <echtler@fs.tum.de> Cc: Christian Lucht <lucht@codemercs.com> Cc: Juergen Stuber <starblue@sourceforge.net> Cc: Georges Toth <g.toth@e-biz.lu> Cc: Bill Ryder <bryder@sgi.com> Cc: Kuba Ober <kuba@mareimbrium.org> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-23 03:12:03 -07:00
USB: use usb_endpoint_maxp() instead of le16_to_cpu() Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size instead of le16_to_cpu(desc->wMaxPacketSize). This patch fix it up Cc: Armin Fuerst <fuerst@in.tum.de> Cc: Pavel Machek <pavel@ucw.cz> Cc: Johannes Erdfelt <johannes@erdfelt.com> Cc: Vojtech Pavlik <vojtech@suse.cz> Cc: Oliver Neukum <oliver@neukum.name> Cc: David Kubicek <dave@awk.cz> Cc: Johan Hovold <jhovold@gmail.com> Cc: Brad Hards <bhards@bigpond.net.au> Acked-by: Felipe Balbi <balbi@ti.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: David Brownell <david-b@pacbell.net> Cc: David Lopo <dlopo@chipidea.mips.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Xie Xiaobo <X.Xie@freescale.com> Cc: Li Yang <leoli@freescale.com> Cc: Jiang Bo <tanya.jiang@freescale.com> Cc: Yuan-hsin Chen <yhchen@faraday-tech.com> Cc: Darius Augulis <augulis.darius@gmail.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Ben Dooks <ben@simtec.co.uk> Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Herbert Pötzl <herbert@13thfloor.at> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Roman Weissgaerber <weissg@vienna.at> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: Florian Floe Echtler <echtler@fs.tum.de> Cc: Christian Lucht <lucht@codemercs.com> Cc: Juergen Stuber <starblue@sourceforge.net> Cc: Georges Toth <g.toth@e-biz.lu> Cc: Bill Ryder <bryder@sgi.com> Cc: Kuba Ober <kuba@mareimbrium.org> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-23 03:12:03 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: core: Fix duplicate endpoint bug by clearing reserved bits in the descriptor Syzbot has identified a bug in usbcore (see the Closes: tag below) caused by our assumption that the reserved bits in an endpoint descriptor's bEndpointAddress field will always be 0. As a result of the bug, the endpoint_is_duplicate() routine in config.c (and possibly other routines as well) may believe that two descriptors are for distinct endpoints, even though they have the same direction and endpoint number. This can lead to confusion, including the bug identified by syzbot (two descriptors with matching endpoint numbers and directions, where one was interrupt and the other was bulk). To fix the bug, we will clear the reserved bits in bEndpointAddress when we parse the descriptor. (Note that both the USB-2.0 and USB-3.1 specs say these bits are "Reserved, reset to zero".) This requires us to make a copy of the descriptor earlier in usb_parse_endpoint() and use the copy instead of the original when checking for duplicates. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/ Fixes: 0a8fd1346254 ("USB: fix problems with duplicate endpoint addresses") CC: Oliver Neukum <oneukum@suse.com> CC: stable@vger.kernel.org Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-06-27 15:56:18 -04:00
USB: fix problems with duplicate endpoint addresses When checking a new device's descriptors, the USB core does not check for duplicate endpoint addresses. This can cause a problem when the sysfs files for those endpoints are created; trying to create multiple files with the same name will provoke a WARNING: WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0 sysfs: cannot create duplicate filename '/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05' Kernel panic - not syncing: panic_on_warn set ... CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: usb_hub_wq hub_event ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179 [<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542 [<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565 [<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30 [<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59 [< inline >] create_dir lib/kobject.c:71 [<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229 [< inline >] kobject_add_varg lib/kobject.c:366 [<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411 [<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088 [<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206 [<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195 [<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030 [<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937 [<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172 [<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263 This patch prevents the problem by checking for duplicate endpoint addresses during enumeration and skipping any duplicates. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-19 12:03:41 -05:00
USB: fix problems with duplicate endpoint addresses When checking a new device's descriptors, the USB core does not check for duplicate endpoint addresses. This can cause a problem when the sysfs files for those endpoints are created; trying to create multiple files with the same name will provoke a WARNING: WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0 sysfs: cannot create duplicate filename '/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05' Kernel panic - not syncing: panic_on_warn set ... CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: usb_hub_wq hub_event ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179 [<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542 [<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565 [<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30 [<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59 [< inline >] create_dir lib/kobject.c:71 [<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229 [< inline >] kobject_add_varg lib/kobject.c:366 [<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411 [<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088 [<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206 [<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195 [<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030 [<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937 [<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172 [<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263 This patch prevents the problem by checking for duplicate endpoint addresses during enumeration and skipping any duplicates. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-19 12:03:41 -05:00
USB: core: Fix duplicate endpoint bug by clearing reserved bits in the descriptor Syzbot has identified a bug in usbcore (see the Closes: tag below) caused by our assumption that the reserved bits in an endpoint descriptor's bEndpointAddress field will always be 0. As a result of the bug, the endpoint_is_duplicate() routine in config.c (and possibly other routines as well) may believe that two descriptors are for distinct endpoints, even though they have the same direction and endpoint number. This can lead to confusion, including the bug identified by syzbot (two descriptors with matching endpoint numbers and directions, where one was interrupt and the other was bulk). To fix the bug, we will clear the reserved bits in bEndpointAddress when we parse the descriptor. (Note that both the USB-2.0 and USB-3.1 specs say these bits are "Reserved, reset to zero".) This requires us to make a copy of the descriptor earlier in usb_parse_endpoint() and use the copy instead of the original when checking for duplicates. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/ Fixes: 0a8fd1346254 ("USB: fix problems with duplicate endpoint addresses") CC: Oliver Neukum <oneukum@suse.com> CC: stable@vger.kernel.org Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-06-27 15:56:18 -04:00
USB: use usb_endpoint_maxp() instead of le16_to_cpu() Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size instead of le16_to_cpu(desc->wMaxPacketSize). This patch fix it up Cc: Armin Fuerst <fuerst@in.tum.de> Cc: Pavel Machek <pavel@ucw.cz> Cc: Johannes Erdfelt <johannes@erdfelt.com> Cc: Vojtech Pavlik <vojtech@suse.cz> Cc: Oliver Neukum <oliver@neukum.name> Cc: David Kubicek <dave@awk.cz> Cc: Johan Hovold <jhovold@gmail.com> Cc: Brad Hards <bhards@bigpond.net.au> Acked-by: Felipe Balbi <balbi@ti.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: David Brownell <david-b@pacbell.net> Cc: David Lopo <dlopo@chipidea.mips.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Xie Xiaobo <X.Xie@freescale.com> Cc: Li Yang <leoli@freescale.com> Cc: Jiang Bo <tanya.jiang@freescale.com> Cc: Yuan-hsin Chen <yhchen@faraday-tech.com> Cc: Darius Augulis <augulis.darius@gmail.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Ben Dooks <ben@simtec.co.uk> Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Herbert Pötzl <herbert@13thfloor.at> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Roman Weissgaerber <weissg@vienna.at> Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: Florian Floe Echtler <echtler@fs.tum.de> Cc: Christian Lucht <lucht@codemercs.com> Cc: Juergen Stuber <starblue@sourceforge.net> Cc: Georges Toth <g.toth@e-biz.lu> Cc: Bill Ryder <bryder@sgi.com> Cc: Kuba Ober <kuba@mareimbrium.org> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-23 03:12:03 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: Parse and store the SuperSpeed endpoint companion descriptors. The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used to extend the bus protocol to allow more packets to be sent to an endpoint per "microframe". The word microframe was removed from the USB 3.0 specification because the host controller does not send Start Of Frame (SOF) symbols down the USB 3.0 wires. The descriptor defines a bMaxBurst field, which indicates the number of packets of wMaxPacketSize that a SuperSpeed device can send or recieve in a service interval. All non-control endpoints may set this value as high as 16 packets (bMaxBurst = 15). The descriptor also allows isochronous endpoints to further specify that they can send and receive multiple bursts per service interval. The bmAttributes allows them to specify a "Mult" of up to 3 (bmAttributes = 2). Bulk endpoints use bmAttributes to report the number of "Streams" they support. This was an extension of the endpoint pipe concept to allow multiple mass storage device commands to be outstanding for one bulk endpoint at a time. This should allow USB 3.0 mass storage devices to support SCSI command queueing. Bulk endpoints can say they support up to 2^16 (65,536) streams. The information in the endpoint companion descriptor must be stored with the other device, config, interface, and endpoint descriptors because the host controller needs to access them quickly, and we need to install some default values if a SuperSpeed device doesn't provide an endpoint companion descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-27 19:58:14 -07:00
USB: usbcore: Fix slab-out-of-bounds bug during device reset The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04 11:56:27 -04:00
USB: usbcore: Fix slab-out-of-bounds bug during device reset The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04 11:56:27 -04:00
USB: usbcore: Fix slab-out-of-bounds bug during device reset The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04 11:56:27 -04:00
USB: usbcore: Fix slab-out-of-bounds bug during device reset The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04 11:56:27 -04:00
USB: usbcore: Fix slab-out-of-bounds bug during device reset The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04 11:56:27 -04:00
USB: usbcore: Fix slab-out-of-bounds bug during device reset The syzbot fuzzer provoked a slab-out-of-bounds error in the USB core: BUG: KASAN: slab-out-of-bounds in memcmp+0xa6/0xb0 lib/string.c:904 Read of size 1 at addr ffff8881d175bed6 by task kworker/0:3/2746 CPU: 0 PID: 2746 Comm: kworker/0:3 Not tainted 5.3.0-rc5+ #28 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 memcmp+0xa6/0xb0 lib/string.c:904 memcmp include/linux/string.h:400 [inline] descriptors_changed drivers/usb/core/hub.c:5579 [inline] usb_reset_and_verify_device+0x564/0x1300 drivers/usb/core/hub.c:5729 usb_reset_device+0x4c1/0x920 drivers/usb/core/hub.c:5898 rt2x00usb_probe+0x53/0x7af drivers/net/wireless/ralink/rt2x00/rt2x00usb.c:806 The error occurs when the descriptors_changed() routine (called during a device reset) attempts to compare the old and new BOS and capability descriptors. The length it uses for the comparison is the wTotalLength value stored in BOS descriptor, but this value is not necessarily the same as the length actually allocated for the descriptors. If it is larger the routine will call memcmp() with a length that is too big, thus reading beyond the end of the allocated region and leading to this fault. The kernel reads the BOS descriptor twice: first to get the total length of all the capability descriptors, and second to read it along with all those other descriptors. A malicious (or very faulty) device may send different values for the BOS descriptor fields each time. The memory area will be allocated using the wTotalLength value read the first time, but stored within it will be the value read the second time. To prevent this possibility from causing any errors, this patch modifies the BOS descriptor after it has been read the second time: It sets the wTotalLength field to the actual length of the descriptors that were read in and validated. Then the memcpy() call, or any other code using these descriptors, will be able to rely on wTotalLength being valid. Reported-and-tested-by: syzbot+35f4d916c623118d576e@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909041154260.1722-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04 11:56:27 -04:00