linux/net/dsa/Kconfig

224 lines
7.8 KiB

dsa: simplify Kconfig symbols and dependencies 1. Remove CONFIG_HAVE_NET_DSA. CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers should have selected CONFIG_NET_DSA manually. Currently, all drivers has explicit 'depends on NET_DSA', so this is no more needed. 2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones. - dropped !S390 dependency which was introduced to be sure NET_DSA can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years ago and the PHY library itself doesn't depend on !S390 since commit 870a2b5e4fcd ("phylib: remove !S390 dependeny from Kconfig"); - INET dependency is kept to be sure we can select NET_SWITCHDEV; - NETDEVICES dependency is kept to be sure we can select PHYLINK. 3. DSA drivers menu now depends on NET_DSA. Instead on 'depends on NET_DSA' on every single driver, the entire menu now depends on it. This eliminates a lot of duplicated lines from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can be only m or n). This also has a nice side effect that there's no more empty menu on configurations without DSA. 4. Kbuild will now descend into 'drivers/net/dsa' only when CONFIG_NET_DSA is y or m. This is safe since no objects inside this folder can be built without DSA core, as well as when CONFIG_NET_DSA=m, no objects can be built-in. Signed-off-by: Alexander Lobakin <alobakin@pm.me> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-19 15:46:30 +00:00
net: dsa: add GRO support via gro_cells gro_cells lib is used by different encapsulating netdevices, such as geneve, macsec, vxlan etc. to speed up decapsulated traffic processing. CPU tag is a sort of "encapsulation", and we can use the same mechs to greatly improve overall DSA performance. skbs are passed to the GRO layer after removing CPU tags, so we don't need any new packet offload types as it was firstly proposed by me in the first GRO-over-DSA variant [1]. The size of struct gro_cells is sizeof(void *), so hot struct dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields remain in one 32-byte cacheline. The other positive side effect is that drivers for network devices that can be shipped as CPU ports of DSA-driven switches can now use napi_gro_frags() to pass skbs to kernel. Packets built that way are completely non-linear and are likely being dropped without GRO. This was tested on to-be-mainlined-soon Ethernet driver that uses napi_gro_frags(), and the overall performance was on par with the variant from [1], sometimes even better due to minimal overhead. net.core.gro_normal_batch tuning may help to push it to the limit on particular setups and platforms. iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup on 1.2 GHz MIPS board: 5.7-rc2 baseline: [ID] Interval Transfer Bitrate Retr [ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender [ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver Iface RX packets TX packets eth0 7097731 7097702 port0 426050 6671829 port1 6671681 425862 port1.218 6671677 425851 With this patch: [ID] Interval Transfer Bitrate Retr [ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender [ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver Iface RX packets TX packets eth0 9474792 9474777 port0 455200 353288 port1 9019592 455035 port1.218 353144 455024 v2: - Add some performance examples in the commit message; - No functional changes. [1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/ Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21 16:41:08 +03:00
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
dsa: simplify Kconfig symbols and dependencies 1. Remove CONFIG_HAVE_NET_DSA. CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers should have selected CONFIG_NET_DSA manually. Currently, all drivers has explicit 'depends on NET_DSA', so this is no more needed. 2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones. - dropped !S390 dependency which was introduced to be sure NET_DSA can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years ago and the PHY library itself doesn't depend on !S390 since commit 870a2b5e4fcd ("phylib: remove !S390 dependeny from Kconfig"); - INET dependency is kept to be sure we can select NET_SWITCHDEV; - NETDEVICES dependency is kept to be sure we can select PHYLINK. 3. DSA drivers menu now depends on NET_DSA. Instead on 'depends on NET_DSA' on every single driver, the entire menu now depends on it. This eliminates a lot of duplicated lines from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can be only m or n). This also has a nice side effect that there's no more empty menu on configurations without DSA. 4. Kbuild will now descend into 'drivers/net/dsa' only when CONFIG_NET_DSA is y or m. This is safe since no objects inside this folder can be built without DSA core, as well as when CONFIG_NET_DSA=m, no objects can be built-in. Signed-off-by: Alexander Lobakin <alobakin@pm.me> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-19 15:46:30 +00:00
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
net: dsa: add NETC switch tag support The NXP NETC switch tag is a proprietary header added to frames after the source MAC address. The switch tag has 3 types, and each type has 1 ~ 4 subtypes, the details are as follows. Forward NXP switch tag (Type=0): Represents forwarded frames. - SubType = 0 - Normal frame processing. To_Port NXP switch tag (Type=1): Represents frames that are to be sent to a specific switch port. - SubType = 0. No request to perform timestamping. - SubType = 1. Request to perform one-step timestamping. - SubType = 2. Request to perform two-step timestamping. - SubType = 3. Request to perform both one-step timestamping and two-step timestamping. To_Host NXP switch tag (Type=2): Represents frames redirected or copied to the switch management port. - SubType = 0. Received frames redirected or copied to the switch management port. - SubType = 1. Received frames redirected or copied to the switch management port with captured timestamp at the switch port where the frame was received. - SubType = 2. Transmit timestamp response (two-step timestamping). In addition, the length of different type switch tag is different, the minimum length is 6 bytes, the maximum length is 14 bytes. Currently, Forward tag, SubType 0 of To_Port tag and Subtype 0 of To_Host tag are supported. More tags will be supported in the future. Signed-off-by: Wei Fang <wei.fang@nxp.com> Link: https://patch.msgid.link/20260518082506.1318236-10-wei.fang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2026-05-18 16:25:00 +08:00