kernel/linux
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-11-13 07:31:07 +00:00
Code Issues Releases Packages Activity
linux/drivers/memory/atmel-ebi.c

638 lines
15 KiB
Raw Normal View History

memory: atmel-ebi: switch to SPDX license identifiers Adopt the SPDX license identifiers to ease license compliance management. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20190906151519.19442-1-tudor.ambarus@microchip.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-09-06 15:15:28 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: use scoped device node handling to simplify error paths Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-1-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:25 +02:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: make it explicitly non-modular The Kconfig currently controlling compilation of this code is: drivers/memory/Kconfig:config ATMEL_EBI drivers/memory/Kconfig: bool "Atmel EBI driver" ...meaning that it currently is not being built as a module by anyone. Lets remove the few remaining modular references, so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-06-16 20:37:48 -04:00
memory: Use device_get_match_data() Use preferred device_get_match_data() instead of of_match_device() to get the driver match data. With this, adjust the includes to explicitly include the correct headers. Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20231006224402.442078-1-robh@kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-10-06 17:44:01 -05:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: add sam9x60 EBI support The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:55 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: move NUM_CS definition inside EBI driver The total number of EBI CS lines is described by the EBI controller and not by the Matrix. Move the definition for the number of CS inside EBI driver. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20190906150632.19039-1-tudor.ambarus@microchip.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-09-06 15:06:41 +00:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Annotate struct atmel_ebi_dev with __counted_by Prepare for the coming implementation by GCC and Clang of the __counted_by attribute. Flexible array members annotated with __counted_by can have their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family functions). As found with Coccinelle[1], add __counted_by for struct atmel_ebi_dev. [1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20230922175215.work.122-kees@kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-09-22 10:52:15 -07:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: atmel-ebi: Enable the SMC clock if specified Newer versions of the SMC block requires the SMC clock to be enabled before the SMC logic can be used. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:24:09 +01:00
mfd: syscon: atmel-smc: Add helper to retrieve register layout For HSMC controller, the register layout depends on the device i.e. the offset of setup, pulse, cycle, mode and timings registers is not the same. An helper is added to provide the correct register layout. Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease SMC regs manipulation") Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-07-18 15:22:19 +02:00
memory: atmel-ebi: Enable the SMC clock if specified Newer versions of the SMC block requires the SMC clock to be enabled before the SMC logic can be used. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:24:09 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: atmel-ebi: Fix smc cycle xlate converter The converter function for translating ns timings in register values was initialized with a wrong function pointer. This resulted in wrong register values also for the setup and pulse registers when configuring the EBI interface trough dts. Includes a small fix in a comment of the smc driver, which was probably just a copy'n'paste mistake. Signed-off-by: Alexander Dahl <ada@thorsis.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-07-25 14:00:24 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
mfd: syscon: atmel-smc: Add helper to retrieve register layout For HSMC controller, the register layout depends on the device i.e. the offset of setup, pulse, cycle, mode and timings registers is not the same. An helper is added to provide the correct register layout. Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease SMC regs manipulation") Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-07-18 15:22:19 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: atmel-ebi: Allow t_DF timings of zero ns As reported in [1] and in [2] it's not possible to set the device tree property 'atmel,smc-tdf-ns' to zero, although the SoC allows a setting of 0ns for the t_DF time. Allow this setting by doing the same thing as in the atmel nand controller driver by setting ncycles to ATMEL_SMC_MODE_TDF_MIN if zero is set in the dts. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490966.html [2] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-July/520652.html Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexander Dahl <ada@thorsis.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-07-25 14:00:23 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: atmel-ebi: Allow t_DF timings of zero ns As reported in [1] and in [2] it's not possible to set the device tree property 'atmel,smc-tdf-ns' to zero, although the SoC allows a setting of 0ns for the t_DF time. Allow this setting by doing the same thing as in the atmel nand controller driver by setting ncycles to ATMEL_SMC_MODE_TDF_MIN if zero is set in the dts. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490966.html [2] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-July/520652.html Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexander Dahl <ada@thorsis.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-07-25 14:00:23 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: Convert to using %pOF instead of full_name Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Roger Quadros <rogerq@ti.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-07-18 16:43:14 -05:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: Fix smc timing return value evaluation Setting optional EBI/SMC properties through device tree always fails due to wrong evaluation of the return value of atmel_ebi_xslate_smc_timings(). If you put some of those properties in your dts file, but not 'atmel,smc-tdf-ns' the local variable 'required' in atmel_ebi_xslate_smc_timings() stays on 'false' after the first 'if' block. This leads to setting 'ret' to -EINVAL in the first run of the following 'for' loop which is then the return value of this function. However if you set 'atmel,smc-tdf-ns' in the dts file and everything in atmel_ebi_xslate_smc_timings() works well, it returns the content of 'required' which is 'true' then. So the function atmel_ebi_xslate_smc_timings() always returns non-zero which lets its call in atmel_ebi_xslate_smc_config() always fail and thus returning -EINVAL, so the EBI configuration for this node fails. Judging from the following code evaluating the local 'required' variable in atmel_ebi_xslate_smc_config() and the call of caps->xlate_config in atmel_ebi_dev_setup() it's probably right to only let the call fail if a negative error code is returned. Signed-off-by: Alexander Dahl <ada@thorsis.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-07-25 14:00:22 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: Convert to using %pOF instead of full_name Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Roger Quadros <rogerq@ti.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-07-18 16:43:14 -05:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
mfd: syscon: atmel-smc: Add helper to retrieve register layout For HSMC controller, the register layout depends on the device i.e. the offset of setup, pulse, cycle, mode and timings registers is not the same. An helper is added to provide the correct register layout. Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease SMC regs manipulation") Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-07-18 15:22:19 +02:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: atmel-ebi: move NUM_CS definition inside EBI driver The total number of EBI CS lines is described by the EBI controller and not by the Matrix. Move the definition for the number of CS inside EBI driver. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20190906150632.19039-1-tudor.ambarus@microchip.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-09-06 15:06:41 +00:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: Convert to using %pOF instead of full_name Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Roger Quadros <rogerq@ti.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-07-18 16:43:14 -05:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: Convert to using %pOF instead of full_name Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Roger Quadros <rogerq@ti.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-07-18 16:43:14 -05:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Use struct_size() in devm_kzalloc() One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; void *entry[]; }; instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL); This issue was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-23 20:07:06 -05:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Add missing ->numcs assignment ebid->numcs is never assigned, set it to numcs after allocating the EBI dev object. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:33 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: atmel-ebi: move NUM_CS definition inside EBI driver The total number of EBI CS lines is described by the EBI controller and not by the Matrix. Move the definition for the number of CS inside EBI driver. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/20190906150632.19039-1-tudor.ambarus@microchip.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-09-06 15:06:41 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: Properly handle multiple reference to the same CS Some devices are defining several sub-ranges within the same CS iomem range. In this case, we should not duplicate the EBI device config. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:10:37 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: Simplify SMC config code New helpers/macros have been to atmel-smc.h introduced to simplify SMC regs manipulation. Rework the code to use those helpers, and simplify the ->xlate_config(), ->get_config() and ->apply_config() implementations. SMC configs are now stored in a struct atmel_smc_cs_conf object that directly contains registers values, which should help implementing ->suspend()/->resume() hooks. We can also get rid of those regmap fields (and the associated ->init() hook) which are not longer needed thanks to the atmel_[h]smc_cs_conf_{apply,get}() helpers. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:29 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: add sam9x60 EBI support The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:55 +00:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: add sam9x60 EBI support The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:55 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: fix return value check in at91_ebi_dev_disable() Fix the retrn value check which testing the wrong variable in at91_ebi_dev_disable(). Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-09-16 13:03:47 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: simplify with scoped for each OF child loop Use scoped for_each_available_child_of_node_scoped() when iterating over device nodes to make code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-2-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:26 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Add PM ops Add a ->resume() hook to make sure the EBI dev configs are correctly restored when resuming the platform. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:34 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: Use device_get_match_data() Use preferred device_get_match_data() instead of of_match_device() to get the driver match data. With this, adjust the includes to explicitly include the correct headers. Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20231006224402.442078-1-robh@kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-10-06 17:44:01 -05:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: use scoped device node handling to simplify error paths Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-1-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:25 +02:00
memory: atmel-ebi: Enable the SMC clock if specified Newer versions of the SMC block requires the SMC clock to be enabled before the SMC logic can be used. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:24:09 +01:00
memory: atmel-ebi: use scoped device node handling to simplify error paths Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-1-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:25 +02:00
memory: atmel-ebi: Enable the SMC clock if specified Newer versions of the SMC block requires the SMC clock to be enabled before the SMC logic can be used. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:24:09 +01:00
mfd: syscon: atmel-smc: Add helper to retrieve register layout For HSMC controller, the register layout depends on the device i.e. the offset of setup, pulse, cycle, mode and timings registers is not the same. An helper is added to provide the correct register layout. Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease SMC regs manipulation") Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-07-18 15:22:19 +02:00
memory: atmel-ebi: use scoped device node handling to simplify error paths Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-1-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:25 +02:00
mfd: syscon: atmel-smc: Add helper to retrieve register layout For HSMC controller, the register layout depends on the device i.e. the offset of setup, pulse, cycle, mode and timings registers is not the same. An helper is added to provide the correct register layout. Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease SMC regs manipulation") Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-07-18 15:22:19 +02:00
memory: atmel-ebi: Enable the SMC clock if specified Newer versions of the SMC block requires the SMC clock to be enabled before the SMC logic can be used. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:24:09 +01:00
memory: atmel-ebi: use scoped device node handling to simplify error paths Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-1-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:25 +02:00
memory: atmel-ebi: Enable the SMC clock if specified Newer versions of the SMC block requires the SMC clock to be enabled before the SMC logic can be used. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-27 10:24:09 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Stop using reg_field objects for simple things Turn the ->ebi_csa reg field into a simple offset that can be used with with the matrix regmap. Using reg fields was overkill for this use case. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:30 +01:00
memory: atmel-ebi: add generic name for ebi regmap The sam9x60 board defines the CCFG_EBICSA register under SFR, and not as a MATRIX register, as previous boards do. Add a more generic name for the EBI regmap as a prerequisite for sam9x60 ebi support. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-02-13 08:59:48 +00:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: simplify with scoped for each OF child loop Use scoped for_each_available_child_of_node_scoped() when iterating over device nodes to make code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-2-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:26 +02:00
memory: atmel-ebi: Use of_property_present() for testing DT property presence It is preferred to use typed property access functions (i.e. of_property_read_<type> functions) rather than low-level of_get_property/of_find_property functions for reading properties. As part of this, convert of_get_property/of_find_property calls to the recently added of_property_present() helper when we just want to test for presence of a property and nothing more. Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230310144711.1543295-1-robh@kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-03-10 08:47:11 -06:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: Convert to using %pOF instead of full_name Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Roger Quadros <rogerq@ti.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Tony Lindgren <tony@atomide.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-07-18 16:43:14 -05:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: simplify with scoped for each OF child loop Use scoped for_each_available_child_of_node_scoped() when iterating over device nodes to make code a bit simpler. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240816-cleanup-h-of-node-put-memory-v2-2-9eed0ee16b78@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2024-08-16 12:54:26 +02:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: mark PM ops as __maybe_unused We get a harmless warning without CONFIG_PM: drivers/memory/atmel-ebi.c:584:12: error: 'atmel_ebi_resume' defined but not used [-Werror=unused-function] Marking the function as __maybe_unused does the right thing here and drops it silently when unused. Fixes: a483fb10e5ea ("memory: atmel-ebi: Add PM ops") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-04-19 19:48:07 +02:00
memory: atmel-ebi: Add PM ops Add a ->resume() hook to make sure the EBI dev configs are correctly restored when resuming the platform. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:34 +01:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: Allow deferred probing After removing of_platform_default_populate() calls the atmel-ebi driver was affected by deferred probing. platform_driver_probe() is incompatible with deferred probing. This led to atmel-ebi driver eventually not being probed on at91 sam9x60-curiosity and other sam9x60 based boards. Subsequently the nand-controller driver (nand-controller being a child node of ebi) on that platform was not probed and thus raw NAND flash was inaccessible, preventing devices to boot with rootfs on raw NAND flash (e.g. with UBI/UBIFS). Fixes: 0b0f7e6539a7 ("ARM: at91: remove unnecessary of_platform_default_populate calls") Cc: stable@vger.kernel.org Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Alexander Dahl <ada@thorsis.com> Link: https://patch.msgid.link/20260429125930.844790-1-ada@thorsis.com Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2026-04-29 14:59:30 +02:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Change naming scheme The EBI block is not only available on at91 SoCs, but also on avr32 ones. Change the structure and function prefixes from at91_ebi to atmel_ebi to match this fact and make the prefix and driver name consistent. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:32 +01:00
memory: atmel-ebi: Add PM ops Add a ->resume() hook to make sure the EBI dev configs are correctly restored when resuming the platform. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-03-16 09:30:34 +01:00
memory: add Atmel EBI (External Bus Interface) driver The EBI (External Bus Interface) is used to access external peripherals (NOR, SRAM, NAND, and other specific devices like ethernet controllers). Each device is assigned a CS line and an address range and can have its own configuration (timings, access mode, bus width, ...). This driver provides a generic DT binding to configure a device according to its requirements. For specific device controllers (like the NAND one) the SMC timings should be configured by the controller driver through the matrix and smc syscon regmaps. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-23 09:44:54 +02:00
memory: atmel-ebi: Allow deferred probing After removing of_platform_default_populate() calls the atmel-ebi driver was affected by deferred probing. platform_driver_probe() is incompatible with deferred probing. This led to atmel-ebi driver eventually not being probed on at91 sam9x60-curiosity and other sam9x60 based boards. Subsequently the nand-controller driver (nand-controller being a child node of ebi) on that platform was not probed and thus raw NAND flash was inaccessible, preventing devices to boot with rootfs on raw NAND flash (e.g. with UBI/UBIFS). Fixes: 0b0f7e6539a7 ("ARM: at91: remove unnecessary of_platform_default_populate calls") Cc: stable@vger.kernel.org Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Alexander Dahl <ada@thorsis.com> Link: https://patch.msgid.link/20260429125930.844790-1-ada@thorsis.com Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2026-04-29 14:59:30 +02:00