linux/drivers/w1/w1.c

1271 lines
32 KiB

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157 Based on 3 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [graeme] [gregory] [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema] [hk] [hemahk]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1105 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-27 08:55:06 +02:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: feature, enable hardware strong pullup Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by: David Fries <david@fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-15 22:04:42 -07:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
W1: split master mutex to avoid deadlocks. The 'mutex' in struct w1_master is use for two very different purposes. Firstly it protects various data structures such as the list of all slaves. Secondly it protects the w1 buss against concurrent accesses. This can lead to deadlocks when the ->probe code called while adding a slave needs to talk on the bus, as is the case for power_supply devices. ds2780 and ds2781 drivers contain a work around to track which process hold the lock simply to avoid this deadlock. bq27000 doesn't have that work around and so deadlocks. There are other possible deadlocks involving sysfs. When removing a device the sysfs s_active lock is held, so the lock that protects the slave list must take precedence over s_active. However when access power_supply attributes via sysfs, the s_active lock must take precedence over the lock that protects accesses to the bus. So to avoid deadlocks between w1 slaves and sysfs, these must be two separate locks. Making them separate means that the work around in ds2780 and ds2781 can be removed. So this patch: - adds a new mutex: "bus_mutex" which serialises access to the bus. - takes in mutex in w1_search and ds1wm_search while they access the bus for searching. The mutex is dropped before calling the callback which adds the slave. - changes all slaves to use bus_mutex instead of mutex to protect access to the bus - removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the related code from drivers/power/ds278[01]_battery.c which calls them. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-18 15:59:52 +10:00
2022-12-05 16:04:34 +08:00