This website requires JavaScript.
About
Status
₊˚⊹Discord
Explore
Register
Sign in
Reference in a new issue
Blame
Copy permalink
Reference in a new issue
Copy permalink
kernel
/
linux
Star
0
Fork
You've already forked linux
0
mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/
synced
2026-11-15 19:56:03 +00:00
Code
Issues
Releases
Packages
Activity
31d2b61ba2
linux
/
include
/
media
/
cec-pin.h
79 lines
2.8 KiB
Raw
Normal View
History
media: include/(uapi/)media: add SPDX license info Replace the old license information with the corresponding SPDX license for those headers that I authored. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2018-02-07 09:05:46 -05:00
media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-07-11 03:30:42 -03:00
media: cec-gpio: handle gpiod_get_value errors correctly gpiod_get_value() can return negative values if an error occurs. In several places this error code was ignored. Ensure that errors codes are handled correctly throughout the CEC pin framework and CEC pin drivers. The return code of the cec_pin_ops read() callback had to be changed from 'bool' to 'int', which mean the prototype of that callback in the sun4i drm driver also had to be changed. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-04-21 11:23:41 +02:00
media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-07-11 03:30:42 -03:00
media: cec-gpio: handle gpiod_get_value errors correctly gpiod_get_value() can return negative values if an error occurs. In several places this error code was ignored. Ensure that errors codes are handled correctly throughout the CEC pin framework and CEC pin drivers. The return code of the cec_pin_ops read() callback had to be changed from 'bool' to 'int', which mean the prototype of that callback in the sun4i drm driver also had to be changed. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-04-21 11:23:41 +02:00
media: cec-pin: add 'received' callback Drivers that use the CEC pin framework have no way of processing messages themselves by providing the 'received' callback. This is present in cec_ops, but not in cec_pin_ops. Add support for this callback. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-10-09 11:49:19 -03:00
media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-07-11 03:30:42 -03:00
media: cec-gpio: handle gpiod_get_value errors correctly gpiod_get_value() can return negative values if an error occurs. In several places this error code was ignored. Ensure that errors codes are handled correctly throughout the CEC pin framework and CEC pin drivers. The return code of the cec_pin_ops read() callback had to be changed from 'bool' to 'int', which mean the prototype of that callback in the sun4i drm driver also had to be changed. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-04-21 11:23:41 +02:00
media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-07-11 03:30:42 -03:00
media: cec: add CEC_EVENT_PIN_HPD_LOW/HIGH events Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH. This is specifically meant for use with the upcoming cec-gpio driver and makes it possible to trace when the HPD pin changes. Some HDMI sinks do strange things with the HPD and this makes it easy to debug this. Note that this also moves the initialization of a devnode mutex and list to the allocate_adapter function: if the HPD is high, then as soon as the HPD interrupt is created an interrupt occurs and cec_queue_pin_hpd_event() is called which requires that the devnode mutex and list are initialized. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-08-15 10:07:25 -04:00
media: cec: add support for 5V signal testing Add support for the new 5V CEC events Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2018-06-28 07:43:46 -04:00
media: cec-pin: add 'received' callback Drivers that use the CEC pin framework have no way of processing messages themselves by providing the 'received' callback. This is present in cec_ops, but not in cec_pin_ops. Add support for this callback. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-10-09 11:49:19 -03:00
media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2017-07-11 03:30:42 -03:00