linux/arch/powerpc/include/asm/kvm_ppc.h

1118 lines
38 KiB

KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Book3S: Allow XICS emulation to work in nested hosts using XIVE Currently, the KVM code assumes that if the host kernel is using the XIVE interrupt controller (the new interrupt controller that first appeared in POWER9 systems), then the in-kernel XICS emulation will use the XIVE hardware to deliver interrupts to the guest. However, this only works when the host is running in hypervisor mode and has full access to all of the XIVE functionality. It doesn't work in any nested virtualization scenario, either with PR KVM or nested-HV KVM, because the XICS-on-XIVE code calls directly into the native-XIVE routines, which are not initialized and cannot function correctly because they use OPAL calls, and OPAL is not available in a guest. This means that using the in-kernel XICS emulation in a nested hypervisor that is using XIVE as its interrupt controller will cause a (nested) host kernel crash. To fix this, we change most of the places where the current code calls xive_enabled() to select between the XICS-on-XIVE emulation and the plain XICS emulation to call a new function, xics_on_xive(), which returns false in a guest. However, there is a further twist. The plain XICS emulation has some functions which are used in real mode and access the underlying XICS controller (the interrupt controller of the host) directly. In the case of a nested hypervisor, this means doing XICS hypercalls directly. When the nested host is using XIVE as its interrupt controller, these hypercalls will fail. Therefore this also adds checks in the places where the XICS emulation wants to access the underlying interrupt controller directly, and if that is XIVE, makes the code use the virtual mode fallback paths, which call generic kernel infrastructure rather than doing direct XICS access. Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2019-02-04 22:07:20 +11:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Fetch prefixed instructions from the guest In order to handle emulation of prefixed instructions in the guest, this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64 bits on 64-bit platforms. For prefixed instructions, the upper 32 bits are used for the prefix and the lower 32 bits for the suffix, and both halves are byte-swapped if the guest endianness differs from the host. Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR register on POWER10. Like HEIR, for a prefixed instruction it is defined to have the prefix is in the top 32 bits and the suffix in the bottom 32 bits, with both halves in the correct byte order. kvmppc_get_last_inst is extended on 64-bit machines to put the prefix and suffix in the right places in the ppc_inst_t being returned. kvmppc_load_last_inst now returns the instruction in an unsigned long in the same format as vcpu->arch.last_inst. It makes the decision about whether to fetch a suffix based on the SRR1_PREFIXED bit in the MSR image stored in the vcpu struct, which generally comes from SRR1 or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to be set if the interrupt occurred due to a prefixed instruction and cleared otherwise for all interrupts except for instruction storage interrupt, which does not come to the hypervisor. It is set to zero for asynchronous interrupts such as external interrupts. In previous ISA versions it was always set to 0 for all interrupts except instruction storage interrupt. The code in book3s_hv_rmhandlers.S that loads the faulting instruction on a HDSI is only used on POWER8 and therefore doesn't ever need to load a suffix. [npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the type of instruction that was fetched.] Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Tested-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo
2023-03-08 17:35:23 +11:00
KVM: PPC: Book3S HV P9: Stop handling hcalls in real-mode in the P9 path In the interest of minimising the amount of code that is run in "real-mode", don't handle hcalls in real mode in the P9 path. This requires some new handlers for H_CEDE and xics-on-xive to be added before xive is pulled or cede logic is checked. This introduces a change in radix guest behaviour where radix guests that execute 'sc 1' in userspace now get a privilege fault whereas previously the 'sc 1' would be reflected as a syscall interrupt to the guest kernel. That reflection is only required for hash guests that run PR KVM. Background: In POWER8 and earlier processors, it is very expensive to exit from the HV real mode context of a guest hypervisor interrupt, and switch to host virtual mode. On those processors, guest->HV interrupts reach the hypervisor with the MMU off because the MMU is loaded with guest context (LPCR, SDR1, SLB), and the other threads in the sub-core need to be pulled out of the guest too. Then the primary must save off guest state, invalidate SLB and ERAT, and load up host state before the MMU can be enabled to run in host virtual mode (~= regular Linux mode). Hash guests also require a lot of hcalls to run due to the nature of the MMU architecture and paravirtualisation design. The XICS interrupt controller requires hcalls to run. So KVM traditionally tries hard to avoid the full exit, by handling hcalls and other interrupts in real mode as much as possible. By contrast, POWER9 has independent MMU context per-thread, and in radix mode the hypervisor is in host virtual memory mode when the HV interrupt is taken. Radix guests do not require significant hcalls to manage their translations, and xive guests don't need hcalls to handle interrupts. So it's much less important for performance to handle hcalls in real mode on POWER9. One caveat is that the TCE hcalls are performance critical, real-mode variants introduced for POWER8 in order to achieve 10GbE performance. Real mode TCE hcalls were found to be less important on POWER9, which was able to drive 40GBe networking without them (using the virt mode hcalls) but performance is still important. These hcalls will benefit from subsequent guest entry/exit optimisation including possibly a faster "partial exit" that does not entirely switch to host context to handle the hcall. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210528090752.3542186-14-npiggin@gmail.com
2021-05-28 19:07:33 +10:00
KVM: PPC: Only get pages when actually needed, not in prepare_memory_region() This removes the code from kvmppc_core_prepare_memory_region() that looked up the VMA for the region being added and called hva_to_page to get the pfns for the memory. We have no guarantee that there will be anything mapped there at the time of the KVM_SET_USER_MEMORY_REGION ioctl call; userspace can do that ioctl and then map memory into the region later. Instead we defer looking up the pfn for each memory page until it is needed, which generally means when the guest does an H_ENTER hcall on the page. Since we can't call get_user_pages in real mode, if we don't already have the pfn for the page, kvmppc_h_enter() will return H_TOO_HARD and we then call kvmppc_virtmode_h_enter() once we get back to kernel context. That calls kvmppc_get_guest_page() to get the pfn for the page, and then calls back to kvmppc_h_enter() to redo the HPTE insertion. When the first vcpu starts executing, we need to have the RMO or VRMA region mapped so that the guest's real mode accesses will work. Thus we now have a check in kvmppc_vcpu_run() to see if the RMO/VRMA is set up and if not, call kvmppc_hv_setup_rma(). It checks if the memslot starting at guest physical 0 now has RMO memory mapped there; if so it sets it up for the guest, otherwise on POWER7 it sets up the VRMA. The function that does that, kvmppc_map_vrma, is now a bit simpler, as it calls kvmppc_virtmode_h_enter instead of creating the HPTE itself. Since we are now potentially updating entries in the slot_phys[] arrays from multiple vcpu threads, we now have a spinlock protecting those updates to ensure that we don't lose track of any references to pages. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Avi Kivity <avi@redhat.com>
2011-12-12 12:31:00 +00:00
KVM: PPC: Handle some PAPR hcalls in the kernel This adds the infrastructure for handling PAPR hcalls in the kernel, either early in the guest exit path while we are still in real mode, or later once the MMU has been turned back on and we are in the full kernel context. The advantage of handling hcalls in real mode if possible is that we avoid two partition switches -- and this will become more important when we support SMT4 guests, since a partition switch means we have to pull all of the threads in the core out of the guest. The disadvantage is that we can only access the kernel linear mapping, not anything vmalloced or ioremapped, since the MMU is off. This also adds code to handle the following hcalls in real mode: H_ENTER Add an HPTE to the hashed page table H_REMOVE Remove an HPTE from the hashed page table H_READ Read HPTEs from the hashed page table H_PROTECT Change the protection bits in an HPTE H_BULK_REMOVE Remove up to 4 HPTEs from the hashed page table H_SET_DABR Set the data address breakpoint register Plus code to handle the following hcalls in the kernel: H_CEDE Idle the vcpu until an interrupt or H_PROD hcall arrives H_PROD Wake up a ceded vcpu H_REGISTER_VPA Register a virtual processor area (VPA) The code that runs in real mode has to be in the base kernel, not in the module, if KVM is compiled as a module. The real-mode code can only access the kernel linear mapping, not vmalloc or ioremap space. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:22:05 +00:00
KVM: PPC: VFIO: Add in-kernel acceleration for VFIO This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO without passing them to user space which saves time on switching to user space and back. This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM. KVM tries to handle a TCE request in the real mode, if failed it passes the request to the virtual mode to complete the operation. If it a virtual mode handler fails, the request is passed to the user space; this is not expected to happen though. To avoid dealing with page use counters (which is tricky in real mode), this only accelerates SPAPR TCE IOMMU v2 clients which are required to pre-register the userspace memory. The very first TCE request will be handled in the VFIO SPAPR TCE driver anyway as the userspace view of the TCE table (iommu_table::it_userspace) is not allocated till the very first mapping happens and we cannot call vmalloc in real mode. If we fail to update a hardware IOMMU table unexpected reason, we just clear it and move on as there is nothing really we can do about it - for example, if we hot plug a VFIO device to a guest, existing TCE tables will be mirrored automatically to the hardware and there is no interface to report to the guest about possible failures. This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd and associates a physical IOMMU table with the SPAPR TCE table (which is a guest view of the hardware IOMMU table). The iommu_table object is cached and referenced so we do not have to look up for it in real mode. This does not implement the UNSET counterpart as there is no use for it - once the acceleration is enabled, the existing userspace won't disable it unless a VFIO container is destroyed; this adds necessary cleanup to the KVM_DEV_VFIO_GROUP_DEL handler. This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user space. This adds real mode version of WARN_ON_ONCE() as the generic version causes problems with rcu_sched. Since we testing what vmalloc_to_phys() returns in the code, this also adds a check for already existing vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect(). This finally makes use of vfio_external_user_iommu_id() which was introduced quite some time ago and was considered for removal. Tests show that this patch increases transmission speed from 220MB/s to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card). Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Acked-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2017-03-22 15:21:56 +11:00
KVM: PPC: Book3S HV: Fix migration and HPT resizing of HPT guests on radix hosts This fixes two errors that prevent a guest using the HPT MMU from successfully migrating to a POWER9 host in radix MMU mode, or resizing its HPT when running on a radix host. The first bug was that commit 8dc6cca556e4 ("KVM: PPC: Book3S HV: Don't rely on host's page size information", 2017-09-11) missed two uses of hpte_base_page_size(), one in the HPT rehashing code and one in kvm_htab_write() (which is used on the destination side in migrating a HPT guest). Instead we use kvmppc_hpte_base_page_shift(). Having the shift count means that we can use left and right shifts instead of multiplication and division in a few places. Along the way, this adds a check in kvm_htab_write() to ensure that the page size encoding in the incoming HPTEs is recognized, and if not return an EINVAL error to userspace. The second bug was that kvm_htab_write was performing some but not all of the functions of kvmhv_setup_mmu(), resulting in the destination VM being left in radix mode as far as the hardware is concerned. The simplest fix for now is make kvm_htab_write() call kvmppc_setup_partition_table() like kvmppc_hv_setup_htab_rma() does. In future it would be better to refactor the code more extensively to remove the duplication. Fixes: 8dc6cca556e4 ("KVM: PPC: Book3S HV: Don't rely on host's page size information") Fixes: 7a84084c6054 ("KVM: PPC: Book3S HV: Set partition table rather than SDR1 on POWER9") Reported-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2017-11-22 14:38:53 +11:00
KVM: PPC: Book3S HV: Provide a method for userspace to read and write the HPT A new ioctl, KVM_PPC_GET_HTAB_FD, returns a file descriptor. Reads on this fd return the contents of the HPT (hashed page table), writes create and/or remove entries in the HPT. There is a new capability, KVM_CAP_PPC_HTAB_FD, to indicate the presence of the ioctl. The ioctl takes an argument structure with the index of the first HPT entry to read out and a set of flags. The flags indicate whether the user is intending to read or write the HPT, and whether to return all entries or only the "bolted" entries (those with the bolted bit, 0x10, set in the first doubleword). This is intended for use in implementing qemu's savevm/loadvm and for live migration. Therefore, on reads, the first pass returns information about all HPTEs (or all bolted HPTEs). When the first pass reaches the end of the HPT, it returns from the read. Subsequent reads only return information about HPTEs that have changed since they were last read. A read that finds no changed HPTEs in the HPT following where the last read finished will return 0 bytes. The format of the data provides a simple run-length compression of the invalid entries. Each block of data starts with a header that indicates the index (position in the HPT, which is just an array), the number of valid entries starting at that index (may be zero), and the number of invalid entries following those valid entries. The valid entries, 16 bytes each, follow the header. The invalid entries are not explicitly represented. Signed-off-by: Paul Mackerras <paulus@samba.org> [agraf: fix documentation] Signed-off-by: Alexander Graf <agraf@suse.de>
2012-11-19 22:57:20 +00:00
KVM: PPC: Book3S HV: Provide a method for userspace to read and write the HPT A new ioctl, KVM_PPC_GET_HTAB_FD, returns a file descriptor. Reads on this fd return the contents of the HPT (hashed page table), writes create and/or remove entries in the HPT. There is a new capability, KVM_CAP_PPC_HTAB_FD, to indicate the presence of the ioctl. The ioctl takes an argument structure with the index of the first HPT entry to read out and a set of flags. The flags indicate whether the user is intending to read or write the HPT, and whether to return all entries or only the "bolted" entries (those with the bolted bit, 0x10, set in the first doubleword). This is intended for use in implementing qemu's savevm/loadvm and for live migration. Therefore, on reads, the first pass returns information about all HPTEs (or all bolted HPTEs). When the first pass reaches the end of the HPT, it returns from the read. Subsequent reads only return information about HPTEs that have changed since they were last read. A read that finds no changed HPTEs in the HPT following where the last read finished will return 0 bytes. The format of the data provides a simple run-length compression of the invalid entries. Each block of data starts with a header that indicates the index (position in the HPT, which is just an array), the number of valid entries starting at that index (may be zero), and the number of invalid entries following those valid entries. The valid entries, 16 bytes each, follow the header. The invalid entries are not explicitly represented. Signed-off-by: Paul Mackerras <paulus@samba.org> [agraf: fix documentation] Signed-off-by: Alexander Graf <agraf@suse.de>
2012-11-19 22:57:20 +00:00
KVM: PPC: Merge powerpc's debugfs entry content into generic entry At the moment KVM on PPC creates 4 types of entries under the kvm debugfs: 1) "%pid-%fd" per a KVM instance (for all platforms); 2) "vm%pid" (for PPC Book3s HV KVM); 3) "vm%u_vcpu%u_timing" (for PPC Book3e KVM); 4) "kvm-xive-%p" (for XIVE PPC Book3s KVM, the same for XICS); The problem with this is that multiple VMs per process is not allowed for 2) and 3) which makes it possible for userspace to trigger errors when creating duplicated debugfs entries. This merges all these into 1). This defines kvm_arch_create_kvm_debugfs() similar to kvm_arch_create_vcpu_debugfs(). This defines 2 hooks in kvmppc_ops that allow specific KVM implementations add necessary entries, this adds the _e500 suffix to kvmppc_create_vcpu_debugfs_e500() to make it clear what platform it is for. This makes use of already existing kvm_arch_create_vcpu_debugfs() on PPC. This removes no more used debugfs_dir pointers from PPC kvm_arch structs. This stops removing vcpu entries as once created vcpus stay around for the entire life of a VM and removed when the KVM instance is closed, see commit d56f5136b010 ("KVM: let kvm_destroy_vm_debugfs clean up vCPU debugfs directories"). Suggested-by: Fabiano Rosas <farosas@linux.ibm.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220111005404.162219-1-aik@ozlabs.ru
2022-01-11 11:54:04 +11:00
KVM: PPC: Fetch prefixed instructions from the guest In order to handle emulation of prefixed instructions in the guest, this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64 bits on 64-bit platforms. For prefixed instructions, the upper 32 bits are used for the prefix and the lower 32 bits for the suffix, and both halves are byte-swapped if the guest endianness differs from the host. Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR register on POWER10. Like HEIR, for a prefixed instruction it is defined to have the prefix is in the top 32 bits and the suffix in the bottom 32 bits, with both halves in the correct byte order. kvmppc_get_last_inst is extended on 64-bit machines to put the prefix and suffix in the right places in the ppc_inst_t being returned. kvmppc_load_last_inst now returns the instruction in an unsigned long in the same format as vcpu->arch.last_inst. It makes the decision about whether to fetch a suffix based on the SRR1_PREFIXED bit in the MSR image stored in the vcpu struct, which generally comes from SRR1 or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to be set if the interrupt occurred due to a prefixed instruction and cleared otherwise for all interrupts except for instruction storage interrupt, which does not come to the hypervisor. It is set to zero for asynchronous interrupts such as external interrupts. In previous ISA versions it was always set to 0 for all interrupts except instruction storage interrupt. The code in book3s_hv_rmhandlers.S that loads the faulting instruction on a HDSI is only used on POWER8 and therefore doesn't ever need to load a suffix. [npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the type of instruction that was fetched.] Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Tested-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo
2023-03-08 17:35:23 +11:00
KVM: PPC: Fetch prefixed instructions from the guest In order to handle emulation of prefixed instructions in the guest, this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64 bits on 64-bit platforms. For prefixed instructions, the upper 32 bits are used for the prefix and the lower 32 bits for the suffix, and both halves are byte-swapped if the guest endianness differs from the host. Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR register on POWER10. Like HEIR, for a prefixed instruction it is defined to have the prefix is in the top 32 bits and the suffix in the bottom 32 bits, with both halves in the correct byte order. kvmppc_get_last_inst is extended on 64-bit machines to put the prefix and suffix in the right places in the ppc_inst_t being returned. kvmppc_load_last_inst now returns the instruction in an unsigned long in the same format as vcpu->arch.last_inst. It makes the decision about whether to fetch a suffix based on the SRR1_PREFIXED bit in the MSR image stored in the vcpu struct, which generally comes from SRR1 or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to be set if the interrupt occurred due to a prefixed instruction and cleared otherwise for all interrupts except for instruction storage interrupt, which does not come to the hypervisor. It is set to zero for asynchronous interrupts such as external interrupts. In previous ISA versions it was always set to 0 for all interrupts except instruction storage interrupt. The code in book3s_hv_rmhandlers.S that loads the faulting instruction on a HDSI is only used on POWER8 and therefore doesn't ever need to load a suffix. [npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the type of instruction that was fetched.] Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Tested-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo
2023-03-08 17:35:23 +11:00
KVM: PPC: Fetch prefixed instructions from the guest In order to handle emulation of prefixed instructions in the guest, this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64 bits on 64-bit platforms. For prefixed instructions, the upper 32 bits are used for the prefix and the lower 32 bits for the suffix, and both halves are byte-swapped if the guest endianness differs from the host. Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR register on POWER10. Like HEIR, for a prefixed instruction it is defined to have the prefix is in the top 32 bits and the suffix in the bottom 32 bits, with both halves in the correct byte order. kvmppc_get_last_inst is extended on 64-bit machines to put the prefix and suffix in the right places in the ppc_inst_t being returned. kvmppc_load_last_inst now returns the instruction in an unsigned long in the same format as vcpu->arch.last_inst. It makes the decision about whether to fetch a suffix based on the SRR1_PREFIXED bit in the MSR image stored in the vcpu struct, which generally comes from SRR1 or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to be set if the interrupt occurred due to a prefixed instruction and cleared otherwise for all interrupts except for instruction storage interrupt, which does not come to the hypervisor. It is set to zero for asynchronous interrupts such as external interrupts. In previous ISA versions it was always set to 0 for all interrupts except instruction storage interrupt. The code in book3s_hv_rmhandlers.S that loads the faulting instruction on a HDSI is only used on POWER8 and therefore doesn't ever need to load a suffix. [npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the type of instruction that was fetched.] Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Tested-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo
2023-03-08 17:35:23 +11:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests This adds infrastructure which will be needed to allow book3s_hv KVM to run on older POWER processors, including PPC970, which don't support the Virtual Real Mode Area (VRMA) facility, but only the Real Mode Offset (RMO) facility. These processors require a physically contiguous, aligned area of memory for each guest. When the guest does an access in real mode (MMU off), the address is compared against a limit value, and if it is lower, the address is ORed with an offset value (from the Real Mode Offset Register (RMOR)) and the result becomes the real address for the access. The size of the RMA has to be one of a set of supported values, which usually includes 64MB, 128MB, 256MB and some larger powers of 2. Since we are unlikely to be able to allocate 64MB or more of physically contiguous memory after the kernel has been running for a while, we allocate a pool of RMAs at boot time using the bootmem allocator. The size and number of the RMAs can be set using the kvm_rma_size=xx and kvm_rma_count=xx kernel command line options. KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability of the pool of preallocated RMAs. The capability value is 1 if the processor can use an RMA but doesn't require one (because it supports the VRMA facility), or 2 if the processor requires an RMA for each guest. This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the pool and returns a file descriptor which can be used to map the RMA. It also returns the size of the RMA in the argument structure. Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION ioctl calls from userspace. To cope with this, we now preallocate the kvm->arch.ram_pginfo array when the VM is created with a size sufficient for up to 64GB of guest memory. Subsequently we will get rid of this array and use memory associated with each memslot instead. This moves most of the code that translates the user addresses into host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level to kvmppc_core_prepare_memory_region. Also, instead of having to look up the VMA for each page in order to check the page size, we now check that the pages we get are compound pages of 16MB. However, if we are adding memory that is mapped to an RMA, we don't bother with calling get_user_pages_fast and instead just offset from the base pfn for the RMA. Typically the RMA gets added after vcpus are created, which makes it inconvenient to have the LPCR (logical partition control register) value in the vcpu->arch struct, since the LPCR controls whether the processor uses RMA or VRMA for the guest. This moves the LPCR value into the kvm->arch struct and arranges for the MER (mediated external request) bit, which is the only bit that varies between vcpus, to be set in assembly code when going into the guest if there is a pending external interrupt request. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:25:44 +00:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests This adds infrastructure which will be needed to allow book3s_hv KVM to run on older POWER processors, including PPC970, which don't support the Virtual Real Mode Area (VRMA) facility, but only the Real Mode Offset (RMO) facility. These processors require a physically contiguous, aligned area of memory for each guest. When the guest does an access in real mode (MMU off), the address is compared against a limit value, and if it is lower, the address is ORed with an offset value (from the Real Mode Offset Register (RMOR)) and the result becomes the real address for the access. The size of the RMA has to be one of a set of supported values, which usually includes 64MB, 128MB, 256MB and some larger powers of 2. Since we are unlikely to be able to allocate 64MB or more of physically contiguous memory after the kernel has been running for a while, we allocate a pool of RMAs at boot time using the bootmem allocator. The size and number of the RMAs can be set using the kvm_rma_size=xx and kvm_rma_count=xx kernel command line options. KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability of the pool of preallocated RMAs. The capability value is 1 if the processor can use an RMA but doesn't require one (because it supports the VRMA facility), or 2 if the processor requires an RMA for each guest. This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the pool and returns a file descriptor which can be used to map the RMA. It also returns the size of the RMA in the argument structure. Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION ioctl calls from userspace. To cope with this, we now preallocate the kvm->arch.ram_pginfo array when the VM is created with a size sufficient for up to 64GB of guest memory. Subsequently we will get rid of this array and use memory associated with each memslot instead. This moves most of the code that translates the user addresses into host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level to kvmppc_core_prepare_memory_region. Also, instead of having to look up the VMA for each page in order to check the page size, we now check that the pages we get are compound pages of 16MB. However, if we are adding memory that is mapped to an RMA, we don't bother with calling get_user_pages_fast and instead just offset from the base pfn for the RMA. Typically the RMA gets added after vcpus are created, which makes it inconvenient to have the LPCR (logical partition control register) value in the vcpu->arch struct, since the LPCR controls whether the processor uses RMA or VRMA for the guest. This moves the LPCR value into the kvm->arch struct and arranges for the MER (mediated external request) bit, which is the only bit that varies between vcpus, to be set in assembly code when going into the guest if there is a pending external interrupt request. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:25:44 +00:00
KVM: PPC: Book3S HV: use smp_mb() when setting/clearing host_ipi flag On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB of memory running the following guest configs: guest A: - 224GB of memory - 56 VCPUs (sockets=1,cores=28,threads=2), where: VCPUs 0-1 are pinned to CPUs 0-3, VCPUs 2-3 are pinned to CPUs 4-7, ... VCPUs 54-55 are pinned to CPUs 108-111 guest B: - 4GB of memory - 4 VCPUs (sockets=1,cores=4,threads=1) with the following workloads (with KSM and THP enabled in all): guest A: stress --cpu 40 --io 20 --vm 20 --vm-bytes 512M guest B: stress --cpu 4 --io 4 --vm 4 --vm-bytes 512M host: stress --cpu 4 --io 4 --vm 2 --vm-bytes 256M the below soft-lockup traces were observed after an hour or so and persisted until the host was reset (this was found to be reliably reproducible for this configuration, for kernels 4.15, 4.18, 5.0, and 5.3-rc5): [ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU [ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941 [ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709] [ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913] [ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331] [ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338] [ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525] [ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU [ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243 [ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU [ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714 [ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU [ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403 [ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds. [ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds. [ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds. [ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds. [ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds. [ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds. [ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds. [ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds. [ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 CPUs 45, 24, and 124 are stuck on spin locks, likely held by CPUs 105 and 31. CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on target CPU 42. For instance: # CPU 105 registers (via xmon) R00 = c00000000020b20c R16 = 00007d1bcd800000 R01 = c00000363eaa7970 R17 = 0000000000000001 R02 = c0000000019b3a00 R18 = 000000000000006b R03 = 000000000000002a R19 = 00007d537d7aecf0 R04 = 000000000000002a R20 = 60000000000000e0 R05 = 000000000000002a R21 = 0801000000000080 R06 = c0002073fb0caa08 R22 = 0000000000000d60 R07 = c0000000019ddd78 R23 = 0000000000000001 R08 = 000000000000002a R24 = c00000000147a700 R09 = 0000000000000001 R25 = c0002073fb0ca908 R10 = c000008ffeb4e660 R26 = 0000000000000000 R11 = c0002073fb0ca900 R27 = c0000000019e2464 R12 = c000000000050790 R28 = c0000000000812b0 R13 = c000207fff623e00 R29 = c0002073fb0ca808 R14 = 00007d1bbee00000 R30 = c0002073fb0ca800 R15 = 00007d1bcd600000 R31 = 0000000000000800 pc = c00000000020b260 smp_call_function_many+0x3d0/0x460 cfar= c00000000020b270 smp_call_function_many+0x3e0/0x460 lr = c00000000020b20c smp_call_function_many+0x37c/0x460 msr = 900000010288b033 cr = 44024824 ctr = c000000000050790 xer = 0000000000000000 trap = 100 CPU 42 is running normally, doing VCPU work: # CPU 42 stack trace (via xmon) [link register ] c00800001be17188 kvmppc_book3s_radix_page_fault+0x90/0x2b0 [kvm_hv] [c000008ed3343820] c000008ed3343850 (unreliable) [c000008ed33438d0] c00800001be11b6c kvmppc_book3s_hv_page_fault+0x264/0xe30 [kvm_hv] [c000008ed33439d0] c00800001be0d7b4 kvmppc_vcpu_run_hv+0x8dc/0xb50 [kvm_hv] [c000008ed3343ae0] c00800001c10891c kvmppc_vcpu_run+0x34/0x48 [kvm] [c000008ed3343b00] c00800001c10475c kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm] [c000008ed3343b90] c00800001c0f5a78 kvm_vcpu_ioctl+0x470/0x7c8 [kvm] [c000008ed3343d00] c000000000475450 do_vfs_ioctl+0xe0/0xc70 [c000008ed3343db0] c0000000004760e4 ksys_ioctl+0x104/0x120 [c000008ed3343e00] c000000000476128 sys_ioctl+0x28/0x80 [c000008ed3343e20] c00000000000b388 system_call+0x5c/0x70 --- Exception: c00 (System Call) at 00007d545cfd7694 SP (7d53ff7edf50) is in userspace It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION] was set for CPU 42 by at least 1 of the CPUs waiting in smp_call_function_many(), but somehow the corresponding call_single_queue entries were never processed by CPU 42, causing the callers to spin in csd_lock_wait() indefinitely. Nick Piggin suggested something similar to the following sequence as a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE IPI messages seems to be most common, but any mix of CALL_FUNCTION and !CALL_FUNCTION messages could trigger it): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() 105: smp_muxed_ipi_set_message(): 105: smb_mb() // STORE DEFERRED DUE TO RE-ORDERING --105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 42: // returns to executing guest | // RE-ORDERED STORE COMPLETES ->105: message[CALL_FUNCTION] = 1 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue This can be prevented with an smp_mb() at the beginning of kvmppc_set_host_ipi(), such that stores to message[<type>] (or other state indicated by the host_ipi flag) are ordered vs. the store to to host_ipi. However, doing so might still allow for the following scenario (not yet observed): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() // STORE DEFERRED DUE TO RE-ORDERING -- 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 105: smp_muxed_ipi_set_message(): | 105: smb_mb() | 105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | // RE-ORDERED STORE COMPLETES -> 42: kvmppc_set_host_ipi(42, 0) 42: // returns to executing guest 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue Fixing this scenario would require an smp_mb() *after* clearing host_ipi flag in kvmppc_set_host_ipi() to order the store vs. subsequent processing of IPI messages. To handle both cases, this patch splits kvmppc_set_host_ipi() into separate set/clear functions, where we execute smp_mb() prior to setting host_ipi flag, and after clearing host_ipi flag. These functions pair with each other to synchronize the sender and receiver sides. With that change in place the above workload ran for 20 hours without triggering any lock-ups. Fixes: 755563bc79c7 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0 Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com
2019-09-11 17:31:55 -05:00
KVM: PPC: Book3S HV: use smp_mb() when setting/clearing host_ipi flag On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB of memory running the following guest configs: guest A: - 224GB of memory - 56 VCPUs (sockets=1,cores=28,threads=2), where: VCPUs 0-1 are pinned to CPUs 0-3, VCPUs 2-3 are pinned to CPUs 4-7, ... VCPUs 54-55 are pinned to CPUs 108-111 guest B: - 4GB of memory - 4 VCPUs (sockets=1,cores=4,threads=1) with the following workloads (with KSM and THP enabled in all): guest A: stress --cpu 40 --io 20 --vm 20 --vm-bytes 512M guest B: stress --cpu 4 --io 4 --vm 4 --vm-bytes 512M host: stress --cpu 4 --io 4 --vm 2 --vm-bytes 256M the below soft-lockup traces were observed after an hour or so and persisted until the host was reset (this was found to be reliably reproducible for this configuration, for kernels 4.15, 4.18, 5.0, and 5.3-rc5): [ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU [ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941 [ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709] [ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913] [ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331] [ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338] [ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525] [ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU [ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243 [ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU [ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714 [ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU [ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403 [ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds. [ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds. [ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds. [ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds. [ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds. [ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds. [ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds. [ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds. [ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 CPUs 45, 24, and 124 are stuck on spin locks, likely held by CPUs 105 and 31. CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on target CPU 42. For instance: # CPU 105 registers (via xmon) R00 = c00000000020b20c R16 = 00007d1bcd800000 R01 = c00000363eaa7970 R17 = 0000000000000001 R02 = c0000000019b3a00 R18 = 000000000000006b R03 = 000000000000002a R19 = 00007d537d7aecf0 R04 = 000000000000002a R20 = 60000000000000e0 R05 = 000000000000002a R21 = 0801000000000080 R06 = c0002073fb0caa08 R22 = 0000000000000d60 R07 = c0000000019ddd78 R23 = 0000000000000001 R08 = 000000000000002a R24 = c00000000147a700 R09 = 0000000000000001 R25 = c0002073fb0ca908 R10 = c000008ffeb4e660 R26 = 0000000000000000 R11 = c0002073fb0ca900 R27 = c0000000019e2464 R12 = c000000000050790 R28 = c0000000000812b0 R13 = c000207fff623e00 R29 = c0002073fb0ca808 R14 = 00007d1bbee00000 R30 = c0002073fb0ca800 R15 = 00007d1bcd600000 R31 = 0000000000000800 pc = c00000000020b260 smp_call_function_many+0x3d0/0x460 cfar= c00000000020b270 smp_call_function_many+0x3e0/0x460 lr = c00000000020b20c smp_call_function_many+0x37c/0x460 msr = 900000010288b033 cr = 44024824 ctr = c000000000050790 xer = 0000000000000000 trap = 100 CPU 42 is running normally, doing VCPU work: # CPU 42 stack trace (via xmon) [link register ] c00800001be17188 kvmppc_book3s_radix_page_fault+0x90/0x2b0 [kvm_hv] [c000008ed3343820] c000008ed3343850 (unreliable) [c000008ed33438d0] c00800001be11b6c kvmppc_book3s_hv_page_fault+0x264/0xe30 [kvm_hv] [c000008ed33439d0] c00800001be0d7b4 kvmppc_vcpu_run_hv+0x8dc/0xb50 [kvm_hv] [c000008ed3343ae0] c00800001c10891c kvmppc_vcpu_run+0x34/0x48 [kvm] [c000008ed3343b00] c00800001c10475c kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm] [c000008ed3343b90] c00800001c0f5a78 kvm_vcpu_ioctl+0x470/0x7c8 [kvm] [c000008ed3343d00] c000000000475450 do_vfs_ioctl+0xe0/0xc70 [c000008ed3343db0] c0000000004760e4 ksys_ioctl+0x104/0x120 [c000008ed3343e00] c000000000476128 sys_ioctl+0x28/0x80 [c000008ed3343e20] c00000000000b388 system_call+0x5c/0x70 --- Exception: c00 (System Call) at 00007d545cfd7694 SP (7d53ff7edf50) is in userspace It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION] was set for CPU 42 by at least 1 of the CPUs waiting in smp_call_function_many(), but somehow the corresponding call_single_queue entries were never processed by CPU 42, causing the callers to spin in csd_lock_wait() indefinitely. Nick Piggin suggested something similar to the following sequence as a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE IPI messages seems to be most common, but any mix of CALL_FUNCTION and !CALL_FUNCTION messages could trigger it): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() 105: smp_muxed_ipi_set_message(): 105: smb_mb() // STORE DEFERRED DUE TO RE-ORDERING --105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 42: // returns to executing guest | // RE-ORDERED STORE COMPLETES ->105: message[CALL_FUNCTION] = 1 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue This can be prevented with an smp_mb() at the beginning of kvmppc_set_host_ipi(), such that stores to message[<type>] (or other state indicated by the host_ipi flag) are ordered vs. the store to to host_ipi. However, doing so might still allow for the following scenario (not yet observed): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() // STORE DEFERRED DUE TO RE-ORDERING -- 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 105: smp_muxed_ipi_set_message(): | 105: smb_mb() | 105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | // RE-ORDERED STORE COMPLETES -> 42: kvmppc_set_host_ipi(42, 0) 42: // returns to executing guest 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue Fixing this scenario would require an smp_mb() *after* clearing host_ipi flag in kvmppc_set_host_ipi() to order the store vs. subsequent processing of IPI messages. To handle both cases, this patch splits kvmppc_set_host_ipi() into separate set/clear functions, where we execute smp_mb() prior to setting host_ipi flag, and after clearing host_ipi flag. These functions pair with each other to synchronize the sender and receiver sides. With that change in place the above workload ran for 20 hours without triggering any lock-ups. Fixes: 755563bc79c7 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0 Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com
2019-09-11 17:31:55 -05:00
KVM: PPC: Book3S HV: use smp_mb() when setting/clearing host_ipi flag On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB of memory running the following guest configs: guest A: - 224GB of memory - 56 VCPUs (sockets=1,cores=28,threads=2), where: VCPUs 0-1 are pinned to CPUs 0-3, VCPUs 2-3 are pinned to CPUs 4-7, ... VCPUs 54-55 are pinned to CPUs 108-111 guest B: - 4GB of memory - 4 VCPUs (sockets=1,cores=4,threads=1) with the following workloads (with KSM and THP enabled in all): guest A: stress --cpu 40 --io 20 --vm 20 --vm-bytes 512M guest B: stress --cpu 4 --io 4 --vm 4 --vm-bytes 512M host: stress --cpu 4 --io 4 --vm 2 --vm-bytes 256M the below soft-lockup traces were observed after an hour or so and persisted until the host was reset (this was found to be reliably reproducible for this configuration, for kernels 4.15, 4.18, 5.0, and 5.3-rc5): [ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU [ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941 [ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709] [ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913] [ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331] [ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338] [ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525] [ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU [ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243 [ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU [ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714 [ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU [ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403 [ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds. [ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds. [ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds. [ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds. [ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds. [ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds. [ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds. [ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds. [ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 CPUs 45, 24, and 124 are stuck on spin locks, likely held by CPUs 105 and 31. CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on target CPU 42. For instance: # CPU 105 registers (via xmon) R00 = c00000000020b20c R16 = 00007d1bcd800000 R01 = c00000363eaa7970 R17 = 0000000000000001 R02 = c0000000019b3a00 R18 = 000000000000006b R03 = 000000000000002a R19 = 00007d537d7aecf0 R04 = 000000000000002a R20 = 60000000000000e0 R05 = 000000000000002a R21 = 0801000000000080 R06 = c0002073fb0caa08 R22 = 0000000000000d60 R07 = c0000000019ddd78 R23 = 0000000000000001 R08 = 000000000000002a R24 = c00000000147a700 R09 = 0000000000000001 R25 = c0002073fb0ca908 R10 = c000008ffeb4e660 R26 = 0000000000000000 R11 = c0002073fb0ca900 R27 = c0000000019e2464 R12 = c000000000050790 R28 = c0000000000812b0 R13 = c000207fff623e00 R29 = c0002073fb0ca808 R14 = 00007d1bbee00000 R30 = c0002073fb0ca800 R15 = 00007d1bcd600000 R31 = 0000000000000800 pc = c00000000020b260 smp_call_function_many+0x3d0/0x460 cfar= c00000000020b270 smp_call_function_many+0x3e0/0x460 lr = c00000000020b20c smp_call_function_many+0x37c/0x460 msr = 900000010288b033 cr = 44024824 ctr = c000000000050790 xer = 0000000000000000 trap = 100 CPU 42 is running normally, doing VCPU work: # CPU 42 stack trace (via xmon) [link register ] c00800001be17188 kvmppc_book3s_radix_page_fault+0x90/0x2b0 [kvm_hv] [c000008ed3343820] c000008ed3343850 (unreliable) [c000008ed33438d0] c00800001be11b6c kvmppc_book3s_hv_page_fault+0x264/0xe30 [kvm_hv] [c000008ed33439d0] c00800001be0d7b4 kvmppc_vcpu_run_hv+0x8dc/0xb50 [kvm_hv] [c000008ed3343ae0] c00800001c10891c kvmppc_vcpu_run+0x34/0x48 [kvm] [c000008ed3343b00] c00800001c10475c kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm] [c000008ed3343b90] c00800001c0f5a78 kvm_vcpu_ioctl+0x470/0x7c8 [kvm] [c000008ed3343d00] c000000000475450 do_vfs_ioctl+0xe0/0xc70 [c000008ed3343db0] c0000000004760e4 ksys_ioctl+0x104/0x120 [c000008ed3343e00] c000000000476128 sys_ioctl+0x28/0x80 [c000008ed3343e20] c00000000000b388 system_call+0x5c/0x70 --- Exception: c00 (System Call) at 00007d545cfd7694 SP (7d53ff7edf50) is in userspace It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION] was set for CPU 42 by at least 1 of the CPUs waiting in smp_call_function_many(), but somehow the corresponding call_single_queue entries were never processed by CPU 42, causing the callers to spin in csd_lock_wait() indefinitely. Nick Piggin suggested something similar to the following sequence as a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE IPI messages seems to be most common, but any mix of CALL_FUNCTION and !CALL_FUNCTION messages could trigger it): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() 105: smp_muxed_ipi_set_message(): 105: smb_mb() // STORE DEFERRED DUE TO RE-ORDERING --105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 42: // returns to executing guest | // RE-ORDERED STORE COMPLETES ->105: message[CALL_FUNCTION] = 1 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue This can be prevented with an smp_mb() at the beginning of kvmppc_set_host_ipi(), such that stores to message[<type>] (or other state indicated by the host_ipi flag) are ordered vs. the store to to host_ipi. However, doing so might still allow for the following scenario (not yet observed): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() // STORE DEFERRED DUE TO RE-ORDERING -- 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 105: smp_muxed_ipi_set_message(): | 105: smb_mb() | 105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | // RE-ORDERED STORE COMPLETES -> 42: kvmppc_set_host_ipi(42, 0) 42: // returns to executing guest 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue Fixing this scenario would require an smp_mb() *after* clearing host_ipi flag in kvmppc_set_host_ipi() to order the store vs. subsequent processing of IPI messages. To handle both cases, this patch splits kvmppc_set_host_ipi() into separate set/clear functions, where we execute smp_mb() prior to setting host_ipi flag, and after clearing host_ipi flag. These functions pair with each other to synchronize the sender and receiver sides. With that change in place the above workload ran for 20 hours without triggering any lock-ups. Fixes: 755563bc79c7 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0 Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com
2019-09-11 17:31:55 -05:00
KVM: PPC: Book3S HV: use smp_mb() when setting/clearing host_ipi flag On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB of memory running the following guest configs: guest A: - 224GB of memory - 56 VCPUs (sockets=1,cores=28,threads=2), where: VCPUs 0-1 are pinned to CPUs 0-3, VCPUs 2-3 are pinned to CPUs 4-7, ... VCPUs 54-55 are pinned to CPUs 108-111 guest B: - 4GB of memory - 4 VCPUs (sockets=1,cores=4,threads=1) with the following workloads (with KSM and THP enabled in all): guest A: stress --cpu 40 --io 20 --vm 20 --vm-bytes 512M guest B: stress --cpu 4 --io 4 --vm 4 --vm-bytes 512M host: stress --cpu 4 --io 4 --vm 2 --vm-bytes 256M the below soft-lockup traces were observed after an hour or so and persisted until the host was reset (this was found to be reliably reproducible for this configuration, for kernels 4.15, 4.18, 5.0, and 5.3-rc5): [ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU [ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941 [ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709] [ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913] [ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331] [ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338] [ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525] [ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU [ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243 [ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU [ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714 [ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU [ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403 [ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds. [ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds. [ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds. [ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds. [ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds. [ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds. [ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds. [ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds. [ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 CPUs 45, 24, and 124 are stuck on spin locks, likely held by CPUs 105 and 31. CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on target CPU 42. For instance: # CPU 105 registers (via xmon) R00 = c00000000020b20c R16 = 00007d1bcd800000 R01 = c00000363eaa7970 R17 = 0000000000000001 R02 = c0000000019b3a00 R18 = 000000000000006b R03 = 000000000000002a R19 = 00007d537d7aecf0 R04 = 000000000000002a R20 = 60000000000000e0 R05 = 000000000000002a R21 = 0801000000000080 R06 = c0002073fb0caa08 R22 = 0000000000000d60 R07 = c0000000019ddd78 R23 = 0000000000000001 R08 = 000000000000002a R24 = c00000000147a700 R09 = 0000000000000001 R25 = c0002073fb0ca908 R10 = c000008ffeb4e660 R26 = 0000000000000000 R11 = c0002073fb0ca900 R27 = c0000000019e2464 R12 = c000000000050790 R28 = c0000000000812b0 R13 = c000207fff623e00 R29 = c0002073fb0ca808 R14 = 00007d1bbee00000 R30 = c0002073fb0ca800 R15 = 00007d1bcd600000 R31 = 0000000000000800 pc = c00000000020b260 smp_call_function_many+0x3d0/0x460 cfar= c00000000020b270 smp_call_function_many+0x3e0/0x460 lr = c00000000020b20c smp_call_function_many+0x37c/0x460 msr = 900000010288b033 cr = 44024824 ctr = c000000000050790 xer = 0000000000000000 trap = 100 CPU 42 is running normally, doing VCPU work: # CPU 42 stack trace (via xmon) [link register ] c00800001be17188 kvmppc_book3s_radix_page_fault+0x90/0x2b0 [kvm_hv] [c000008ed3343820] c000008ed3343850 (unreliable) [c000008ed33438d0] c00800001be11b6c kvmppc_book3s_hv_page_fault+0x264/0xe30 [kvm_hv] [c000008ed33439d0] c00800001be0d7b4 kvmppc_vcpu_run_hv+0x8dc/0xb50 [kvm_hv] [c000008ed3343ae0] c00800001c10891c kvmppc_vcpu_run+0x34/0x48 [kvm] [c000008ed3343b00] c00800001c10475c kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm] [c000008ed3343b90] c00800001c0f5a78 kvm_vcpu_ioctl+0x470/0x7c8 [kvm] [c000008ed3343d00] c000000000475450 do_vfs_ioctl+0xe0/0xc70 [c000008ed3343db0] c0000000004760e4 ksys_ioctl+0x104/0x120 [c000008ed3343e00] c000000000476128 sys_ioctl+0x28/0x80 [c000008ed3343e20] c00000000000b388 system_call+0x5c/0x70 --- Exception: c00 (System Call) at 00007d545cfd7694 SP (7d53ff7edf50) is in userspace It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION] was set for CPU 42 by at least 1 of the CPUs waiting in smp_call_function_many(), but somehow the corresponding call_single_queue entries were never processed by CPU 42, causing the callers to spin in csd_lock_wait() indefinitely. Nick Piggin suggested something similar to the following sequence as a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE IPI messages seems to be most common, but any mix of CALL_FUNCTION and !CALL_FUNCTION messages could trigger it): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() 105: smp_muxed_ipi_set_message(): 105: smb_mb() // STORE DEFERRED DUE TO RE-ORDERING --105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 42: // returns to executing guest | // RE-ORDERED STORE COMPLETES ->105: message[CALL_FUNCTION] = 1 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue This can be prevented with an smp_mb() at the beginning of kvmppc_set_host_ipi(), such that stores to message[<type>] (or other state indicated by the host_ipi flag) are ordered vs. the store to to host_ipi. However, doing so might still allow for the following scenario (not yet observed): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() // STORE DEFERRED DUE TO RE-ORDERING -- 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 105: smp_muxed_ipi_set_message(): | 105: smb_mb() | 105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | // RE-ORDERED STORE COMPLETES -> 42: kvmppc_set_host_ipi(42, 0) 42: // returns to executing guest 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue Fixing this scenario would require an smp_mb() *after* clearing host_ipi flag in kvmppc_set_host_ipi() to order the store vs. subsequent processing of IPI messages. To handle both cases, this patch splits kvmppc_set_host_ipi() into separate set/clear functions, where we execute smp_mb() prior to setting host_ipi flag, and after clearing host_ipi flag. These functions pair with each other to synchronize the sender and receiver sides. With that change in place the above workload ran for 20 hours without triggering any lock-ups. Fixes: 755563bc79c7 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0 Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com
2019-09-11 17:31:55 -05:00
KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests This adds infrastructure which will be needed to allow book3s_hv KVM to run on older POWER processors, including PPC970, which don't support the Virtual Real Mode Area (VRMA) facility, but only the Real Mode Offset (RMO) facility. These processors require a physically contiguous, aligned area of memory for each guest. When the guest does an access in real mode (MMU off), the address is compared against a limit value, and if it is lower, the address is ORed with an offset value (from the Real Mode Offset Register (RMOR)) and the result becomes the real address for the access. The size of the RMA has to be one of a set of supported values, which usually includes 64MB, 128MB, 256MB and some larger powers of 2. Since we are unlikely to be able to allocate 64MB or more of physically contiguous memory after the kernel has been running for a while, we allocate a pool of RMAs at boot time using the bootmem allocator. The size and number of the RMAs can be set using the kvm_rma_size=xx and kvm_rma_count=xx kernel command line options. KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability of the pool of preallocated RMAs. The capability value is 1 if the processor can use an RMA but doesn't require one (because it supports the VRMA facility), or 2 if the processor requires an RMA for each guest. This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the pool and returns a file descriptor which can be used to map the RMA. It also returns the size of the RMA in the argument structure. Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION ioctl calls from userspace. To cope with this, we now preallocate the kvm->arch.ram_pginfo array when the VM is created with a size sufficient for up to 64GB of guest memory. Subsequently we will get rid of this array and use memory associated with each memslot instead. This moves most of the code that translates the user addresses into host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level to kvmppc_core_prepare_memory_region. Also, instead of having to look up the VMA for each page in order to check the page size, we now check that the pages we get are compound pages of 16MB. However, if we are adding memory that is mapped to an RMA, we don't bother with calling get_user_pages_fast and instead just offset from the base pfn for the RMA. Typically the RMA gets added after vcpus are created, which makes it inconvenient to have the LPCR (logical partition control register) value in the vcpu->arch struct, since the LPCR controls whether the processor uses RMA or VRMA for the guest. This moves the LPCR value into the kvm->arch struct and arranges for the MER (mediated external request) bit, which is the only bit that varies between vcpus, to be set in assembly code when going into the guest if there is a pending external interrupt request. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:25:44 +00:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests This adds infrastructure which will be needed to allow book3s_hv KVM to run on older POWER processors, including PPC970, which don't support the Virtual Real Mode Area (VRMA) facility, but only the Real Mode Offset (RMO) facility. These processors require a physically contiguous, aligned area of memory for each guest. When the guest does an access in real mode (MMU off), the address is compared against a limit value, and if it is lower, the address is ORed with an offset value (from the Real Mode Offset Register (RMOR)) and the result becomes the real address for the access. The size of the RMA has to be one of a set of supported values, which usually includes 64MB, 128MB, 256MB and some larger powers of 2. Since we are unlikely to be able to allocate 64MB or more of physically contiguous memory after the kernel has been running for a while, we allocate a pool of RMAs at boot time using the bootmem allocator. The size and number of the RMAs can be set using the kvm_rma_size=xx and kvm_rma_count=xx kernel command line options. KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability of the pool of preallocated RMAs. The capability value is 1 if the processor can use an RMA but doesn't require one (because it supports the VRMA facility), or 2 if the processor requires an RMA for each guest. This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the pool and returns a file descriptor which can be used to map the RMA. It also returns the size of the RMA in the argument structure. Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION ioctl calls from userspace. To cope with this, we now preallocate the kvm->arch.ram_pginfo array when the VM is created with a size sufficient for up to 64GB of guest memory. Subsequently we will get rid of this array and use memory associated with each memslot instead. This moves most of the code that translates the user addresses into host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level to kvmppc_core_prepare_memory_region. Also, instead of having to look up the VMA for each page in order to check the page size, we now check that the pages we get are compound pages of 16MB. However, if we are adding memory that is mapped to an RMA, we don't bother with calling get_user_pages_fast and instead just offset from the base pfn for the RMA. Typically the RMA gets added after vcpus are created, which makes it inconvenient to have the LPCR (logical partition control register) value in the vcpu->arch struct, since the LPCR controls whether the processor uses RMA or VRMA for the guest. This moves the LPCR value into the kvm->arch struct and arranges for the MER (mediated external request) bit, which is the only bit that varies between vcpus, to be set in assembly code when going into the guest if there is a pending external interrupt request. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:25:44 +00:00
KVM: PPC: Book3S HV: use smp_mb() when setting/clearing host_ipi flag On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB of memory running the following guest configs: guest A: - 224GB of memory - 56 VCPUs (sockets=1,cores=28,threads=2), where: VCPUs 0-1 are pinned to CPUs 0-3, VCPUs 2-3 are pinned to CPUs 4-7, ... VCPUs 54-55 are pinned to CPUs 108-111 guest B: - 4GB of memory - 4 VCPUs (sockets=1,cores=4,threads=1) with the following workloads (with KSM and THP enabled in all): guest A: stress --cpu 40 --io 20 --vm 20 --vm-bytes 512M guest B: stress --cpu 4 --io 4 --vm 4 --vm-bytes 512M host: stress --cpu 4 --io 4 --vm 2 --vm-bytes 256M the below soft-lockup traces were observed after an hour or so and persisted until the host was reset (this was found to be reliably reproducible for this configuration, for kernels 4.15, 4.18, 5.0, and 5.3-rc5): [ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU [ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941 [ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709] [ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913] [ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331] [ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338] [ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525] [ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU [ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243 [ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU [ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714 [ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791] [ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU [ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403 [ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds. [ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds. [ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds. [ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds. [ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds. [ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds. [ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds. [ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 [ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds. [ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1 CPUs 45, 24, and 124 are stuck on spin locks, likely held by CPUs 105 and 31. CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on target CPU 42. For instance: # CPU 105 registers (via xmon) R00 = c00000000020b20c R16 = 00007d1bcd800000 R01 = c00000363eaa7970 R17 = 0000000000000001 R02 = c0000000019b3a00 R18 = 000000000000006b R03 = 000000000000002a R19 = 00007d537d7aecf0 R04 = 000000000000002a R20 = 60000000000000e0 R05 = 000000000000002a R21 = 0801000000000080 R06 = c0002073fb0caa08 R22 = 0000000000000d60 R07 = c0000000019ddd78 R23 = 0000000000000001 R08 = 000000000000002a R24 = c00000000147a700 R09 = 0000000000000001 R25 = c0002073fb0ca908 R10 = c000008ffeb4e660 R26 = 0000000000000000 R11 = c0002073fb0ca900 R27 = c0000000019e2464 R12 = c000000000050790 R28 = c0000000000812b0 R13 = c000207fff623e00 R29 = c0002073fb0ca808 R14 = 00007d1bbee00000 R30 = c0002073fb0ca800 R15 = 00007d1bcd600000 R31 = 0000000000000800 pc = c00000000020b260 smp_call_function_many+0x3d0/0x460 cfar= c00000000020b270 smp_call_function_many+0x3e0/0x460 lr = c00000000020b20c smp_call_function_many+0x37c/0x460 msr = 900000010288b033 cr = 44024824 ctr = c000000000050790 xer = 0000000000000000 trap = 100 CPU 42 is running normally, doing VCPU work: # CPU 42 stack trace (via xmon) [link register ] c00800001be17188 kvmppc_book3s_radix_page_fault+0x90/0x2b0 [kvm_hv] [c000008ed3343820] c000008ed3343850 (unreliable) [c000008ed33438d0] c00800001be11b6c kvmppc_book3s_hv_page_fault+0x264/0xe30 [kvm_hv] [c000008ed33439d0] c00800001be0d7b4 kvmppc_vcpu_run_hv+0x8dc/0xb50 [kvm_hv] [c000008ed3343ae0] c00800001c10891c kvmppc_vcpu_run+0x34/0x48 [kvm] [c000008ed3343b00] c00800001c10475c kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm] [c000008ed3343b90] c00800001c0f5a78 kvm_vcpu_ioctl+0x470/0x7c8 [kvm] [c000008ed3343d00] c000000000475450 do_vfs_ioctl+0xe0/0xc70 [c000008ed3343db0] c0000000004760e4 ksys_ioctl+0x104/0x120 [c000008ed3343e00] c000000000476128 sys_ioctl+0x28/0x80 [c000008ed3343e20] c00000000000b388 system_call+0x5c/0x70 --- Exception: c00 (System Call) at 00007d545cfd7694 SP (7d53ff7edf50) is in userspace It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION] was set for CPU 42 by at least 1 of the CPUs waiting in smp_call_function_many(), but somehow the corresponding call_single_queue entries were never processed by CPU 42, causing the callers to spin in csd_lock_wait() indefinitely. Nick Piggin suggested something similar to the following sequence as a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE IPI messages seems to be most common, but any mix of CALL_FUNCTION and !CALL_FUNCTION messages could trigger it): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() 105: smp_muxed_ipi_set_message(): 105: smb_mb() // STORE DEFERRED DUE TO RE-ORDERING --105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 42: // returns to executing guest | // RE-ORDERED STORE COMPLETES ->105: message[CALL_FUNCTION] = 1 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue This can be prevented with an smp_mb() at the beginning of kvmppc_set_host_ipi(), such that stores to message[<type>] (or other state indicated by the host_ipi flag) are ordered vs. the store to to host_ipi. However, doing so might still allow for the following scenario (not yet observed): CPU X: smp_muxed_ipi_set_message(): X: smp_mb() X: message[RESCHEDULE] = 1 X: doorbell_global_ipi(42): X: kvmppc_set_host_ipi(42, 1) X: ppc_msgsnd_sync()/smp_mb() X: ppc_msgsnd() -> 42 42: doorbell_exception(): // from CPU X 42: ppc_msgsync() // STORE DEFERRED DUE TO RE-ORDERING -- 42: kvmppc_set_host_ipi(42, 0) | 42: smp_ipi_demux_relaxed() | 105: smp_muxed_ipi_set_message(): | 105: smb_mb() | 105: message[CALL_FUNCTION] = 1 | 105: doorbell_global_ipi(42): | 105: kvmppc_set_host_ipi(42, 1) | // RE-ORDERED STORE COMPLETES -> 42: kvmppc_set_host_ipi(42, 0) 42: // returns to executing guest 105: ppc_msgsnd_sync()/smp_mb() 105: ppc_msgsnd() -> 42 42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored 105: // hangs waiting on 42 to process messages/call_single_queue Fixing this scenario would require an smp_mb() *after* clearing host_ipi flag in kvmppc_set_host_ipi() to order the store vs. subsequent processing of IPI messages. To handle both cases, this patch splits kvmppc_set_host_ipi() into separate set/clear functions, where we execute smp_mb() prior to setting host_ipi flag, and after clearing host_ipi flag. These functions pair with each other to synchronize the sender and receiver sides. With that change in place the above workload ran for 20 hours without triggering any lock-ups. Fixes: 755563bc79c7 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0 Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com
2019-09-11 17:31:55 -05:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Book3S HV: Host-side RM data structures This patch defines the data structures to support the setting up of host side operations while running in real mode in the guest, and also the functions to allocate and free it. The operations are for now limited to virtual XICS operations. Currently, we have only defined one operation in the data structure: - Wake up a VCPU sleeping in the host when it receives a virtual interrupt The operations are assigned at the core level because PowerKVM requires that the host run in SMT off mode. For each core, we will need to manage its state atomically - where the state is defined by: 1. Is the core running in the host? 2. Is there a Real Mode (RM) operation pending on the host? Currently, core state is only managed at the whole-core level even when the system is in split-core mode. This just limits the number of free or "available" cores in the host to perform any host-side operations. The kvmppc_host_rm_core.rm_data allows any data to be passed by KVM in real mode to the host core along with the operation to be performed. The kvmppc_host_rm_ops structure is allocated the very first time a guest VM is started. Initial core state is also set - all online cores are in the host. This structure is never deleted, not even when there are no active guests. However, it needs to be freed when the module is unloaded because the kvmppc_host_rm_ops_hv can contain function pointers to kvm-hv.ko functions for the different supported host operations. Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2015-12-17 14:59:06 -06:00
KVM: PPC: Book3S HV: Complete passthrough interrupt in host In existing real mode ICP code, when updating the virtual ICP state, if there is a required action that cannot be completely handled in real mode, as for instance, a VCPU needs to be woken up, flags are set in the ICP to indicate the required action. This is checked when returning from hypercalls to decide whether the call needs switch back to the host where the action can be performed in virtual mode. Note that if h_ipi_redirect is enabled, real mode code will first try to message a free host CPU to complete this job instead of returning the host to do it ourselves. Currently, the real mode PCI passthrough interrupt handling code checks if any of these flags are set and simply returns to the host. This is not good enough as the trap value (0x500) is treated as an external interrupt by the host code. It is only when the trap value is a hypercall that the host code searches for and acts on unfinished work by calling kvmppc_xics_rm_complete. This patch introduces a special trap BOOK3S_INTERRUPT_HV_RM_HARD which is returned by KVM if there is unfinished business to be completed in host virtual mode after handling a PCI passthrough interrupt. The host checks for this special interrupt condition and calls into the kvmppc_xics_rm_complete, which is made an exported function for this reason. [paulus@ozlabs.org - moved logic to set r12 to BOOK3S_INTERRUPT_HV_RM_HARD in book3s_hv_rmhandlers.S into the end of kvmppc_check_wake_reason.] Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2016-08-19 15:35:52 +10:00
KVM: PPC: Book3S HV P9: Stop handling hcalls in real-mode in the P9 path In the interest of minimising the amount of code that is run in "real-mode", don't handle hcalls in real mode in the P9 path. This requires some new handlers for H_CEDE and xics-on-xive to be added before xive is pulled or cede logic is checked. This introduces a change in radix guest behaviour where radix guests that execute 'sc 1' in userspace now get a privilege fault whereas previously the 'sc 1' would be reflected as a syscall interrupt to the guest kernel. That reflection is only required for hash guests that run PR KVM. Background: In POWER8 and earlier processors, it is very expensive to exit from the HV real mode context of a guest hypervisor interrupt, and switch to host virtual mode. On those processors, guest->HV interrupts reach the hypervisor with the MMU off because the MMU is loaded with guest context (LPCR, SDR1, SLB), and the other threads in the sub-core need to be pulled out of the guest too. Then the primary must save off guest state, invalidate SLB and ERAT, and load up host state before the MMU can be enabled to run in host virtual mode (~= regular Linux mode). Hash guests also require a lot of hcalls to run due to the nature of the MMU architecture and paravirtualisation design. The XICS interrupt controller requires hcalls to run. So KVM traditionally tries hard to avoid the full exit, by handling hcalls and other interrupts in real mode as much as possible. By contrast, POWER9 has independent MMU context per-thread, and in radix mode the hypervisor is in host virtual memory mode when the HV interrupt is taken. Radix guests do not require significant hcalls to manage their translations, and xive guests don't need hcalls to handle interrupts. So it's much less important for performance to handle hcalls in real mode on POWER9. One caveat is that the TCE hcalls are performance critical, real-mode variants introduced for POWER8 in order to achieve 10GbE performance. Real mode TCE hcalls were found to be less important on POWER9, which was able to drive 40GBe networking without them (using the virt mode hcalls) but performance is still important. These hcalls will benefit from subsequent guest entry/exit optimisation including possibly a faster "partial exit" that does not entirely switch to host context to handle the hcall. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210528090752.3542186-14-npiggin@gmail.com
2021-05-28 19:07:33 +10:00
KVM: PPC: Book3S HV: Set server for passed-through interrupts When a guest has a PCI pass-through device with an interrupt, it will direct the interrupt to a particular guest VCPU. In fact the physical interrupt might arrive on any CPU, and then get delivered to the target VCPU in the emulated XICS (guest interrupt controller), and eventually delivered to the target VCPU. Now that we have code to handle device interrupts in real mode without exiting to the host kernel, there is an advantage to having the device interrupt arrive on the same sub(core) as the target VCPU is running on. In this situation, the interrupt can be delivered to the target VCPU without any exit to the host kernel (using a hypervisor doorbell interrupt between threads if necessary). This patch aims to get passed-through device interrupts arriving on the correct core by setting the interrupt server in the real hardware XICS for the interrupt to the first thread in the (sub)core where its target VCPU is running. We do this in the real-mode H_EOI code because the H_EOI handler already needs to look at the emulated ICS state for the interrupt (whereas the H_XIRR handler doesn't), and we know we are running in the target VCPU context at that point. We set the server CPU in hardware using an OPAL call, regardless of what the IRQ affinity mask for the interrupt says, and without updating the affinity mask. This amounts to saying that when an interrupt is passed through to a guest, as a matter of policy we allow the guest's affinity for the interrupt to override the host's. This is inspired by an earlier patch from Suresh Warrier, although none of this code came from that earlier patch. Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2016-08-19 15:35:56 +10:00
KVM: PPC: Book3S HV: Use OPAL XICS emulation on POWER9 POWER9 includes a new interrupt controller, called XIVE, which is quite different from the XICS interrupt controller on POWER7 and POWER8 machines. KVM-HV accesses the XICS directly in several places in order to send and clear IPIs and handle interrupts from PCI devices being passed through to the guest. In order to make the transition to XIVE easier, OPAL firmware will include an emulation of XICS on top of XIVE. Access to the emulated XICS is via OPAL calls. The one complication is that the EOI (end-of-interrupt) function can now return a value indicating that another interrupt is pending; in this case, the XIVE will not signal an interrupt in hardware to the CPU, and software is supposed to acknowledge the new interrupt without waiting for another interrupt to be delivered in hardware. This adapts KVM-HV to use the OPAL calls on machines where there is no XICS hardware. When there is no XICS, we look for a device-tree node with "ibm,opal-intc" in its compatible property, which is how OPAL indicates that it provides XICS emulation. In order to handle the EOI return value, kvmppc_read_intr() has become kvmppc_read_one_intr(), with a boolean variable passed by reference which can be set by the EOI functions to indicate that another interrupt is pending. The new kvmppc_read_intr() keeps calling kvmppc_read_one_intr() until there are no more interrupts to process. The return value from kvmppc_read_intr() is the largest non-zero value of the returns from kvmppc_read_one_intr(). Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2016-11-18 09:02:08 +11:00
KVM: PPC: Book3S HV: Complete passthrough interrupt in host In existing real mode ICP code, when updating the virtual ICP state, if there is a required action that cannot be completely handled in real mode, as for instance, a VCPU needs to be woken up, flags are set in the ICP to indicate the required action. This is checked when returning from hypercalls to decide whether the call needs switch back to the host where the action can be performed in virtual mode. Note that if h_ipi_redirect is enabled, real mode code will first try to message a free host CPU to complete this job instead of returning the host to do it ourselves. Currently, the real mode PCI passthrough interrupt handling code checks if any of these flags are set and simply returns to the host. This is not good enough as the trap value (0x500) is treated as an external interrupt by the host code. It is only when the trap value is a hypercall that the host code searches for and acts on unfinished work by calling kvmppc_xics_rm_complete. This patch introduces a special trap BOOK3S_INTERRUPT_HV_RM_HARD which is returned by KVM if there is unfinished business to be completed in host virtual mode after handling a PCI passthrough interrupt. The host checks for this special interrupt condition and calls into the kvmppc_xics_rm_complete, which is made an exported function for this reason. [paulus@ozlabs.org - moved logic to set r12 to BOOK3S_INTERRUPT_HV_RM_HARD in book3s_hv_rmhandlers.S into the end of kvmppc_check_wake_reason.] Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2016-08-19 15:35:52 +10:00
KVM: PPC: Book3S HV P9: Stop handling hcalls in real-mode in the P9 path In the interest of minimising the amount of code that is run in "real-mode", don't handle hcalls in real mode in the P9 path. This requires some new handlers for H_CEDE and xics-on-xive to be added before xive is pulled or cede logic is checked. This introduces a change in radix guest behaviour where radix guests that execute 'sc 1' in userspace now get a privilege fault whereas previously the 'sc 1' would be reflected as a syscall interrupt to the guest kernel. That reflection is only required for hash guests that run PR KVM. Background: In POWER8 and earlier processors, it is very expensive to exit from the HV real mode context of a guest hypervisor interrupt, and switch to host virtual mode. On those processors, guest->HV interrupts reach the hypervisor with the MMU off because the MMU is loaded with guest context (LPCR, SDR1, SLB), and the other threads in the sub-core need to be pulled out of the guest too. Then the primary must save off guest state, invalidate SLB and ERAT, and load up host state before the MMU can be enabled to run in host virtual mode (~= regular Linux mode). Hash guests also require a lot of hcalls to run due to the nature of the MMU architecture and paravirtualisation design. The XICS interrupt controller requires hcalls to run. So KVM traditionally tries hard to avoid the full exit, by handling hcalls and other interrupts in real mode as much as possible. By contrast, POWER9 has independent MMU context per-thread, and in radix mode the hypervisor is in host virtual memory mode when the HV interrupt is taken. Radix guests do not require significant hcalls to manage their translations, and xive guests don't need hcalls to handle interrupts. So it's much less important for performance to handle hcalls in real mode on POWER9. One caveat is that the TCE hcalls are performance critical, real-mode variants introduced for POWER8 in order to achieve 10GbE performance. Real mode TCE hcalls were found to be less important on POWER9, which was able to drive 40GBe networking without them (using the virt mode hcalls) but performance is still important. These hcalls will benefit from subsequent guest entry/exit optimisation including possibly a faster "partial exit" that does not entirely switch to host context to handle the hcall. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210528090752.3542186-14-npiggin@gmail.com
2021-05-28 19:07:33 +10:00
KVM: PPC: Allow book3s_hv guests to use SMT processor modes This lifts the restriction that book3s_hv guests can only run one hardware thread per core, and allows them to use up to 4 threads per core on POWER7. The host still has to run single-threaded. This capability is advertised to qemu through a new KVM_CAP_PPC_SMT capability. The return value of the ioctl querying this capability is the number of vcpus per virtual CPU core (vcore), currently 4. To use this, the host kernel should be booted with all threads active, and then all the secondary threads should be offlined. This will put the secondary threads into nap mode. KVM will then wake them from nap mode and use them for running guest code (while they are still offline). To wake the secondary threads, we send them an IPI using a new xics_wake_cpu() function, implemented in arch/powerpc/sysdev/xics/icp-native.c. In other words, at this stage we assume that the platform has a XICS interrupt controller and we are using icp-native.c to drive it. Since the woken thread will need to acknowledge and clear the IPI, we also export the base physical address of the XICS registers using kvmppc_set_xics_phys() for use in the low-level KVM book3s code. When a vcpu is created, it is assigned to a virtual CPU core. The vcore number is obtained by dividing the vcpu number by the number of threads per core in the host. This number is exported to userspace via the KVM_CAP_PPC_SMT capability. If qemu wishes to run the guest in single-threaded mode, it should make all vcpu numbers be multiples of the number of threads per core. We distinguish three states of a vcpu: runnable (i.e., ready to execute the guest), blocked (that is, idle), and busy in host. We currently implement a policy that the vcore can run only when all its threads are runnable or blocked. This way, if a vcpu needs to execute elsewhere in the kernel or in qemu, it can do so without being starved of CPU by the other vcpus. When a vcore starts to run, it executes in the context of one of the vcpu threads. The other vcpu threads all go to sleep and stay asleep until something happens requiring the vcpu thread to return to qemu, or to wake up to run the vcore (this can happen when another vcpu thread goes from busy in host state to blocked). It can happen that a vcpu goes from blocked to runnable state (e.g. because of an interrupt), and the vcore it belongs to is already running. In that case it can start to run immediately as long as the none of the vcpus in the vcore have started to exit the guest. We send the next free thread in the vcore an IPI to get it to start to execute the guest. It synchronizes with the other threads via the vcore->entry_exit_count field to make sure that it doesn't go into the guest if the other vcpus are exiting by the time that it is ready to actually enter the guest. Note that there is no fixed relationship between the hardware thread number and the vcpu number. Hardware threads are assigned to vcpus as they become runnable, so we will always use the lower-numbered hardware threads in preference to higher-numbered threads if not all the vcpus in the vcore are runnable, regardless of which vcpus are runnable. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2011-06-29 00:23:08 +00:00
KVM: PPC: Book3S: Allow XICS emulation to work in nested hosts using XIVE Currently, the KVM code assumes that if the host kernel is using the XIVE interrupt controller (the new interrupt controller that first appeared in POWER9 systems), then the in-kernel XICS emulation will use the XIVE hardware to deliver interrupts to the guest. However, this only works when the host is running in hypervisor mode and has full access to all of the XIVE functionality. It doesn't work in any nested virtualization scenario, either with PR KVM or nested-HV KVM, because the XICS-on-XIVE code calls directly into the native-XIVE routines, which are not initialized and cannot function correctly because they use OPAL calls, and OPAL is not available in a guest. This means that using the in-kernel XICS emulation in a nested hypervisor that is using XIVE as its interrupt controller will cause a (nested) host kernel crash. To fix this, we change most of the places where the current code calls xive_enabled() to select between the XICS-on-XIVE emulation and the plain XICS emulation to call a new function, xics_on_xive(), which returns false in a guest. However, there is a further twist. The plain XICS emulation has some functions which are used in real mode and access the underlying XICS controller (the interrupt controller of the host) directly. In the case of a nested hypervisor, this means doing XICS hypercalls directly. When the nested host is using XIVE as its interrupt controller, these hypercalls will fail. Therefore this also adds checks in the places where the XICS emulation wants to access the underlying interrupt controller directly, and if that is XIVE, makes the code use the virtual mode fallback paths, which call generic kernel infrastructure rather than doing direct XICS access. Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
2019-02-04 22:07:20 +11:00
KVM: PPC: Book3S HV: Simplify machine check handling This makes the handling of machine check interrupts that occur inside a guest simpler and more robust, with less done in assembler code and in real mode. Now, when a machine check occurs inside a guest, we always get the machine check event struct and put a copy in the vcpu struct for the vcpu where the machine check occurred. We no longer call machine_check_queue_event() from kvmppc_realmode_mc_power7(), because on POWER8, when a vcpu is running on an offline secondary thread and we call machine_check_queue_event(), that calls irq_work_queue(), which doesn't work because the CPU is offline, but instead triggers the WARN_ON(lazy_irq_pending()) in pnv_smp_cpu_kill_self() (which fires again and again because nothing clears the condition). All that machine_check_queue_event() actually does is to cause the event to be printed to the console. For a machine check occurring in the guest, we now print the event in kvmppc_handle_exit_hv() instead. The assembly code at label machine_check_realmode now just calls C code and then continues exiting the guest. We no longer either synthesize a machine check for the guest in assembly code or return to the guest without a machine check. The code in kvmppc_handle_exit_hv() is extended to handle the case where the guest is not FWNMI-capable. In that case we now always synthesize a machine check interrupt for the guest. Previously, if the host thinks it has recovered the machine check fully, it would return to the guest without any notification that the machine check had occurred. If the machine check was caused by some action of the guest (such as creating duplicate SLB entries), it is much better to tell the guest that it has caused a problem. Therefore we now always generate a machine check interrupt for guests that are not FWNMI-capable. Reviewed-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com> Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-02-21 13:38:49 +11:00
KVM: PPC: Book3S HV: Host-side RM data structures This patch defines the data structures to support the setting up of host side operations while running in real mode in the guest, and also the functions to allocate and free it. The operations are for now limited to virtual XICS operations. Currently, we have only defined one operation in the data structure: - Wake up a VCPU sleeping in the host when it receives a virtual interrupt The operations are assigned at the core level because PowerKVM requires that the host run in SMT off mode. For each core, we will need to manage its state atomically - where the state is defined by: 1. Is the core running in the host? 2. Is there a Real Mode (RM) operation pending on the host? Currently, core state is only managed at the whole-core level even when the system is in split-core mode. This just limits the number of free or "available" cores in the host to perform any host-side operations. The kvmppc_host_rm_core.rm_data allows any data to be passed by KVM in real mode to the host core along with the operation to be performed. The kvmppc_host_rm_ops structure is allocated the very first time a guest VM is started. Initial core state is also set - all online cores are in the host. This structure is never deleted, not even when there are no active guests. However, it needs to be freed when the module is unloaded because the kvmppc_host_rm_ops_hv can contain function pointers to kvm-hv.ko functions for the different supported host operations. Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2015-12-17 14:59:06 -06:00
kvm: rename pfn_t to kvm_pfn_t To date, we have implemented two I/O usage models for persistent memory, PMEM (a persistent "ram disk") and DAX (mmap persistent memory into userspace). This series adds a third, DAX-GUP, that allows DAX mappings to be the target of direct-i/o. It allows userspace to coordinate DMA/RDMA from/to persistent memory. The implementation leverages the ZONE_DEVICE mm-zone that went into 4.3-rc1 (also discussed at kernel summit) to flag pages that are owned and dynamically mapped by a device driver. The pmem driver, after mapping a persistent memory range into the system memmap via devm_memremap_pages(), arranges for DAX to distinguish pfn-only versus page-backed pmem-pfns via flags in the new pfn_t type. The DAX code, upon seeing a PFN_DEV+PFN_MAP flagged pfn, flags the resulting pte(s) inserted into the process page tables with a new _PAGE_DEVMAP flag. Later, when get_user_pages() is walking ptes it keys off _PAGE_DEVMAP to pin the device hosting the page range active. Finally, get_page() and put_page() are modified to take references against the device driver established page mapping. Finally, this need for "struct page" for persistent memory requires memory capacity to store the memmap array. Given the memmap array for a large pool of persistent may exhaust available DRAM introduce a mechanism to allocate the memmap from persistent memory. The new "struct vmem_altmap *" parameter to devm_memremap_pages() enables arch_add_memory() to use reserved pmem capacity rather than the page allocator. This patch (of 18): The core has developed a need for a "pfn_t" type [1]. Move the existing pfn_t in KVM to kvm_pfn_t [2]. [1]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002199.html [2]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002218.html Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Christoffer Dall <christoffer.dall@linaro.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-15 16:56:11 -08:00
mm: introduce memdesc_flags_t Patch series "Add and use memdesc_flags_t". At some point struct page will be separated from struct slab and struct folio. This is a step towards that by introducing a type for the 'flags' word of all three structures. This gives us a certain amount of type safety by establishing that some of these unsigned longs are different from other unsigned longs in that they contain things like node ID, section number and zone number in the upper bits. That lets us have functions that can be easily called by anyone who has a slab, folio or page (but not easily by anyone else) to get the node or zone. There's going to be some unusual merge problems with this as some odd bits of the kernel decide they want to print out the flags value or something similar by writing page->flags and now they'll need to write page->flags.f instead. That's most of the churn here. Maybe we should be removing these things from the debug output? This patch (of 11): Wrap the unsigned long flags in a typedef. In upcoming patches, this will provide a strong hint that you can't just pass a random unsigned long to functions which take this as an argument. [willy@infradead.org: s/flags/flags.f/ in several architectures] Link: https://lkml.kernel.org/r/aKMgPRLD-WnkPxYm@casper.infradead.org [nicola.vetrini@gmail.com: mips: fix compilation error] Link: https://lore.kernel.org/lkml/CA+G9fYvkpmqGr6wjBNHY=dRp71PLCoi2341JxOudi60yqaeUdg@mail.gmail.com/ Link: https://lkml.kernel.org/r/20250825214245.1838158-1-nicola.vetrini@gmail.com Link: https://lkml.kernel.org/r/20250805172307.1302730-1-willy@infradead.org Link: https://lkml.kernel.org/r/20250805172307.1302730-2-willy@infradead.org Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Zi Yan <ziy@nvidia.com> Cc: Shakeel Butt <shakeel.butt@linux.dev> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2025-08-05 18:22:51 +01:00
mm: introduce memdesc_flags_t Patch series "Add and use memdesc_flags_t". At some point struct page will be separated from struct slab and struct folio. This is a step towards that by introducing a type for the 'flags' word of all three structures. This gives us a certain amount of type safety by establishing that some of these unsigned longs are different from other unsigned longs in that they contain things like node ID, section number and zone number in the upper bits. That lets us have functions that can be easily called by anyone who has a slab, folio or page (but not easily by anyone else) to get the node or zone. There's going to be some unusual merge problems with this as some odd bits of the kernel decide they want to print out the flags value or something similar by writing page->flags and now they'll need to write page->flags.f instead. That's most of the churn here. Maybe we should be removing these things from the debug output? This patch (of 11): Wrap the unsigned long flags in a typedef. In upcoming patches, this will provide a strong hint that you can't just pass a random unsigned long to functions which take this as an argument. [willy@infradead.org: s/flags/flags.f/ in several architectures] Link: https://lkml.kernel.org/r/aKMgPRLD-WnkPxYm@casper.infradead.org [nicola.vetrini@gmail.com: mips: fix compilation error] Link: https://lore.kernel.org/lkml/CA+G9fYvkpmqGr6wjBNHY=dRp71PLCoi2341JxOudi60yqaeUdg@mail.gmail.com/ Link: https://lkml.kernel.org/r/20250825214245.1838158-1-nicola.vetrini@gmail.com Link: https://lkml.kernel.org/r/20250805172307.1302730-1-willy@infradead.org Link: https://lkml.kernel.org/r/20250805172307.1302730-2-willy@infradead.org Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Zi Yan <ziy@nvidia.com> Cc: Shakeel Butt <shakeel.butt@linux.dev> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2025-08-05 18:22:51 +01:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00
KVM: PPC: Add support for nestedv2 guests A series of hcalls have been added to the PAPR which allow a regular guest partition to create and manage guest partitions of its own. KVM already had an interface that allowed this on powernv platforms. This existing interface will now be called "nestedv1". The newly added PAPR interface will be called "nestedv2". PHYP will support the nestedv2 interface. At this time the host side of the nestedv2 interface has not been implemented on powernv but there is no technical reason why it could not be added. The nestedv1 interface is still supported. Add support to KVM to utilize these hcalls to enable running nested guests as a pseries guest on PHYP. Overview of the new hcall usage: - L1 and L0 negotiate capabilities with H_GUEST_{G,S}ET_CAPABILITIES() - L1 requests the L0 create a L2 with H_GUEST_CREATE() and receives a handle to use in future hcalls - L1 requests the L0 create a L2 vCPU with H_GUEST_CREATE_VCPU() - L1 sets up the L2 using H_GUEST_SET and the H_GUEST_VCPU_RUN input buffer - L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN() - L2 returns to L1 with an exit reason and L1 reads the H_GUEST_VCPU_RUN output buffer populated by the L0 - L1 handles the exit using H_GET_STATE if necessary - L1 reruns L2 vCPU with H_GUEST_VCPU_RUN - L1 frees the L2 in the L0 with H_GUEST_DELETE() Support for the new API is determined by trying H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2 interface. Use the vcpu register state setters for tracking modified guest state elements and copy the thread wide values into the H_GUEST_VCPU_RUN input buffer immediately before running a L2. The guest wide elements can not be added to the input buffer so send them with a separate H_GUEST_SET call if necessary. Make the vcpu register getter load the corresponding value from the real host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track which values have already been loaded between H_GUEST_VCPU_RUN calls. If an element is present in the H_GUEST_VCPU_RUN output buffer it also does not need to be loaded again. Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Gautam Menghani <gautam@linux.ibm.com> Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com> Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com> Signed-off-by: Jordan Niethe <jniethe5@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com
2023-09-14 13:05:59 +10:00