linux/drivers/bluetooth/hci_h5.c

1176 lines
26 KiB

Bluetooth: hci_h5: Disable the hci_suspend_notifier for btrtl devices The hci_suspend_notifier which was introduced last year, is causing problems for uart attached btrtl devices. These devices may loose their firmware and their baudrate setting over a suspend/resume. Since we don't even know the baudrate after a suspend/resume recovering from this is tricky. The driver solves this by treating these devices the same as USB BT HCIs which drop of the bus during suspend. Specifically the driver: 1. Simply unconditionally turns the device fully off during system-suspend to save maximum power. 2. Calls device_reprobe() from a workqueue to fully re-init the device from scratch on system-resume (unregistering the old HCI and registering a new HCI). This means that these devices do not benefit from the suspend / resume handling work done by the hci_suspend_notifier. At best this unnecessarily adds some time to the suspend/resume time. But in practice this is actually causing problems: 1. These btrtl devices seem to not like the HCI_OP_WRITE_SCAN_ENABLE( SCAN_DISABLED) request being send to them when entering the BT_SUSPEND_CONFIGURE_WAKE state. The same request send on BT_SUSPEND_DISCONNECT works fine, but the second one send (unnecessarily?) from the BT_SUSPEND_CONFIGURE_WAKE transition causes the device to hang: [ 573.497754] PM: suspend entry (s2idle) [ 573.554615] Filesystems sync: 0.056 seconds [ 575.837753] Bluetooth: hci0: Timed out waiting for suspend events [ 575.837801] Bluetooth: hci0: Suspend timeout bit: 4 [ 575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -110 2. The PM_POST_SUSPEND / BT_RUNNING transition races with the driver-unbinding done by the device_reprobe() work. If the hci_suspend_notifier wins the race it is talking to a dead device leading to the following errors being logged: [ 598.686060] Bluetooth: hci0: Timed out waiting for suspend events [ 598.686124] Bluetooth: hci0: Suspend timeout bit: 5 [ 598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110 In both cases things still work, but the suspend-notifier is causing these ugly errors getting logged and ut increase both the suspend- and the resume-time by 2 seconds. This commit avoids these problems by disabling the hci_suspend_notifier. Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Vasily Khoruzhick <anarsoul@gmail.com> Cc: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-06-29 21:59:07 +02:00
Bluetooth: hci_h5: Disable the hci_suspend_notifier for btrtl devices The hci_suspend_notifier which was introduced last year, is causing problems for uart attached btrtl devices. These devices may loose their firmware and their baudrate setting over a suspend/resume. Since we don't even know the baudrate after a suspend/resume recovering from this is tricky. The driver solves this by treating these devices the same as USB BT HCIs which drop of the bus during suspend. Specifically the driver: 1. Simply unconditionally turns the device fully off during system-suspend to save maximum power. 2. Calls device_reprobe() from a workqueue to fully re-init the device from scratch on system-resume (unregistering the old HCI and registering a new HCI). This means that these devices do not benefit from the suspend / resume handling work done by the hci_suspend_notifier. At best this unnecessarily adds some time to the suspend/resume time. But in practice this is actually causing problems: 1. These btrtl devices seem to not like the HCI_OP_WRITE_SCAN_ENABLE( SCAN_DISABLED) request being send to them when entering the BT_SUSPEND_CONFIGURE_WAKE state. The same request send on BT_SUSPEND_DISCONNECT works fine, but the second one send (unnecessarily?) from the BT_SUSPEND_CONFIGURE_WAKE transition causes the device to hang: [ 573.497754] PM: suspend entry (s2idle) [ 573.554615] Filesystems sync: 0.056 seconds [ 575.837753] Bluetooth: hci0: Timed out waiting for suspend events [ 575.837801] Bluetooth: hci0: Suspend timeout bit: 4 [ 575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -110 2. The PM_POST_SUSPEND / BT_RUNNING transition races with the driver-unbinding done by the device_reprobe() work. If the hci_suspend_notifier wins the race it is talking to a dead device leading to the following errors being logged: [ 598.686060] Bluetooth: hci0: Timed out waiting for suspend events [ 598.686124] Bluetooth: hci0: Suspend timeout bit: 5 [ 598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110 In both cases things still work, but the suspend-notifier is causing these ugly errors getting logged and ut increase both the suspend- and the resume-time by 2 seconds. This commit avoids these problems by disabling the hci_suspend_notifier. Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Vasily Khoruzhick <anarsoul@gmail.com> Cc: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-06-29 21:59:07 +02:00
Bluetooth: btrtl: fix out of bounds memory access The problem is detected by KASAN. btrtl driver uses private hci data to store 'struct btrealtek_data'. If btrtl driver is used with btusb, then memory for private hci data is allocated in btusb. But no private data is allocated after hci_dev, when btrtl is used with hci_h5. This commit adds memory allocation for hci_h5 case. ================================================================== BUG: KASAN: slab-out-of-bounds in btrtl_initialize+0x6cc/0x958 [btrtl] Write of size 8 at addr ffff00000f5a5748 by task kworker/u9:0/76 Hardware name: Pine64 PinePhone (1.2) (DT) Workqueue: hci0 hci_power_on [bluetooth] Call trace: dump_backtrace+0x9c/0x128 show_stack+0x20/0x38 dump_stack_lvl+0x48/0x60 print_report+0xf8/0x5d8 kasan_report+0x90/0xd0 __asan_store8+0x9c/0xc0 [btrtl] h5_btrtl_setup+0xd0/0x2f8 [hci_uart] h5_setup+0x50/0x80 [hci_uart] hci_uart_setup+0xd4/0x260 [hci_uart] hci_dev_open_sync+0x1cc/0xf68 [bluetooth] hci_dev_do_open+0x34/0x90 [bluetooth] hci_power_on+0xc4/0x3c8 [bluetooth] process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Allocated by task 53: kasan_save_stack+0x3c/0x68 kasan_save_track+0x20/0x40 kasan_save_alloc_info+0x68/0x78 __kasan_kmalloc+0xd4/0xd8 __kmalloc+0x1b4/0x3b0 hci_alloc_dev_priv+0x28/0xa58 [bluetooth] hci_uart_register_device+0x118/0x4f8 [hci_uart] h5_serdev_probe+0xf4/0x178 [hci_uart] serdev_drv_probe+0x54/0xa0 really_probe+0x254/0x588 __driver_probe_device+0xc4/0x210 driver_probe_device+0x64/0x160 __driver_attach_async_helper+0x88/0x158 async_run_entry_fn+0xd0/0x388 process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Last potentially related work creation: kasan_save_stack+0x3c/0x68 __kasan_record_aux_stack+0xb0/0x150 kasan_record_aux_stack_noalloc+0x14/0x20 __queue_work+0x33c/0x960 queue_work_on+0x98/0xc0 hci_recv_frame+0xc8/0x1e8 [bluetooth] h5_complete_rx_pkt+0x2c8/0x800 [hci_uart] h5_rx_payload+0x98/0xb8 [hci_uart] h5_recv+0x158/0x3d8 [hci_uart] hci_uart_receive_buf+0xa0/0xe8 [hci_uart] ttyport_receive_buf+0xac/0x178 flush_to_ldisc+0x130/0x2c8 process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Second to last potentially related work creation: kasan_save_stack+0x3c/0x68 __kasan_record_aux_stack+0xb0/0x150 kasan_record_aux_stack_noalloc+0x14/0x20 __queue_work+0x788/0x960 queue_work_on+0x98/0xc0 __hci_cmd_sync_sk+0x23c/0x7a0 [bluetooth] __hci_cmd_sync+0x24/0x38 [bluetooth] btrtl_initialize+0x760/0x958 [btrtl] h5_btrtl_setup+0xd0/0x2f8 [hci_uart] h5_setup+0x50/0x80 [hci_uart] hci_uart_setup+0xd4/0x260 [hci_uart] hci_dev_open_sync+0x1cc/0xf68 [bluetooth] hci_dev_do_open+0x34/0x90 [bluetooth] hci_power_on+0xc4/0x3c8 [bluetooth] process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 ================================================================== Fixes: 5b355944b190 ("Bluetooth: btrtl: Add btrealtek data struct") Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support") Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-02-24 00:37:04 +03:00