linux/drivers/irqchip/qcom-pdc.c

452 lines
12 KiB

irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Fix phantom irq when changing between rising/falling We have a problem if we use gpio-keys and configure wakeups such that we only want one edge to wake us up. AKA: wakeup-event-action = <EV_ACT_DEASSERTED>; wakeup-source; Specifically we end up with a phantom interrupt that blocks suspend if the line was already high and we want wakeups on rising edges (AKA we want the GPIO to go low and then high again before we wake up). The opposite is also problematic. Specifically, here's what's happening today: 1. Normally, gpio-keys configures to look for both edges. Due to the current workaround introduced in commit c3c0c2e18d94 ("pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180"), if the line was high we'd configure for falling edges. 2. At suspend time, we change to look for rising edges. 3. After qcom_pdc_gic_set_type() runs, we get a phantom interrupt. We can solve this by just clearing the phantom interrupt. NOTE: it is possible that this could cause problems for a client with very specific needs, but there's not much we can do with this hardware. As an example, let's say the interrupt signal is currently high and the client is looking for falling edges. The client now changes to look for rising edges. The client could possibly expect that if the line has a short pulse low (and back high) that it would always be detected. Specifically no matter when the pulse happened, it should either have tripped the (old) falling edge trigger or the (new) rising edge trigger. We will simply not trip it. We could narrow down the race a bit by polling our parent before changing types, but no matter what we do there will still be a period of time where we can't tell the difference between a real transition (or more than one transition) and the phantom. Fixes: f55c73aef890 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs") Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Tested-by: Maulik Shah <mkshah@codeaurora.org> Reviewed-by: Maulik Shah <mkshah@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20201211141514.v4.1.I2702919afc253e2a451bebc3b701b462b2d22344@changeid
2020-12-11 14:15:35 -08:00
irqchip/qcom-pdc: Fix phantom irq when changing between rising/falling We have a problem if we use gpio-keys and configure wakeups such that we only want one edge to wake us up. AKA: wakeup-event-action = <EV_ACT_DEASSERTED>; wakeup-source; Specifically we end up with a phantom interrupt that blocks suspend if the line was already high and we want wakeups on rising edges (AKA we want the GPIO to go low and then high again before we wake up). The opposite is also problematic. Specifically, here's what's happening today: 1. Normally, gpio-keys configures to look for both edges. Due to the current workaround introduced in commit c3c0c2e18d94 ("pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180"), if the line was high we'd configure for falling edges. 2. At suspend time, we change to look for rising edges. 3. After qcom_pdc_gic_set_type() runs, we get a phantom interrupt. We can solve this by just clearing the phantom interrupt. NOTE: it is possible that this could cause problems for a client with very specific needs, but there's not much we can do with this hardware. As an example, let's say the interrupt signal is currently high and the client is looking for falling edges. The client now changes to look for rising edges. The client could possibly expect that if the line has a short pulse low (and back high) that it would always be detected. Specifically no matter when the pulse happened, it should either have tripped the (old) falling edge trigger or the (new) rising edge trigger. We will simply not trip it. We could narrow down the race a bit by polling our parent before changing types, but no matter what we do there will still be a period of time where we can't tell the difference between a real transition (or more than one transition) and the phantom. Fixes: f55c73aef890 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs") Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Tested-by: Maulik Shah <mkshah@codeaurora.org> Reviewed-by: Maulik Shah <mkshah@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20201211141514.v4.1.I2702919afc253e2a451bebc3b701b462b2d22344@changeid
2020-12-11 14:15:35 -08:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00
irqchip/qcom-pdc: Workaround hardware register bug on X1E80100 On X1E80100, there is a hardware bug in the register logic of the IRQ_ENABLE_BANK register: While read accesses work on the normal address, all write accesses must be made to a shifted address. Without a workaround for this, the wrong interrupt gets enabled in the PDC and it is impossible to wakeup from deep suspend (CX collapse). This has not caused problems so far, because the deep suspend state was not enabled. A workaround is required now since work is ongoing to fix this. The PDC has multiple "DRV" regions, each one has a size of 0x10000 and provides the same set of registers for a particular client in the system. Linux is one the clients and uses DRV region 2 on X1E. Each "bank" inside the DRV region consists of 32 interrupt pins that can be enabled using the IRQ_ENABLE_BANK register: IRQ_ENABLE_BANK[bank] = base + IRQ_ENABLE_BANK + bank * sizeof(u32) On X1E, this works as intended for read access. However, write access to most banks is shifted by 2: IRQ_ENABLE_BANK_X1E[0] = IRQ_ENABLE_BANK[-2] IRQ_ENABLE_BANK_X1E[1] = IRQ_ENABLE_BANK[-1] IRQ_ENABLE_BANK_X1E[2] = IRQ_ENABLE_BANK[0] = IRQ_ENABLE_BANK[2 - 2] IRQ_ENABLE_BANK_X1E[3] = IRQ_ENABLE_BANK[1] = IRQ_ENABLE_BANK[3 - 2] IRQ_ENABLE_BANK_X1E[4] = IRQ_ENABLE_BANK[2] = IRQ_ENABLE_BANK[4 - 2] IRQ_ENABLE_BANK_X1E[5] = IRQ_ENABLE_BANK[5] (this one works as intended) The negative indexes underflow to banks of the previous DRV/client region: IRQ_ENABLE_BANK_X1E[drv 2][bank 0] = IRQ_ENABLE_BANK[drv 2][bank -2] = IRQ_ENABLE_BANK[drv 1][bank 5-2] = IRQ_ENABLE_BANK[drv 1][bank 3] = IRQ_ENABLE_BANK[drv 1][bank 0 + 3] IRQ_ENABLE_BANK_X1E[drv 2][bank 1] = IRQ_ENABLE_BANK[drv 2][bank -1] = IRQ_ENABLE_BANK[drv 1][bank 5-1] = IRQ_ENABLE_BANK[drv 1][bank 4] = IRQ_ENABLE_BANK[drv 1][bank 1 + 3] Introduce a workaround for the bug by matching the qcom,x1e80100-pdc compatible and apply the offsets as shown above: - Bank 0...1: previous DRV region, bank += 3 - Bank 1...4: our DRV region, bank -= 2 - Bank 5: our DRV region, no fixup required The PDC node in the device tree only describes the DRV region for the Linux client, but the workaround also requires to map parts of the previous DRV region to issue writes there. To maintain compatibility with old device trees, obtain the base address of the preceeding region by applying the -0x10000 offset. Note that this is also more correct from a conceptual point of view: It does not really make use of the other region; it just issues shifted writes that end up in the registers of the Linux associated DRV region 2. Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/all/20250218-x1e80100-pdc-hw-wa-v2-1-29be4c98e355@linaro.org
2025-02-18 16:59:18 +01:00