linux/drivers/regulator/fan53555.c

795 lines
19 KiB

regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: fan53555: add enable_time support and soft-start times The datasheets for all the fan53555 variants (and clones using the same interface) define so called soft start times, from enabling the regulator until at least some percentage of the output (i.e. 92% for the rk860x types) are available. The regulator framework supports this with the enable_time property but currently the fan53555 driver does not define enable_times for any variant. I ran into a problem with this while testing the new driver for the Rockchip NPUs (rocket), which does runtime-pm including disabling and enabling a rk8602 as needed. When reenabling the regulator while running a load, fatal hangs could be observed while enabling the associated power-domain, which the regulator supplies. Experimentally setting the regulator to always-on, made the issue disappear, leading to the missing delay to let power stabilize. And as expected, setting the enable-time to a non-zero value according to the datasheet also resolved the regulator-issue. The datasheets in nearly all cases only specify "typical" values, except for the fan53555 type 08. There both a typical and maximum value are listed - 40uS apart. For all typical values I've added 100uS to be on the safe side. Individual details for the relevant regulators below: - fan53526: The datasheet for all variants lists a typical value of 150uS, so make that 250uS with safety margin. - fan53555: types 08 and 18 (unsupported) are given a typical enable time of 135uS but also a maximum of 175uS so use that value. All the other types only have a typical time in the datasheet of 300uS, so give a bit margin by setting it to 400uS. - rk8600 + rk8602: Datasheet reports a typical value of 260us, so use 360uS to be safe. - syr82x + syr83x: All datasheets report typical soft-start values of 300uS for these regulators, so use 400uS. - tcs452x: Datasheet sadly does not report a soft-start time, so I've not set an enable-time Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20250606190418.478633-1-heiko@sntech.de Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-06 21:04:18 +02:00
regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14 Probing of regulators can be a slow operation and can contribute to slower boot times. This is especially true if a regulator is turned on at probe time (with regulator-boot-on or regulator-always-on) and the regulator requires delays (off-on-time, ramp time, etc). While the overall kernel is not ready to switch to async probe by default, as per the discussion on the mailing lists [1] it is believed that the regulator subsystem is in good shape and we can move regulator drivers over wholesale. There is no way to just magically opt in all regulators (regulators are just normal drivers like platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all regulators found in 'drivers/regulator' individually. Given the number of drivers touched and the impossibility to test this ahead of time, it wouldn't be shocking at all if this caused a regression for someone. If there is a regression caused by this patch, it's likely to be one of the cases talked about in [1]. As a "quick fix", drivers involved in the regression could be fixed by changing them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix would be to directly fix the problem that caused the issue with async probe. The approach here follows a similar approach that was used for the mmc subsystem several years ago [2]. In fact, I ran nearly the same python script to auto-generate the changes. The only thing I changed was to search for "i2c_driver", "spmi_driver", and "spi_driver" in addition to "platform_driver". [1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk [2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/ Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2023-03-16 12:54:38 -07:00