2019-05-27 08:55:01 +02:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-11 13:59:13 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-08-08 00:50:19 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
2012-06-03 21:31:09 +02:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
2012-03-22 14:08:04 +08:00
|
|
|
|
2012-08-08 00:50:19 +02:00
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2012-06-03 21:31:09 +02:00
|
|
|
|
2012-06-03 21:32:05 +02:00
|
|
|
|
|
|
|
|
|
2012-06-03 21:31:09 +02:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2012-03-22 14:08:04 +08:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-08-08 00:50:19 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
2012-08-08 00:50:19 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
2019-03-08 14:15:29 +08:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-01-28 22:17:46 +08:00
|
|
|
|
2014-11-10 14:43:53 +01:00
|
|
|
|
|
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
2013-11-09 13:12:28 +01:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-11-10 14:43:53 +01:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-07-20 21:28:09 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-11-19 14:13:06 +00:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
2014-02-13 16:34:32 +01:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
2014-01-30 21:25:14 -08:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-02-13 16:34:32 +01:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
2014-02-12 01:01:08 +01:00
|
|
|
|
|
|
|
|
|
2012-11-14 11:51:36 +00:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
treewide: devm_kzalloc() -> devm_kcalloc()
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:
devm_kzalloc(handle, a * b, gfp)
with:
devm_kcalloc(handle, a * b, gfp)
as well as handling cases of:
devm_kzalloc(handle, a * b * c, gfp)
with:
devm_kzalloc(handle, array3_size(a, b, c), gfp)
as it's slightly less ugly than:
devm_kcalloc(handle, array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
devm_kzalloc(handle, 4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@
(
devm_kzalloc(HANDLE,
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
devm_kzalloc(HANDLE,
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@
(
devm_kzalloc(HANDLE,
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@
(
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE,
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * E2
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * (E2)
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 14:07:58 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-02-12 01:01:08 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-12-05 00:29:57 +00:00
|
|
|
|
2013-11-09 13:12:28 +01:00
|
|
|
|
2013-12-05 00:29:57 +00:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-12-05 19:09:55 +00:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-11-09 13:12:28 +01:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
2023-03-10 08:47:21 -06:00
|
|
|
|
2022-09-29 15:25:25 +02:00
|
|
|
|
|
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-03-08 14:15:29 +08:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-11-19 13:22:22 -05:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2012-04-04 00:50:22 +01:00
|
|
|
|
2019-03-08 14:15:28 +08:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
2025-05-12 13:57:27 -05:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
2012-04-03 23:20:56 +01:00
|
|
|
|
2014-01-24 15:48:18 -02:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
2014-11-10 14:43:53 +01:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
2014-11-10 14:43:53 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
2018-03-13 21:33:11 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
2025-07-03 16:05:49 +05:30
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-09-29 15:25:25 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-04 10:19:46 +08:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
2012-04-04 00:50:22 +01:00
|
|
|
|
2012-06-03 21:30:33 +02:00
|
|
|
|
2012-11-12 17:59:52 +08:00
|
|
|
|
2012-04-04 00:50:22 +01:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
2020-06-09 13:46:09 +01:00
|
|
|
|
2019-01-29 11:31:52 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-01-29 11:31:55 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-04 10:20:46 +08:00
|
|
|
|
2019-03-08 14:15:28 +08:00
|
|
|
|
2025-05-12 13:57:27 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-12-04 10:32:05 +08:00
|
|
|
|
2012-12-21 13:26:06 -08:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2015-09-18 19:09:24 +02:00
|
|
|
|
2012-12-04 10:32:05 +08:00
|
|
|
|
2012-10-15 14:16:59 +01:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14
Probing of regulators can be a slow operation and can contribute to
slower boot times. This is especially true if a regulator is turned on
at probe time (with regulator-boot-on or regulator-always-on) and the
regulator requires delays (off-on-time, ramp time, etc).
While the overall kernel is not ready to switch to async probe by
default, as per the discussion on the mailing lists [1] it is believed
that the regulator subsystem is in good shape and we can move
regulator drivers over wholesale. There is no way to just magically
opt in all regulators (regulators are just normal drivers like
platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all
regulators found in 'drivers/regulator' individually.
Given the number of drivers touched and the impossibility to test this
ahead of time, it wouldn't be shocking at all if this caused a
regression for someone. If there is a regression caused by this patch,
it's likely to be one of the cases talked about in [1]. As a "quick
fix", drivers involved in the regression could be fixed by changing
them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix
would be to directly fix the problem that caused the issue with async
probe.
The approach here follows a similar approach that was used for the mmc
subsystem several years ago [2]. In fact, I ran nearly the same python
script to auto-generate the changes. The only thing I changed was to
search for "i2c_driver", "spmi_driver", and "spi_driver" in addition
to "platform_driver".
[1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk
[2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-03-16 12:54:38 -07:00
|
|
|
|
2012-12-04 10:32:05 +08:00
|
|
|
|
regulator: Add driver for gpio-controlled regulators
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-05 12:27:05 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|