linux/fs/gfs2/lock_dlm.c

1462 lines
42 KiB

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 17:04:11 +09:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
gfs2: Expect -EBUSY after canceling dlm locking requests Due to the asynchronous nature of the dlm api, when we request a pending locking request to be canceled with dlm_unlock(DLM_LKF_CANCEL), the locking request will either complete before it could be canceled, or the cancellation will succeed. In either case, gdlm_ast will be called once and the status will indicate the outcome of the locking request, with -DLM_ECANCEL indicating a canceled request. Inside dlm, when a locking request completes before its cancel request could be processed, gdlm_ast will be called, but the lock will still be considered busy until a DLM_MSG_CANCEL_REPLY message completes the cancel request. During that time, successive dlm_lock() or dlm_unlock() requests for that lock will return -EBUSY. In other words, waiting for the gdlm_ast call before issuing the next locking request is not enough. There is no way of waiting for a cancel request to actually complete, either. We rarely cancel locking requests, but when we do, we don't know when the next locking request for that lock will occur. This means that any dlm_lock() or dlm_unlock() call can potentially return -EBUSY. When that happens, this patch simply repeats the request after a short pause. This workaround could be improved upon by tracking for which dlm locks cancel requests have been issued, but that isn't strictly necessary and it would complicate the code. We haven't seen -EBUSY errors from dlm without cancel requests. Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2022-02-02 11:00:48 +01:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
gfs2: Expect -EBUSY after canceling dlm locking requests Due to the asynchronous nature of the dlm api, when we request a pending locking request to be canceled with dlm_unlock(DLM_LKF_CANCEL), the locking request will either complete before it could be canceled, or the cancellation will succeed. In either case, gdlm_ast will be called once and the status will indicate the outcome of the locking request, with -DLM_ECANCEL indicating a canceled request. Inside dlm, when a locking request completes before its cancel request could be processed, gdlm_ast will be called, but the lock will still be considered busy until a DLM_MSG_CANCEL_REPLY message completes the cancel request. During that time, successive dlm_lock() or dlm_unlock() requests for that lock will return -EBUSY. In other words, waiting for the gdlm_ast call before issuing the next locking request is not enough. There is no way of waiting for a cancel request to actually complete, either. We rarely cancel locking requests, but when we do, we don't know when the next locking request for that lock will occur. This means that any dlm_lock() or dlm_unlock() call can potentially return -EBUSY. When that happens, this patch simply repeats the request after a short pause. This workaround could be improved upon by tracking for which dlm locks cancel requests have been issued, but that isn't strictly necessary and it would complicate the code. We haven't seen -EBUSY errors from dlm without cancel requests. Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2022-02-02 11:00:48 +01:00
gfs2: Expect -EBUSY after canceling dlm locking requests Due to the asynchronous nature of the dlm api, when we request a pending locking request to be canceled with dlm_unlock(DLM_LKF_CANCEL), the locking request will either complete before it could be canceled, or the cancellation will succeed. In either case, gdlm_ast will be called once and the status will indicate the outcome of the locking request, with -DLM_ECANCEL indicating a canceled request. Inside dlm, when a locking request completes before its cancel request could be processed, gdlm_ast will be called, but the lock will still be considered busy until a DLM_MSG_CANCEL_REPLY message completes the cancel request. During that time, successive dlm_lock() or dlm_unlock() requests for that lock will return -EBUSY. In other words, waiting for the gdlm_ast call before issuing the next locking request is not enough. There is no way of waiting for a cancel request to actually complete, either. We rarely cancel locking requests, but when we do, we don't know when the next locking request for that lock will occur. This means that any dlm_lock() or dlm_unlock() call can potentially return -EBUSY. When that happens, this patch simply repeats the request after a short pause. This workaround could be improved upon by tracking for which dlm locks cancel requests have been issued, but that isn't strictly necessary and it would complicate the code. We haven't seen -EBUSY errors from dlm without cancel requests. Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2022-02-02 11:00:48 +01:00
GFS2: glock statistics gathering The stats are divided into two sets: those relating to the super block and those relating to an individual glock. The super block stats are done on a per cpu basis in order to try and reduce the overhead of gathering them. They are also further divided by glock type. In the case of both the super block and glock statistics, the same information is gathered in each case. The super block statistics are used to provide default values for most of the glock statistics, so that newly created glocks should have, as far as possible, a sensible starting point. The statistics are divided into three pairs of mean and variance, plus two counters. The mean/variance pairs are smoothed exponential estimates and the algorithm used is one which will be very familiar to those used to calculation of round trip times in network code. The three pairs of mean/variance measure the following things: 1. DLM lock time (non-blocking requests) 2. DLM lock time (blocking requests) 3. Inter-request time (again to the DLM) A non-blocking request is one which will complete right away, whatever the state of the DLM lock in question. That currently means any requests when (a) the current state of the lock is exclusive (b) the requested state is either null or unlocked or (c) the "try lock" flag is set. A blocking request covers all the other lock requests. There are two counters. The first is there primarily to show how many lock requests have been made, and thus how much data has gone into the mean/variance calculations. The other counter is counting queueing of holders at the top layer of the glock code. Hopefully that number will be a lot larger than the number of dlm lock requests issued. So why gather these statistics? There are several reasons we'd like to get a better idea of these timings: 1. To be able to better set the glock "min hold time" 2. To spot performance issues more easily 3. To improve the algorithm for selecting resource groups for allocation (to base it on lock wait time, rather than blindly using a "try lock") Due to the smoothing action of the updates, a step change in some input quantity being sampled will only fully be taken into account after 8 samples (or 4 for the variance) and this needs to be carefully considered when interpreting the results. Knowing both the time it takes a lock request to complete and the average time between lock requests for a glock means we can compute the total percentage of the time for which the node is able to use a glock vs. time that the rest of the cluster has its share. That will be very useful when setting the lock min hold time. The other point to remember is that all times are in nanoseconds. Great care has been taken to ensure that we measure exactly the quantities that we want, as accurately as possible. There are always inaccuracies in any measuring system, but I hope this is as accurate as we can reasonably make it. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2012-01-20 10:38:36 +00:00
gfs2: Expect -EBUSY after canceling dlm locking requests Due to the asynchronous nature of the dlm api, when we request a pending locking request to be canceled with dlm_unlock(DLM_LKF_CANCEL), the locking request will either complete before it could be canceled, or the cancellation will succeed. In either case, gdlm_ast will be called once and the status will indicate the outcome of the locking request, with -DLM_ECANCEL indicating a canceled request. Inside dlm, when a locking request completes before its cancel request could be processed, gdlm_ast will be called, but the lock will still be considered busy until a DLM_MSG_CANCEL_REPLY message completes the cancel request. During that time, successive dlm_lock() or dlm_unlock() requests for that lock will return -EBUSY. In other words, waiting for the gdlm_ast call before issuing the next locking request is not enough. There is no way of waiting for a cancel request to actually complete, either. We rarely cancel locking requests, but when we do, we don't know when the next locking request for that lock will occur. This means that any dlm_lock() or dlm_unlock() call can potentially return -EBUSY. When that happens, this patch simply repeats the request after a short pause. This workaround could be improved upon by tracking for which dlm locks cancel requests have been issued, but that isn't strictly necessary and it would complicate the code. We haven't seen -EBUSY errors from dlm without cancel requests. Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2022-02-02 11:00:48 +01:00
gfs2: Expect -EBUSY after canceling dlm locking requests Due to the asynchronous nature of the dlm api, when we request a pending locking request to be canceled with dlm_unlock(DLM_LKF_CANCEL), the locking request will either complete before it could be canceled, or the cancellation will succeed. In either case, gdlm_ast will be called once and the status will indicate the outcome of the locking request, with -DLM_ECANCEL indicating a canceled request. Inside dlm, when a locking request completes before its cancel request could be processed, gdlm_ast will be called, but the lock will still be considered busy until a DLM_MSG_CANCEL_REPLY message completes the cancel request. During that time, successive dlm_lock() or dlm_unlock() requests for that lock will return -EBUSY. In other words, waiting for the gdlm_ast call before issuing the next locking request is not enough. There is no way of waiting for a cancel request to actually complete, either. We rarely cancel locking requests, but when we do, we don't know when the next locking request for that lock will occur. This means that any dlm_lock() or dlm_unlock() call can potentially return -EBUSY. When that happens, this patch simply repeats the request after a short pause. This workaround could be improved upon by tracking for which dlm locks cancel requests have been issued, but that isn't strictly necessary and it would complicate the code. We haven't seen -EBUSY errors from dlm without cancel requests. Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2022-02-02 11:00:48 +01:00
GFS2: Fix recovery issues for spectators This patch fixes a couple problems dealing with spectators who remain with gfs2 mounts after the last non-spectator node fails. Before this patch, spectator mounts would try to acquire the dlm's mounted lock EX as part of its normal recovery sequence. The mounted lock is only used to determine whether the node is the first mounter, the first node to mount the file system, for the purposes of file system recovery and journal replay. It's not necessary for spectators: they should never do journal recovery. If they acquire the lock it will prevent another "real" first-mounter from acquiring the lock in EX mode, which means it also cannot do journal recovery because it doesn't think it's the first node to mount the file system. This patch checks if the mounter is a spectator, and if so, avoids grabbing the mounted lock. This allows a secondary mounter who is really the first non-spectator mounter, to do journal recovery: since the spectator doesn't acquire the lock, it can grab it in EX mode, and therefore consider itself to be the first mounter both as a "real" first mount, and as a first-real-after-spectator. Note that the control lock still needs to be taken in PR mode in order to fetch the lvb value so it has the current status of all journal's recovery. This is used as it is today by a first mounter to replay the journals. For spectators, it's merely used to fetch the status bits. All recovery is bypassed and the node waits until recovery is completed by a non-spectator node. I also improved the cryptic message given by control_mount when a spectator is waiting for a non-spectator to perform recovery. It also fixes a problem in gfs2_recover_set whereby spectators were never queueing recovery work for their own journal. They cannot do recovery themselves, but they still need to queue the work so they can check the recovery bits and clear the DFL_BLOCK_LOCKS bit once the recovery happens on another node. When the work queue runs on a spectator, it bypasses most of the work so it won't print a bunch of annoying messages. All it will print is a bunch of messages that look like this until recovery completes on the non-spectator node: GFS2: fsid=mycluster:scratch.s: recover generation 3 jid 0 GFS2: fsid=mycluster:scratch.s: recover jid 0 result busy These continue every 1.5 seconds until the recovery is done by the non-spectator, at which time it says: GFS2: fsid=mycluster:scratch.s: recover generation 4 done Then it proceeds with its mount. If the file system is mounted in spectator node and the last remaining non-spectator is fenced, any IO to the file system is blocked by dlm and the spectator waits until recovery is performed by a non-spectator. If a spectator tries to mount the file system before any non-spectators, it blocks and repeatedly gives this kernel message: GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2018-07-05 14:40:46 -05:00
GFS2: Fix recovery issues for spectators This patch fixes a couple problems dealing with spectators who remain with gfs2 mounts after the last non-spectator node fails. Before this patch, spectator mounts would try to acquire the dlm's mounted lock EX as part of its normal recovery sequence. The mounted lock is only used to determine whether the node is the first mounter, the first node to mount the file system, for the purposes of file system recovery and journal replay. It's not necessary for spectators: they should never do journal recovery. If they acquire the lock it will prevent another "real" first-mounter from acquiring the lock in EX mode, which means it also cannot do journal recovery because it doesn't think it's the first node to mount the file system. This patch checks if the mounter is a spectator, and if so, avoids grabbing the mounted lock. This allows a secondary mounter who is really the first non-spectator mounter, to do journal recovery: since the spectator doesn't acquire the lock, it can grab it in EX mode, and therefore consider itself to be the first mounter both as a "real" first mount, and as a first-real-after-spectator. Note that the control lock still needs to be taken in PR mode in order to fetch the lvb value so it has the current status of all journal's recovery. This is used as it is today by a first mounter to replay the journals. For spectators, it's merely used to fetch the status bits. All recovery is bypassed and the node waits until recovery is completed by a non-spectator node. I also improved the cryptic message given by control_mount when a spectator is waiting for a non-spectator to perform recovery. It also fixes a problem in gfs2_recover_set whereby spectators were never queueing recovery work for their own journal. They cannot do recovery themselves, but they still need to queue the work so they can check the recovery bits and clear the DFL_BLOCK_LOCKS bit once the recovery happens on another node. When the work queue runs on a spectator, it bypasses most of the work so it won't print a bunch of annoying messages. All it will print is a bunch of messages that look like this until recovery completes on the non-spectator node: GFS2: fsid=mycluster:scratch.s: recover generation 3 jid 0 GFS2: fsid=mycluster:scratch.s: recover jid 0 result busy These continue every 1.5 seconds until the recovery is done by the non-spectator, at which time it says: GFS2: fsid=mycluster:scratch.s: recover generation 4 done Then it proceeds with its mount. If the file system is mounted in spectator node and the last remaining non-spectator is fenced, any IO to the file system is blocked by dlm and the spectator waits until recovery is performed by a non-spectator. If a spectator tries to mount the file system before any non-spectators, it blocks and repeatedly gives this kernel message: GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2018-07-05 14:40:46 -05:00
GFS2: Fix recovery issues for spectators This patch fixes a couple problems dealing with spectators who remain with gfs2 mounts after the last non-spectator node fails. Before this patch, spectator mounts would try to acquire the dlm's mounted lock EX as part of its normal recovery sequence. The mounted lock is only used to determine whether the node is the first mounter, the first node to mount the file system, for the purposes of file system recovery and journal replay. It's not necessary for spectators: they should never do journal recovery. If they acquire the lock it will prevent another "real" first-mounter from acquiring the lock in EX mode, which means it also cannot do journal recovery because it doesn't think it's the first node to mount the file system. This patch checks if the mounter is a spectator, and if so, avoids grabbing the mounted lock. This allows a secondary mounter who is really the first non-spectator mounter, to do journal recovery: since the spectator doesn't acquire the lock, it can grab it in EX mode, and therefore consider itself to be the first mounter both as a "real" first mount, and as a first-real-after-spectator. Note that the control lock still needs to be taken in PR mode in order to fetch the lvb value so it has the current status of all journal's recovery. This is used as it is today by a first mounter to replay the journals. For spectators, it's merely used to fetch the status bits. All recovery is bypassed and the node waits until recovery is completed by a non-spectator node. I also improved the cryptic message given by control_mount when a spectator is waiting for a non-spectator to perform recovery. It also fixes a problem in gfs2_recover_set whereby spectators were never queueing recovery work for their own journal. They cannot do recovery themselves, but they still need to queue the work so they can check the recovery bits and clear the DFL_BLOCK_LOCKS bit once the recovery happens on another node. When the work queue runs on a spectator, it bypasses most of the work so it won't print a bunch of annoying messages. All it will print is a bunch of messages that look like this until recovery completes on the non-spectator node: GFS2: fsid=mycluster:scratch.s: recover generation 3 jid 0 GFS2: fsid=mycluster:scratch.s: recover jid 0 result busy These continue every 1.5 seconds until the recovery is done by the non-spectator, at which time it says: GFS2: fsid=mycluster:scratch.s: recover generation 4 done Then it proceeds with its mount. If the file system is mounted in spectator node and the last remaining non-spectator is fenced, any IO to the file system is blocked by dlm and the spectator waits until recovery is performed by a non-spectator. If a spectator tries to mount the file system before any non-spectators, it blocks and repeatedly gives this kernel message: GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2018-07-05 14:40:46 -05:00
GFS2: Fix recovery issues for spectators This patch fixes a couple problems dealing with spectators who remain with gfs2 mounts after the last non-spectator node fails. Before this patch, spectator mounts would try to acquire the dlm's mounted lock EX as part of its normal recovery sequence. The mounted lock is only used to determine whether the node is the first mounter, the first node to mount the file system, for the purposes of file system recovery and journal replay. It's not necessary for spectators: they should never do journal recovery. If they acquire the lock it will prevent another "real" first-mounter from acquiring the lock in EX mode, which means it also cannot do journal recovery because it doesn't think it's the first node to mount the file system. This patch checks if the mounter is a spectator, and if so, avoids grabbing the mounted lock. This allows a secondary mounter who is really the first non-spectator mounter, to do journal recovery: since the spectator doesn't acquire the lock, it can grab it in EX mode, and therefore consider itself to be the first mounter both as a "real" first mount, and as a first-real-after-spectator. Note that the control lock still needs to be taken in PR mode in order to fetch the lvb value so it has the current status of all journal's recovery. This is used as it is today by a first mounter to replay the journals. For spectators, it's merely used to fetch the status bits. All recovery is bypassed and the node waits until recovery is completed by a non-spectator node. I also improved the cryptic message given by control_mount when a spectator is waiting for a non-spectator to perform recovery. It also fixes a problem in gfs2_recover_set whereby spectators were never queueing recovery work for their own journal. They cannot do recovery themselves, but they still need to queue the work so they can check the recovery bits and clear the DFL_BLOCK_LOCKS bit once the recovery happens on another node. When the work queue runs on a spectator, it bypasses most of the work so it won't print a bunch of annoying messages. All it will print is a bunch of messages that look like this until recovery completes on the non-spectator node: GFS2: fsid=mycluster:scratch.s: recover generation 3 jid 0 GFS2: fsid=mycluster:scratch.s: recover jid 0 result busy These continue every 1.5 seconds until the recovery is done by the non-spectator, at which time it says: GFS2: fsid=mycluster:scratch.s: recover generation 4 done Then it proceeds with its mount. If the file system is mounted in spectator node and the last remaining non-spectator is fenced, any IO to the file system is blocked by dlm and the spectator waits until recovery is performed by a non-spectator. If a spectator tries to mount the file system before any non-spectators, it blocks and repeatedly gives this kernel message: GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. GFS2: fsid=mycluster:scratch: Recovery is required. Waiting for a non-spectator to mount. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
2018-07-05 14:40:46 -05:00
sched: Remove proliferation of wait_on_bit() action functions The current "wait_on_bit" interface requires an 'action' function to be provided which does the actual waiting. There are over 20 such functions, many of them identical. Most cases can be satisfied by one of just two functions, one which uses io_schedule() and one which just uses schedule(). So: Rename wait_on_bit and wait_on_bit_lock to wait_on_bit_action and wait_on_bit_lock_action to make it explicit that they need an action function. Introduce new wait_on_bit{,_lock} and wait_on_bit{,_lock}_io which are *not* given an action function but implicitly use a standard one. The decision to error-out if a signal is pending is now made based on the 'mode' argument rather than being encoded in the action function. All instances of the old wait_on_bit and wait_on_bit_lock which can use the new version have been changed accordingly and their action functions have been discarded. wait_on_bit{_lock} does not return any specific error code in the event of a signal so the caller must check for non-zero and interpolate their own error code as appropriate. The wait_on_bit() call in __fscache_wait_on_invalidate() was ambiguous as it specified TASK_UNINTERRUPTIBLE but used fscache_wait_bit_interruptible as an action function. David Howells confirms this should be uniformly "uninterruptible" The main remaining user of wait_on_bit{,_lock}_action is NFS which needs to use a freezer-aware schedule() call. A comment in fs/gfs2/glock.c notes that having multiple 'action' functions is useful as they display differently in the 'wchan' field of 'ps'. (and /proc/$PID/wchan). As the new bit_wait{,_io} functions are tagged "__sched", they will not show up at all, but something higher in the stack. So the distinction will still be visible, only with different function names (gds2_glock_wait versus gfs2_glock_dq_wait in the gfs2/glock.c case). Since first version of this patch (against 3.15) two new action functions appeared, on in NFS and one in CIFS. CIFS also now uses an action function that makes the same freezer aware schedule call as NFS. Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: David Howells <dhowells@redhat.com> (fscache, keys) Acked-by: Steven Whitehouse <swhiteho@redhat.com> (gfs2) Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Steve French <sfrench@samba.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/20140707051603.28027.72349.stgit@notabene.brown Signed-off-by: Ingo Molnar <mingo@kernel.org>
2014-07-07 15:16:04 +10:00
gfs2: Ignore dlm recovery requests if gfs2 is withdrawn When a node fails, user space informs dlm of the node failure, and dlm instructs gfs2 on the surviving nodes to perform journal recovery. It does this by calling various callback functions in lock_dlm.c. To mark its progress, it keeps generation numbers and recover bits in a dlm "control" lock lvb, which is seen by all nodes to determine which journals need to be replayed. The gfs2 on all nodes get the same recovery requests from dlm, so they all try to do the recovery, but only one will be granted the exclusive lock on the journal. The others fail with a "Busy" message on their "try lock." However, when a node is withdrawn, it cannot safely do any recovery or replay any journals. To make matters worse, gfs2 might withdraw as a result of attempting recovery. For example, this might happen if the device goes offline, or if an hba fails. But in today's gfs2 code, it doesn't check for being withdrawn at any step in the recovery process. What's worse is that these callbacks from dlm have no return code, so there is no way to indicate failure back to dlm. We can send a "Recovery failed" uevent eventually, but that tells user space what happened, not dlm's kernel code. Before this patch, lock_dlm would perform its recovery steps but ignore the result, and eventually it would still update its generation number in the lvb, despite the fact that it may have withdrawn or encountered an error. The other nodes would then see the newer generation number in the lvb and conclude that they don't need to do recovery because the generation number is newer than the last one they saw. They think a different node has already recovered the journal. This patch adds checks to several of the callbacks used by dlm in its recovery state machine so that the functions are ignored and skipped if an io error has occurred or if the file system is withdrawn. That prevents the lvb bits from being updated, and therefore dlm and user space still see the need for recovery to take place. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
2019-02-12 13:58:40 -07:00
gfs2: Ignore dlm recovery requests if gfs2 is withdrawn When a node fails, user space informs dlm of the node failure, and dlm instructs gfs2 on the surviving nodes to perform journal recovery. It does this by calling various callback functions in lock_dlm.c. To mark its progress, it keeps generation numbers and recover bits in a dlm "control" lock lvb, which is seen by all nodes to determine which journals need to be replayed. The gfs2 on all nodes get the same recovery requests from dlm, so they all try to do the recovery, but only one will be granted the exclusive lock on the journal. The others fail with a "Busy" message on their "try lock." However, when a node is withdrawn, it cannot safely do any recovery or replay any journals. To make matters worse, gfs2 might withdraw as a result of attempting recovery. For example, this might happen if the device goes offline, or if an hba fails. But in today's gfs2 code, it doesn't check for being withdrawn at any step in the recovery process. What's worse is that these callbacks from dlm have no return code, so there is no way to indicate failure back to dlm. We can send a "Recovery failed" uevent eventually, but that tells user space what happened, not dlm's kernel code. Before this patch, lock_dlm would perform its recovery steps but ignore the result, and eventually it would still update its generation number in the lvb, despite the fact that it may have withdrawn or encountered an error. The other nodes would then see the newer generation number in the lvb and conclude that they don't need to do recovery because the generation number is newer than the last one they saw. They think a different node has already recovered the journal. This patch adds checks to several of the callbacks used by dlm in its recovery state machine so that the functions are ignored and skipped if an io error has occurred or if the file system is withdrawn. That prevents the lvb bits from being updated, and therefore dlm and user space still see the need for recovery to take place. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
2019-02-12 13:58:40 -07:00
gfs2: Ignore dlm recovery requests if gfs2 is withdrawn When a node fails, user space informs dlm of the node failure, and dlm instructs gfs2 on the surviving nodes to perform journal recovery. It does this by calling various callback functions in lock_dlm.c. To mark its progress, it keeps generation numbers and recover bits in a dlm "control" lock lvb, which is seen by all nodes to determine which journals need to be replayed. The gfs2 on all nodes get the same recovery requests from dlm, so they all try to do the recovery, but only one will be granted the exclusive lock on the journal. The others fail with a "Busy" message on their "try lock." However, when a node is withdrawn, it cannot safely do any recovery or replay any journals. To make matters worse, gfs2 might withdraw as a result of attempting recovery. For example, this might happen if the device goes offline, or if an hba fails. But in today's gfs2 code, it doesn't check for being withdrawn at any step in the recovery process. What's worse is that these callbacks from dlm have no return code, so there is no way to indicate failure back to dlm. We can send a "Recovery failed" uevent eventually, but that tells user space what happened, not dlm's kernel code. Before this patch, lock_dlm would perform its recovery steps but ignore the result, and eventually it would still update its generation number in the lvb, despite the fact that it may have withdrawn or encountered an error. The other nodes would then see the newer generation number in the lvb and conclude that they don't need to do recovery because the generation number is newer than the last one they saw. They think a different node has already recovered the journal. This patch adds checks to several of the callbacks used by dlm in its recovery state machine so that the functions are ignored and skipped if an io error has occurred or if the file system is withdrawn. That prevents the lvb bits from being updated, and therefore dlm and user space still see the need for recovery to take place. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
2019-02-12 13:58:40 -07:00
gfs2: Ignore dlm recovery requests if gfs2 is withdrawn When a node fails, user space informs dlm of the node failure, and dlm instructs gfs2 on the surviving nodes to perform journal recovery. It does this by calling various callback functions in lock_dlm.c. To mark its progress, it keeps generation numbers and recover bits in a dlm "control" lock lvb, which is seen by all nodes to determine which journals need to be replayed. The gfs2 on all nodes get the same recovery requests from dlm, so they all try to do the recovery, but only one will be granted the exclusive lock on the journal. The others fail with a "Busy" message on their "try lock." However, when a node is withdrawn, it cannot safely do any recovery or replay any journals. To make matters worse, gfs2 might withdraw as a result of attempting recovery. For example, this might happen if the device goes offline, or if an hba fails. But in today's gfs2 code, it doesn't check for being withdrawn at any step in the recovery process. What's worse is that these callbacks from dlm have no return code, so there is no way to indicate failure back to dlm. We can send a "Recovery failed" uevent eventually, but that tells user space what happened, not dlm's kernel code. Before this patch, lock_dlm would perform its recovery steps but ignore the result, and eventually it would still update its generation number in the lvb, despite the fact that it may have withdrawn or encountered an error. The other nodes would then see the newer generation number in the lvb and conclude that they don't need to do recovery because the generation number is newer than the last one they saw. They think a different node has already recovered the journal. This patch adds checks to several of the callbacks used by dlm in its recovery state machine so that the functions are ignored and skipped if an io error has occurred or if the file system is withdrawn. That prevents the lvb bits from being updated, and therefore dlm and user space still see the need for recovery to take place. Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
2019-02-12 13:58:40 -07:00
workqueue: deprecate flush[_delayed]_work_sync() flush[_delayed]_work_sync() are now spurious. Mark them deprecated and convert all users to flush[_delayed]_work(). If you're cc'd and wondering what's going on: Now all workqueues are non-reentrant and the regular flushes guarantee that the work item is not pending or running on any CPU on return, so there's no reason to use the sync flushes at all and they're going away. This patch doesn't make any functional difference. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mattia Dongili <malattia@linux.it> Cc: Kent Yoder <key@linux.vnet.ibm.com> Cc: David Airlie <airlied@linux.ie> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Bryan Wu <bryan.wu@canonical.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alasdair Kergon <agk@redhat.com> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: David Woodhouse <dwmw2@infradead.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: Anton Vorontsov <cbou@mail.ru> Cc: Sangbeom Kim <sbkim73@samsung.com> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Petr Vandrovec <petr@vandrovec.name> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Avi Kivity <avi@redhat.com>
2012-08-20 14:51:24 -07:00