linux/include/linux/mtd/rawnand.h

1582 lines
48 KiB

mtd: nand: add support for Micron on-die ECC Now that the core NAND subsystem has support for on-die ECC, this commit brings the necessary code to support on-die ECC on Micron NANDs. In micron_nand_init(), we detect if the Micron NAND chip supports on-die ECC mode, by checking a number of conditions: - It must be an ONFI NAND - It must be a SLC NAND - Enabling *and* disabling on-die ECC must work - The on-die ECC must be correcting 4 bits per 512 bytes of data. Some Micron NAND chips have an on-die ECC able to correct 8 bits per 512 bytes of data, but they work slightly differently and therefore we don't support them in this patch. Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die ECC forcefully enabled), we bail out, as we don't support such NANDs. Indeed, the implementation of raw_read()/raw_write() make the assumption that on-die ECC can be disabled. Support for Micron NANDs with on-die ECC forcefully enabled can easily be added, but in the absence of such HW for testing, we preferred to simply bail out. If the on-die ECC is supported, and requested in the Device Tree, then it is indeed enabled, by using custom implementations of the ->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw() operation to properly handle the on-die ECC. In the non-raw functions, we need to enable the internal ECC engine before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization time (it asks the NAND core to let the NAND driver issue those commands). Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-04-29 11:06:45 +02:00
mtd: rawnand.h: use nested union kernel-doc markups Gets rid of those warnings and better document the parameters. ./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-07 06:35:52 -03:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: rawnand.h: use nested union kernel-doc markups Gets rid of those warnings and better document the parameters. ./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-07 06:35:52 -03:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: rawnand.h: use nested union kernel-doc markups Gets rid of those warnings and better document the parameters. ./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-07 06:35:52 -03:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: rawnand.h: use nested union kernel-doc markups Gets rid of those warnings and better document the parameters. ./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-07 06:35:52 -03:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: add datasheet's ECC information to nand_chip{} 1.) Why add the ECC information to the nand_chip{} ? Each nand chip has its requirement for the ECC correctability, such as "4bit ECC for each 512Byte" or "40bit ECC for each 1024Byte". This ECC info is very important to the nand controller, such as gpmi. Take the Micron MT29F64G08CBABA for example, its geometry is 8KiB page size, 744 bytes oob size and it requires 40bit ECC per 1KiB. If we do not provide the ECC info to the gpmi nand driver, it has to calculate the ECC correctability itself. The gpmi driver will gets the 56bit ECC for per 1KiB which is beyond its BCH's 40bit ecc capibility. The gpmi will quits in this case. But in actually, the gpmi can supports this nand chip if it can get the right ECC info. 2.) about the new fields. The @ecc_strength_ds stands for the ecc bits needed within the @ecc_step_ds. The two fields should be set from the nand chip's datasheets. For example: "4bit ECC for each 512Byte" could be: @ecc_strength_ds = 4, @ecc_step_ds = 512. "40bit ECC for each 1024Byte" could be: @ecc_strength_ds = 40, @ecc_step_ds = 1024. 3.) Why do not re-use the @strength and @size in the nand_ecc_ctrl{}? The @strength and @size in nand_ecc_ctrl{} is used by the nand controller driver, while the @ecc_strength_ds and @ecc_step_ds are get from the datasheet. Signed-off-by: Huang Shijie <b32955@freescale.com> Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-05-17 11:17:25 +08:00
mtd: add datasheet's ECC information to nand_chip{} 1.) Why add the ECC information to the nand_chip{} ? Each nand chip has its requirement for the ECC correctability, such as "4bit ECC for each 512Byte" or "40bit ECC for each 1024Byte". This ECC info is very important to the nand controller, such as gpmi. Take the Micron MT29F64G08CBABA for example, its geometry is 8KiB page size, 744 bytes oob size and it requires 40bit ECC per 1KiB. If we do not provide the ECC info to the gpmi nand driver, it has to calculate the ECC correctability itself. The gpmi driver will gets the 56bit ECC for per 1KiB which is beyond its BCH's 40bit ecc capibility. The gpmi will quits in this case. But in actually, the gpmi can supports this nand chip if it can get the right ECC info. 2.) about the new fields. The @ecc_strength_ds stands for the ecc bits needed within the @ecc_step_ds. The two fields should be set from the nand chip's datasheets. For example: "4bit ECC for each 512Byte" could be: @ecc_strength_ds = 4, @ecc_step_ds = 512. "40bit ECC for each 1024Byte" could be: @ecc_strength_ds = 40, @ecc_step_ds = 1024. 3.) Why do not re-use the @strength and @size in the nand_ecc_ctrl{}? The @strength and @size in nand_ecc_ctrl{} is used by the nand controller driver, while the @ecc_strength_ds and @ecc_step_ds are get from the datasheet. Signed-off-by: Huang Shijie <b32955@freescale.com> Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-05-17 11:17:25 +08:00
mtd: rawnand.h: use nested union kernel-doc markups Gets rid of those warnings and better document the parameters. ./include/linux/mtd/rawnand.h:752: warning: Function parameter or member 'timings.sdr' not described in 'nand_data_interface' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.in' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:817: warning: Function parameter or member 'buf.out' not described in 'nand_op_data_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.cmd' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.data' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:863: warning: Function parameter or member 'ctx.waitrdy' not described in 'nand_op_instr' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.addr' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1010: warning: Function parameter or member 'ctx.data' not described in 'nand_op_parser_pattern_elem' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.desc' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:1313: warning: Function parameter or member 'manufacturer.priv' not described in 'nand_chip' ./include/linux/mtd/rawnand.h:848: WARNING: Unexpected indentation. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-05-07 06:35:52 -03:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: add datasheet's ECC information to nand_chip{} 1.) Why add the ECC information to the nand_chip{} ? Each nand chip has its requirement for the ECC correctability, such as "4bit ECC for each 512Byte" or "40bit ECC for each 1024Byte". This ECC info is very important to the nand controller, such as gpmi. Take the Micron MT29F64G08CBABA for example, its geometry is 8KiB page size, 744 bytes oob size and it requires 40bit ECC per 1KiB. If we do not provide the ECC info to the gpmi nand driver, it has to calculate the ECC correctability itself. The gpmi driver will gets the 56bit ECC for per 1KiB which is beyond its BCH's 40bit ecc capibility. The gpmi will quits in this case. But in actually, the gpmi can supports this nand chip if it can get the right ECC info. 2.) about the new fields. The @ecc_strength_ds stands for the ecc bits needed within the @ecc_step_ds. The two fields should be set from the nand chip's datasheets. For example: "4bit ECC for each 512Byte" could be: @ecc_strength_ds = 4, @ecc_step_ds = 512. "40bit ECC for each 1024Byte" could be: @ecc_strength_ds = 40, @ecc_step_ds = 1024. 3.) Why do not re-use the @strength and @size in the nand_ecc_ctrl{}? The @strength and @size in nand_ecc_ctrl{} is used by the nand controller driver, while the @ecc_strength_ds and @ecc_step_ds are get from the datasheet. Signed-off-by: Huang Shijie <b32955@freescale.com> Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-05-17 11:17:25 +08:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00
mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-09 14:16:45 +01:00