2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:21:01 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:21:05 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-06-17 11:48:11 -04:00
|
|
|
|
2008-04-29 18:13:32 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-06-17 11:48:11 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-10-27 21:30:15 -04:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-10-27 21:30:14 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-10-27 21:30:15 -04:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2009-01-05 22:18:16 -05:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-05 21:49:55 -05:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
|
|
|
|
|
ext4: fix initialization of UNINIT bitmap blocks
This fixes a bug which caused on-line resizing of filesystems with a
1k blocksize to fail. The root cause of this bug was the fact that if
an uninitalized bitmap block gets read in by userspace (which
e2fsprogs does try to avoid, but can happen when the blocksize is less
than the pagesize and an adjacent blocks is read into memory)
ext4_read_block_bitmap() was erroneously depending on the buffer
uptodate flag to decide whether it needed to initialize the bitmap
block in memory --- i.e., to set the standard set of blocks in use by
a block group (superblock, bitmaps, inode table, etc.). Essentially,
ext4_read_block_bitmap() assumed it was the only routine that might
try to read a block containing a block bitmap, which is simply not
true.
To fix this, ext4_read_block_bitmap() and ext4_read_inode_bitmap()
must always initialize uninitialized bitmap blocks. Once a block or
inode is allocated out of that bitmap, it will be marked as
initialized in the block group descriptor, so in general this won't
result any extra unnecessary work.
Signed-off-by: Frederic Bohe <frederic.bohe@bull.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2008-10-10 08:09:18 -04:00
|
|
|
|
2009-01-05 21:49:55 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2009-01-05 21:49:55 -05:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
2009-01-05 21:49:55 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
|
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2009-01-05 22:18:16 -05:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-03-04 18:38:18 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2008-09-08 23:00:52 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 23:00:52 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 23:00:52 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2009-06-17 11:48:11 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-03-03 09:05:07 -05:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2010-03-03 09:05:01 -05:00
|
|
|
|
2010-03-03 09:05:05 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-06-07 13:16:22 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
|
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
|
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:31:53 -05:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-06-11 23:14:04 -04:00
|
|
|
|
2010-05-16 07:00:00 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
|
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-25 11:50:39 -04:00
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-10-27 21:30:14 -04:00
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
2009-03-04 19:31:53 -05:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2009-03-04 19:31:53 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2009-03-04 19:31:53 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-04-21 22:45:55 +00:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2009-06-13 11:09:42 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
2009-06-13 11:09:42 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:21:05 -07:00
|
|
|
|
2006-10-11 01:21:19 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
2010-05-16 22:00:00 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-06-13 11:09:42 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2009-04-22 21:00:36 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-04-22 21:00:36 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-06-13 11:09:42 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-04 19:31:53 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-03-23 21:32:00 -04:00
|
|
|
|
2009-03-04 19:31:53 -05:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-06-13 11:09:42 -04:00
|
|
|
|
2009-06-13 11:45:35 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
|
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
|
|
|
|
|
2009-03-12 12:20:01 -04:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2009-06-17 11:48:11 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
|
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2009-06-13 11:45:35 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-07-05 23:45:11 -04:00
|
|
|
|
2009-06-13 11:45:35 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2009-02-21 12:13:24 -05:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2009-04-14 07:37:40 -04:00
|
|
|
|
2009-03-12 12:20:01 -04:00
|
|
|
|
2009-02-21 12:13:24 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-04-14 07:37:40 -04:00
|
|
|
|
2009-02-21 12:13:24 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-06-13 11:09:42 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-06-13 11:45:35 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2009-01-07 00:06:22 -05:00
|
|
|
|
|
|
|
|
|
2010-02-16 15:06:29 -05:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2008-11-07 09:21:01 -05:00
|
|
|
|
|
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
2009-05-02 20:35:09 -04:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2009-01-07 00:06:22 -05:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
|
|
|
|
|
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
We need to make sure we update the inode bitmap and clear
EXT4_BG_INODE_UNINIT flag with sb_bgl_lock held, since
ext4_read_inode_bitmap() looks at EXT4_BG_INODE_UNINIT to decide
whether to initialize the inode bitmap each time it is called.
(introduced by commit c806e68f.)
ext4_read_inode_bitmap does:
spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
ext4_init_inode_bitmap(sb, bh, block_group, desc);
and ext4_new_inode does
if (!ext4_set_bit_atomic(sb_bgl_lock(sbi, group),
ino, inode_bitmap_bh->b_data))
......
...
spin_lock(sb_bgl_lock(sbi, group));
gdp->bg_flags &= cpu_to_le16(~EXT4_BG_INODE_UNINIT);
i.e., on allocation we update the bitmap then we take the sb_bgl_lock
and clear the EXT4_BG_INODE_UNINIT flag. What can happen is a
parallel ext4_read_inode_bitmap can zero out the bitmap in between
the above ext4_set_bit_atomic and spin_lock(sb_bg_lock..)
The race results in below user visible errors
EXT4-fs error (device sdb1): ext4_free_inode: bit already cleared for inode 168449
EXT4-fs warning (device sdb1): ext4_unlink: Deleting nonexistent file ...
EXT4-fs warning (device sdb1): ext4_rmdir: empty directory has too many links ...
# ls -al /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71
ls: /mnt/tmp/f/p369/d3/d6/d39/db2/dee/d10f/d3f/l71: Stale NFS file handle
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
2009-01-05 21:38:14 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-06-11 23:14:04 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
2009-03-04 19:09:10 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
2010-03-04 17:31:51 +03:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2010-03-04 17:31:51 +03:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
Ext4: Uninitialized Block Groups
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked,
regardless of whether it is in use. This is this the most time consuming part
of the filesystem check. The unintialized block group feature can greatly
reduce e2fsck time by eliminating checking of uninitialized inodes.
With this feature, there is a a high water mark of used inodes for each block
group. Block and inode bitmaps can be uninitialized on disk via a flag in the
group descriptor to avoid reading or scanning them at e2fsck time. A checksum
of each group descriptor is used to ensure that corruption in the group
descriptor's bit flags does not cause incorrect operation.
The feature is enabled through a mkfs option
mke2fs /dev/ -O uninit_groups
A patch adding support for uninitialized block groups to e2fsprogs tools has
been posted to the linux-ext4 mailing list.
The patches have been stress tested with fsstress and fsx. In performance
tests testing e2fsck time, we have seen that e2fsck time on ext3 grows
linearly with the total number of inodes in the filesytem. In ext4 with the
uninitialized block groups feature, the e2fsck time is constant, based
solely on the number of used inodes rather than the total inode count.
Since typical ext4 filesystems only use 1-10% of their inodes, this feature can
greatly reduce e2fsck time for users. With performance improvement of 2-20
times, depending on how full the filesystem is.
The attached graph shows the major improvements in e2fsck times in filesystems
with a large total inode count, but few inodes in use.
In each group descriptor if we have
EXT4_BG_INODE_UNINIT set in bg_flags:
Inode table is not initialized/used in this group. So we can skip
the consistency check during fsck.
EXT4_BG_BLOCK_UNINIT set in bg_flags:
No block in the group is used. So we can skip the block bitmap
verification for this group.
We also add two new fields to group descriptor as a part of
uninitialized group patch.
__le16 bg_itable_unused; /* Unused inodes count */
__le16 bg_checksum; /* crc16(sb_uuid+group+desc) */
bg_itable_unused:
If we have EXT4_BG_INODE_UNINIT not set in bg_flags
then bg_itable_unused will give the offset within
the inode table till the inodes are used. This can be
used by fsck to skip list of inodes that are marked unused.
bg_checksum:
Now that we depend on bg_flags and bg_itable_unused to determine
the block and inode usage, we need to make sure group descriptor
is not corrupt. We add checksum to group descriptor to
detect corruption. If the descriptor is found to be corrupt, we
mark all the blocks and inodes in the group used.
Signed-off-by: Avantika Mathur <mathur@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
2007-10-16 18:38:25 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2007-07-18 09:15:20 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-25 16:38:03 -05:00
|
|
|
|
2009-02-15 18:09:20 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-25 16:38:03 -05:00
|
|
|
|
2009-02-15 18:09:20 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-12 12:18:34 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-01-07 00:06:22 -05:00
|
|
|
|
2008-12-30 02:03:31 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-01-24 14:34:07 -05:00
|
|
|
|
|
|
|
|
|
2007-07-18 09:15:20 -04:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2010-03-03 09:05:07 -05:00
|
|
|
|
2010-03-03 09:05:01 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-06 14:53:16 -05:00
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2008-04-29 08:11:12 -04:00
|
|
|
|
2010-05-16 22:00:00 -04:00
|
|
|
|
2008-02-25 16:38:03 -05:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:21:03 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-04-29 22:00:36 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-06-17 11:48:11 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-03-03 09:05:01 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2010-03-03 09:05:05 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2008-12-30 02:03:31 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-01-03 22:33:39 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
|
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-15 14:19:27 -05:00
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-11 19:27:31 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-07 00:15:37 -08:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2008-08-02 21:21:02 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:53 -07:00
|
|
|
|
2008-01-28 23:58:27 -05:00
|
|
|
|
2009-07-27 21:44:40 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 23:00:52 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
2009-05-01 08:50:38 -04:00
|
|
|
|
2008-09-08 22:25:24 -04:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
2009-01-05 22:20:24 -05:00
|
|
|
|
2006-10-11 01:20:50 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-10-27 21:30:05 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-10-27 23:44:47 -04:00
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
|
|
|
|
|
2010-10-27 23:44:47 -04:00
|
|
|
|
|
|
|
|
|
ext4: add support for lazy inode table initialization
When the lazy_itable_init extended option is passed to mke2fs, it
considerably speeds up filesystem creation because inode tables are
not zeroed out. The fact that parts of the inode table are
uninitialized is not a problem so long as the block group descriptors,
which contain information regarding how much of the inode table has
been initialized, has not been corrupted However, if the block group
checksums are not valid, e2fsck must scan the entire inode table, and
the the old, uninitialized data could potentially cause e2fsck to
report false problems.
Hence, it is important for the inode tables to be initialized as soon
as possble. This commit adds this feature so that mke2fs can safely
use the lazy inode table initialization feature to speed up formatting
file systems.
This is done via a new new kernel thread called ext4lazyinit, which is
created on demand and destroyed, when it is no longer needed. There
is only one thread for all ext4 filesystems in the system. When the
first filesystem with inititable mount option is mounted, ext4lazyinit
thread is created, then the filesystem can register its request in the
request list.
This thread then walks through the list of requests picking up
scheduled requests and invoking ext4_init_inode_table(). Next schedule
time for the request is computed by multiplying the time it took to
zero out last inode table with wait multiplier, which can be set with
the (init_itable=n) mount option (default is 10). We are doing
this so we do not take the whole I/O bandwidth. When the thread is no
longer necessary (request list is empty) it frees the appropriate
structures and exits (and can be created later later by another
filesystem).
We do not disturb regular inode allocations in any way, it just do not
care whether the inode table is, or is not zeroed. But when zeroing, we
have to skip used inodes, obviously. Also we should prevent new inode
allocations from the group, while zeroing is on the way. For that we
take write alloc_sem lock in ext4_init_inode_table() and read alloc_sem
in the ext4_claim_inode, so when we are unlucky and allocator hits the
group which is currently being zeroed, it just has to wait.
This can be suppresed using the mount option no_init_itable.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2010-10-27 21:30:05 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
