linux/net/tipc/node.c

2227 lines
54 KiB

tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
2017-01-24 13:00:43 +01:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
2017-01-24 13:00:43 +01:00
2017-01-24 13:00:43 +01:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: use message to abort connections when losing contact to node In the current implementation, each 'struct tipc_node' instance keeps a linked list of those ports/sockets that are connected to the node represented by that struct. The purpose of this is to let the node object know which sockets to alert when it loses contact with its peer node, i.e., which sockets need to have their connections aborted. This entails an unwanted direct reference from the node structure back to the port/socket structure, and a need to grab port_lock when we have to make an upcall to the port. We want to get rid of this unecessary BH entry point into the socket, and also eliminate its use of port_lock. In this commit, we instead let the node struct keep list of "connected socket" structs, which each represents a connected socket, but is allocated independently by the node at the moment of connection. If the node loses contact with its peer node, the list is traversed, and a "connection abort" message is created for each entry in the list. The message is sent to it respective connected socket using the ordinary data path, and the receiving socket aborts its connections upon reception of the message. This enables us to get rid of the direct reference from 'struct node' to ´struct port', and another unwanted BH access point to the latter. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-22 18:09:08 -04:00
tipc: delay ESTABLISH state event when link is established Link establishing, just like link teardown, is a non-atomic action, in the sense that discovering that conditions are right to establish a link, and the actual adding of the link to one of the node's send slots is done in two different lock contexts. The link FSM is designed to help bridging the gap between the two contexts in a safe manner. We have now discovered a weakness in the implementaton of this FSM. Because we directly let the link go from state LINK_ESTABLISHING to state LINK_ESTABLISHED already in the first lock context, we are unable to distinguish between a fully established link, i.e., a link that has been added to its slot, and a link that has not yet reached the second lock context. It may hence happen that a manual intervention, e.g., when disabling an interface, causes the function tipc_node_link_down() to try removing the link from the node slots, decrementing its active link counter etc, although the link was never added there in the first place. We solve this by delaying the actual state change until we reach the second lock context, inside the function tipc_node_link_up(). This makes it possible for potentail callers of __tipc_node_link_down() to know if they should proceed or not, and the problem is solved. Unforunately, the situation described above also has a second problem. Since there by necessity is a tipc_node_link_up() call pending once the node lock has been released, we must defuse that call by setting the link back from LINK_ESTABLISHING to LINK_RESET state. This forces us to make a slight modification to the link FSM, which will now look as follows. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | +----------------+ | | | RESET_EVT| |RESET_EVT | | | | | | | | | | |ESTABLISH_EVT | | | | +-------------+ | | | | | | RESET_EVT | | | | | | | | | | | V V V | | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15 14:52:44 -04:00
tipc: merge link->exec_mode and link->state into one FSM Until now, we have been handling link failover and synchronization by using an additional link state variable, "exec_mode". This variable is not independent of the link FSM state, something causing a risk of inconsistencies, apart from the fact that it clutters the code. The conditions are now in place to define a new link FSM that covers all existing use cases, including failover and synchronization, and eliminate the "exec_mode" field altogether. The FSM must also support non-atomic resetting of links, which will be introduced later. The new link FSM is shown below, with 7 states and 8 events. Only events leading to state change are shown as edges. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | | | | | | +--------------+ | | | RESET_EVT| |RESET_EVT |ESTABLISH_EVT | | | | | | | | | | | | V V | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ These changes are fully backwards compatible. Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:21 -04:00
tipc: merge link->exec_mode and link->state into one FSM Until now, we have been handling link failover and synchronization by using an additional link state variable, "exec_mode". This variable is not independent of the link FSM state, something causing a risk of inconsistencies, apart from the fact that it clutters the code. The conditions are now in place to define a new link FSM that covers all existing use cases, including failover and synchronization, and eliminate the "exec_mode" field altogether. The FSM must also support non-atomic resetting of links, which will be introduced later. The new link FSM is shown below, with 7 states and 8 events. Only events leading to state change are shown as edges. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | | | | | | +--------------+ | | | RESET_EVT| |RESET_EVT |ESTABLISH_EVT | | | | | | | | | | | | V V | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ These changes are fully backwards compatible. Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:21 -04:00
tipc: delay ESTABLISH state event when link is established Link establishing, just like link teardown, is a non-atomic action, in the sense that discovering that conditions are right to establish a link, and the actual adding of the link to one of the node's send slots is done in two different lock contexts. The link FSM is designed to help bridging the gap between the two contexts in a safe manner. We have now discovered a weakness in the implementaton of this FSM. Because we directly let the link go from state LINK_ESTABLISHING to state LINK_ESTABLISHED already in the first lock context, we are unable to distinguish between a fully established link, i.e., a link that has been added to its slot, and a link that has not yet reached the second lock context. It may hence happen that a manual intervention, e.g., when disabling an interface, causes the function tipc_node_link_down() to try removing the link from the node slots, decrementing its active link counter etc, although the link was never added there in the first place. We solve this by delaying the actual state change until we reach the second lock context, inside the function tipc_node_link_up(). This makes it possible for potentail callers of __tipc_node_link_down() to know if they should proceed or not, and the problem is solved. Unforunately, the situation described above also has a second problem. Since there by necessity is a tipc_node_link_up() call pending once the node lock has been released, we must defuse that call by setting the link back from LINK_ESTABLISHING to LINK_RESET state. This forces us to make a slight modification to the link FSM, which will now look as follows. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | +----------------+ | | | RESET_EVT| |RESET_EVT | | | | | | | | | | |ESTABLISH_EVT | | | | +-------------+ | | | | | | RESET_EVT | | | | | | | | | | | V V V | | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15 14:52:44 -04:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: delay ESTABLISH state event when link is established Link establishing, just like link teardown, is a non-atomic action, in the sense that discovering that conditions are right to establish a link, and the actual adding of the link to one of the node's send slots is done in two different lock contexts. The link FSM is designed to help bridging the gap between the two contexts in a safe manner. We have now discovered a weakness in the implementaton of this FSM. Because we directly let the link go from state LINK_ESTABLISHING to state LINK_ESTABLISHED already in the first lock context, we are unable to distinguish between a fully established link, i.e., a link that has been added to its slot, and a link that has not yet reached the second lock context. It may hence happen that a manual intervention, e.g., when disabling an interface, causes the function tipc_node_link_down() to try removing the link from the node slots, decrementing its active link counter etc, although the link was never added there in the first place. We solve this by delaying the actual state change until we reach the second lock context, inside the function tipc_node_link_up(). This makes it possible for potentail callers of __tipc_node_link_down() to know if they should proceed or not, and the problem is solved. Unforunately, the situation described above also has a second problem. Since there by necessity is a tipc_node_link_up() call pending once the node lock has been released, we must defuse that call by setting the link back from LINK_ESTABLISHING to LINK_RESET state. This forces us to make a slight modification to the link FSM, which will now look as follows. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | +----------------+ | | | RESET_EVT| |RESET_EVT | | | | | | | | | | |ESTABLISH_EVT | | | | +-------------+ | | | | | | RESET_EVT | | | | | | | | | | | V V V | | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15 14:52:44 -04:00
tipc: delay ESTABLISH state event when link is established Link establishing, just like link teardown, is a non-atomic action, in the sense that discovering that conditions are right to establish a link, and the actual adding of the link to one of the node's send slots is done in two different lock contexts. The link FSM is designed to help bridging the gap between the two contexts in a safe manner. We have now discovered a weakness in the implementaton of this FSM. Because we directly let the link go from state LINK_ESTABLISHING to state LINK_ESTABLISHED already in the first lock context, we are unable to distinguish between a fully established link, i.e., a link that has been added to its slot, and a link that has not yet reached the second lock context. It may hence happen that a manual intervention, e.g., when disabling an interface, causes the function tipc_node_link_down() to try removing the link from the node slots, decrementing its active link counter etc, although the link was never added there in the first place. We solve this by delaying the actual state change until we reach the second lock context, inside the function tipc_node_link_up(). This makes it possible for potentail callers of __tipc_node_link_down() to know if they should proceed or not, and the problem is solved. Unforunately, the situation described above also has a second problem. Since there by necessity is a tipc_node_link_up() call pending once the node lock has been released, we must defuse that call by setting the link back from LINK_ESTABLISHING to LINK_RESET state. This forces us to make a slight modification to the link FSM, which will now look as follows. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | +----------------+ | | | RESET_EVT| |RESET_EVT | | | | | | | | | | |ESTABLISH_EVT | | | | +-------------+ | | | | | | RESET_EVT | | | | | | | | | | | V V V | | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15 14:52:44 -04:00
tipc: add neighbor monitoring framework TIPC based clusters are by default set up with full-mesh link connectivity between all nodes. Those links are expected to provide a short failure detection time, by default set to 1500 ms. Because of this, the background load for neighbor monitoring in an N-node cluster increases with a factor N on each node, while the overall monitoring traffic through the network infrastructure increases at a ~(N * (N - 1)) rate. Experience has shown that such clusters don't scale well beyond ~100 nodes unless we significantly increase failure discovery tolerance. This commit introduces a framework and an algorithm that drastically reduces this background load, while basically maintaining the original failure detection times across the whole cluster. Using this algorithm, background load will now grow at a rate of ~(2 * sqrt(N)) per node, and at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will now have to actively monitor 38 neighbors in a 400-node cluster, instead of as before 399. This "Overlapping Ring Supervision Algorithm" is completely distributed and employs no centralized or coordinated state. It goes as follows: - Each node makes up a linearly ascending, circular list of all its N known neighbors, based on their TIPC node identity. This algorithm must be the same on all nodes. - The node then selects the next M = sqrt(N) - 1 nodes downstream from itself in the list, and chooses to actively monitor those. This is called its "local monitoring domain". - It creates a domain record describing the monitoring domain, and piggy-backs this in the data area of all neighbor monitoring messages (LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in the cluster eventually (default within 400 ms) will learn about its monitoring domain. - Whenever a node discovers a change in its local domain, e.g., a node has been added or has gone down, it creates and sends out a new version of its node record to inform all neighbors about the change. - A node receiving a domain record from anybody outside its local domain matches this against its own list (which may not look the same), and chooses to not actively monitor those members of the received domain record that are also present in its own list. Instead, it relies on indications from the direct monitoring nodes if an indirectly monitored node has gone up or down. If a node is indicated lost, the receiving node temporarily activates its own direct monitoring towards that node in order to confirm, or not, that it is actually gone. - Since each node is actively monitoring sqrt(N) downstream neighbors, each node is also actively monitored by the same number of upstream neighbors. This means that all non-direct monitoring nodes normally will receive sqrt(N) indications that a node is gone. - A major drawback with ring monitoring is how it handles failures that cause massive network partitionings. If both a lost node and all its direct monitoring neighbors are inside the lost partition, the nodes in the remaining partition will never receive indications about the loss. To overcome this, each node also chooses to actively monitor some nodes outside its local domain. Those nodes are called remote domain "heads", and are selected in such a way that no node in the cluster will be more than two direct monitoring hops away. Because of this, each node, apart from monitoring the member of its local domain, will also typically monitor sqrt(N) remote head nodes. - As an optimization, local list status, domain status and domain records are marked with a generation number. This saves senders from unnecessarily conveying unaltered domain records, and receivers from performing unneeded re-adaptations of their node monitoring list, such as re-assigning domain heads. - As a measure of caution we have added the possibility to disable the new algorithm through configuration. We do this by keeping a threshold value for the cluster size; a cluster that grows beyond this value will switch from full-mesh to ring monitoring, and vice versa when it shrinks below the value. This means that if the threshold is set to a value larger than any anticipated cluster size (default size is 32) the new algorithm is effectively disabled. A patch set for altering the threshold value and for listing the table contents will follow shortly. - This change is fully backwards compatible. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-13 20:46:22 -04:00
tipc: eliminate risk of premature link setup during failover When a link goes down, and there is still a working link towards its destination node, a failover is initiated, and the failed link is not allowed to re-establish until that procedure is finished. To ensure this, the concerned link endpoints are set to state LINK_FAILINGOVER, and the node endpoints to NODE_FAILINGOVER during the failover period. However, if the link reset is due to a disabled bearer, the corres- ponding link endpoint is deleted, and only the node endpoint knows about the ongoing failover. Now, if the disabled bearer is re-enabled during the failover period, the discovery mechanism may create a new link endpoint that is ready to be established, despite that this is not permitted. This situation may cause both the ongoing failover and any subsequent link synchronization to fail. In this commit, we ensure that a newly created link goes directly to state LINK_FAILINGOVER if the corresponding node state is NODE_FAILINGOVER. This eliminates the problem described above. Furthermore, we tighten the criteria for which packets are allowed to end a failover state in the function tipc_node_check_state(). By checking that the receiving link is up and running, instead of just checking that it is not in failover mode, we eliminate the risk that protocol packets from the re-created link may cause the failover to be prematurely terminated. Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-20 02:12:54 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: correct error in node fsm commit 88e8ac7000dc ("tipc: reduce transmission rate of reset messages when link is down") revealed a flaw in the node FSM, as defined in the log of commit 66996b6c47ed ("tipc: extend node FSM"). We see the following scenario: 1: Node B receives a RESET message from node A before its link endpoint is fully up, i.e., the node FSM is in state SELF_UP_PEER_COMING. This event will not change the node FSM state, but the (distinct) link FSM will move to state RESETTING. 2: As an effect of the previous event, the local endpoint on B will declare node A lost, and post the event SELF_DOWN to the its node FSM. This moves the FSM state to SELF_DOWN_PEER_LEAVING, meaning that no messages will be accepted from A until it receives another RESET message that confirms that A's endpoint has been reset. This is wasteful, since we know this as a fact already from the first received RESET, but worse is that the link instance's FSM has not wasted this information, but instead moved on to state ESTABLISHING, meaning that it repeatedly sends out ACTIVATE messages to the reset peer A. 3: Node A will receive one of the ACTIVATE messages, move its link FSM to state ESTABLISHED, and start repeatedly sending out STATE messages to node B. 4: Node B will consistently drop these messages, since it can only accept accept a RESET according to its node FSM. 5: After four lost STATE messages node A will reset its link and start repeatedly sending out RESET messages to B. 6: Because of the reduced send rate for RESET messages, it is very likely that A will receive an ACTIVATE (which is sent out at a much higher frequency) before it gets the chance to send a RESET, and A may hence quickly move back to state ESTABLISHED and continue sending out STATE messages, which will again be dropped by B. 7: GOTO 5. 8: After having repeated the cycle 5-7 a number of times, node A will by chance get in between with sending a RESET, and the situation is resolved. Unfortunately, we have seen that it may take a substantial amount of time before this vicious loop is broken, sometimes in the order of minutes. We correct this by making a small correction to the node FSM: When a node in state SELF_UP_PEER_COMING receives a SELF_DOWN event, it now moves directly back to state SELF_DOWN_PEER_DOWN, instead of as now SELF_DOWN_PEER_LEAVING. This is logically consistent, since we don't need to wait for RESET confirmation from of an endpoint that we alread know has been reset. It also means that node B in the scenario above will not be dropping incoming STATE messages, and the link can come up immediately. Finally, a symmetry comparison reveals that the FSM has a similar error when receiving the event PEER_DOWN in state PEER_UP_SELF_COMING. Instead of moving to PERR_DOWN_SELF_LEAVING, it should move directly to SELF_DOWN_PEER_DOWN. Although we have never seen any negative effect of this logical error, we choose fix this one, too. The node FSM looks as follows after those changes: +----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |-----------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_ |FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +-------->| SELF_UP_ |<-------+ | | | | +-----------------| PEER_UP |----------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING| |PEER_COMING| |SELF_COMING| |SELF_LEAVING| +------------+ +-----------+ +-----------+ +------------+ | | A A | | | | | | | | | SELF_ | |SELF_ |PEER_ |PEER_ | | DOWN_EVT| |UP_EVT |UP_EVT |DOWN_EVT | | | | | | | | | | | | | | | +--------------+ | | |PEER_DOWN_EVT +--->| SELF_DOWN_ |<---+ SELF_DOWN_EVT| +------------------->| PEER_DOWN |<--------------------+ +--------------+ Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-08 12:00:04 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: delay ESTABLISH state event when link is established Link establishing, just like link teardown, is a non-atomic action, in the sense that discovering that conditions are right to establish a link, and the actual adding of the link to one of the node's send slots is done in two different lock contexts. The link FSM is designed to help bridging the gap between the two contexts in a safe manner. We have now discovered a weakness in the implementaton of this FSM. Because we directly let the link go from state LINK_ESTABLISHING to state LINK_ESTABLISHED already in the first lock context, we are unable to distinguish between a fully established link, i.e., a link that has been added to its slot, and a link that has not yet reached the second lock context. It may hence happen that a manual intervention, e.g., when disabling an interface, causes the function tipc_node_link_down() to try removing the link from the node slots, decrementing its active link counter etc, although the link was never added there in the first place. We solve this by delaying the actual state change until we reach the second lock context, inside the function tipc_node_link_up(). This makes it possible for potentail callers of __tipc_node_link_down() to know if they should proceed or not, and the problem is solved. Unforunately, the situation described above also has a second problem. Since there by necessity is a tipc_node_link_up() call pending once the node lock has been released, we must defuse that call by setting the link back from LINK_ESTABLISHING to LINK_RESET state. This forces us to make a slight modification to the link FSM, which will now look as follows. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | +----------------+ | | | RESET_EVT| |RESET_EVT | | | | | | | | | | |ESTABLISH_EVT | | | | +-------------+ | | | | | | RESET_EVT | | | | | | | | | | | V V V | | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-15 14:52:44 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: correct error in node fsm commit 88e8ac7000dc ("tipc: reduce transmission rate of reset messages when link is down") revealed a flaw in the node FSM, as defined in the log of commit 66996b6c47ed ("tipc: extend node FSM"). We see the following scenario: 1: Node B receives a RESET message from node A before its link endpoint is fully up, i.e., the node FSM is in state SELF_UP_PEER_COMING. This event will not change the node FSM state, but the (distinct) link FSM will move to state RESETTING. 2: As an effect of the previous event, the local endpoint on B will declare node A lost, and post the event SELF_DOWN to the its node FSM. This moves the FSM state to SELF_DOWN_PEER_LEAVING, meaning that no messages will be accepted from A until it receives another RESET message that confirms that A's endpoint has been reset. This is wasteful, since we know this as a fact already from the first received RESET, but worse is that the link instance's FSM has not wasted this information, but instead moved on to state ESTABLISHING, meaning that it repeatedly sends out ACTIVATE messages to the reset peer A. 3: Node A will receive one of the ACTIVATE messages, move its link FSM to state ESTABLISHED, and start repeatedly sending out STATE messages to node B. 4: Node B will consistently drop these messages, since it can only accept accept a RESET according to its node FSM. 5: After four lost STATE messages node A will reset its link and start repeatedly sending out RESET messages to B. 6: Because of the reduced send rate for RESET messages, it is very likely that A will receive an ACTIVATE (which is sent out at a much higher frequency) before it gets the chance to send a RESET, and A may hence quickly move back to state ESTABLISHED and continue sending out STATE messages, which will again be dropped by B. 7: GOTO 5. 8: After having repeated the cycle 5-7 a number of times, node A will by chance get in between with sending a RESET, and the situation is resolved. Unfortunately, we have seen that it may take a substantial amount of time before this vicious loop is broken, sometimes in the order of minutes. We correct this by making a small correction to the node FSM: When a node in state SELF_UP_PEER_COMING receives a SELF_DOWN event, it now moves directly back to state SELF_DOWN_PEER_DOWN, instead of as now SELF_DOWN_PEER_LEAVING. This is logically consistent, since we don't need to wait for RESET confirmation from of an endpoint that we alread know has been reset. It also means that node B in the scenario above will not be dropping incoming STATE messages, and the link can come up immediately. Finally, a symmetry comparison reveals that the FSM has a similar error when receiving the event PEER_DOWN in state PEER_UP_SELF_COMING. Instead of moving to PERR_DOWN_SELF_LEAVING, it should move directly to SELF_DOWN_PEER_DOWN. Although we have never seen any negative effect of this logical error, we choose fix this one, too. The node FSM looks as follows after those changes: +----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |-----------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_ |FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +-------->| SELF_UP_ |<-------+ | | | | +-----------------| PEER_UP |----------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING| |PEER_COMING| |SELF_COMING| |SELF_LEAVING| +------------+ +-----------+ +-----------+ +------------+ | | A A | | | | | | | | | SELF_ | |SELF_ |PEER_ |PEER_ | | DOWN_EVT| |UP_EVT |UP_EVT |DOWN_EVT | | | | | | | | | | | | | | | +--------------+ | | |PEER_DOWN_EVT +--->| SELF_DOWN_ |<---+ SELF_DOWN_EVT| +------------------->| PEER_DOWN |<--------------------+ +--------------+ Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-08 12:00:04 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: extend node FSM In the next commit, we will move link synch/failover orchestration to the link aggregation level. In order to do this, we first need to extend the node FSM with two more states, NODE_SYNCHING and NODE_FAILINGOVER, plus four new events to enter and leave those states. This commit introduces this change, without yet making use of it. The node FSM now looks as follows: +-----------------------------------------+ | PEER_DOWN_EVT| | | +------------------------+----------------+ | |SELF_DOWN_EVT | | | | | | | | +-----------+ +-----------+ | | |NODE_ | |NODE_ | | | +----------|FAILINGOVER|<---------|SYNCHING |------------+ | | |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | | | |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| | | | | | | | | | | | | | | | | | | | |FAILOVER_|FAILOVER_ |SYNCH_ |SYNCH_ | | | | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | | | | | | | | | | | | | | | | | | | | | +--------------+ | | | | | +------->| SELF_UP_ |<-------+ | | | | +----------------| PEER_UP |------------------+ | | | | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | | | | | A A | | | | | | | | | | | | | | PEER_UP_EVT| |SELF_UP_EVT | | | | | | | | | | | V V V | | V V V +------------+ +-----------+ +-----------+ +------------+ |SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN | |PEER_LEAVING|<------|PEER_COMING| |SELF_COMING|------>|SELF_LEAVING| +------------+ SELF_ +-----------+ +-----------+ PEER_ +------------+ | DOWN_EVT A A DOWN_EVT | | | | | | | | | | SELF_UP_EVT| |PEER_UP_EVT | | | | | | | | | |PEER_DOWN_EVT +--------------+ SELF_DOWN_EVT| +------------------->| SELF_DOWN_ |<--------------------+ | PEER_DOWN | +--------------+ Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:18 -04:00
tipc: introduce node contact FSM The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-16 16:54:30 -04:00
tipc: reduce risk of user starvation during link congestion The socket code currently handles link congestion by either blocking and trying to send again when the congestion has abated, or just returning to the user with -EAGAIN and let him re-try later. This mechanism is prone to starvation, because the wakeup algorithm is non-atomic. During the time the link issues a wakeup signal, until the socket wakes up and re-attempts sending, other senders may have come in between and occupied the free buffer space in the link. This in turn may lead to a socket having to make many send attempts before it is successful. In extremely loaded systems we have observed latency times of several seconds before a low-priority socket is able to send out a message. In this commit, we simplify this mechanism and reduce the risk of the described scenario happening. When a message is attempted sent via a congested link, we now let it be added to the link's backlog queue anyway, thus permitting an oversubscription of one message per source socket. We still create a wakeup item and return an error code, hence instructing the sender to block or stop sending. Only when enough space has been freed up in the link's backlog queue do we issue a wakeup event that allows the sender to continue with the next message, if any. The fact that a socket now can consider a message sent even when the link returns a congestion code means that the sending socket code can be simplified. Also, since this is a good opportunity to get rid of the obsolete 'mtu change' condition in the three socket send functions, we now choose to refactor those functions completely. Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-03 10:55:11 -05:00
tipc: reduce risk of user starvation during link congestion The socket code currently handles link congestion by either blocking and trying to send again when the congestion has abated, or just returning to the user with -EAGAIN and let him re-try later. This mechanism is prone to starvation, because the wakeup algorithm is non-atomic. During the time the link issues a wakeup signal, until the socket wakes up and re-attempts sending, other senders may have come in between and occupied the free buffer space in the link. This in turn may lead to a socket having to make many send attempts before it is successful. In extremely loaded systems we have observed latency times of several seconds before a low-priority socket is able to send out a message. In this commit, we simplify this mechanism and reduce the risk of the described scenario happening. When a message is attempted sent via a congested link, we now let it be added to the link's backlog queue anyway, thus permitting an oversubscription of one message per source socket. We still create a wakeup item and return an error code, hence instructing the sender to block or stop sending. Only when enough space has been freed up in the link's backlog queue do we issue a wakeup event that allows the sender to continue with the next message, if any. The fact that a socket now can consider a message sent even when the link returns a congestion code means that the sending socket code can be simplified. Also, since this is a good opportunity to get rid of the obsolete 'mtu change' condition in the three socket send functions, we now choose to refactor those functions completely. Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-03 10:55:11 -05:00
tipc: reduce risk of user starvation during link congestion The socket code currently handles link congestion by either blocking and trying to send again when the congestion has abated, or just returning to the user with -EAGAIN and let him re-try later. This mechanism is prone to starvation, because the wakeup algorithm is non-atomic. During the time the link issues a wakeup signal, until the socket wakes up and re-attempts sending, other senders may have come in between and occupied the free buffer space in the link. This in turn may lead to a socket having to make many send attempts before it is successful. In extremely loaded systems we have observed latency times of several seconds before a low-priority socket is able to send out a message. In this commit, we simplify this mechanism and reduce the risk of the described scenario happening. When a message is attempted sent via a congested link, we now let it be added to the link's backlog queue anyway, thus permitting an oversubscription of one message per source socket. We still create a wakeup item and return an error code, hence instructing the sender to block or stop sending. Only when enough space has been freed up in the link's backlog queue do we issue a wakeup event that allows the sender to continue with the next message, if any. The fact that a socket now can consider a message sent even when the link returns a congestion code means that the sending socket code can be simplified. Also, since this is a good opportunity to get rid of the obsolete 'mtu change' condition in the three socket send functions, we now choose to refactor those functions completely. Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-03 10:55:11 -05:00
tipc: reduce risk of user starvation during link congestion The socket code currently handles link congestion by either blocking and trying to send again when the congestion has abated, or just returning to the user with -EAGAIN and let him re-try later. This mechanism is prone to starvation, because the wakeup algorithm is non-atomic. During the time the link issues a wakeup signal, until the socket wakes up and re-attempts sending, other senders may have come in between and occupied the free buffer space in the link. This in turn may lead to a socket having to make many send attempts before it is successful. In extremely loaded systems we have observed latency times of several seconds before a low-priority socket is able to send out a message. In this commit, we simplify this mechanism and reduce the risk of the described scenario happening. When a message is attempted sent via a congested link, we now let it be added to the link's backlog queue anyway, thus permitting an oversubscription of one message per source socket. We still create a wakeup item and return an error code, hence instructing the sender to block or stop sending. Only when enough space has been freed up in the link's backlog queue do we issue a wakeup event that allows the sender to continue with the next message, if any. The fact that a socket now can consider a message sent even when the link returns a congestion code means that the sending socket code can be simplified. Also, since this is a good opportunity to get rid of the obsolete 'mtu change' condition in the three socket send functions, we now choose to refactor those functions completely. Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-03 10:55:11 -05:00
tipc: merge link->exec_mode and link->state into one FSM Until now, we have been handling link failover and synchronization by using an additional link state variable, "exec_mode". This variable is not independent of the link FSM state, something causing a risk of inconsistencies, apart from the fact that it clutters the code. The conditions are now in place to define a new link FSM that covers all existing use cases, including failover and synchronization, and eliminate the "exec_mode" field altogether. The FSM must also support non-atomic resetting of links, which will be introduced later. The new link FSM is shown below, with 7 states and 8 events. Only events leading to state change are shown as edges. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | | | | | | +--------------+ | | | RESET_EVT| |RESET_EVT |ESTABLISH_EVT | | | | | | | | | | | | V V | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ These changes are fully backwards compatible. Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:21 -04:00
tipc: fix stale link problem during synchronization Recent changes to the link synchronization means that we can now just drop packets arriving on the synchronizing link before the synch point is reached. This has lead to significant simplifications to the implementation, but also turns out to have a flip side that we need to consider. Under unlucky circumstances, the two endpoints may end up repeatedly dropping each other's packets, while immediately asking for retransmission of the same packets, just to drop them once more. This pattern will eventually be broken when the synch point is reached on the other link, but before that, the endpoints may have arrived at the retransmission limit (stale counter) that indicates that the link should be broken. We see this happen at rare occasions. The fix for this is to not ask for retransmissions when a link is in state LINK_SYNCHING. The fact that the link has reached this state means that it has already received the first SYNCH packet, and that it knows the synch point. Hence, it doesn't need any more packets until the other link has reached the synch point, whereafter it can go ahead and ask for the missing packets. However, because of the reduced traffic on the synching link that follows this change, it may now take longer to discover that the synch point has been reached. We compensate for this by letting all packets, on any of the links, trig a check for synchronization termination. This is possible because the packets themselves don't contain any information that is needed for discovering this condition. Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-20 02:12:56 -04:00
2015-11-19 14:30:41 -05:00
tipc: eliminate risk of stalled link synchronization In commit 6e498158a827 ("tipc: move link synch and failover to link aggregation level") we introduced a new mechanism for performing link failover and synchronization. We have now detected a bug in this mechanism. During link synchronization we use the arrival of any packet on the tunnel link to trig a check for whether it has reached the synchronization point or not. This has turned out to be too permissive, since it may cause an arriving non-last SYNCH packet to end the synch state, just to see the next SYNCH packet initiate a new synch state with a new, higher synch point. This is not fatal, but should be avoided, because it may significantly extend the synchronization period, while at the same time we are not allowed to send NACKs if packets are lost. In the worst case, a low-traffic user may see its traffic stall until a LINK_PROTOCOL state message trigs the link to leave synchronization state. At the same time, LINK_PROTOCOL packets which happen to have a (non- valid) sequence number lower than the tunnel link's rcv_nxt value will be consistently dropped, and will never be able to resolve the situation described above. We fix this by exempting LINK_PROTOCOL packets from the sequence number check, as they should be. We also reduce (but don't completely eliminate) the risk of entering multiple synchronization states by only allowing the (logically) first SYNCH packet to initiate a synchronization state. This works independently of actual packet arrival order. Fixes: commit 6e498158a827 ("tipc: move link synch and failover to link aggregation level") Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-13 12:41:51 -04:00
tipc: eliminate risk of premature link setup during failover When a link goes down, and there is still a working link towards its destination node, a failover is initiated, and the failed link is not allowed to re-establish until that procedure is finished. To ensure this, the concerned link endpoints are set to state LINK_FAILINGOVER, and the node endpoints to NODE_FAILINGOVER during the failover period. However, if the link reset is due to a disabled bearer, the corres- ponding link endpoint is deleted, and only the node endpoint knows about the ongoing failover. Now, if the disabled bearer is re-enabled during the failover period, the discovery mechanism may create a new link endpoint that is ready to be established, despite that this is not permitted. This situation may cause both the ongoing failover and any subsequent link synchronization to fail. In this commit, we ensure that a newly created link goes directly to state LINK_FAILINGOVER if the corresponding node state is NODE_FAILINGOVER. This eliminates the problem described above. Furthermore, we tighten the criteria for which packets are allowed to end a failover state in the function tipc_node_check_state(). By checking that the receiving link is up and running, instead of just checking that it is not in failover mode, we eliminate the risk that protocol packets from the re-created link may cause the failover to be prematurely terminated. Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-20 02:12:54 -04:00
tipc: merge link->exec_mode and link->state into one FSM Until now, we have been handling link failover and synchronization by using an additional link state variable, "exec_mode". This variable is not independent of the link FSM state, something causing a risk of inconsistencies, apart from the fact that it clutters the code. The conditions are now in place to define a new link FSM that covers all existing use cases, including failover and synchronization, and eliminate the "exec_mode" field altogether. The FSM must also support non-atomic resetting of links, which will be introduced later. The new link FSM is shown below, with 7 states and 8 events. Only events leading to state change are shown as edges. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | | | | | | +--------------+ | | | RESET_EVT| |RESET_EVT |ESTABLISH_EVT | | | | | | | | | | | | V V | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ These changes are fully backwards compatible. Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:21 -04:00
tipc: merge link->exec_mode and link->state into one FSM Until now, we have been handling link failover and synchronization by using an additional link state variable, "exec_mode". This variable is not independent of the link FSM state, something causing a risk of inconsistencies, apart from the fact that it clutters the code. The conditions are now in place to define a new link FSM that covers all existing use cases, including failover and synchronization, and eliminate the "exec_mode" field altogether. The FSM must also support non-atomic resetting of links, which will be introduced later. The new link FSM is shown below, with 7 states and 8 events. Only events leading to state change are shown as edges. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | | | | | | +--------------+ | | | RESET_EVT| |RESET_EVT |ESTABLISH_EVT | | | | | | | | | | | | V V | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ These changes are fully backwards compatible. Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:21 -04:00
tipc: eliminate risk of stalled link synchronization In commit 6e498158a827 ("tipc: move link synch and failover to link aggregation level") we introduced a new mechanism for performing link failover and synchronization. We have now detected a bug in this mechanism. During link synchronization we use the arrival of any packet on the tunnel link to trig a check for whether it has reached the synchronization point or not. This has turned out to be too permissive, since it may cause an arriving non-last SYNCH packet to end the synch state, just to see the next SYNCH packet initiate a new synch state with a new, higher synch point. This is not fatal, but should be avoided, because it may significantly extend the synchronization period, while at the same time we are not allowed to send NACKs if packets are lost. In the worst case, a low-traffic user may see its traffic stall until a LINK_PROTOCOL state message trigs the link to leave synchronization state. At the same time, LINK_PROTOCOL packets which happen to have a (non- valid) sequence number lower than the tunnel link's rcv_nxt value will be consistently dropped, and will never be able to resolve the situation described above. We fix this by exempting LINK_PROTOCOL packets from the sequence number check, as they should be. We also reduce (but don't completely eliminate) the risk of entering multiple synchronization states by only allowing the (logically) first SYNCH packet to initiate a synchronization state. This works independently of actual packet arrival order. Fixes: commit 6e498158a827 ("tipc: move link synch and failover to link aggregation level") Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-13 12:41:51 -04:00
tipc: remove premature ESTABLISH FSM event at link synchronization When a link between two nodes come up, both endpoints will initially send out a STATE message to the peer, to increase the probability that the peer endpoint also is up when the first traffic message arrives. Thereafter, if the establishing link is the second link between two nodes, this first "traffic" message is a TUNNEL_PROTOCOL/SYNCH message, helping the peer to perform initial synchronization between the two links. However, the initial STATE message may be lost, in which case the SYNCH message will be the first one arriving at the peer. This should also work, as the SYNCH message itself will be used to take up the link endpoint before initializing synchronization. Unfortunately the code for this case is broken. Currently, the link is brought up through a tipc_link_fsm_evt(ESTABLISHED) when a SYNCH arrives, whereupon __tipc_node_link_up() is called to distribute the link slots and take the link into traffic. But, __tipc_node_link_up() is itself starting with a test for whether the link is up, and if true, returns without action. Clearly, the tipc_link_fsm_evt(ESTABLISHED) call is unnecessary, since tipc_node_link_up() is itself issuing such an event, but also harmful, since it inhibits tipc_node_link_up() to perform the test of its tasks, and the link endpoint in question hence is never taken into traffic. This problem has been exposed when we set up dual links between pre- and post-4.4 kernels, because the former ones don't send out the initial STATE message described above. We fix this by removing the unnecessary event call. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-08 22:23:56 +02:00
tipc: merge link->exec_mode and link->state into one FSM Until now, we have been handling link failover and synchronization by using an additional link state variable, "exec_mode". This variable is not independent of the link FSM state, something causing a risk of inconsistencies, apart from the fact that it clutters the code. The conditions are now in place to define a new link FSM that covers all existing use cases, including failover and synchronization, and eliminate the "exec_mode" field altogether. The FSM must also support non-atomic resetting of links, which will be introduced later. The new link FSM is shown below, with 7 states and 8 events. Only events leading to state change are shown as edges. +------------------------------------+ |RESET_EVT | | | | +--------------+ | +-----------------| SYNCHING |-----------------+ | |FAILURE_EVT +--------------+ PEER_RESET_EVT| | | A | | | | | | | | | | | | | | |SYNCH_ |SYNCH_ | | | |BEGIN_EVT |END_EVT | | | | | | | V | V V | +-------------+ +--------------+ +------------+ | | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET | | +-------------+ FAILURE_ +--------------+ PEER_ +------------+ | | EVT | A RESET_EVT | | | | | | | | | | | | | +--------------+ | | | RESET_EVT| |RESET_EVT |ESTABLISH_EVT | | | | | | | | | | | | V V | | | +-------------+ +--------------+ RESET_EVT| +--->| RESET |--------->| ESTABLISHING |<----------------+ +-------------+ PEER_ +--------------+ | A RESET_EVT | | | | | | | |FAILOVER_ |FAILOVER_ |FAILOVER_ |BEGIN_EVT |END_EVT |BEGIN_EVT | | | V | | +-------------+ | | FAILINGOVER |<----------------+ +-------------+ These changes are fully backwards compatible. Tested-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 18:24:21 -04:00
2015-11-19 14:30:41 -05:00
tipc: fix stale link problem during synchronization Recent changes to the link synchronization means that we can now just drop packets arriving on the synchronizing link before the synch point is reached. This has lead to significant simplifications to the implementation, but also turns out to have a flip side that we need to consider. Under unlucky circumstances, the two endpoints may end up repeatedly dropping each other's packets, while immediately asking for retransmission of the same packets, just to drop them once more. This pattern will eventually be broken when the synch point is reached on the other link, but before that, the endpoints may have arrived at the retransmission limit (stale counter) that indicates that the link should be broken. We see this happen at rare occasions. The fix for this is to not ask for retransmissions when a link is in state LINK_SYNCHING. The fact that the link has reached this state means that it has already received the first SYNCH packet, and that it knows the synch point. Hence, it doesn't need any more packets until the other link has reached the synch point, whereafter it can go ahead and ask for the missing packets. However, because of the reduced traffic on the synching link that follows this change, it may now take longer to discover that the synch point has been reached. We compensate for this by letting all packets, on any of the links, trig a check for synchronization termination. This is possible because the packets themselves don't contain any information that is needed for discovering this condition. Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-20 02:12:56 -04:00
tipc: fix stale link problem during synchronization Recent changes to the link synchronization means that we can now just drop packets arriving on the synchronizing link before the synch point is reached. This has lead to significant simplifications to the implementation, but also turns out to have a flip side that we need to consider. Under unlucky circumstances, the two endpoints may end up repeatedly dropping each other's packets, while immediately asking for retransmission of the same packets, just to drop them once more. This pattern will eventually be broken when the synch point is reached on the other link, but before that, the endpoints may have arrived at the retransmission limit (stale counter) that indicates that the link should be broken. We see this happen at rare occasions. The fix for this is to not ask for retransmissions when a link is in state LINK_SYNCHING. The fact that the link has reached this state means that it has already received the first SYNCH packet, and that it knows the synch point. Hence, it doesn't need any more packets until the other link has reached the synch point, whereafter it can go ahead and ask for the missing packets. However, because of the reduced traffic on the synching link that follows this change, it may now take longer to discover that the synch point has been reached. We compensate for this by letting all packets, on any of the links, trig a check for synchronization termination. This is possible because the packets themselves don't contain any information that is needed for discovering this condition. Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-20 02:12:56 -04:00
tipc: fix stale link problem during synchronization Recent changes to the link synchronization means that we can now just drop packets arriving on the synchronizing link before the synch point is reached. This has lead to significant simplifications to the implementation, but also turns out to have a flip side that we need to consider. Under unlucky circumstances, the two endpoints may end up repeatedly dropping each other's packets, while immediately asking for retransmission of the same packets, just to drop them once more. This pattern will eventually be broken when the synch point is reached on the other link, but before that, the endpoints may have arrived at the retransmission limit (stale counter) that indicates that the link should be broken. We see this happen at rare occasions. The fix for this is to not ask for retransmissions when a link is in state LINK_SYNCHING. The fact that the link has reached this state means that it has already received the first SYNCH packet, and that it knows the synch point. Hence, it doesn't need any more packets until the other link has reached the synch point, whereafter it can go ahead and ask for the missing packets. However, because of the reduced traffic on the synching link that follows this change, it may now take longer to discover that the synch point has been reached. We compensate for this by letting all packets, on any of the links, trig a check for synchronization termination. This is possible because the packets themselves don't contain any information that is needed for discovering this condition. Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-20 02:12:56 -04:00
tipc: only process unicast on intended node We have observed complete lock up of broadcast-link transmission due to unacknowledged packets never being removed from the 'transmq' queue. This is traced to nodes having their ack field set beyond the sequence number of packets that have actually been transmitted to them. Consider an example where node 1 has sent 10 packets to node 2 on a link and node 3 has sent 20 packets to node 2 on another link. We see examples of an ack from node 2 destined for node 3 being treated as an ack from node 2 at node 1. This leads to the ack on the node 1 to node 2 link being increased to 20 even though we have only sent 10 packets. When node 1 does get around to sending further packets, none of the packets with sequence numbers less than 21 are actually removed from the transmq. To resolve this we reinstate some code lost in commit d999297c3dbb ("tipc: reduce locking scope during packet reception") which ensures that only messages destined for the receiving node are processed by that node. This prevents the sequence numbers from getting out of sync and resolves the packet leakage, thereby resolving the broadcast-link transmission lock-ups we observed. While we are aware that this change only patches over a root problem that we still haven't identified, this is a sanity test that it is always legitimate to do. It will remain in the code even after we identify and fix the real problem. Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: John Thompson <john.thompson@alliedtelesis.co.nz> Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-29 10:40:24 -04:00
tipc: only process unicast on intended node We have observed complete lock up of broadcast-link transmission due to unacknowledged packets never being removed from the 'transmq' queue. This is traced to nodes having their ack field set beyond the sequence number of packets that have actually been transmitted to them. Consider an example where node 1 has sent 10 packets to node 2 on a link and node 3 has sent 20 packets to node 2 on another link. We see examples of an ack from node 2 destined for node 3 being treated as an ack from node 2 at node 1. This leads to the ack on the node 1 to node 2 link being increased to 20 even though we have only sent 10 packets. When node 1 does get around to sending further packets, none of the packets with sequence numbers less than 21 are actually removed from the transmq. To resolve this we reinstate some code lost in commit d999297c3dbb ("tipc: reduce locking scope during packet reception") which ensures that only messages destined for the receiving node are processed by that node. This prevents the sequence numbers from getting out of sync and resolves the packet leakage, thereby resolving the broadcast-link transmission lock-ups we observed. While we are aware that this change only patches over a root problem that we still haven't identified, this is a sanity test that it is always legitimate to do. It will remain in the code even after we identify and fix the real problem. Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: John Thompson <john.thompson@alliedtelesis.co.nz> Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-29 10:40:24 -04:00
tipc: fix broadcast link synchronization problem In commit 2d18ac4ba745 ("tipc: extend broadcast link initialization criteria") we tried to fix a problem with the initial synchronization of broadcast link acknowledge values. Unfortunately that solution is not sufficient to solve the issue. We have seen it happen that LINK_PROTOCOL/STATE packets with a valid non-zero unicast acknowledge number may bypass BCAST_PROTOCOL initialization, NAME_DISTRIBUTOR and other STATE packets with invalid broadcast acknowledge numbers, leading to premature opening of the broadcast link. When the bypassed packets finally arrive, they are inadvertently accepted, and the already correctly initialized acknowledge number in the broadcast receive link is overwritten by the invalid (zero) value of the said packets. After this the broadcast link goes stale. We now fix this by marking the packets where we know the acknowledge value is or may be invalid, and then ignoring the acks from those. To this purpose, we claim an unused bit in the header to indicate that the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR packets, plus those LINK_PROTOCOL packets sent out before the broadcast links are fully synchronized. This minor protocol update is fully backwards compatible. Reported-by: John Thompson <thompa.atl@gmail.com> Tested-by: John Thompson <thompa.atl@gmail.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-27 18:51:55 -04:00
netlink: pass extended ACK struct where available This is an add-on to the previous patch that passes the extended ACK structure where it's already available by existing genl_info or extack function arguments. This was done with this spatch (with some manual adjustment of indentation): @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, info->extack) ... } @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, info->extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse(A, B, C, D, E, NULL) +nla_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ... } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_validate(A, B, C, D, NULL) +nlmsg_validate(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate(A, B, C, D, NULL) +nla_validate(A, B, C, D, extack) ...> } @@ expression A, B, C; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate_nested(A, B, C, NULL) +nla_validate_nested(A, B, C, extack) ...> } Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-12 14:34:08 +02:00
netlink: pass extended ACK struct where available This is an add-on to the previous patch that passes the extended ACK structure where it's already available by existing genl_info or extack function arguments. This was done with this spatch (with some manual adjustment of indentation): @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, info->extack) ... } @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, info->extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse(A, B, C, D, E, NULL) +nla_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ... } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_validate(A, B, C, D, NULL) +nlmsg_validate(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate(A, B, C, D, NULL) +nla_validate(A, B, C, D, extack) ...> } @@ expression A, B, C; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate_nested(A, B, C, NULL) +nla_validate_nested(A, B, C, extack) ...> } Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-12 14:34:08 +02:00
netlink: pass extended ACK struct where available This is an add-on to the previous patch that passes the extended ACK structure where it's already available by existing genl_info or extack function arguments. This was done with this spatch (with some manual adjustment of indentation): @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, info->extack) ... } @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, info->extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse(A, B, C, D, E, NULL) +nla_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ... } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_validate(A, B, C, D, NULL) +nlmsg_validate(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate(A, B, C, D, NULL) +nla_validate(A, B, C, D, extack) ...> } @@ expression A, B, C; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate_nested(A, B, C, NULL) +nla_validate_nested(A, B, C, extack) ...> } Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-12 14:34:08 +02:00
netlink: pass extended ACK struct where available This is an add-on to the previous patch that passes the extended ACK structure where it's already available by existing genl_info or extack function arguments. This was done with this spatch (with some manual adjustment of indentation): @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, info->extack) ... } @@ expression A, B, C, D, E; identifier fn, info; @@ fn(..., struct genl_info *info, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, info->extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse(A, B, C, D, E, NULL) +nla_parse(A, B, C, D, E, extack) ...> } @@ expression A, B, C, D, E; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { ... -nlmsg_parse(A, B, C, D, E, NULL) +nlmsg_parse(A, B, C, D, E, extack) ... } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_parse_nested(A, B, C, D, NULL) +nla_parse_nested(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nlmsg_validate(A, B, C, D, NULL) +nlmsg_validate(A, B, C, D, extack) ...> } @@ expression A, B, C, D; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate(A, B, C, D, NULL) +nla_validate(A, B, C, D, extack) ...> } @@ expression A, B, C; identifier fn, extack; @@ fn(..., struct netlink_ext_ack *extack, ...) { <... -nla_validate_nested(A, B, C, NULL) +nla_validate_nested(A, B, C, extack) ...> } Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-12 14:34:08 +02:00