kernel/linux
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-11-13 07:31:07 +00:00
Code Issues Releases Packages Activity
linux/drivers/clocksource/jcore-pit.c

258 lines
6.7 KiB
Raw Normal View History

clocksource/drivers/jcore: Convert to SPDX identifier The licensing text references explicitely the COPYING file in the kernel base directory, which is clearly GPL version 2 only. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Rich Felker <dalias@libc.org> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20220510171254.467236056@linutronix.de Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2022-05-10 19:24:38 +02:00
clocksource: Add J-Core timer/clocksource driver At the hardware level, the J-Core PIT is integrated with the interrupt controller, but it is represented as its own device and has an independent programming interface. It provides a 12-bit countdown timer, which is not presently used, and a periodic timer. The interval length for the latter is programmable via a 32-bit throttle register whose units are determined by a bus-period register. The periodic timer is used to implement both periodic and oneshot clock event modes; in oneshot mode the interrupt handler simply disables the timer as soon as it fires. Despite its device tree node representing an interrupt for the PIT, the actual irq generated is programmable, not hard-wired. The driver is responsible for programming the PIT to generate the hardware irq number that the DT assigns to it. On SMP configurations, J-Core provides cpu-local instances of the PIT; no broadcast timer is needed. This driver supports the creation of the necessary per-cpu clock_event_device instances. A nanosecond-resolution clocksource is provided using the J-Core "RTC" registers, which give a 64-bit seconds count and 32-bit nanoseconds that wrap every second. The driver converts these to a full-range 32-bit nanoseconds count. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-10-13 21:51:06 +00:00
clocksource: Use a plain u64 instead of cycle_t There is no point in having an extra type for extra confusion. u64 is unambiguous. Conversion was done with the following coccinelle script: @rem@ @@ -typedef u64 cycle_t; @fix@ typedef cycle_t; @@ -cycle_t +u64 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>
2016-12-21 20:32:01 +01:00
clocksource: Add J-Core timer/clocksource driver At the hardware level, the J-Core PIT is integrated with the interrupt controller, but it is represented as its own device and has an independent programming interface. It provides a 12-bit countdown timer, which is not presently used, and a periodic timer. The interval length for the latter is programmable via a 32-bit throttle register whose units are determined by a bus-period register. The periodic timer is used to implement both periodic and oneshot clock event modes; in oneshot mode the interrupt handler simply disables the timer as soon as it fires. Despite its device tree node representing an interrupt for the PIT, the actual irq generated is programmable, not hard-wired. The driver is responsible for programming the PIT to generate the hardware irq number that the DT assigns to it. On SMP configurations, J-Core provides cpu-local instances of the PIT; no broadcast timer is needed. This driver supports the creation of the necessary per-cpu clock_event_device instances. A nanosecond-resolution clocksource is provided using the J-Core "RTC" registers, which give a 64-bit seconds count and 32-bit nanoseconds that wrap every second. The driver converts these to a full-range 32-bit nanoseconds count. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-10-13 21:51:06 +00:00
irqchip/jcore-aic, clocksource/drivers/jcore: Fix jcore-pit interrupt request The jcore-aic irqchip does not have separate interrupt numbers reserved for cpu-local vs global interrupts. Therefore the device drivers need to request the given interrupt as per CPU interrupt. 69a9dcbd2d65 ("clocksource/drivers/jcore: Use request_percpu_irq()") converted the clocksource driver over to request_percpu_irq(), but failed to do add all the required changes, resulting in a failure to register PIT interrupts. Fix this by: 1) Explicitly mark the interrupt via irq_set_percpu_devid() in jcore_pit_init(). 2) Enable and disable the per CPU interrupt in the CPU hotplug callbacks. 3) Pass the correct per-cpu cookie to the irq handler by using handle_percpu_devid_irq() instead of handle_percpu_irq() in handle_jcore_irq(). [ tglx: Massage change log ] Fixes: 69a9dcbd2d65 ("clocksource/drivers/jcore: Use request_percpu_irq()") Signed-off-by: Artur Rojek <contact@artur-rojek.eu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Uros Bizjak <ubizjak@gmail.com> Link: https://lore.kernel.org/all/20250216175545.35079-3-contact@artur-rojek.eu
2025-02-16 18:55:45 +01:00
clocksource: Add J-Core timer/clocksource driver At the hardware level, the J-Core PIT is integrated with the interrupt controller, but it is represented as its own device and has an independent programming interface. It provides a 12-bit countdown timer, which is not presently used, and a periodic timer. The interval length for the latter is programmable via a 32-bit throttle register whose units are determined by a bus-period register. The periodic timer is used to implement both periodic and oneshot clock event modes; in oneshot mode the interrupt handler simply disables the timer as soon as it fires. Despite its device tree node representing an interrupt for the PIT, the actual irq generated is programmable, not hard-wired. The driver is responsible for programming the PIT to generate the hardware irq number that the DT assigns to it. On SMP configurations, J-Core provides cpu-local instances of the PIT; no broadcast timer is needed. This driver supports the creation of the necessary per-cpu clock_event_device instances. A nanosecond-resolution clocksource is provided using the J-Core "RTC" registers, which give a 64-bit seconds count and 32-bit nanoseconds that wrap every second. The driver converts these to a full-range 32-bit nanoseconds count. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-10-13 21:51:06 +00:00
clocksource/drivers/jcore: Use request_percpu_irq() Use request_percpu_irq() instead of request_irq() to solve the following sparse warning: jcore-pit.c:173:40: warning: incorrect type in argument 5 (different address spaces) jcore-pit.c:173:40: expected void *dev jcore-pit.c:173:40: got struct jcore_pit [noderef] __percpu *static [assigned] [toplevel] jcore_pit_percpu Compile tested only. Signed-off-by: Uros Bizjak <ubizjak@gmail.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rich Felker <dalias@libc.org> Link: https://lore.kernel.org/r/20240902104810.21080-1-ubizjak@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2024-09-02 12:48:04 +02:00
clocksource: Add J-Core timer/clocksource driver At the hardware level, the J-Core PIT is integrated with the interrupt controller, but it is represented as its own device and has an independent programming interface. It provides a 12-bit countdown timer, which is not presently used, and a periodic timer. The interval length for the latter is programmable via a 32-bit throttle register whose units are determined by a bus-period register. The periodic timer is used to implement both periodic and oneshot clock event modes; in oneshot mode the interrupt handler simply disables the timer as soon as it fires. Despite its device tree node representing an interrupt for the PIT, the actual irq generated is programmable, not hard-wired. The driver is responsible for programming the PIT to generate the hardware irq number that the DT assigns to it. On SMP configurations, J-Core provides cpu-local instances of the PIT; no broadcast timer is needed. This driver supports the creation of the necessary per-cpu clock_event_device instances. A nanosecond-resolution clocksource is provided using the J-Core "RTC" registers, which give a 64-bit seconds count and 32-bit nanoseconds that wrap every second. The driver converts these to a full-range 32-bit nanoseconds count. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-10-13 21:51:06 +00:00
irqchip/jcore-aic, clocksource/drivers/jcore: Fix jcore-pit interrupt request The jcore-aic irqchip does not have separate interrupt numbers reserved for cpu-local vs global interrupts. Therefore the device drivers need to request the given interrupt as per CPU interrupt. 69a9dcbd2d65 ("clocksource/drivers/jcore: Use request_percpu_irq()") converted the clocksource driver over to request_percpu_irq(), but failed to do add all the required changes, resulting in a failure to register PIT interrupts. Fix this by: 1) Explicitly mark the interrupt via irq_set_percpu_devid() in jcore_pit_init(). 2) Enable and disable the per CPU interrupt in the CPU hotplug callbacks. 3) Pass the correct per-cpu cookie to the irq handler by using handle_percpu_devid_irq() instead of handle_percpu_irq() in handle_jcore_irq(). [ tglx: Massage change log ] Fixes: 69a9dcbd2d65 ("clocksource/drivers/jcore: Use request_percpu_irq()") Signed-off-by: Artur Rojek <contact@artur-rojek.eu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Uros Bizjak <ubizjak@gmail.com> Link: https://lore.kernel.org/all/20250216175545.35079-3-contact@artur-rojek.eu
2025-02-16 18:55:45 +01:00
clocksource/drivers/jcore: Use request_percpu_irq() Use request_percpu_irq() instead of request_irq() to solve the following sparse warning: jcore-pit.c:173:40: warning: incorrect type in argument 5 (different address spaces) jcore-pit.c:173:40: expected void *dev jcore-pit.c:173:40: got struct jcore_pit [noderef] __percpu *static [assigned] [toplevel] jcore_pit_percpu Compile tested only. Signed-off-by: Uros Bizjak <ubizjak@gmail.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rich Felker <dalias@libc.org> Link: https://lore.kernel.org/r/20240902104810.21080-1-ubizjak@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2024-09-02 12:48:04 +02:00
clocksource: Add J-Core timer/clocksource driver At the hardware level, the J-Core PIT is integrated with the interrupt controller, but it is represented as its own device and has an independent programming interface. It provides a 12-bit countdown timer, which is not presently used, and a periodic timer. The interval length for the latter is programmable via a 32-bit throttle register whose units are determined by a bus-period register. The periodic timer is used to implement both periodic and oneshot clock event modes; in oneshot mode the interrupt handler simply disables the timer as soon as it fires. Despite its device tree node representing an interrupt for the PIT, the actual irq generated is programmable, not hard-wired. The driver is responsible for programming the PIT to generate the hardware irq number that the DT assigns to it. On SMP configurations, J-Core provides cpu-local instances of the PIT; no broadcast timer is needed. This driver supports the creation of the necessary per-cpu clock_event_device instances. A nanosecond-resolution clocksource is provided using the J-Core "RTC" registers, which give a 64-bit seconds count and 32-bit nanoseconds that wrap every second. The driver converts these to a full-range 32-bit nanoseconds count. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-10-13 21:51:06 +00:00
cpu/hotplug: Cleanup state names When the state names got added a script was used to add the extra argument to the calls. The script basically converted the state constant to a string, but the cleanup to convert these strings into meaningful ones did not happen. Replace all the useless strings with 'subsys/xxx/yyy:state' strings which are used in all the other places already. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-12-21 20:19:54 +01:00
irqchip/jcore-aic, clocksource/drivers/jcore: Fix jcore-pit interrupt request The jcore-aic irqchip does not have separate interrupt numbers reserved for cpu-local vs global interrupts. Therefore the device drivers need to request the given interrupt as per CPU interrupt. 69a9dcbd2d65 ("clocksource/drivers/jcore: Use request_percpu_irq()") converted the clocksource driver over to request_percpu_irq(), but failed to do add all the required changes, resulting in a failure to register PIT interrupts. Fix this by: 1) Explicitly mark the interrupt via irq_set_percpu_devid() in jcore_pit_init(). 2) Enable and disable the per CPU interrupt in the CPU hotplug callbacks. 3) Pass the correct per-cpu cookie to the irq handler by using handle_percpu_devid_irq() instead of handle_percpu_irq() in handle_jcore_irq(). [ tglx: Massage change log ] Fixes: 69a9dcbd2d65 ("clocksource/drivers/jcore: Use request_percpu_irq()") Signed-off-by: Artur Rojek <contact@artur-rojek.eu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Uros Bizjak <ubizjak@gmail.com> Link: https://lore.kernel.org/all/20250216175545.35079-3-contact@artur-rojek.eu
2025-02-16 18:55:45 +01:00
clocksource: Add J-Core timer/clocksource driver At the hardware level, the J-Core PIT is integrated with the interrupt controller, but it is represented as its own device and has an independent programming interface. It provides a 12-bit countdown timer, which is not presently used, and a periodic timer. The interval length for the latter is programmable via a 32-bit throttle register whose units are determined by a bus-period register. The periodic timer is used to implement both periodic and oneshot clock event modes; in oneshot mode the interrupt handler simply disables the timer as soon as it fires. Despite its device tree node representing an interrupt for the PIT, the actual irq generated is programmable, not hard-wired. The driver is responsible for programming the PIT to generate the hardware irq number that the DT assigns to it. On SMP configurations, J-Core provides cpu-local instances of the PIT; no broadcast timer is needed. This driver supports the creation of the necessary per-cpu clock_event_device instances. A nanosecond-resolution clocksource is provided using the J-Core "RTC" registers, which give a 64-bit seconds count and 32-bit nanoseconds that wrap every second. The driver converts these to a full-range 32-bit nanoseconds count. Signed-off-by: Rich Felker <dalias@libc.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Cc: linux-sh@vger.kernel.org Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-10-13 21:51:06 +00:00
clocksource/drivers: Rename CLOCKSOURCE_OF_DECLARE to TIMER_OF_DECLARE The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the clocksource at early stage. However, this macro is also used to initialize the clockevent if any, or the clockevent only. It was originally suggested to declare another macro to initialize a clockevent, so in order to separate the two entities even they belong to the same IP. This was not accepted because of the impact on the DT where splitting a clocksource/clockevent definition does not make sense as it is a Linux concept not a hardware description. On the other side, the clocksource has not interrupt declared while the clockevent has, so it is easy from the driver to know if the description is for a clockevent or a clocksource, IOW it could be implemented at the driver level. So instead of dealing with a named clocksource macro, let's use a more generic one: TIMER_OF_DECLARE. The patch has not functional changes. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-26 16:56:11 +02:00