linux/drivers/net/phy/Kconfig

467 lines
12 KiB

phylink: add phylink infrastructure The link between the ethernet MAC and its PHY has become more complex as the interface evolves. This is especially true with serdes links, where the part of the PHY is effectively integrated into the MAC. Serdes links can be connected to a variety of devices, including SFF modules soldered down onto the board with the MAC, a SFP cage with a hotpluggable SFP module which may contain a PHY or directly modulate the serdes signals onto optical media with or without a PHY, or even a classical PHY connection. Moreover, the negotiation information on serdes links comes in two varieties - SGMII mode, where the PHY provides its speed/duplex/flow control information to the MAC, and 1000base-X mode where both ends exchange their abilities and each resolve the link capabilities. This means we need a more flexible means to support these arrangements, particularly with the hotpluggable nature of SFP, where the PHY can be attached or detached after the network device has been brought up. Ethtool information can come from multiple sources: - we may have a PHY operating in either SGMII or 1000base-X mode, in which case we take ethtool/mii data directly from the PHY. - we may have a optical SFP module without a PHY, with the MAC operating in 1000base-X mode - the ethtool/mii data needs to come from the MAC. - we may have a copper SFP module with a PHY whic can't be accessed, which means we need to take ethtool/mii data from the MAC. Phylink aims to solve this by providing an intermediary between the MAC and PHY, providing a safe way for PHYs to be hotplugged, and allowing a SFP driver to reconfigure the serdes connection. Phylink also takes over support of fixed link connections, where the speed/duplex/flow control are fixed, but link status may be controlled by a GPIO signal. By avoiding the fixed-phy implementation, phylink can provide a faster response to link events: fixed-phy has to wait for phylib to operate its state machine, which can take several seconds. In comparison, phylink takes milliseconds. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> - remove sync status - rework supported and advertisment handling - add 1000base-x speed for fixed links - use functionality exported from phy-core, reworking __phylink_ethtool_ksettings_set for it Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-25 15:03:13 +01:00
ethernet: fix PTP_1588_CLOCK dependencies The 'imply' keyword does not do what most people think it does, it only politely asks Kconfig to turn on another symbol, but does not prevent it from being disabled manually or built as a loadable module when the user is built-in. In the ICE driver, the latter now causes a link failure: aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl': ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config' ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config' aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config' ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config' aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset': ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release' ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release' aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild': This is a recurring problem in many drivers, and we have discussed it several times befores, without reaching a consensus. I'm providing a link to the previous email thread for reference, which discusses some related problems. To solve the dependency issue better than the 'imply' keyword, introduce a separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver can depend on if it is able to use PTP support when available, but works fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are then prevented from being built-in, the same way as with a 'depends on PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick, but that can be rather confusing when you first see it. Since this should cover the dependencies correctly, the IS_REACHABLE() hack in the header is no longer needed now, and can be turned back into a normal IS_ENABLED() check. Any driver that gets the dependency wrong will now cause a link time failure rather than being unable to use PTP support when that is in a loadable module. However, the two recently added ptp_get_vclocks_index() and ptp_convert_timestamp() interfaces are only called from builtin code with ethtool and socket timestamps, so keep the current behavior by stubbing those out completely when PTP is in a loadable module. This should be addressed properly in a follow-up. As Richard suggested, we may want to actually turn PTP support into a 'bool' option later on, preventing it from being a loadable module altogether, which would be one way to solve the problem with the ethtool interface. Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices") Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/ Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/ Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/ Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/ Acked-by: Shannon Nelson <snelson@pensando.io> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-12 20:33:58 +02:00
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 11:51:35 +00:00
net: phy: add basic driver for NXP CBTX PHY The CBTX PHY is a Fast Ethernet PHY integrated into the SJA1110 A/B/C automotive Ethernet switches. It was hoped it would work with the Generic PHY driver, but alas, it doesn't. The most important reason why is that the PHY is powered down by default, and it needs a vendor register to power it on. It has a linear memory map that is accessed over SPI by the SJA1110 switch driver, which exposes a fake MDIO controller. It has the following (and only the following) standard clause 22 registers: 0x0: MII_BMCR 0x1: MII_BMSR 0x2: MII_PHYSID1 0x3: MII_PHYSID2 0x4: MII_ADVERTISE 0x5: MII_LPA 0x6: MII_EXPANSION 0x7: the missing MII_NPAGE for Next Page Transmit Register Every other register is vendor-defined. The register map expands the standard clause 22 5-bit address space of 0x20 registers, however the driver does not need to access the extra registers for now (and hopefully never). If it ever needs to do that, it is possible to implement a fake (software) page switching mechanism between the PHY driver and the SJA1110 MDIO controller driver. Also, Auto-MDIX is turned off by default in hardware, the driver turns it on by default and reports the current status. I've tested this with a VSC8514 link partner and a crossover cable, by forcing the mode on the link partner, and seeing that the CBTX PHY always sees the reverse of the mode forced on the VSC8514 (and that traffic works). The link doesn't come up (as expected) if MDI modes are forced on both ends in the same way (with the cross-over cable, that is). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230418190141.1040562-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-04-18 22:01:41 +03:00
ethernet: fix PTP_1588_CLOCK dependencies The 'imply' keyword does not do what most people think it does, it only politely asks Kconfig to turn on another symbol, but does not prevent it from being disabled manually or built as a loadable module when the user is built-in. In the ICE driver, the latter now causes a link failure: aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl': ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config' ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config' aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config' ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config' aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset': ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release' ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release' aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild': This is a recurring problem in many drivers, and we have discussed it several times befores, without reaching a consensus. I'm providing a link to the previous email thread for reference, which discusses some related problems. To solve the dependency issue better than the 'imply' keyword, introduce a separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver can depend on if it is able to use PTP support when available, but works fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are then prevented from being built-in, the same way as with a 'depends on PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick, but that can be rather confusing when you first see it. Since this should cover the dependencies correctly, the IS_REACHABLE() hack in the header is no longer needed now, and can be turned back into a normal IS_ENABLED() check. Any driver that gets the dependency wrong will now cause a link time failure rather than being unable to use PTP support when that is in a loadable module. However, the two recently added ptp_get_vclocks_index() and ptp_convert_timestamp() interfaces are only called from builtin code with ethtool and socket timestamps, so keep the current behavior by stubbing those out completely when PTP is in a loadable module. This should be addressed properly in a follow-up. As Richard suggested, we may want to actually turn PTP support into a 'bool' option later on, preventing it from being a loadable module altogether, which would be one way to solve the problem with the ethtool interface. Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices") Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/ Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/ Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/ Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/ Acked-by: Shannon Nelson <snelson@pensando.io> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-12 20:33:58 +02:00