linux/include/linux/suspend.h

456 lines
16 KiB

PM / Suspend: Add statistics debugfs file for suspend to RAM Record S3 failure time about each reason and the latest two failed devices' names in S3 progress. We can check it through 'suspend_stats' entry in debugfs. The motivation of the patch: We are enabling power features on Medfield. Comparing with PC/notebook, a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far more frequently. If it can't enter suspend-2-ram in time, the power might be used up soon. We often find sometimes, a device suspend fails. Then, system retries s3 over and over again. As display is off, testers and developers don't know what happens. Some testers and developers complain they don't know if system tries suspend-2-ram, and what device fails to suspend. They need such info for a quick check. The patch adds suspend_stats under debugfs for users to check suspend to RAM statistics quickly. If not using this patch, we have other methods to get info about what device fails. One is to turn on CONFIG_PM_DEBUG, but users would get too much info and testers need recompile the system. In addition, dynamic debug is another good tool to dump debug info. But it still doesn't match our utilization scenario closely. 1) user need write a user space parser to process the syslog output; 2) Our testing scenario is we leave the mobile for at least hours. Then, check its status. No serial console available during the testing. One is because console would be suspended, and the other is serial console connecting with spi or HSU devices would consume power. These devices are powered off at suspend-2-ram. Signed-off-by: ShuoX Liu <shuox.liu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-08-10 23:01:26 +02:00
PM / Sleep: Introduce "late suspend" and "early resume" of devices The current device suspend/resume phases during system-wide power transitions appear to be insufficient for some platforms that want to use the same callback routines for saving device states and related operations during runtime suspend/resume as well as during system suspend/resume. In principle, they could point their .suspend_noirq() and .resume_noirq() to the same callback routines as their .runtime_suspend() and .runtime_resume(), respectively, but at least some of them require device interrupts to be enabled while the code in those routines is running. It also makes sense to have device suspend-resume callbacks that will be executed with runtime PM disabled and with device interrupts enabled in case someone needs to run some special code in that context during system-wide power transitions. Apart from this, .suspend_noirq() and .resume_noirq() were introduced as a workaround for drivers using shared interrupts and failing to prevent their interrupt handlers from accessing suspended hardware. It appears to be better not to use them for other porposes, or we may have to deal with some serious confusion (which seems to be happening already). For the above reasons, introduce new device suspend/resume phases, "late suspend" and "early resume" (and analogously for hibernation) whose callback will be executed with runtime PM disabled and with device interrupts enabled and whose callback pointers generally may point to runtime suspend/resume routines. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
2012-01-29 20:38:29 +01:00
PM / Suspend: Add statistics debugfs file for suspend to RAM Record S3 failure time about each reason and the latest two failed devices' names in S3 progress. We can check it through 'suspend_stats' entry in debugfs. The motivation of the patch: We are enabling power features on Medfield. Comparing with PC/notebook, a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far more frequently. If it can't enter suspend-2-ram in time, the power might be used up soon. We often find sometimes, a device suspend fails. Then, system retries s3 over and over again. As display is off, testers and developers don't know what happens. Some testers and developers complain they don't know if system tries suspend-2-ram, and what device fails to suspend. They need such info for a quick check. The patch adds suspend_stats under debugfs for users to check suspend to RAM statistics quickly. If not using this patch, we have other methods to get info about what device fails. One is to turn on CONFIG_PM_DEBUG, but users would get too much info and testers need recompile the system. In addition, dynamic debug is another good tool to dump debug info. But it still doesn't match our utilization scenario closely. 1) user need write a user space parser to process the syslog output; 2) Our testing scenario is we leave the mobile for at least hours. Then, check its status. No serial console available during the testing. One is because console would be suspended, and the other is serial console connecting with spi or HSU devices would consume power. These devices are powered off at suspend-2-ram. Signed-off-by: ShuoX Liu <shuox.liu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-08-10 23:01:26 +02:00
PM / Sleep: Introduce "late suspend" and "early resume" of devices The current device suspend/resume phases during system-wide power transitions appear to be insufficient for some platforms that want to use the same callback routines for saving device states and related operations during runtime suspend/resume as well as during system suspend/resume. In principle, they could point their .suspend_noirq() and .resume_noirq() to the same callback routines as their .runtime_suspend() and .runtime_resume(), respectively, but at least some of them require device interrupts to be enabled while the code in those routines is running. It also makes sense to have device suspend-resume callbacks that will be executed with runtime PM disabled and with device interrupts enabled in case someone needs to run some special code in that context during system-wide power transitions. Apart from this, .suspend_noirq() and .resume_noirq() were introduced as a workaround for drivers using shared interrupts and failing to prevent their interrupt handlers from accessing suspended hardware. It appears to be better not to use them for other porposes, or we may have to deal with some serious confusion (which seems to be happening already). For the above reasons, introduce new device suspend/resume phases, "late suspend" and "early resume" (and analogously for hibernation) whose callback will be executed with runtime PM disabled and with device interrupts enabled and whose callback pointers generally may point to runtime suspend/resume routines. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
2012-01-29 20:38:29 +01:00
PM / Suspend: Add statistics debugfs file for suspend to RAM Record S3 failure time about each reason and the latest two failed devices' names in S3 progress. We can check it through 'suspend_stats' entry in debugfs. The motivation of the patch: We are enabling power features on Medfield. Comparing with PC/notebook, a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far more frequently. If it can't enter suspend-2-ram in time, the power might be used up soon. We often find sometimes, a device suspend fails. Then, system retries s3 over and over again. As display is off, testers and developers don't know what happens. Some testers and developers complain they don't know if system tries suspend-2-ram, and what device fails to suspend. They need such info for a quick check. The patch adds suspend_stats under debugfs for users to check suspend to RAM statistics quickly. If not using this patch, we have other methods to get info about what device fails. One is to turn on CONFIG_PM_DEBUG, but users would get too much info and testers need recompile the system. In addition, dynamic debug is another good tool to dump debug info. But it still doesn't match our utilization scenario closely. 1) user need write a user space parser to process the syslog output; 2) Our testing scenario is we leave the mobile for at least hours. Then, check its status. No serial console available during the testing. One is because console would be suspended, and the other is serial console connecting with spi or HSU devices would consume power. These devices are powered off at suspend-2-ram. Signed-off-by: ShuoX Liu <shuox.liu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-08-10 23:01:26 +02:00
PM / Sleep: Introduce "late suspend" and "early resume" of devices The current device suspend/resume phases during system-wide power transitions appear to be insufficient for some platforms that want to use the same callback routines for saving device states and related operations during runtime suspend/resume as well as during system suspend/resume. In principle, they could point their .suspend_noirq() and .resume_noirq() to the same callback routines as their .runtime_suspend() and .runtime_resume(), respectively, but at least some of them require device interrupts to be enabled while the code in those routines is running. It also makes sense to have device suspend-resume callbacks that will be executed with runtime PM disabled and with device interrupts enabled in case someone needs to run some special code in that context during system-wide power transitions. Apart from this, .suspend_noirq() and .resume_noirq() were introduced as a workaround for drivers using shared interrupts and failing to prevent their interrupt handlers from accessing suspended hardware. It appears to be better not to use them for other porposes, or we may have to deal with some serious confusion (which seems to be happening already). For the above reasons, introduce new device suspend/resume phases, "late suspend" and "early resume" (and analogously for hibernation) whose callback will be executed with runtime PM disabled and with device interrupts enabled and whose callback pointers generally may point to runtime suspend/resume routines. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
2012-01-29 20:38:29 +01:00
PM / Suspend: Add statistics debugfs file for suspend to RAM Record S3 failure time about each reason and the latest two failed devices' names in S3 progress. We can check it through 'suspend_stats' entry in debugfs. The motivation of the patch: We are enabling power features on Medfield. Comparing with PC/notebook, a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far more frequently. If it can't enter suspend-2-ram in time, the power might be used up soon. We often find sometimes, a device suspend fails. Then, system retries s3 over and over again. As display is off, testers and developers don't know what happens. Some testers and developers complain they don't know if system tries suspend-2-ram, and what device fails to suspend. They need such info for a quick check. The patch adds suspend_stats under debugfs for users to check suspend to RAM statistics quickly. If not using this patch, we have other methods to get info about what device fails. One is to turn on CONFIG_PM_DEBUG, but users would get too much info and testers need recompile the system. In addition, dynamic debug is another good tool to dump debug info. But it still doesn't match our utilization scenario closely. 1) user need write a user space parser to process the syslog output; 2) Our testing scenario is we leave the mobile for at least hours. Then, check its status. No serial console available during the testing. One is because console would be suspended, and the other is serial console connecting with spi or HSU devices would consume power. These devices are powered off at suspend-2-ram. Signed-off-by: ShuoX Liu <shuox.liu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-08-10 23:01:26 +02:00
PM / Sleep: Introduce "late suspend" and "early resume" of devices The current device suspend/resume phases during system-wide power transitions appear to be insufficient for some platforms that want to use the same callback routines for saving device states and related operations during runtime suspend/resume as well as during system suspend/resume. In principle, they could point their .suspend_noirq() and .resume_noirq() to the same callback routines as their .runtime_suspend() and .runtime_resume(), respectively, but at least some of them require device interrupts to be enabled while the code in those routines is running. It also makes sense to have device suspend-resume callbacks that will be executed with runtime PM disabled and with device interrupts enabled in case someone needs to run some special code in that context during system-wide power transitions. Apart from this, .suspend_noirq() and .resume_noirq() were introduced as a workaround for drivers using shared interrupts and failing to prevent their interrupt handlers from accessing suspended hardware. It appears to be better not to use them for other porposes, or we may have to deal with some serious confusion (which seems to be happening already). For the above reasons, introduce new device suspend/resume phases, "late suspend" and "early resume" (and analogously for hibernation) whose callback will be executed with runtime PM disabled and with device interrupts enabled and whose callback pointers generally may point to runtime suspend/resume routines. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
2012-01-29 20:38:29 +01:00
PM / Suspend: Add statistics debugfs file for suspend to RAM Record S3 failure time about each reason and the latest two failed devices' names in S3 progress. We can check it through 'suspend_stats' entry in debugfs. The motivation of the patch: We are enabling power features on Medfield. Comparing with PC/notebook, a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far more frequently. If it can't enter suspend-2-ram in time, the power might be used up soon. We often find sometimes, a device suspend fails. Then, system retries s3 over and over again. As display is off, testers and developers don't know what happens. Some testers and developers complain they don't know if system tries suspend-2-ram, and what device fails to suspend. They need such info for a quick check. The patch adds suspend_stats under debugfs for users to check suspend to RAM statistics quickly. If not using this patch, we have other methods to get info about what device fails. One is to turn on CONFIG_PM_DEBUG, but users would get too much info and testers need recompile the system. In addition, dynamic debug is another good tool to dump debug info. But it still doesn't match our utilization scenario closely. 1) user need write a user space parser to process the syslog output; 2) Our testing scenario is we leave the mobile for at least hours. Then, check its status. No serial console available during the testing. One is because console would be suspended, and the other is serial console connecting with spi or HSU devices would consume power. These devices are powered off at suspend-2-ram. Signed-off-by: ShuoX Liu <shuox.liu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-08-10 23:01:26 +02:00
PM / Suspend: Add .suspend_again() callback to suspend_ops A system or a device may need to control suspend/wakeup events. It may want to wakeup the system after a predefined amount of time or at a predefined event decided while entering suspend for polling or delayed work. Then, it may want to enter suspend again if its predefined wakeup condition is the only wakeup reason and there is no outstanding events; thus, it does not wakeup the userspace unnecessary or unnecessary devices and keeps suspended as long as possible (saving the power). Enabling a system to wakeup after a specified time can be easily achieved by using RTC. However, to enter suspend again immediately without invoking userland and unrelated devices, we need additional features in the suspend framework. Such need comes from: 1. Monitoring a critical device status without interrupts that can wakeup the system. (in-suspend polling) An example is ambient temperature monitoring that needs to shut down the system or a specific device function if it is too hot or cold. The temperature of a specific device may be needed to be monitored as well; e.g., a charger monitors battery temperature in order to stop charging if overheated. 2. Execute critical "delayed work" at suspend. A driver or a system/board may have a delayed work (or any similar things) that it wants to execute at the requested time. For example, some chargers want to check the battery voltage some time (e.g., 30 seconds) after the battery is fully charged and the charger has stopped. Then, the charger restarts charging if the voltage has dropped more than a threshold, which is smaller than "restart-charger" voltage, which is a threshold to restart charging regardless of the time passed. This patch allows to add "suspend_again" callback at struct platform_suspend_ops and let the "suspend_again" callback return true if the system is required to enter suspend again after the current instance of wakeup. Device-wise suspend_again implemented at dev_pm_ops or syscore is not done because: a) suspend_again feature is usually under platform-wise decision and controls the behavior of the whole platform and b) There are very limited devices related to the usage cases of suspend_again; chargers and temperature sensors are mentioned so far. With suspend_again callback registered at struct platform_suspend_ops suspend_ops in kernel/power/suspend.c with suspend_set_ops by the platform, the suspend framework tries to enter suspend again by looping suspend_enter() if suspend_again has returned true and there has been no errors in the suspending sequence or pending wakeups (by pm_wakeup_pending). Tested at Exynos4-NURI. [rjw: Fixed up kerneldoc comment for suspend_enter().] Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-06-12 15:57:05 +02:00
PM / Suspend: Add .suspend_again() callback to suspend_ops A system or a device may need to control suspend/wakeup events. It may want to wakeup the system after a predefined amount of time or at a predefined event decided while entering suspend for polling or delayed work. Then, it may want to enter suspend again if its predefined wakeup condition is the only wakeup reason and there is no outstanding events; thus, it does not wakeup the userspace unnecessary or unnecessary devices and keeps suspended as long as possible (saving the power). Enabling a system to wakeup after a specified time can be easily achieved by using RTC. However, to enter suspend again immediately without invoking userland and unrelated devices, we need additional features in the suspend framework. Such need comes from: 1. Monitoring a critical device status without interrupts that can wakeup the system. (in-suspend polling) An example is ambient temperature monitoring that needs to shut down the system or a specific device function if it is too hot or cold. The temperature of a specific device may be needed to be monitored as well; e.g., a charger monitors battery temperature in order to stop charging if overheated. 2. Execute critical "delayed work" at suspend. A driver or a system/board may have a delayed work (or any similar things) that it wants to execute at the requested time. For example, some chargers want to check the battery voltage some time (e.g., 30 seconds) after the battery is fully charged and the charger has stopped. Then, the charger restarts charging if the voltage has dropped more than a threshold, which is smaller than "restart-charger" voltage, which is a threshold to restart charging regardless of the time passed. This patch allows to add "suspend_again" callback at struct platform_suspend_ops and let the "suspend_again" callback return true if the system is required to enter suspend again after the current instance of wakeup. Device-wise suspend_again implemented at dev_pm_ops or syscore is not done because: a) suspend_again feature is usually under platform-wise decision and controls the behavior of the whole platform and b) There are very limited devices related to the usage cases of suspend_again; chargers and temperature sensors are mentioned so far. With suspend_again callback registered at struct platform_suspend_ops suspend_ops in kernel/power/suspend.c with suspend_set_ops by the platform, the suspend framework tries to enter suspend again by looping suspend_enter() if suspend_again has returned true and there has been no errors in the suspending sequence or pending wakeups (by pm_wakeup_pending). Tested at Exynos4-NURI. [rjw: Fixed up kerneldoc comment for suspend_enter().] Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-06-12 15:57:05 +02:00
[PATCH] swsusp: Improve handling of highmem Currently swsusp saves the contents of highmem pages by copying them to the normal zone which is quite inefficient (eg. it requires two normal pages to be used for saving one highmem page). This may be improved by using highmem for saving the contents of saveable highmem pages. Namely, during the suspend phase of the suspend-resume cycle we try to allocate as many free highmem pages as there are saveable highmem pages. If there are not enough highmem image pages to store the contents of all of the saveable highmem pages, some of them will be stored in the "normal" memory. Next, we allocate as many free "normal" pages as needed to store the (remaining) image data. We use a memory bitmap to mark the allocated free pages (ie. highmem as well as "normal" image pages). Now, we use another memory bitmap to mark all of the saveable pages (highmem as well as "normal") and the contents of the saveable pages are copied into the image pages. Then, the second bitmap is used to save the pfns corresponding to the saveable pages and the first one is used to save their data. During the resume phase the pfns of the pages that were saveable during the suspend are loaded from the image and used to mark the "unsafe" page frames. Next, we try to allocate as many free highmem page frames as to load all of the image data that had been in the highmem before the suspend and we allocate so many free "normal" page frames that the total number of allocated free pages (highmem and "normal") is equal to the size of the image. While doing this we have to make sure that there will be some extra free "normal" and "safe" page frames for two lists of PBEs constructed later. Now, the image data are loaded, if possible, into their "original" page frames. The image data that cannot be written into their "original" page frames are loaded into "safe" page frames and their "original" kernel virtual addresses, as well as the addresses of the "safe" pages containing their copies, are stored in one of two lists of PBEs. One list of PBEs is for the copies of "normal" suspend pages (ie. "normal" pages that were saveable during the suspend) and it is used in the same way as previously (ie. by the architecture-dependent parts of swsusp). The other list of PBEs is for the copies of highmem suspend pages. The pages in this list are restored (in a reversible way) right before the arch-dependent code is called. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-06 20:34:18 -08:00
[PATCH] swsusp: Improve handling of highmem Currently swsusp saves the contents of highmem pages by copying them to the normal zone which is quite inefficient (eg. it requires two normal pages to be used for saving one highmem page). This may be improved by using highmem for saving the contents of saveable highmem pages. Namely, during the suspend phase of the suspend-resume cycle we try to allocate as many free highmem pages as there are saveable highmem pages. If there are not enough highmem image pages to store the contents of all of the saveable highmem pages, some of them will be stored in the "normal" memory. Next, we allocate as many free "normal" pages as needed to store the (remaining) image data. We use a memory bitmap to mark the allocated free pages (ie. highmem as well as "normal" image pages). Now, we use another memory bitmap to mark all of the saveable pages (highmem as well as "normal") and the contents of the saveable pages are copied into the image pages. Then, the second bitmap is used to save the pfns corresponding to the saveable pages and the first one is used to save their data. During the resume phase the pfns of the pages that were saveable during the suspend are loaded from the image and used to mark the "unsafe" page frames. Next, we try to allocate as many free highmem page frames as to load all of the image data that had been in the highmem before the suspend and we allocate so many free "normal" page frames that the total number of allocated free pages (highmem and "normal") is equal to the size of the image. While doing this we have to make sure that there will be some extra free "normal" and "safe" page frames for two lists of PBEs constructed later. Now, the image data are loaded, if possible, into their "original" page frames. The image data that cannot be written into their "original" page frames are loaded into "safe" page frames and their "original" kernel virtual addresses, as well as the addresses of the "safe" pages containing their copies, are stored in one of two lists of PBEs. One list of PBEs is for the copies of "normal" suspend pages (ie. "normal" pages that were saveable during the suspend) and it is used in the same way as previously (ie. by the architecture-dependent parts of swsusp). The other list of PBEs is for the copies of highmem suspend pages. The pages in this list are restored (in a reversible way) right before the arch-dependent code is called. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-06 20:34:18 -08:00
swsusp: introduce restore platform operations At least on some machines it is necessary to prepare the ACPI firmware for the restoration of the system memory state from the hibernation image if the "platform" mode of hibernation has been used. Namely, in that cases we need to disable the GPEs before replacing the "boot" kernel with the "frozen" kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the restore they will be re-enabled by hibernation_ops->finish(), but if the restore fails, they have to be re-enabled by the restore code explicitly. For this purpose we can introduce two additional hibernation operations, called pre_restore() and restore_cleanup() and call them from the restore code path. Still, they should be called if the "platform" mode of hibernation has been used, so we need to pass the information about the hibernation mode from the "frozen" kernel to the "boot" kernel in the image header. Apparently, we can't drop the disabling of GPEs before the restore because of Bug #7887 .  We also can't do it unconditionally, because the GPEs wouldn't have been enabled after a successful restore if the suspend had been done in the 'shutdown' or 'reboot' mode. In principle we could (and probably should) unconditionally disable the GPEs before each snapshot creation *and* before the restore, but then we'd have to unconditionally enable them after the snapshot creation as well as after the restore (or restore failure)   Still, for this purpose we'd need to modify acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to introduce some mechanism synchronizing the disablind/enabling of the GPEs with the device drivers' .suspend()/.resume() routines and with disable_/enable_nonboot_cpus().  However, this would have affected the suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid in this patch series. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Nigel Cunningham <nigel@nigel.suspend2.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-19 01:47:30 -07:00
PM: Make it possible to avoid races between wakeup and system sleep One of the arguments during the suspend blockers discussion was that the mainline kernel didn't contain any mechanisms making it possible to avoid races between wakeup and system suspend. Generally, there are two problems in that area. First, if a wakeup event occurs exactly when /sys/power/state is being written to, it may be delivered to user space right before the freezer kicks in, so the user space consumer of the event may not be able to process it before the system is suspended. Second, if a wakeup event occurs after user space has been frozen, it is not generally guaranteed that the ongoing transition of the system into a sleep state will be aborted. To address these issues introduce a new global sysfs attribute, /sys/power/wakeup_count, associated with a running counter of wakeup events and three helper functions, pm_stay_awake(), pm_relax(), and pm_wakeup_event(), that may be used by kernel subsystems to control the behavior of this attribute and to request the PM core to abort system transitions into a sleep state already in progress. The /sys/power/wakeup_count file may be read from or written to by user space. Reads will always succeed (unless interrupted by a signal) and return the current value of the wakeup events counter. Writes, however, will only succeed if the written number is equal to the current value of the wakeup events counter. If a write is successful, it will cause the kernel to save the current value of the wakeup events counter and to abort the subsequent system transition into a sleep state if any wakeup events are reported after the write has returned. [The assumption is that before writing to /sys/power/state user space will first read from /sys/power/wakeup_count. Next, user space consumers of wakeup events will have a chance to acknowledge or veto the upcoming system transition to a sleep state. Finally, if the transition is allowed to proceed, /sys/power/wakeup_count will be written to and if that succeeds, /sys/power/state will be written to as well. Still, if any wakeup events are reported to the PM core by kernel subsystems after that point, the transition will be aborted.] Additionally, put a wakeup events counter into struct dev_pm_info and make these per-device wakeup event counters available via sysfs, so that it's possible to check the activity of various wakeup event sources within the kernel. To illustrate how subsystems can use pm_wakeup_event(), make the low-level PCI runtime PM wakeup-handling code use it. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: markgross <markgross@thegnar.org> Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
2010-07-05 22:43:53 +02:00
PM / Hibernate: Rewrite unlock_system_sleep() to fix s2disk regression Commit 33e638b, "PM / Sleep: Use the freezer_count() functions in [un]lock_system_sleep() APIs" introduced an undesirable change in the behaviour of unlock_system_sleep() since freezer_count() internally calls try_to_freeze() - which we don't need in unlock_system_sleep(). And commit bcda53f, "PM / Sleep: Replace mutex_[un]lock(&pm_mutex) with [un]lock_system_sleep()" made these APIs wide-spread. This caused a regression in suspend-to-disk where snapshot_read() and snapshot_write() were getting frozen due to the try_to_freeze embedded in unlock_system_sleep(), since these functions were invoked when the freezing condition was still in effect. Fix this by rewriting unlock_system_sleep() by open-coding freezer_count() and dropping the try_to_freeze() part. Not only will this fix the regression but this will also ensure that the API only does what it is intended to do, and nothing more, under the hood. While at it, make the code more correct and robust by ensuring that the PF_FREEZER_SKIP flag gets cleared with pm_mutex held, to avoid a race with the freezer. Also, to be on the safer side, open-code freezer_do_not_count() as well (inside lock_system_sleep()), to ensure that any unrelated modification to freezer[_do_not]_count() does not break things again! Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-01-19 23:25:33 +01:00
PM / Hibernate: Rewrite unlock_system_sleep() to fix s2disk regression Commit 33e638b, "PM / Sleep: Use the freezer_count() functions in [un]lock_system_sleep() APIs" introduced an undesirable change in the behaviour of unlock_system_sleep() since freezer_count() internally calls try_to_freeze() - which we don't need in unlock_system_sleep(). And commit bcda53f, "PM / Sleep: Replace mutex_[un]lock(&pm_mutex) with [un]lock_system_sleep()" made these APIs wide-spread. This caused a regression in suspend-to-disk where snapshot_read() and snapshot_write() were getting frozen due to the try_to_freeze embedded in unlock_system_sleep(), since these functions were invoked when the freezing condition was still in effect. Fix this by rewriting unlock_system_sleep() by open-coding freezer_count() and dropping the try_to_freeze() part. Not only will this fix the regression but this will also ensure that the API only does what it is intended to do, and nothing more, under the hood. While at it, make the code more correct and robust by ensuring that the PF_FREEZER_SKIP flag gets cleared with pm_mutex held, to avoid a race with the freezer. Also, to be on the safer side, open-code freezer_do_not_count() as well (inside lock_system_sleep()), to ensure that any unrelated modification to freezer[_do_not]_count() does not break things again! Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-01-19 23:25:33 +01:00