linux/drivers/gpu/drm/msm/msm_debugfs.c

420 lines
9 KiB

drm/msm: Implement fbdev emulation as in-kernel client Move code from ad-hoc fbdev callbacks into DRM client functions and remove the old callbacks. The functions instruct the client to poll for changed output or restore the display. The DRM core calls both, the old callbacks and the new client helpers, from the same places. The new functions perform the same operation as before, so there's no change in functionality. Replace all code that initializes or releases fbdev emulation throughout the driver. Instead initialize the fbdev client by a single call to msm_fbdev_setup() after msm has registered its DRM device. As in most drivers, msm's fbdev emulation now acts like a regular DRM client. The fbdev client setup consists of the initial preparation and the hot-plugging of the display. The latter creates the fbdev device and sets up the fbdev framebuffer. The setup performs display hot-plugging once. If no display can be detected, DRM probe helpers re-run the detection on each hotplug event. A call to drm_dev_unregister() releases the client automatically. No further action is required within msm. If the fbdev framebuffer has been fully set up, struct fb_ops.fb_destroy implements the release. For partially initialized emulation, the fbdev client reverts the initial setup. v2: * handle fbdev module parameter correctly (kernel test robot) Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # RB5 Patchwork: https://patchwork.freedesktop.org/patch/530560/ Link: https://lore.kernel.org/r/20230403124538.8497-9-tzimmermann@suse.de Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
2023-04-03 14:45:38 +02:00
drm/msm: Temporarily disable stall-on-fault after a page fault When things go wrong, the GPU is capable of quickly generating millions of faulting translation requests per second. When that happens, in the stall-on-fault model each access will stall until it wins the race to signal the fault and then the RESUME register is written. This slows processing page faults to a crawl as the GPU can generate faults much faster than the CPU can acknowledge them. It also means that all available resources in the SMMU are saturated waiting for the stalled transactions, so that other transactions such as transactions generated by the GMU, which shares translation resources with the GPU, cannot proceed. This causes a GMU watchdog timeout, which leads to a failed reset because GX cannot collapse when there is a transaction pending and a permanently hung GPU. On older platforms with qcom,smmu-v2, it seems that when one transaction is stalled subsequent faulting transactions are terminated, which avoids this problem, but the MMU-500 follows the spec here. To work around these problems, disable stall-on-fault as soon as we get a page fault until a cooldown period after pagefaults stop. This allows the GMU some guaranteed time to continue working. We only use stall-on-fault to halt the GPU while we collect a devcoredump and we always terminate the transaction afterward, so it's fine to miss some subsequent page faults. We also keep it disabled so long as the current devcoredump hasn't been deleted, because in that case we likely won't capture another one if there's a fault. After this commit HFI messages still occasionally time out, because the crashdump handler doesn't run fast enough to let the GMU resume, but the driver seems to recover from it. This will probably go away after the HFI timeout is increased. Signed-off-by: Connor Abbott <cwabbott0@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Patchwork: https://patchwork.freedesktop.org/patch/654891/ Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
2025-05-20 15:08:59 -04:00
drm/msm: Temporarily disable stall-on-fault after a page fault When things go wrong, the GPU is capable of quickly generating millions of faulting translation requests per second. When that happens, in the stall-on-fault model each access will stall until it wins the race to signal the fault and then the RESUME register is written. This slows processing page faults to a crawl as the GPU can generate faults much faster than the CPU can acknowledge them. It also means that all available resources in the SMMU are saturated waiting for the stalled transactions, so that other transactions such as transactions generated by the GMU, which shares translation resources with the GPU, cannot proceed. This causes a GMU watchdog timeout, which leads to a failed reset because GX cannot collapse when there is a transaction pending and a permanently hung GPU. On older platforms with qcom,smmu-v2, it seems that when one transaction is stalled subsequent faulting transactions are terminated, which avoids this problem, but the MMU-500 follows the spec here. To work around these problems, disable stall-on-fault as soon as we get a page fault until a cooldown period after pagefaults stop. This allows the GMU some guaranteed time to continue working. We only use stall-on-fault to halt the GPU while we collect a devcoredump and we always terminate the transaction afterward, so it's fine to miss some subsequent page faults. We also keep it disabled so long as the current devcoredump hasn't been deleted, because in that case we likely won't capture another one if there's a fault. After this commit HFI messages still occasionally time out, because the crashdump handler doesn't run fast enough to let the GMU resume, but the driver seems to recover from it. This will probably go away after the HFI timeout is increased. Signed-off-by: Connor Abbott <cwabbott0@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Patchwork: https://patchwork.freedesktop.org/patch/654891/ Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
2025-05-20 15:08:59 -04:00