linux/drivers/net/phy/marvell.c

4205 lines
105 KiB

of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
of/phylib: Use device tree properties to initialize Marvell PHYs. Some aspects of PHY initialization are board dependent, things like indicator LED connections and some clocking modes cannot be determined by probing. The dev_flags element of struct phy_device can be used to control these things if an appropriate value can be passed from the Ethernet driver. We run into problems however if the PHY connections are specified by the device tree. There is no way for the Ethernet driver to know what flags it should pass. If we are using the device tree, the struct phy_device will be populated with the device tree node corresponding to the PHY, and we can extract extra configuration information from there. The next question is what should the format of that information be? It is highly device specific, and the device tree representation should not be tied to any arbitrary kernel defined constants. A straight forward representation is just to specify the exact bits that should be set using the "marvell,reg-init" property: phy5: ethernet-phy@5 { reg = <5>; compatible = "marvell,88e1149r"; marvell,reg-init = /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */ <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */ /* mix %:0, led[0123]:drive low off hiZ */ <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */ /* default blink periods. */ <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */ /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */ <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */ }; phy6: ethernet-phy@6 { reg = <6>; compatible = "marvell,88e1118"; marvell,reg-init = /* Fix rx and tx clock transition timing */ <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */ /* Adjust LED drive. */ <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */ /* irq, blink-activity, blink-link */ <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */ }; The Marvell PHYs have a page select register at register 22 (0x16), we can specify any register by its page and register number. These are the first and second word. The third word contains a mask to be ANDed with the existing register value, and the fourth word is ORed with the result to yield the new register value. The new marvell_of_reg_init function leaves the page select register unchanged, so a call to it can be dropped into the .config_init functions without unduly affecting the state of the PHY. If CONFIG_OF_MDIO is not set, there is no of_node, or no "marvell,reg-init" property, the PHY initialization is unchanged. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Cyril Chemparathy <cyril@ti.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 12:13:18 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00
net: phy: marvell: fix paged access races For paged accesses to be truely safe, we need to hold the bus lock to prevent anyone else gaining access to the registers while we modify them. The phydev->lock mutex does not do this: userspace via the MII ioctl can still sneak in and read or write any register while we are on a different page, and the suspend/resume methods can be called by a thread different to the thread polling the phy status. Races have been observed with mvneta on SolidRun Clearfog with phylink, particularly between the phylib worker reading the PHYs status, and the thread resuming mvneta, calling phy_start() which then calls through to m88e1121_config_aneg_rgmii_delays(), which tries to read-modify-write the MSCR register: CPU0 CPU1 marvell_read_status_page() marvell_set_page(phydev, MII_MARVELL_FIBER_PAGE) ... m88e1121_config_aneg_rgmii_delays() set_page(MII_MARVELL_MSCR_PAGE) phy_read(phydev, MII_88E1121_PHY_MSCR_REG) marvell_set_page(phydev, MII_MARVELL_COPPER_PAGE); ... phy_write(phydev, MII_88E1121_PHY_MSCR_REG) The result of this is we end up writing the copper page register 21, which causes the copper PHY to be disabled, and the link partner sees the link immediately go down. Solve this by taking the bus lock instead of the PHY lock, thereby preventing other accesses to the PHY while we are accessing other PHY pages. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02 10:58:48 +00:00