linux/net/bridge/br_private.h

2364 lines
67 KiB

skbuff: bridge: Add layer 2 miss indication For EVPN non-DF (Designated Forwarder) filtering we need to be able to prevent decapsulated traffic from being flooded to a multi-homed host. Filtering of multicast and broadcast traffic can be achieved using the following flower filter: # tc filter add dev bond0 egress pref 1 proto all flower indev vxlan0 dst_mac 01:00:00:00:00:00/01:00:00:00:00:00 action drop Unlike broadcast and multicast traffic, it is not currently possible to filter unknown unicast traffic. The classification into unknown unicast is performed by the bridge driver, but is not visible to other layers such as tc. Solve this by adding a new 'l2_miss' bit to the tc skb extension. Clear the bit whenever a packet enters the bridge (received from a bridge port or transmitted via the bridge) and set it if the packet did not match an FDB or MDB entry. If there is no skb extension and the bit needs to be cleared, then do not allocate one as no extension is equivalent to the bit being cleared. The bit is not set for broadcast packets as they never perform a lookup and therefore never incur a miss. A bit that is set for every flooded packet would also work for the current use case, but it does not allow us to differentiate between registered and unregistered multicast traffic, which might be useful in the future. To keep the performance impact to a minimum, the marking of packets is guarded by the 'tc_skb_ext_tc' static key. When 'false', the skb is not touched and an skb extension is not allocated. Instead, only a 5 bytes nop is executed, as demonstrated below for the call site in br_handle_frame(). Before the patch: ``` memset(skb->cb, 0, sizeof(struct br_input_skb_cb)); c37b09: 49 c7 44 24 28 00 00 movq $0x0,0x28(%r12) c37b10: 00 00 p = br_port_get_rcu(skb->dev); c37b12: 49 8b 44 24 10 mov 0x10(%r12),%rax memset(skb->cb, 0, sizeof(struct br_input_skb_cb)); c37b17: 49 c7 44 24 30 00 00 movq $0x0,0x30(%r12) c37b1e: 00 00 c37b20: 49 c7 44 24 38 00 00 movq $0x0,0x38(%r12) c37b27: 00 00 ``` After the patch (when static key is disabled): ``` memset(skb->cb, 0, sizeof(struct br_input_skb_cb)); c37c29: 49 c7 44 24 28 00 00 movq $0x0,0x28(%r12) c37c30: 00 00 c37c32: 49 8d 44 24 28 lea 0x28(%r12),%rax c37c37: 48 c7 40 08 00 00 00 movq $0x0,0x8(%rax) c37c3e: 00 c37c3f: 48 c7 40 10 00 00 00 movq $0x0,0x10(%rax) c37c46: 00 #ifdef CONFIG_HAVE_JUMP_LABEL_HACK static __always_inline bool arch_static_branch(struct static_key *key, bool branch) { asm_volatile_goto("1:" c37c47: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1) br_tc_skb_miss_set(skb, false); p = br_port_get_rcu(skb->dev); c37c4c: 49 8b 44 24 10 mov 0x10(%r12),%rax ``` Subsequent patches will extend the flower classifier to be able to match on the new 'l2_miss' bit and enable / disable the static key when filters that match on it are added / deleted. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-05-29 14:48:28 +03:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
net: bridge: fix soft lockup in br_multicast_query_expired() When set multicast_query_interval to a large value, the local variable 'time' in br_multicast_send_query() may overflow. If the time is smaller than jiffies, the timer will expire immediately, and then call mod_timer() again, which creates a loop and may trigger the following soft lockup issue. watchdog: BUG: soft lockup - CPU#1 stuck for 221s! [rb_consumer:66] CPU: 1 UID: 0 PID: 66 Comm: rb_consumer Not tainted 6.16.0+ #259 PREEMPT(none) Call Trace: <IRQ> __netdev_alloc_skb+0x2e/0x3a0 br_ip6_multicast_alloc_query+0x212/0x1b70 __br_multicast_send_query+0x376/0xac0 br_multicast_send_query+0x299/0x510 br_multicast_query_expired.constprop.0+0x16d/0x1b0 call_timer_fn+0x3b/0x2a0 __run_timers+0x619/0x950 run_timer_softirq+0x11c/0x220 handle_softirqs+0x18e/0x560 __irq_exit_rcu+0x158/0x1a0 sysvec_apic_timer_interrupt+0x76/0x90 </IRQ> This issue can be reproduced with: ip link add br0 type bridge echo 1 > /sys/class/net/br0/bridge/multicast_querier echo 0xffffffffffffffff > /sys/class/net/br0/bridge/multicast_query_interval ip link set dev br0 up The multicast_startup_query_interval can also cause this issue. Similar to the commit 99b40610956a ("net: bridge: mcast: add and enforce query interval minimum"), add check for the query interval maximum to fix this issue. Link: https://lore.kernel.org/netdev/20250806094941.1285944-1-wangliang74@huawei.com/ Link: https://lore.kernel.org/netdev/20250812091818.542238-1-wangliang74@huawei.com/ Fixes: d902eee43f19 ("bridge: Add multicast count/interval sysfs entries") Suggested-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Wang Liang <wangliang74@huawei.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250813021054.1643649-1-wangliang74@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-08-13 10:10:54 +08:00
bridge: mcast: fix disabled snooping after long uptime The original idea of the delay_time check was to not apply multicast snooping too early when an MLD querier appears. And to instead wait at least for MLD reports to arrive before switching from flooding to group based, MLD snooped forwarding, to avoid temporary packet loss. However in a batman-adv mesh network it was noticed that after 248 days of uptime 32bit MIPS based devices would start to signal that they had stopped applying multicast snooping due to missing queriers - even though they were the elected querier and still sending MLD queries themselves. While time_is_before_jiffies() generally is safe against jiffies wrap-arounds, like the code comments in jiffies.h explain, it won't be able to track a difference larger than ULONG_MAX/2. With a 32bit large jiffies and one jiffies tick every 10ms (CONFIG_HZ=100) on these MIPS devices running OpenWrt this would result in a difference larger than ULONG_MAX/2 after 248 (= 2^32/100/60/60/24/2) days and time_is_before_jiffies() would then start to return false instead of true. Leading to multicast snooping not being applied to multicast packets anymore. Fix this issue by using a proper timer_list object which won't have this ULONG_MAX/2 difference limitation. Fixes: b00589af3b04 ("bridge: disable snooping if there is no querier") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20240127175033.9640-1-linus.luessing@c0d3.blue Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-01-27 18:50:32 +01:00
bridge: mcast: Support replacement of MDB port group entries Now that user space can specify additional attributes of port group entries such as filter mode and source list, it makes sense to allow user space to atomically modify these attributes by replacing entries instead of forcing user space to delete the entries and add them back. Replace MDB port group entries when the 'NLM_F_REPLACE' flag is specified in the netlink message header. When a (*, G) entry is replaced, update the following attributes: Source list, state, filter mode, protocol and flags. If the entry is temporary and in EXCLUDE mode, reset the group timer to the group membership interval. If the entry is temporary and in INCLUDE mode, reset the source timers of associated sources to the group membership interval. Examples: # bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.2 filter_mode include # bridge -d -s mdb show dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.2 permanent filter_mode include proto static 0.00 dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto static 0.00 dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode include source_list 192.0.2.2/0.00,192.0.2.1/0.00 proto static 0.00 # bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.3 filter_mode exclude proto zebra # bridge -d -s mdb show dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include proto zebra blocked 0.00 dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra blocked 0.00 dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list 192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00 # bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 temp source_list 192.0.2.4,192.0.2.3 filter_mode include proto bgp # bridge -d -s mdb show dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.4 temp filter_mode include proto bgp 0.00 dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 temp filter_mode include proto bgp 0.00 dev br0 port dummy10 grp 239.1.1.1 temp filter_mode include source_list 192.0.2.4/259.44,192.0.2.3/259.44 proto bgp 0.00 Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-10 16:56:31 +02:00
bridge: mcast: Allow user space to specify MDB entry routing protocol Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the routing protocol of the MDB port group entry. Enforce a minimum value of 'RTPROT_STATIC' to prevent user space from using protocol values that should only be set by the kernel (e.g., 'RTPROT_KERNEL'). Maintain backward compatibility by defaulting to 'RTPROT_STATIC'. The protocol is already visible to user space in RTM_NEWMDB responses and notifications via the 'MDBA_MDB_EATTR_RTPROT' attribute. The routing protocol allows a routing daemon to distinguish between entries configured by it and those configured by the administrator. Once MDB flush is supported, the protocol can be used as a criterion according to which the flush is performed. Examples: # bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto kernel Error: integer out of range. # bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto static # bridge mdb add dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent proto zebra # bridge mdb add dev br0 port dummy10 grp 239.1.1.2 permanent source_list 198.51.100.1,198.51.100.2 filter_mode include proto 250 # bridge -d mdb show dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.2 permanent filter_mode include proto 250 dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.1 permanent filter_mode include proto 250 dev br0 port dummy10 grp 239.1.1.2 permanent filter_mode include source_list 198.51.100.2/0.00,198.51.100.1/0.00 proto 250 dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude proto static Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-10 16:56:30 +02:00
net: bridge: Maintain number of MDB entries in net_bridge_mcast_port The MDB maintained by the bridge is limited. When the bridge is configured for IGMP / MLD snooping, a buggy or malicious client can easily exhaust its capacity. In SW datapath, the capacity is configurable through the IFLA_BR_MCAST_HASH_MAX parameter, but ultimately is finite. Obviously a similar limit exists in the HW datapath for purposes of offloading. In order to prevent the issue of unilateral exhaustion of MDB resources, introduce two parameters in each of two contexts: - Per-port and per-port-VLAN number of MDB entries that the port is member in. - Per-port and (when BROPT_MCAST_VLAN_SNOOPING_ENABLED is enabled) per-port-VLAN maximum permitted number of MDB entries, or 0 for no limit. The per-port multicast context is used for tracking of MDB entries for the port as a whole. This is available for all bridges. The per-port-VLAN multicast context is then only available on VLAN-filtering bridges on VLANs that have multicast snooping on. With these changes in place, it will be possible to configure MDB limit for bridge as a whole, or any one port as a whole, or any single port-VLAN. Note that unlike the global limit, exhaustion of the per-port and per-port-VLAN maximums does not cause disablement of multicast snooping. It is also permitted to configure the local limit larger than hash_max, even though that is not useful. In this patch, introduce only the accounting for number of entries, and the max field itself, but not the means to toggle the max. The next patch introduces the netlink APIs to toggle and read the values. Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-02 18:59:25 +01:00
bridge: per vlan dst_metadata netlink support This patch adds support to attach per vlan tunnel info dst metadata. This enables bridge driver to map vlan to tunnel_info at ingress and egress. It uses the kernel dst_metadata infrastructure. The initial use case is vlan to vni bridging, but the api is generic to extend to any tunnel_info in the future: - Uapi to configure/unconfigure/dump per vlan tunnel data - netlink functions to configure vlan and tunnel_info mapping - Introduces bridge port flag BR_LWT_VLAN to enable attach/detach dst_metadata to bridged packets on ports. off by default. - changes to existing code is mainly refactor some existing vlan handling netlink code + hooks for new vlan tunnel code - I have kept the vlan tunnel code isolated in separate files. - most of the netlink vlan tunnel code is handling of vlan-tunid ranges (follows the vlan range handling code). To conserve space vlan-tunid by default are always dumped in ranges if applicable. Use case: example use for this is a vxlan bridging gateway or vtep which maps vlans to vn-segments (or vnis). iproute2 example (patched and pruned iproute2 output to just show relevant fdb entries): example shows same host mac learnt on two vni's and vlan 100 maps to vni 1000, vlan 101 maps to vni 1001 before (netdev per vni): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self after this patch with collect metdata in bridged mode (single netdev): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31 22:59:54 -08:00
bridge: per vlan dst_metadata netlink support This patch adds support to attach per vlan tunnel info dst metadata. This enables bridge driver to map vlan to tunnel_info at ingress and egress. It uses the kernel dst_metadata infrastructure. The initial use case is vlan to vni bridging, but the api is generic to extend to any tunnel_info in the future: - Uapi to configure/unconfigure/dump per vlan tunnel data - netlink functions to configure vlan and tunnel_info mapping - Introduces bridge port flag BR_LWT_VLAN to enable attach/detach dst_metadata to bridged packets on ports. off by default. - changes to existing code is mainly refactor some existing vlan handling netlink code + hooks for new vlan tunnel code - I have kept the vlan tunnel code isolated in separate files. - most of the netlink vlan tunnel code is handling of vlan-tunid ranges (follows the vlan range handling code). To conserve space vlan-tunid by default are always dumped in ranges if applicable. Use case: example use for this is a vxlan bridging gateway or vtep which maps vlans to vn-segments (or vnis). iproute2 example (patched and pruned iproute2 output to just show relevant fdb entries): example shows same host mac learnt on two vni's and vlan 100 maps to vni 1000, vlan 101 maps to vni 1001 before (netdev per vni): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self after this patch with collect metdata in bridged mode (single netdev): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31 22:59:54 -08:00
net: bridge: Fix VLANs memory leak When adding / deleting VLANs to / from a bridge port, the bridge driver first tries to propagate the information via switchdev and falls back to the 8021q driver in case the underlying driver does not support switchdev. This can result in a memory leak [1] when VXLAN and mlxsw ports are enslaved to the bridge: $ ip link set dev vxlan0 master br0 # No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev # notification and the bridge driver adds the VLAN on 'vxlan0' via the # 8021q driver $ bridge vlan add vid 10 dev vxlan0 pvid untagged # mlxsw port is enslaved to the bridge $ ip link set dev swp1 master br0 # mlxsw processes the switchdev notification and the 8021q driver is # skipped $ bridge vlan del vid 10 dev vxlan0 This results in 'struct vlan_info' and 'struct vlan_vid_info' being leaked, as they were allocated by the 8021q driver during VLAN addition, but never freed as the 8021q driver was skipped during deletion. Fix this by introducing a new VLAN private flag that indicates whether the VLAN was added on the port by switchdev or the 8021q driver. If the VLAN was added by the 8021q driver, then we make sure to delete it via the 8021q driver as well. [1] unreferenced object 0xffff88822d20b1e8 (size 256): comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s) hex dump (first 32 bytes): e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B.............. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330 [<00000000e0178b02>] vlan_vid_add+0x661/0x920 [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00 [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90 [<000000003535392c>] br_vlan_info+0x132/0x410 [<00000000aedaa9dc>] br_afspec+0x75c/0x870 [<00000000f5716133>] br_setlink+0x3dc/0x6d0 [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30 [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80 [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0 [<000000008be8d614>] rtnetlink_rcv+0x21/0x30 [<000000009ab2ca25>] netlink_unicast+0x52f/0x740 [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50 [<000000005d1e2050>] sock_sendmsg+0xbe/0x120 [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0 [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270 unreferenced object 0xffff888227454308 (size 32): comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s) hex dump (first 32 bytes): 88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -.... 81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330 [<0000000018050631>] vlan_vid_add+0x3e6/0x920 [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00 [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90 [<000000003535392c>] br_vlan_info+0x132/0x410 [<00000000aedaa9dc>] br_afspec+0x75c/0x870 [<00000000f5716133>] br_setlink+0x3dc/0x6d0 [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30 [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80 [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0 [<000000008be8d614>] rtnetlink_rcv+0x21/0x30 [<000000009ab2ca25>] netlink_unicast+0x52f/0x740 [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50 [<000000005d1e2050>] sock_sendmsg+0xbe/0x120 [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0 [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270 Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: bridge@lists.linux-foundation.org Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-08 16:48:11 +00:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: per vlan dst_metadata netlink support This patch adds support to attach per vlan tunnel info dst metadata. This enables bridge driver to map vlan to tunnel_info at ingress and egress. It uses the kernel dst_metadata infrastructure. The initial use case is vlan to vni bridging, but the api is generic to extend to any tunnel_info in the future: - Uapi to configure/unconfigure/dump per vlan tunnel data - netlink functions to configure vlan and tunnel_info mapping - Introduces bridge port flag BR_LWT_VLAN to enable attach/detach dst_metadata to bridged packets on ports. off by default. - changes to existing code is mainly refactor some existing vlan handling netlink code + hooks for new vlan tunnel code - I have kept the vlan tunnel code isolated in separate files. - most of the netlink vlan tunnel code is handling of vlan-tunid ranges (follows the vlan range handling code). To conserve space vlan-tunid by default are always dumped in ranges if applicable. Use case: example use for this is a vxlan bridging gateway or vtep which maps vlans to vn-segments (or vnis). iproute2 example (patched and pruned iproute2 output to just show relevant fdb entries): example shows same host mac learnt on two vni's and vlan 100 maps to vni 1000, vlan 101 maps to vni 1001 before (netdev per vni): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self after this patch with collect metdata in bridged mode (single netdev): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31 22:59:54 -08:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: per vlan dst_metadata netlink support This patch adds support to attach per vlan tunnel info dst metadata. This enables bridge driver to map vlan to tunnel_info at ingress and egress. It uses the kernel dst_metadata infrastructure. The initial use case is vlan to vni bridging, but the api is generic to extend to any tunnel_info in the future: - Uapi to configure/unconfigure/dump per vlan tunnel data - netlink functions to configure vlan and tunnel_info mapping - Introduces bridge port flag BR_LWT_VLAN to enable attach/detach dst_metadata to bridged packets on ports. off by default. - changes to existing code is mainly refactor some existing vlan handling netlink code + hooks for new vlan tunnel code - I have kept the vlan tunnel code isolated in separate files. - most of the netlink vlan tunnel code is handling of vlan-tunid ranges (follows the vlan range handling code). To conserve space vlan-tunid by default are always dumped in ranges if applicable. Use case: example use for this is a vxlan bridging gateway or vtep which maps vlans to vn-segments (or vnis). iproute2 example (patched and pruned iproute2 output to just show relevant fdb entries): example shows same host mac learnt on two vni's and vlan 100 maps to vni 1000, vlan 101 maps to vni 1001 before (netdev per vni): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self after this patch with collect metdata in bridged mode (single netdev): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31 22:59:54 -08:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: per vlan dst_metadata netlink support This patch adds support to attach per vlan tunnel info dst metadata. This enables bridge driver to map vlan to tunnel_info at ingress and egress. It uses the kernel dst_metadata infrastructure. The initial use case is vlan to vni bridging, but the api is generic to extend to any tunnel_info in the future: - Uapi to configure/unconfigure/dump per vlan tunnel data - netlink functions to configure vlan and tunnel_info mapping - Introduces bridge port flag BR_LWT_VLAN to enable attach/detach dst_metadata to bridged packets on ports. off by default. - changes to existing code is mainly refactor some existing vlan handling netlink code + hooks for new vlan tunnel code - I have kept the vlan tunnel code isolated in separate files. - most of the netlink vlan tunnel code is handling of vlan-tunid ranges (follows the vlan range handling code). To conserve space vlan-tunid by default are always dumped in ranges if applicable. Use case: example use for this is a vxlan bridging gateway or vtep which maps vlans to vn-segments (or vnis). iproute2 example (patched and pruned iproute2 output to just show relevant fdb entries): example shows same host mac learnt on two vni's and vlan 100 maps to vni 1000, vlan 101 maps to vni 1001 before (netdev per vni): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self after this patch with collect metdata in bridged mode (single netdev): $bridge fdb show | grep "00:02:00:00:00:03" 00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self 00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge 00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-31 22:59:54 -08:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: Add MAC Authentication Bypass (MAB) support Hosts that support 802.1X authentication are able to authenticate themselves by exchanging EAPOL frames with an authenticator (Ethernet bridge, in this case) and an authentication server. Access to the network is only granted by the authenticator to successfully authenticated hosts. The above is implemented in the bridge using the "locked" bridge port option. When enabled, link-local frames (e.g., EAPOL) can be locally received by the bridge, but all other frames are dropped unless the host is authenticated. That is, unless the user space control plane installed an FDB entry according to which the source address of the frame is located behind the locked ingress port. The entry can be dynamic, in which case learning needs to be enabled so that the entry will be refreshed by incoming traffic. There are deployments in which not all the devices connected to the authenticator (the bridge) support 802.1X. Such devices can include printers and cameras. One option to support such deployments is to unlock the bridge ports connecting these devices, but a slightly more secure option is to use MAB. When MAB is enabled, the MAC address of the connected device is used as the user name and password for the authentication. For MAB to work, the user space control plane needs to be notified about MAC addresses that are trying to gain access so that they will be compared against an allow list. This can be implemented via the regular learning process with the sole difference that learned FDB entries are installed with a new "locked" flag indicating that the entry cannot be used to authenticate the device. The flag cannot be set by user space, but user space can clear the flag by replacing the entry, thereby authenticating the device. Locked FDB entries implement the following semantics with regards to roaming, aging and forwarding: 1. Roaming: Locked FDB entries can roam to unlocked (authorized) ports, in which case the "locked" flag is cleared. FDB entries cannot roam to locked ports regardless of MAB being enabled or not. Therefore, locked FDB entries are only created if an FDB entry with the given {MAC, VID} does not already exist. This behavior prevents unauthenticated devices from disrupting traffic destined to already authenticated devices. 2. Aging: Locked FDB entries age and refresh by incoming traffic like regular entries. 3. Forwarding: Locked FDB entries forward traffic like regular entries. If user space detects an unauthorized MAC behind a locked port and wishes to prevent traffic with this MAC DA from reaching the host, it can do so using tc or a different mechanism. Enable the above behavior using a new bridge port option called "mab". It can only be enabled on a bridge port that is both locked and has learning enabled. Locked FDB entries are flushed from the port once MAB is disabled. A new option is added because there are pure 802.1X deployments that are not interested in notifications about locked FDB entries. Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-11-01 21:39:21 +02:00
net: bridge: Track and limit dynamically learned FDB entries A malicious actor behind one bridge port may spam the kernel with packets with a random source MAC address, each of which will create an FDB entry, each of which is a dynamic allocation in the kernel. There are roughly 2^48 different MAC addresses, further limited by the rhashtable they are stored in to 2^31. Each entry is of the type struct net_bridge_fdb_entry, which is currently 128 bytes big. This means the maximum amount of memory allocated for FDB entries is 2^31 * 128B = 256GiB, which is too much for most computers. Mitigate this by maintaining a per bridge count of those automatically generated entries in fdb_n_learned, and a limit in fdb_max_learned. If the limit is hit new entries are not learned anymore. For backwards compatibility the default setting of 0 disables the limit. User-added entries by netlink or from bridge or bridge port addresses are never blocked and do not count towards that limit. Introduce a new fdb entry flag BR_FDB_DYNAMIC_LEARNED to keep track of whether an FDB entry is included in the count. The flag is enabled for dynamically learned entries, and disabled for all other entries. This should be equivalent to BR_FDB_ADDED_BY_USER and BR_FDB_LOCAL being unset, but contrary to the two flags it can be toggled atomically. Atomicity is required here, as there are multiple callers that modify the flags, but are not under a common lock (br_fdb_update is the exception for br->hash_lock, br_fdb_external_learn_add for RTNL). Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de> Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-2-32cddff87758@avm.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-10-16 15:27:21 +02:00
bridge: fdb: rearrange net_bridge_fdb_entry While looking into fixing the local entries scalability issue I noticed that the structure is badly arranged because vlan_id would fall in a second cache line while keeping rcu which is used only when deleting in the first, so re-arrange the structure and push rcu to the end so we can get 16 bytes which can be used for other fields (by pushing rcu fully in the second 64 byte chunk). With this change all the core necessary information when doing fdb lookups will be available in a single cache line. pahole before (note vlan_id): struct net_bridge_fdb_entry { struct hlist_node hlist; /* 0 16 */ struct net_bridge_port * dst; /* 16 8 */ struct callback_head rcu; /* 24 16 */ long unsigned int updated; /* 40 8 */ long unsigned int used; /* 48 8 */ mac_addr addr; /* 56 6 */ unsigned char is_local:1; /* 62: 7 1 */ unsigned char is_static:1; /* 62: 6 1 */ unsigned char added_by_user:1; /* 62: 5 1 */ unsigned char added_by_external_learn:1; /* 62: 4 1 */ /* XXX 4 bits hole, try to pack */ /* XXX 1 byte hole, try to pack */ /* --- cacheline 1 boundary (64 bytes) --- */ __u16 vlan_id; /* 64 2 */ /* size: 72, cachelines: 2, members: 11 */ /* sum members: 65, holes: 1, sum holes: 1 */ /* bit holes: 1, sum bit holes: 4 bits */ /* padding: 6 */ /* last cacheline: 8 bytes */ } pahole after (note vlan_id): struct net_bridge_fdb_entry { struct hlist_node hlist; /* 0 16 */ struct net_bridge_port * dst; /* 16 8 */ long unsigned int updated; /* 24 8 */ long unsigned int used; /* 32 8 */ mac_addr addr; /* 40 6 */ __u16 vlan_id; /* 46 2 */ unsigned char is_local:1; /* 48: 7 1 */ unsigned char is_static:1; /* 48: 6 1 */ unsigned char added_by_user:1; /* 48: 5 1 */ unsigned char added_by_external_learn:1; /* 48: 4 1 */ /* XXX 4 bits hole, try to pack */ /* XXX 7 bytes hole, try to pack */ struct callback_head rcu; /* 56 16 */ /* --- cacheline 1 boundary (64 bytes) was 8 bytes ago --- */ /* size: 72, cachelines: 2, members: 11 */ /* sum members: 65, holes: 1, sum holes: 7 */ /* bit holes: 1, sum bit holes: 4 bits */ /* last cacheline: 8 bytes */ } Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-27 14:19:20 -07:00
bridge: mcast: Add a flag for user installed source entries There are a few places where the bridge driver differentiates between (S, G) entries installed by the kernel (in response to Membership Reports) and those installed by user space. One of them is when deleting an (S, G) entry corresponding to a source entry that is being deleted. While user space cannot currently add a source entry to a (*, G), it can add an (S, G) entry that later corresponds to a source entry created by the reception of a Membership Report. If this source entry is later deleted because its source timer expired or because the (*, G) entry is being deleted, the bridge driver will not delete the corresponding (S, G) entry if it was added by user space as permanent. This is going to be a problem when the ability to install a (*, G) with a source list is exposed to user space. In this case, when user space installs the (*, G) as permanent, then all the (S, G) entries corresponding to its source list will also be installed as permanent. When user space deletes the (*, G), all the source entries will be deleted and the expectation is that the corresponding (S, G) entries will be deleted as well. Solve this by introducing a new source entry flag denoting that the entry was installed by user space. When the entry is deleted, delete the corresponding (S, G) entry even if it was installed by user space as permanent, as the flag tells us that it was installed in response to the source entry being created. The flag will be set in a subsequent patch where source entries are created in response to user requests. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-10 16:56:26 +02:00
net: bridge: add support for backup port This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which allows to set a backup port to be used for known unicast traffic if the port has gone carrier down. The backup pointer is rcu protected and set only under RTNL, a counter is maintained so when deleting a port we know how many other ports reference it as a backup and we remove it from all. Also the pointer is in the first cache line which is hot at the time of the check and thus in the common case we only add one more test. The backup port will be used only for the non-flooding case since it's a part of the bridge and the flooded packets will be forwarded to it anyway. To remove the forwarding just send a 0/non-existing backup port. This is used to avoid numerous scalability problems when using MLAG most notably if we have thousands of fdbs one would need to change all of them on port carrier going down which takes too long and causes a storm of fdb notifications (and again when the port comes back up). In a Multi-chassis Link Aggregation setup usually hosts are connected to two different switches which act as a single logical switch. Those switches usually have a control and backup link between them called peerlink which might be used for communication in case a host loses connectivity to one of them. We need a fast way to failover in case a host port goes down and currently none of the solutions (like bond) cannot fulfill the requirements because the participating ports are actually the "master" devices and must have the same peerlink as their backup interface and at the same time all of them must participate in the bridge device. As Roopa noted it's normal practice in routing called fast re-route where a precalculated backup path is used when the main one is down. Another use case of this is with EVPN, having a single vxlan device which is backup of every port. Due to the nature of master devices it's not currently possible to use one device as a backup for many and still have all of them participate in the bridge (which is master itself). More detailed information about MLAG is available at the link below. https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG Further explanation and a diagram by Roopa: Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 11:16:59 +03:00
bridge: Add backup nexthop ID support Add a new bridge port attribute that allows attaching a nexthop object ID to an skb that is redirected to a backup bridge port with VLAN tunneling enabled. Specifically, when redirecting a known unicast packet, read the backup nexthop ID from the bridge port that lost its carrier and set it in the bridge control block of the skb before forwarding it via the backup port. Note that reading the ID from the bridge port should not result in a cache miss as the ID is added next to the 'backup_port' field that was already accessed. After this change, the 'state' field still stays on the first cache line, together with other data path related fields such as 'flags and 'vlgrp': struct net_bridge_port { struct net_bridge * br; /* 0 8 */ struct net_device * dev; /* 8 8 */ netdevice_tracker dev_tracker; /* 16 0 */ struct list_head list; /* 16 16 */ long unsigned int flags; /* 32 8 */ struct net_bridge_vlan_group * vlgrp; /* 40 8 */ struct net_bridge_port * backup_port; /* 48 8 */ u32 backup_nhid; /* 56 4 */ u8 priority; /* 60 1 */ u8 state; /* 61 1 */ u16 port_no; /* 62 2 */ /* --- cacheline 1 boundary (64 bytes) --- */ [...] } __attribute__((__aligned__(8))); When forwarding an skb via a bridge port that has VLAN tunneling enabled, check if the backup nexthop ID stored in the bridge control block is valid (i.e., not zero). If so, instead of attaching the pre-allocated metadata (that only has the tunnel key set), allocate a new metadata, set both the tunnel key and the nexthop object ID and attach it to the skb. By default, do not dump the new attribute to user space as a value of zero is an invalid nexthop object ID. The above is useful for EVPN multihoming. When one of the links composing an Ethernet Segment (ES) fails, traffic needs to be redirected towards the host via one of the other ES peers. For example, if a host is multihomed to three different VTEPs, the backup port of each ES link needs to be set to the VXLAN device and the backup nexthop ID needs to point to an FDB nexthop group that includes the IP addresses of the other two VTEPs. The VXLAN driver will extract the ID from the metadata of the redirected skb, calculate its flow hash and forward it towards one of the other VTEPs. If the ID does not exist, or represents an invalid nexthop object, the VXLAN driver will drop the skb. This relieves the bridge driver from the need to validate the ID. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17 11:12:28 +03:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: bridge: disambiguate offload_fwd_mark Before this change, four related - but distinct - concepts where named offload_fwd_mark: - skb->offload_fwd_mark: Set by the switchdev driver if the underlying hardware has already forwarded this frame to the other ports in the same hardware domain. - nbp->offload_fwd_mark: An idetifier used to group ports that share the same hardware forwarding domain. - br->offload_fwd_mark: Counter used to make sure that unique IDs are used in cases where a bridge contains ports from multiple hardware domains. - skb->cb->offload_fwd_mark: The hardware domain on which the frame ingressed and was forwarded. Introduce the term "hardware forwarding domain" ("hwdom") in the bridge to denote a set of ports with the following property: If an skb with skb->offload_fwd_mark set, is received on a port belonging to hwdom N, that frame has already been forwarded to all other ports in hwdom N. By decoupling the name from "offload_fwd_mark", we can extend the term's definition in the future - e.g. to add constraints that describe expected egress behavior - without overloading the meaning of "offload_fwd_mark". - nbp->offload_fwd_mark thus becomes nbp->hwdom. - br->offload_fwd_mark becomes br->last_hwdom. - skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight change in naming here mandates a slight change in behavior of the nbp_switchdev_frame_mark() function. Previously, it only set this value in skb->cb for packets with skb->offload_fwd_mark true (ones which were forwarded in hardware). Whereas now we always track the incoming hwdom for all packets coming from a switchdev (even for the packets which weren't forwarded in hardware, such as STP BPDUs, IGMP reports etc). As all uses of skb->cb->offload_fwd_mark were already gated behind checks of skb->offload_fwd_mark, this will not introduce any functional change, but it paves the way for future changes where the ingressing hwdom must be known for frames coming from a switchdev regardless of whether they were forwarded in hardware or not (basically, if the skb comes from a switchdev, skb->cb->src_hwdom now always tracks which one). A typical example where this is relevant: the switchdev has a fixed configuration to trap STP BPDUs, but STP is not running on the bridge and the group_fwd_mask allows them to be forwarded. Say we have this setup: br0 / | \ / | \ swp0 swp1 swp2 A BPDU comes in on swp0 and is trapped to the CPU; the driver does not set skb->offload_fwd_mark. The bridge determines that the frame should be forwarded to swp{1,2}. It is imperative that forward offloading is _not_ allowed in this case, as the source hwdom is already "poisoned". Recording the source hwdom allows this case to be handled properly. v2->v3: added code comments v3->v6: none Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:23:59 +03:00
net: bridge: switchdev: let drivers inform which bridge ports are offloaded On reception of an skb, the bridge checks if it was marked as 'already forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it is, it assigns the source hardware domain of that skb based on the hardware domain of the ingress port. Then during forwarding, it enforces that the egress port must have a different hardware domain than the ingress one (this is done in nbp_switchdev_allowed_egress). Non-switchdev drivers don't report any physical switch id (neither through devlink nor .ndo_get_port_parent_id), therefore the bridge assigns them a hardware domain of 0, and packets coming from them will always have skb->offload_fwd_mark = 0. So there aren't any restrictions. Problems appear due to the fact that DSA would like to perform software fallback for bonding and team interfaces that the physical switch cannot offload. +-- br0 ---+ / / | \ / / | \ / | | bond0 / | | / \ swp0 swp1 swp2 swp3 swp4 There, it is desirable that the presence of swp3 and swp4 under a non-offloaded LAG does not preclude us from doing hardware bridging beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high enough that software bridging between {swp0,swp1,swp2} and bond0 is not impractical. But this creates an impossible paradox given the current way in which port hardware domains are assigned. When the driver receives a packet from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to something. - If we set it to 0, then the bridge will forward it towards swp1, swp2 and bond0. But the switch has already forwarded it towards swp1 and swp2 (not to bond0, remember, that isn't offloaded, so as far as the switch is concerned, ports swp3 and swp4 are not looking up the FDB, and the entire bond0 is a destination that is strictly behind the CPU). But we don't want duplicated traffic towards swp1 and swp2, so it's not ok to set skb->offload_fwd_mark = 0. - If we set it to 1, then the bridge will not forward the skb towards the ports with the same switchdev mark, i.e. not to swp1, swp2 and bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should have forwarded the skb there. So the real issue is that bond0 will be assigned the same hardware domain as {swp0,swp1,swp2}, because the function that assigns hardware domains to bridge ports, nbp_switchdev_add(), recurses through bond0's lower interfaces until it finds something that implements devlink (calls dev_get_port_parent_id with bool recurse = true). This is a problem because the fact that bond0 can be offloaded by swp3 and swp4 in our example is merely an assumption. A solution is to give the bridge explicit hints as to what hardware domain it should use for each port. Currently, the bridging offload is very 'silent': a driver registers a netdevice notifier, which is put on the netns's notifier chain, and which sniffs around for NETDEV_CHANGEUPPER events where the upper is a bridge, and the lower is an interface it knows about (one registered by this driver, normally). Then, from within that notifier, it does a bunch of stuff behind the bridge's back, without the bridge necessarily knowing that there's somebody offloading that port. It looks like this: ip link set swp0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v call_netdevice_notifiers | v dsa_slave_netdevice_event | v oh, hey! it's for me! | v .port_bridge_join What we do to solve the conundrum is to be less silent, and change the switchdev drivers to present themselves to the bridge. Something like this: ip link set swp0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge: Aye! I'll use this call_netdevice_notifiers ^ ppid as the | | hardware domain for v | this port, and zero dsa_slave_netdevice_event | if I got nothing. | | v | oh, hey! it's for me! | | | v | .port_bridge_join | | | +------------------------+ switchdev_bridge_port_offload(swp0, swp0) Then stacked interfaces (like bond0 on top of swp3/swp4) would be treated differently in DSA, depending on whether we can or cannot offload them. The offload case: ip link set bond0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge: Aye! I'll use this call_netdevice_notifiers ^ ppid as the | | switchdev mark for v | bond0. dsa_slave_netdevice_event | Coincidentally (or not), | | bond0 and swp0, swp1, swp2 v | all have the same switchdev hmm, it's not quite for me, | mark now, since the ASIC but my driver has already | is able to forward towards called .port_lag_join | all these ports in hw. for it, because I have | a port with dp->lag_dev == bond0. | | | v | .port_bridge_join | for swp3 and swp4 | | | +------------------------+ switchdev_bridge_port_offload(bond0, swp3) switchdev_bridge_port_offload(bond0, swp4) And the non-offload case: ip link set bond0 master br0 | v br_add_if() calls netdev_master_upper_dev_link() | v bridge waiting: call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload | | wasn't called, okay, I'll use a v | hwdom of zero for this one. dsa_slave_netdevice_event : Then packets received on swp0 will | : not be software-forwarded towards v : swp1, but they will towards bond0. it's not for me, but bond0 is an upper of swp3 and swp4, but their dp->lag_dev is NULL because they couldn't offload it. Basically we can draw the conclusion that the lowers of a bridge port can come and go, so depending on the configuration of lowers for a bridge port, it can dynamically toggle between offloaded and unoffloaded. Therefore, we need an equivalent switchdev_bridge_port_unoffload too. This patch changes the way any switchdev driver interacts with the bridge. From now on, everybody needs to call switchdev_bridge_port_offload and switchdev_bridge_port_unoffload, otherwise the bridge will treat the port as non-offloaded and allow software flooding to other ports from the same ASIC. Note that these functions lay the ground for a more complex handshake between switchdev drivers and the bridge in the future. For drivers that will request a replay of the switchdev objects when they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we place the call to switchdev_bridge_port_unoffload() strategically inside the NETDEV_PRECHANGEUPPER notifier's code path, and not inside NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers need the netdev adjacency lists to be valid, and that is only true in NETDEV_PRECHANGEUPPER. Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:24:01 +03:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: bridge: add support for backup port This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which allows to set a backup port to be used for known unicast traffic if the port has gone carrier down. The backup pointer is rcu protected and set only under RTNL, a counter is maintained so when deleting a port we know how many other ports reference it as a backup and we remove it from all. Also the pointer is in the first cache line which is hot at the time of the check and thus in the common case we only add one more test. The backup port will be used only for the non-flooding case since it's a part of the bridge and the flooded packets will be forwarded to it anyway. To remove the forwarding just send a 0/non-existing backup port. This is used to avoid numerous scalability problems when using MLAG most notably if we have thousands of fdbs one would need to change all of them on port carrier going down which takes too long and causes a storm of fdb notifications (and again when the port comes back up). In a Multi-chassis Link Aggregation setup usually hosts are connected to two different switches which act as a single logical switch. Those switches usually have a control and backup link between them called peerlink which might be used for communication in case a host loses connectivity to one of them. We need a fast way to failover in case a host port goes down and currently none of the solutions (like bond) cannot fulfill the requirements because the participating ports are actually the "master" devices and must have the same peerlink as their backup interface and at the same time all of them must participate in the bridge device. As Roopa noted it's normal practice in routing called fast re-route where a precalculated backup path is used when the main one is down. Another use case of this is with EVPN, having a single vxlan device which is backup of every port. Due to the nature of master devices it's not currently possible to use one device as a backup for many and still have all of them participate in the bridge (which is master itself). More detailed information about MLAG is available at the link below. https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG Further explanation and a diagram by Roopa: Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 11:16:59 +03:00
bridge: netfilter: Fix forwarding of fragmented packets When netfilter defrag hooks are loaded (due to the presence of conntrack rules, for example), fragmented packets entering the bridge will be defragged by the bridge's pre-routing hook (br_nf_pre_routing() -> ipv4_conntrack_defrag()). Later on, in the bridge's post-routing hook, the defragged packet will be fragmented again. If the size of the largest fragment is larger than what the kernel has determined as the destination MTU (using ip_skb_dst_mtu()), the defragged packet will be dropped. Before commit ac6627a28dbf ("net: ipv4: Consolidate ipv4_mtu and ip_dst_mtu_maybe_forward"), ip_skb_dst_mtu() would return dst_mtu() as the destination MTU. Assuming the dst entry attached to the packet is the bridge's fake rtable one, this would simply be the bridge's MTU (see fake_mtu()). However, after above mentioned commit, ip_skb_dst_mtu() ends up returning the route's MTU stored in the dst entry's metrics. Ideally, in case the dst entry is the bridge's fake rtable one, this should be the bridge's MTU as the bridge takes care of updating this metric when its MTU changes (see br_change_mtu()). Unfortunately, the last operation is a no-op given the metrics attached to the fake rtable entry are marked as read-only. Therefore, ip_skb_dst_mtu() ends up returning 1500 (the initial MTU value) and defragged packets are dropped during fragmentation when dealing with large fragments and high MTU (e.g., 9k). Fix by moving the fake rtable entry's metrics to be per-bridge (in a similar fashion to the fake rtable entry itself) and marking them as writable, thereby allowing MTU changes to be reflected. Fixes: 62fa8a846d7d ("net: Implement read-only protection and COW'ing of metrics.") Fixes: 33eb9873a283 ("bridge: initialize fake_rtable metrics") Reported-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Closes: https://lore.kernel.org/netdev/PH0PR10MB4504888284FF4CBA648197D0ACB82@PH0PR10MB4504.namprd10.prod.outlook.com/ Tested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250515084848.727706-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-15 11:48:48 +03:00
net: bridge: add stp_mode attribute for STP mode selection The bridge-stp usermode helper is currently restricted to the initial network namespace, preventing userspace STP daemons (e.g. mstpd) from operating on bridges in other network namespaces. Since commit ff62198553e4 ("bridge: Only call /sbin/bridge-stp for the initial network namespace"), bridges in non-init namespaces silently fall back to kernel STP with no way to use userspace STP. Add a new bridge attribute IFLA_BR_STP_MODE that allows explicit per-bridge control over STP mode selection: BR_STP_MODE_AUTO (default) - Existing behavior: invoke the /sbin/bridge-stp helper in init_net only; fall back to kernel STP if it fails or in non-init namespaces. BR_STP_MODE_USER - Directly enable userspace STP (BR_USER_STP) without invoking the helper. Works in any network namespace. Userspace is responsible for ensuring an STP daemon manages the bridge. BR_STP_MODE_KERNEL - Directly enable kernel STP (BR_KERNEL_STP) without invoking the helper. The mode can only be changed while STP is disabled, or set to the same value (-EBUSY otherwise). IFLA_BR_STP_MODE is processed before IFLA_BR_STP_STATE in br_changelink(), so both can be set atomically in a single netlink message. The mode can also be changed in the same message that disables STP. The stp_mode struct field is u8 since all possible values fit, while NLA_U32 is used for the netlink attribute since it occupies the same space in the netlink message as NLA_U8. A new stp_helper_active boolean tracks whether the /sbin/bridge-stp helper was invoked during br_stp_start(), so that br_stp_stop() only calls the helper for stop when it was called for start. This avoids calling the helper asymmetrically when stp_mode changes between start and stop. Suggested-by: Ido Schimmel <idosch@nvidia.com> Assisted-by: Claude:claude-opus-4-6 Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Andy Roulin <aroulin@nvidia.com> Link: https://patch.msgid.link/20260405205224.3163000-2-aroulin@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-04-05 13:52:22 -07:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: bridge: Track and limit dynamically learned FDB entries A malicious actor behind one bridge port may spam the kernel with packets with a random source MAC address, each of which will create an FDB entry, each of which is a dynamic allocation in the kernel. There are roughly 2^48 different MAC addresses, further limited by the rhashtable they are stored in to 2^31. Each entry is of the type struct net_bridge_fdb_entry, which is currently 128 bytes big. This means the maximum amount of memory allocated for FDB entries is 2^31 * 128B = 256GiB, which is too much for most computers. Mitigate this by maintaining a per bridge count of those automatically generated entries in fdb_n_learned, and a limit in fdb_max_learned. If the limit is hit new entries are not learned anymore. For backwards compatibility the default setting of 0 disables the limit. User-added entries by netlink or from bridge or bridge port addresses are never blocked and do not count towards that limit. Introduce a new fdb entry flag BR_FDB_DYNAMIC_LEARNED to keep track of whether an FDB entry is included in the count. The flag is enabled for dynamically learned entries, and disabled for all other entries. This should be equivalent to BR_FDB_ADDED_BY_USER and BR_FDB_LOCAL being unset, but contrary to the two flags it can be toggled atomically. Atomicity is required here, as there are multiple callers that modify the flags, but are not under a common lock (br_fdb_update is the exception for br->hash_lock, br_fdb_external_learn_add for RTNL). Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Johannes Nixdorf <jnixdorf-oss@avm.de> Link: https://lore.kernel.org/r/20231016-fdb_limit-v5-2-32cddff87758@avm.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-10-16 15:27:21 +02:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: bridge: disambiguate offload_fwd_mark Before this change, four related - but distinct - concepts where named offload_fwd_mark: - skb->offload_fwd_mark: Set by the switchdev driver if the underlying hardware has already forwarded this frame to the other ports in the same hardware domain. - nbp->offload_fwd_mark: An idetifier used to group ports that share the same hardware forwarding domain. - br->offload_fwd_mark: Counter used to make sure that unique IDs are used in cases where a bridge contains ports from multiple hardware domains. - skb->cb->offload_fwd_mark: The hardware domain on which the frame ingressed and was forwarded. Introduce the term "hardware forwarding domain" ("hwdom") in the bridge to denote a set of ports with the following property: If an skb with skb->offload_fwd_mark set, is received on a port belonging to hwdom N, that frame has already been forwarded to all other ports in hwdom N. By decoupling the name from "offload_fwd_mark", we can extend the term's definition in the future - e.g. to add constraints that describe expected egress behavior - without overloading the meaning of "offload_fwd_mark". - nbp->offload_fwd_mark thus becomes nbp->hwdom. - br->offload_fwd_mark becomes br->last_hwdom. - skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight change in naming here mandates a slight change in behavior of the nbp_switchdev_frame_mark() function. Previously, it only set this value in skb->cb for packets with skb->offload_fwd_mark true (ones which were forwarded in hardware). Whereas now we always track the incoming hwdom for all packets coming from a switchdev (even for the packets which weren't forwarded in hardware, such as STP BPDUs, IGMP reports etc). As all uses of skb->cb->offload_fwd_mark were already gated behind checks of skb->offload_fwd_mark, this will not introduce any functional change, but it paves the way for future changes where the ingressing hwdom must be known for frames coming from a switchdev regardless of whether they were forwarded in hardware or not (basically, if the skb comes from a switchdev, skb->cb->src_hwdom now always tracks which one). A typical example where this is relevant: the switchdev has a fixed configuration to trap STP BPDUs, but STP is not running on the bridge and the group_fwd_mask allows them to be forwarded. Say we have this setup: br0 / | \ / | \ swp0 swp1 swp2 A BPDU comes in on swp0 and is trapped to the CPU; the driver does not set skb->offload_fwd_mark. The bridge determines that the frame should be forwarded to swp{1,2}. It is imperative that forward offloading is _not_ allowed in this case, as the source hwdom is already "poisoned". Recording the source hwdom allows this case to be handled properly. v2->v3: added code comments v3->v6: none Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:23:59 +03:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
netfilter: bridge: add connection tracking system This patch adds basic connection tracking support for the bridge, including initial IPv4 support. This patch register two hooks to deal with the bridge forwarding path, one from the bridge prerouting hook to call nf_conntrack_in(); and another from the bridge postrouting hook to confirm the entry. The conntrack bridge prerouting hook defragments packets before passing them to nf_conntrack_in() to look up for an existing entry, otherwise a new entry is allocated and it is attached to the skbuff. The conntrack bridge postrouting hook confirms new conntrack entries, ie. if this is the first packet seen, then it adds the entry to the hashtable and (if needed) it refragments the skbuff into the original fragments, leaving the geometry as is if possible. Exceptions are linearized skbuffs, eg. skbuffs that are passed up to nfqueue and conntrack helpers, as well as cloned skbuff for the local delivery (eg. tcpdump), also in case of bridge port flooding (cloned skbuff too). The packet defragmentation is done through the ip_defrag() call. This forces us to save the bridge control buffer, reset the IP control buffer area and then restore it after call. This function also bumps the IP fragmentation statistics, it would be probably desiderable to have independent statistics for the bridge defragmentation/refragmentation. The maximum fragment length is stored in the control buffer and it is used to refragment the skbuff from the postrouting path. The new fraglist splitter and fragment transformer APIs are used to implement the bridge refragmentation code. The br_ip_fragment() function drops the packet in case the maximum fragment size seen is larger than the output port MTU. This patchset follows the principle that conntrack should not drop packets, so users can do it through policy via invalid state matching. Like br_netfilter, there is no refragmentation for packets that are passed up for local delivery, ie. prerouting -> input path. There are calls to nf_reset() already in several spots in the stack since time ago already, eg. af_packet, that show that skbuff fraglist handling from the netif_rx path is supported already. The helpers are called from the postrouting hook, before confirmation, from there we may see packet floods to bridge ports. Then, although unlikely, this may result in exercising the helpers many times for each clone. It would be good to explore how to pass all the packets in a list to the conntrack hook to do this handle only once for this case. Thanks to Florian Westphal for handing me over an initial patchset version to add support for conntrack bridge. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-29 13:25:37 +02:00
netfilter: br_netfilter: skip conntrack input hook for promisc packets For historical reasons, when bridge device is in promisc mode, packets that are directed to the taps follow bridge input hook path. This patch adds a workaround to reset conntrack for these packets. Jianbo Liu reports warning splats in their test infrastructure where cloned packets reach the br_netfilter input hook to confirm the conntrack object. Scratch one bit from BR_INPUT_SKB_CB to annotate that this packet has reached the input hook because it is passed up to the bridge device to reach the taps. [ 57.571874] WARNING: CPU: 1 PID: 0 at net/bridge/br_netfilter_hooks.c:616 br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.572749] Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_isc si ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5ctl mlx5_core [ 57.575158] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.8.0+ #19 [ 57.575700] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 57.576662] RIP: 0010:br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.577195] Code: fe ff ff 41 bd 04 00 00 00 be 04 00 00 00 e9 4a ff ff ff be 04 00 00 00 48 89 ef e8 f3 a9 3c e1 66 83 ad b4 00 00 00 04 eb 91 <0f> 0b e9 f1 fe ff ff 0f 0b e9 df fe ff ff 48 89 df e8 b3 53 47 e1 [ 57.578722] RSP: 0018:ffff88885f845a08 EFLAGS: 00010202 [ 57.579207] RAX: 0000000000000002 RBX: ffff88812dfe8000 RCX: 0000000000000000 [ 57.579830] RDX: ffff88885f845a60 RSI: ffff8881022dc300 RDI: 0000000000000000 [ 57.580454] RBP: ffff88885f845a60 R08: 0000000000000001 R09: 0000000000000003 [ 57.581076] R10: 00000000ffff1300 R11: 0000000000000002 R12: 0000000000000000 [ 57.581695] R13: ffff8881047ffe00 R14: ffff888108dbee00 R15: ffff88814519b800 [ 57.582313] FS: 0000000000000000(0000) GS:ffff88885f840000(0000) knlGS:0000000000000000 [ 57.583040] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.583564] CR2: 000000c4206aa000 CR3: 0000000103847001 CR4: 0000000000370eb0 [ 57.584194] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.584820] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.585440] Call Trace: [ 57.585721] <IRQ> [ 57.585976] ? __warn+0x7d/0x130 [ 57.586323] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.586811] ? report_bug+0xf1/0x1c0 [ 57.587177] ? handle_bug+0x3f/0x70 [ 57.587539] ? exc_invalid_op+0x13/0x60 [ 57.587929] ? asm_exc_invalid_op+0x16/0x20 [ 57.588336] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.588825] nf_hook_slow+0x3d/0xd0 [ 57.589188] ? br_handle_vlan+0x4b/0x110 [ 57.589579] br_pass_frame_up+0xfc/0x150 [ 57.589970] ? br_port_flags_change+0x40/0x40 [ 57.590396] br_handle_frame_finish+0x346/0x5e0 [ 57.590837] ? ipt_do_table+0x32e/0x430 [ 57.591221] ? br_handle_local_finish+0x20/0x20 [ 57.591656] br_nf_hook_thresh+0x4b/0xf0 [br_netfilter] [ 57.592286] ? br_handle_local_finish+0x20/0x20 [ 57.592802] br_nf_pre_routing_finish+0x178/0x480 [br_netfilter] [ 57.593348] ? br_handle_local_finish+0x20/0x20 [ 57.593782] ? nf_nat_ipv4_pre_routing+0x25/0x60 [nf_nat] [ 57.594279] br_nf_pre_routing+0x24c/0x550 [br_netfilter] [ 57.594780] ? br_nf_hook_thresh+0xf0/0xf0 [br_netfilter] [ 57.595280] br_handle_frame+0x1f3/0x3d0 [ 57.595676] ? br_handle_local_finish+0x20/0x20 [ 57.596118] ? br_handle_frame_finish+0x5e0/0x5e0 [ 57.596566] __netif_receive_skb_core+0x25b/0xfc0 [ 57.597017] ? __napi_build_skb+0x37/0x40 [ 57.597418] __netif_receive_skb_list_core+0xfb/0x220 Fixes: 62e7151ae3eb ("netfilter: bridge: confirm multicast packets before passing them up the stack") Reported-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2024-04-09 11:24:59 +02:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22 18:55:38 +03:00
net: bridge: disambiguate offload_fwd_mark Before this change, four related - but distinct - concepts where named offload_fwd_mark: - skb->offload_fwd_mark: Set by the switchdev driver if the underlying hardware has already forwarded this frame to the other ports in the same hardware domain. - nbp->offload_fwd_mark: An idetifier used to group ports that share the same hardware forwarding domain. - br->offload_fwd_mark: Counter used to make sure that unique IDs are used in cases where a bridge contains ports from multiple hardware domains. - skb->cb->offload_fwd_mark: The hardware domain on which the frame ingressed and was forwarded. Introduce the term "hardware forwarding domain" ("hwdom") in the bridge to denote a set of ports with the following property: If an skb with skb->offload_fwd_mark set, is received on a port belonging to hwdom N, that frame has already been forwarded to all other ports in hwdom N. By decoupling the name from "offload_fwd_mark", we can extend the term's definition in the future - e.g. to add constraints that describe expected egress behavior - without overloading the meaning of "offload_fwd_mark". - nbp->offload_fwd_mark thus becomes nbp->hwdom. - br->offload_fwd_mark becomes br->last_hwdom. - skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight change in naming here mandates a slight change in behavior of the nbp_switchdev_frame_mark() function. Previously, it only set this value in skb->cb for packets with skb->offload_fwd_mark true (ones which were forwarded in hardware). Whereas now we always track the incoming hwdom for all packets coming from a switchdev (even for the packets which weren't forwarded in hardware, such as STP BPDUs, IGMP reports etc). As all uses of skb->cb->offload_fwd_mark were already gated behind checks of skb->offload_fwd_mark, this will not introduce any functional change, but it paves the way for future changes where the ingressing hwdom must be known for frames coming from a switchdev regardless of whether they were forwarded in hardware or not (basically, if the skb comes from a switchdev, skb->cb->src_hwdom now always tracks which one). A typical example where this is relevant: the switchdev has a fixed configuration to trap STP BPDUs, but STP is not running on the bridge and the group_fwd_mask allows them to be forwarded. Say we have this setup: br0 / | \ / | \ swp0 swp1 swp2 A BPDU comes in on swp0 and is trapped to the CPU; the driver does not set skb->offload_fwd_mark. The bridge determines that the frame should be forwarded to swp{1,2}. It is imperative that forward offloading is _not_ allowed in this case, as the source hwdom is already "poisoned". Recording the source hwdom allows this case to be handled properly. v2->v3: added code comments v3->v6: none Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:23:59 +03:00
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22 18:55:38 +03:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
bridge: Add backup nexthop ID support Add a new bridge port attribute that allows attaching a nexthop object ID to an skb that is redirected to a backup bridge port with VLAN tunneling enabled. Specifically, when redirecting a known unicast packet, read the backup nexthop ID from the bridge port that lost its carrier and set it in the bridge control block of the skb before forwarding it via the backup port. Note that reading the ID from the bridge port should not result in a cache miss as the ID is added next to the 'backup_port' field that was already accessed. After this change, the 'state' field still stays on the first cache line, together with other data path related fields such as 'flags and 'vlgrp': struct net_bridge_port { struct net_bridge * br; /* 0 8 */ struct net_device * dev; /* 8 8 */ netdevice_tracker dev_tracker; /* 16 0 */ struct list_head list; /* 16 16 */ long unsigned int flags; /* 32 8 */ struct net_bridge_vlan_group * vlgrp; /* 40 8 */ struct net_bridge_port * backup_port; /* 48 8 */ u32 backup_nhid; /* 56 4 */ u8 priority; /* 60 1 */ u8 state; /* 61 1 */ u16 port_no; /* 62 2 */ /* --- cacheline 1 boundary (64 bytes) --- */ [...] } __attribute__((__aligned__(8))); When forwarding an skb via a bridge port that has VLAN tunneling enabled, check if the backup nexthop ID stored in the bridge control block is valid (i.e., not zero). If so, instead of attaching the pre-allocated metadata (that only has the tunnel key set), allocate a new metadata, set both the tunnel key and the nexthop object ID and attach it to the skb. By default, do not dump the new attribute to user space as a value of zero is an invalid nexthop object ID. The above is useful for EVPN multihoming. When one of the links composing an Ethernet Segment (ES) fails, traffic needs to be redirected towards the host via one of the other ES peers. For example, if a host is multihomed to three different VTEPs, the backup port of each ES link needs to be set to the VXLAN device and the backup nexthop ID needs to point to an FDB nexthop group that includes the IP addresses of the other two VTEPs. The VXLAN driver will extract the ID from the metadata of the redirected skb, calculate its flow hash and forward it towards one of the other VTEPs. If the ID does not exist, or represents an invalid nexthop object, the VXLAN driver will drop the skb. This relieves the bridge driver from the need to validate the ID. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-17 11:12:28 +03:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
net: bridge: add support for user-controlled bool options We have been adding many new bridge options, a big number of which are boolean but still take up netlink attribute ids and waste space in the skb. Recently we discussed learning from link-local packets[1] and decided yet another new boolean option will be needed, thus introducing this API to save some bridge nl space. The API supports changing the value of multiple boolean options at once via the br_boolopt_multi struct which has an optmask (which options to set, bit per opt) and optval (options' new values). Future boolean options will only be added to the br_boolopt_id enum and then will have to be handled in br_boolopt_toggle/get. The API will automatically add the ability to change and export them via netlink, sysfs can use the single boolopt function versions to do the same. The behaviour with failing/succeeding is the same as with normal netlink option changing. If an option requires mapping to internal kernel flag or needs special configuration to be enabled then it should be handled in br_boolopt_toggle. It should also be able to retrieve an option's current state via br_boolopt_get. v2: WARN_ON() on unsupported option as that shouldn't be possible and also will help catch people who add new options without handling them for both set and get. Pass down extack so if an option desires it could set it on error and be more user-friendly. [1] https://www.spinics.net/lists/netdev/msg532698.html Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-24 04:34:20 +02:00
skbuff: bridge: Add layer 2 miss indication For EVPN non-DF (Designated Forwarder) filtering we need to be able to prevent decapsulated traffic from being flooded to a multi-homed host. Filtering of multicast and broadcast traffic can be achieved using the following flower filter: # tc filter add dev bond0 egress pref 1 proto all flower indev vxlan0 dst_mac 01:00:00:00:00:00/01:00:00:00:00:00 action drop Unlike broadcast and multicast traffic, it is not currently possible to filter unknown unicast traffic. The classification into unknown unicast is performed by the bridge driver, but is not visible to other layers such as tc. Solve this by adding a new 'l2_miss' bit to the tc skb extension. Clear the bit whenever a packet enters the bridge (received from a bridge port or transmitted via the bridge) and set it if the packet did not match an FDB or MDB entry. If there is no skb extension and the bit needs to be cleared, then do not allocate one as no extension is equivalent to the bit being cleared. The bit is not set for broadcast packets as they never perform a lookup and therefore never incur a miss. A bit that is set for every flooded packet would also work for the current use case, but it does not allow us to differentiate between registered and unregistered multicast traffic, which might be useful in the future. To keep the performance impact to a minimum, the marking of packets is guarded by the 'tc_skb_ext_tc' static key. When 'false', the skb is not touched and an skb extension is not allocated. Instead, only a 5 bytes nop is executed, as demonstrated below for the call site in br_handle_frame(). Before the patch: ``` memset(skb->cb, 0, sizeof(struct br_input_skb_cb)); c37b09: 49 c7 44 24 28 00 00 movq $0x0,0x28(%r12) c37b10: 00 00 p = br_port_get_rcu(skb->dev); c37b12: 49 8b 44 24 10 mov 0x10(%r12),%rax memset(skb->cb, 0, sizeof(struct br_input_skb_cb)); c37b17: 49 c7 44 24 30 00 00 movq $0x0,0x30(%r12) c37b1e: 00 00 c37b20: 49 c7 44 24 38 00 00 movq $0x0,0x38(%r12) c37b27: 00 00 ``` After the patch (when static key is disabled): ``` memset(skb->cb, 0, sizeof(struct br_input_skb_cb)); c37c29: 49 c7 44 24 28 00 00 movq $0x0,0x28(%r12) c37c30: 00 00 c37c32: 49 8d 44 24 28 lea 0x28(%r12),%rax c37c37: 48 c7 40 08 00 00 00 movq $0x0,0x8(%rax) c37c3e: 00 c37c3f: 48 c7 40 10 00 00 00 movq $0x0,0x10(%rax) c37c46: 00 #ifdef CONFIG_HAVE_JUMP_LABEL_HACK static __always_inline bool arch_static_branch(struct static_key *key, bool branch) { asm_volatile_goto("1:" c37c47: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1) br_tc_skb_miss_set(skb, false); p = br_port_get_rcu(skb->dev); c37c4c: 49 8b 44 24 10 mov 0x10(%r12),%rax ``` Subsequent patches will extend the flower classifier to be able to match on the new 'l2_miss' bit and enable / disable the static key when filters that match on it are added / deleted. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-05-29 14:48:28 +03:00
netpoll: Remove gfp parameter from __netpoll_setup The gfp parameter was added in: commit 47be03a28cc6c80e3aa2b3e8ed6d960ff0c5c0af Author: Amerigo Wang <amwang@redhat.com> Date: Fri Aug 10 01:24:37 2012 +0000 netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup() slave_enable_netpoll() and __netpoll_setup() may be called with read_lock() held, so should use GFP_ATOMIC to allocate memory. Eric suggested to pass gfp flags to __netpoll_setup(). Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> The reason for the gfp parameter was removed in: commit c4cdef9b7183159c23c7302aaf270d64c549f557 Author: dingtianhong <dingtianhong@huawei.com> Date: Tue Jul 23 15:25:27 2013 +0800 bonding: don't call slave_xxx_netpoll under spinlocks The slave_xxx_netpoll will call synchronize_rcu_bh(), so the function may schedule and sleep, it should't be called under spinlocks. bond_netpoll_setup() and bond_netpoll_cleanup() are always protected by rtnl lock, it is no need to take the read lock, as the slave list couldn't be changed outside rtnl lock. Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Nothing else that calls __netpoll_setup or ndo_netpoll_setup requires a gfp paramter, so remove the gfp parameter from both of these functions making the code clearer. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-27 15:36:38 -07:00
netpoll: Remove gfp parameter from __netpoll_setup The gfp parameter was added in: commit 47be03a28cc6c80e3aa2b3e8ed6d960ff0c5c0af Author: Amerigo Wang <amwang@redhat.com> Date: Fri Aug 10 01:24:37 2012 +0000 netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup() slave_enable_netpoll() and __netpoll_setup() may be called with read_lock() held, so should use GFP_ATOMIC to allocate memory. Eric suggested to pass gfp flags to __netpoll_setup(). Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> The reason for the gfp parameter was removed in: commit c4cdef9b7183159c23c7302aaf270d64c549f557 Author: dingtianhong <dingtianhong@huawei.com> Date: Tue Jul 23 15:25:27 2013 +0800 bonding: don't call slave_xxx_netpoll under spinlocks The slave_xxx_netpoll will call synchronize_rcu_bh(), so the function may schedule and sleep, it should't be called under spinlocks. bond_netpoll_setup() and bond_netpoll_cleanup() are always protected by rtnl lock, it is no need to take the read lock, as the slave list couldn't be changed outside rtnl lock. Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Nothing else that calls __netpoll_setup or ndo_netpoll_setup requires a gfp paramter, so remove the gfp parameter from both of these functions making the code clearer. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-27 15:36:38 -07:00
net: add generic PF_BRIDGE:RTM_ FDB hooks This adds two new flags NTF_MASTER and NTF_SELF that can now be used to specify where PF_BRIDGE netlink commands should be sent. NTF_MASTER sends the commands to the 'dev->master' device for parsing. Typically this will be the linux net/bridge, or open-vswitch devices. Also without any flags set the command will be handled by the master device as well so that current user space tools continue to work as expected. The NTF_SELF flag will push the PF_BRIDGE commands to the device. In the basic example below the commands are then parsed and programmed in the embedded bridge. Note if both NTF_SELF and NTF_MASTER bits are set then the command will be sent to both 'dev->master' and 'dev' this allows user space to easily keep the embedded bridge and software bridge in sync. There is a slight complication in the case with both flags set when an error occurs. To resolve this the rtnl handler clears the NTF_ flag in the netlink ack to indicate which sets completed successfully. The add/del handlers will abort as soon as any error occurs. To support this new net device ops were added to call into the device and the existing bridging code was refactored to use these. There should be no required changes in user space to support the current bridge behavior. A basic setup with a SR-IOV enabled NIC looks like this, veth0 veth2 | | ------------ | bridge0 | <---- software bridging ------------ / / ethx.y ethx VF PF \ \ <---- propagate FDB entries to HW \ \ -------------------- | Embedded Bridge | <---- hardware offloaded switching -------------------- In this case the embedded bridge must be managed to allow 'veth0' to communicate with 'ethx.y' correctly. At present drivers managing the embedded bridge either send frames onto the network which then get dropped by the switch OR the embedded bridge will flood these frames. With this patch we have a mechanism to manage the embedded bridge correctly from user space. This example is specific to SR-IOV but replacing the VF with another PF or dropping this into the DSA framework generates similar management issues. Examples session using the 'br'[1] tool to add, dump and then delete a mac address with a new "embedded" option and enabled ixgbe driver: # br fdb add 22:35:19:ac:60:59 dev eth3 # br fdb port mac addr flags veth0 22:35:19:ac:60:58 static veth0 9a:5f:81:f7:f6:ec local eth3 00:1b:21:55:23:59 local eth3 22:35:19:ac:60:59 static veth0 22:35:19:ac:60:57 static #br fdb add 22:35:19:ac:60:59 embedded dev eth3 #br fdb port mac addr flags veth0 22:35:19:ac:60:58 static veth0 9a:5f:81:f7:f6:ec local eth3 00:1b:21:55:23:59 local eth3 22:35:19:ac:60:59 static veth0 22:35:19:ac:60:57 static eth3 22:35:19:ac:60:59 local embedded #br fdb del 22:35:19:ac:60:59 embedded dev eth3 I added a couple lines to 'br' to set the flags correctly is all. It is my opinion that the merit of this patch is now embedded and SW bridges can both be modeled correctly in user space using very nearly the same message passing. [1] 'br' tool was published as an RFC here and will be renamed 'bridge' http://patchwork.ozlabs.org/patch/117664/ Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for valuable feedback, suggestions, and review. v2: fixed api descriptions and error case with both NTF_SELF and NTF_MASTER set plus updated patch description. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15 06:43:56 +00:00
rtnetlink: fdb dump: optimize by saving last interface markers fdb dumps spanning multiple skb's currently restart from the first interface again for every skb. This results in unnecessary iterations on the already visited interfaces and their fdb entries. In large scale setups, we have seen this to slow down fdb dumps considerably. On a system with 30k macs we see fdb dumps spanning across more than 300 skbs. To fix the problem, this patch replaces the existing single fdb marker with three markers: netdev hash entries, netdevs and fdb index to continue where we left off instead of restarting from the first netdev. This is consistent with link dumps. In the process of fixing the performance issue, this patch also re-implements fix done by commit 472681d57a5d ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump") (with an internal fix from Wilson Kok) in the following ways: - change ndo_fdb_dump handlers to return error code instead of the last fdb index - use cb->args strictly for dump frag markers and not error codes. This is consistent with other dump functions. Below results were taken on a system with 1000 netdevs and 35085 fdb entries: before patch: $time bridge fdb show | wc -l 15065 real 1m11.791s user 0m0.070s sys 1m8.395s (existing code does not return all macs) after patch: $time bridge fdb show | wc -l 35085 real 0m2.017s user 0m0.113s sys 0m1.942s Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-30 21:56:45 -07:00
bridge: switchdev: Allow device drivers to install locked FDB entries When the bridge is offloaded to hardware, FDB entries are learned and aged-out by the hardware. Some device drivers synchronize the hardware and software FDBs by generating switchdev events towards the bridge. When a port is locked, the hardware must not learn autonomously, as otherwise any host will blindly gain authorization. Instead, the hardware should generate events regarding hosts that are trying to gain authorization and their MAC addresses should be notified by the device driver as locked FDB entries towards the bridge driver. Allow device drivers to notify the bridge driver about such entries by extending the 'switchdev_notifier_fdb_info' structure with the 'locked' bit. The bit can only be set by device drivers and not by the bridge driver. Prevent a locked entry from being installed if MAB is not enabled on the bridge port. If an entry already exists in the bridge driver, reject the locked entry if the current entry does not have the "locked" flag set or if it points to a different port. The same semantics are implemented in the software data path. Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-11-08 11:47:08 +01:00
bridge: Automatically manage port promiscuous mode. There exist configurations where the administrator or another management entity has the foreknowledge of all the mac addresses of end systems that are being bridged together. In these environments, the administrator can statically configure known addresses in the bridge FDB and disable flooding and learning on ports. This makes it possible to turn off promiscuous mode on the interfaces connected to the bridge. Here is why disabling flooding and learning allows us to control promiscuity: Consider port X. All traffic coming into this port from outside the bridge (ingress) will be either forwarded through other ports of the bridge (egress) or dropped. Forwarding (egress) is defined by FDB entries and by flooding in the event that no FDB entry exists. In the event that flooding is disabled, only FDB entries define the egress. Once learning is disabled, only static FDB entries provided by a management entity define the egress. If we provide information from these static FDBs to the ingress port X, then we'll be able to accept all traffic that can be successfully forwarded and drop all the other traffic sooner without spending CPU cycles to process it. Another way to define the above is as following equations: ingress = egress + drop expanding egress ingress = static FDB + learned FDB + flooding + drop disabling flooding and learning we a left with ingress = static FDB + drop By adding addresses from the static FDB entries to the MAC address filter of an ingress port X, we fully define what the bridge can process without dropping and can thus turn off promiscuous mode, thus dropping packets sooner. There have been suggestions that we may want to allow learning and update the filters with learned addresses as well. This would require mac-level authentication similar to 802.1x to prevent attacks against the hw filters as they are limited resource. Additionally, if the user places the bridge device in promiscuous mode, all ports are placed in promiscuous mode regardless of the changes to flooding and learning. Since the above functionality depends on full static configuration, we have also require that vlan filtering be enabled to take advantage of this. The reason is that the bridge has to be able to receive and process VLAN-tagged frames and the there are only 2 ways to accomplish this right now: promiscuous mode or vlan filtering. Suggested-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 09:59:20 -04:00
net: bridge: add support for backup port This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which allows to set a backup port to be used for known unicast traffic if the port has gone carrier down. The backup pointer is rcu protected and set only under RTNL, a counter is maintained so when deleting a port we know how many other ports reference it as a backup and we remove it from all. Also the pointer is in the first cache line which is hot at the time of the check and thus in the common case we only add one more test. The backup port will be used only for the non-flooding case since it's a part of the bridge and the flooded packets will be forwarded to it anyway. To remove the forwarding just send a 0/non-existing backup port. This is used to avoid numerous scalability problems when using MLAG most notably if we have thousands of fdbs one would need to change all of them on port carrier going down which takes too long and causes a storm of fdb notifications (and again when the port comes back up). In a Multi-chassis Link Aggregation setup usually hosts are connected to two different switches which act as a single logical switch. Those switches usually have a control and backup link between them called peerlink which might be used for communication in case a host loses connectivity to one of them. We need a fast way to failover in case a host port goes down and currently none of the solutions (like bond) cannot fulfill the requirements because the participating ports are actually the "master" devices and must have the same peerlink as their backup interface and at the same time all of them must participate in the bridge device. As Roopa noted it's normal practice in routing called fast re-route where a precalculated backup path is used when the main one is down. Another use case of this is with EVPN, having a single vxlan device which is backup of every port. Due to the nature of master devices it's not currently possible to use one device as a backup for many and still have all of them participate in the bridge (which is master itself). More detailed information about MLAG is available at the link below. https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG Further explanation and a diagram by Roopa: Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 11:16:59 +03:00
net: bridge: allow enslaving some DSA master network devices Commit 8db0a2ee2c63 ("net: bridge: reject DSA-enabled master netdevices as bridge members") added a special check in br_if.c in order to check for a DSA master network device with a tagging protocol configured. This was done because back then, such devices, once enslaved in a bridge would become inoperative and would not pass DSA tagged traffic anymore due to br_handle_frame returning RX_HANDLER_CONSUMED. But right now we have valid use cases which do require bridging of DSA masters. One such example is when the DSA master ports are DSA switch ports themselves (in a disjoint tree setup). This should be completely equivalent, functionally speaking, from having multiple DSA switches hanging off of the ports of a switchdev driver. So we should allow the enslaving of DSA tagged master network devices. Instead of the regular br_handle_frame(), install a new function br_handle_frame_dummy() on these DSA masters, which returns RX_HANDLER_PASS in order to call into the DSA specific tagging protocol handlers, and lift the restriction from br_add_if. Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-05-10 19:37:40 +03:00
net: bridge: allow enslaving some DSA master network devices Commit 8db0a2ee2c63 ("net: bridge: reject DSA-enabled master netdevices as bridge members") added a special check in br_if.c in order to check for a DSA master network device with a tagging protocol configured. This was done because back then, such devices, once enslaved in a bridge would become inoperative and would not pass DSA tagged traffic anymore due to br_handle_frame returning RX_HANDLER_CONSUMED. But right now we have valid use cases which do require bridging of DSA masters. One such example is when the DSA master ports are DSA switch ports themselves (in a disjoint tree setup). This should be completely equivalent, functionally speaking, from having multiple DSA switches hanging off of the ports of a switchdev driver. So we should allow the enslaving of DSA tagged master network devices. Instead of the regular br_handle_frame(), install a new function br_handle_frame_dummy() on these DSA masters, which returns RX_HANDLER_PASS in order to call into the DSA specific tagging protocol handlers, and lift the restriction from br_add_if. Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-05-10 19:37:40 +03:00
net: bridge: allow enslaving some DSA master network devices Commit 8db0a2ee2c63 ("net: bridge: reject DSA-enabled master netdevices as bridge members") added a special check in br_if.c in order to check for a DSA master network device with a tagging protocol configured. This was done because back then, such devices, once enslaved in a bridge would become inoperative and would not pass DSA tagged traffic anymore due to br_handle_frame returning RX_HANDLER_CONSUMED. But right now we have valid use cases which do require bridging of DSA masters. One such example is when the DSA master ports are DSA switch ports themselves (in a disjoint tree setup). This should be completely equivalent, functionally speaking, from having multiple DSA switches hanging off of the ports of a switchdev driver. So we should allow the enslaving of DSA tagged master network devices. Instead of the regular br_handle_frame(), install a new function br_handle_frame_dummy() on these DSA masters, which returns RX_HANDLER_PASS in order to call into the DSA specific tagging protocol handlers, and lift the restriction from br_add_if. Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-05-10 19:37:40 +03:00
net: Remove RTNL dance for SIOCBRADDIF and SIOCBRDELIF. SIOCBRDELIF is passed to dev_ioctl() first and later forwarded to br_ioctl_call(), which causes unnecessary RTNL dance and the splat below [0] under RTNL pressure. Let's say Thread A is trying to detach a device from a bridge and Thread B is trying to remove the bridge. In dev_ioctl(), Thread A bumps the bridge device's refcnt by netdev_hold() and releases RTNL because the following br_ioctl_call() also re-acquires RTNL. In the race window, Thread B could acquire RTNL and try to remove the bridge device. Then, rtnl_unlock() by Thread B will release RTNL and wait for netdev_put() by Thread A. Thread A, however, must hold RTNL after the unlock in dev_ifsioc(), which may take long under RTNL pressure, resulting in the splat by Thread B. Thread A (SIOCBRDELIF) Thread B (SIOCBRDELBR) ---------------------- ---------------------- sock_ioctl sock_ioctl `- sock_do_ioctl `- br_ioctl_call `- dev_ioctl `- br_ioctl_stub |- rtnl_lock | |- dev_ifsioc ' ' |- dev = __dev_get_by_name(...) |- netdev_hold(dev, ...) . / |- rtnl_unlock ------. | | |- br_ioctl_call `---> |- rtnl_lock Race | | `- br_ioctl_stub |- br_del_bridge Window | | | |- dev = __dev_get_by_name(...) | | | May take long | `- br_dev_delete(dev, ...) | | | under RTNL pressure | `- unregister_netdevice_queue(dev, ...) | | | | `- rtnl_unlock \ | |- rtnl_lock <-' `- netdev_run_todo | |- ... `- netdev_run_todo | `- rtnl_unlock |- __rtnl_unlock | |- netdev_wait_allrefs_any |- netdev_put(dev, ...) <----------------' Wait refcnt decrement and log splat below To avoid blocking SIOCBRDELBR unnecessarily, let's not call dev_ioctl() for SIOCBRADDIF and SIOCBRDELIF. In the dev_ioctl() path, we do the following: 1. Copy struct ifreq by get_user_ifreq in sock_do_ioctl() 2. Check CAP_NET_ADMIN in dev_ioctl() 3. Call dev_load() in dev_ioctl() 4. Fetch the master dev from ifr.ifr_name in dev_ifsioc() 3. can be done by request_module() in br_ioctl_call(), so we move 1., 2., and 4. to br_ioctl_stub(). Note that 2. is also checked later in add_del_if(), but it's better performed before RTNL. SIOCBRADDIF and SIOCBRDELIF have been processed in dev_ioctl() since the pre-git era, and there seems to be no specific reason to process them there. [0]: unregister_netdevice: waiting for wpan3 to become free. Usage count = 2 ref_tracker: wpan3@ffff8880662d8608 has 1/1 users at __netdev_tracker_alloc include/linux/netdevice.h:4282 [inline] netdev_hold include/linux/netdevice.h:4311 [inline] dev_ifsioc+0xc6a/0x1160 net/core/dev_ioctl.c:624 dev_ioctl+0x255/0x10c0 net/core/dev_ioctl.c:826 sock_do_ioctl+0x1ca/0x260 net/socket.c:1213 sock_ioctl+0x23a/0x6c0 net/socket.c:1318 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl fs/ioctl.c:892 [inline] __x64_sys_ioctl+0x1a4/0x210 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcb/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Fixes: 893b19587534 ("net: bridge: fix ioctl locking") Reported-by: syzkaller <syzkaller@googlegroups.com> Reported-by: yan kang <kangyan91@outlook.com> Reported-by: yue sun <samsun1006219@gmail.com> Closes: https://lore.kernel.org/netdev/SY8P300MB0421225D54EB92762AE8F0F2A1D32@SY8P300MB0421.AUSP300.PROD.OUTLOOK.COM/ Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Stanislav Fomichev <sdf@fomichev.me> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250316192851.19781-1-kuniyu@amazon.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-03-16 12:28:37 -07:00
bridge: Fix a deadlock when enabling multicast snooping When enabling multicast snooping, bridge module deadlocks on multicast_lock if 1) IPv6 is enabled, and 2) there is an existing querier on the same L2 network. The deadlock was caused by the following sequence: While holding the lock, br_multicast_open calls br_multicast_join_snoopers, which eventually causes IP stack to (attempt to) send out a Listener Report (in igmp6_join_group). Since the destination Ethernet address is a multicast address, br_dev_xmit feeds the packet back to the bridge via br_multicast_rcv, which in turn calls br_multicast_add_group, which then deadlocks on multicast_lock. The fix is to move the call br_multicast_join_snoopers outside of the critical section. This works since br_multicast_join_snoopers only deals with IP and does not modify any multicast data structures of the bridge, so there's no need to hold the lock. Steps to reproduce: 1. sysctl net.ipv6.conf.all.force_mld_version=1 2. have another querier 3. ip link set dev bridge type bridge mcast_snooping 0 && \ ip link set dev bridge type bridge mcast_snooping 1 < deadlock > A typical call trace looks like the following: [ 936.251495] _raw_spin_lock+0x5c/0x68 [ 936.255221] br_multicast_add_group+0x40/0x170 [bridge] [ 936.260491] br_multicast_rcv+0x7ac/0xe30 [bridge] [ 936.265322] br_dev_xmit+0x140/0x368 [bridge] [ 936.269689] dev_hard_start_xmit+0x94/0x158 [ 936.273876] __dev_queue_xmit+0x5ac/0x7f8 [ 936.277890] dev_queue_xmit+0x10/0x18 [ 936.281563] neigh_resolve_output+0xec/0x198 [ 936.285845] ip6_finish_output2+0x240/0x710 [ 936.290039] __ip6_finish_output+0x130/0x170 [ 936.294318] ip6_output+0x6c/0x1c8 [ 936.297731] NF_HOOK.constprop.0+0xd8/0xe8 [ 936.301834] igmp6_send+0x358/0x558 [ 936.305326] igmp6_join_group.part.0+0x30/0xf0 [ 936.309774] igmp6_group_added+0xfc/0x110 [ 936.313787] __ipv6_dev_mc_inc+0x1a4/0x290 [ 936.317885] ipv6_dev_mc_inc+0x10/0x18 [ 936.321677] br_multicast_open+0xbc/0x110 [bridge] [ 936.326506] br_multicast_toggle+0xec/0x140 [bridge] Fixes: 4effd28c1245 ("bridge: join all-snoopers multicast address") Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Link: https://lore.kernel.org/r/20201204235628.50653-1-Joseph.Huang@garmin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-04 18:56:28 -05:00
net: bridge: Add netlink knobs for number / maximum MDB entries The previous patch added accounting for number of MDB entries per port and per port-VLAN, and the logic to verify that these values stay within configured bounds. However it didn't provide means to actually configure those bounds or read the occupancy. This patch does that. Two new netlink attributes are added for the MDB occupancy: IFLA_BRPORT_MCAST_N_GROUPS for the per-port occupancy and BRIDGE_VLANDB_ENTRY_MCAST_N_GROUPS for the per-port-VLAN occupancy. And another two for the maximum number of MDB entries: IFLA_BRPORT_MCAST_MAX_GROUPS for the per-port maximum, and BRIDGE_VLANDB_ENTRY_MCAST_MAX_GROUPS for the per-port-VLAN one. Note that the two new IFLA_BRPORT_ attributes prompt bumping of RTNL_SLAVE_MAX_TYPE to size the slave attribute tables large enough. The new attributes are used like this: # ip link add name br up type bridge vlan_filtering 1 mcast_snooping 1 \ mcast_vlan_snooping 1 mcast_querier 1 # ip link set dev v1 master br # bridge vlan add dev v1 vid 2 # bridge vlan set dev v1 vid 1 mcast_max_groups 1 # bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 1 # bridge mdb add dev br port v1 grp 230.1.2.4 temp vid 1 Error: bridge: Port-VLAN is already in 1 groups, and mcast_max_groups=1. # bridge link set dev v1 mcast_max_groups 1 # bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 2 Error: bridge: Port is already in 1 groups, and mcast_max_groups=1. # bridge -d link show 5: v1@v2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br [...] [...] mcast_n_groups 1 mcast_max_groups 1 # bridge -d vlan show port vlan-id br 1 PVID Egress Untagged state forwarding mcast_router 1 v1 1 PVID Egress Untagged [...] mcast_n_groups 1 mcast_max_groups 1 2 [...] mcast_n_groups 0 mcast_max_groups 0 Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-02 18:59:26 +01:00
net: bridge: mcast: update multicast contex when vlan state is changed When the vlan STP state is changed, which could be manipulated by "bridge vlan" commands, similar to port STP state, this also impacts multicast behaviors such as igmp query. In the scenario of per-VLAN snooping, there's a need to update the corresponding multicast context to re-arm the port query timer when vlan state becomes "forwarding" etc. Update br_vlan_set_state() function to enable vlan multicast context in such scenario. Before the patch, the IGMP query does not happen in the last step of the following test sequence, i.e. no growth for tx counter: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 After the patch, the IGMP query happens in the last step of the test: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 3 Signed-off-by: Yong Wang <yongwang@nvidia.com> Reviewed-by: Andy Roulin <aroulin@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-04-17 15:43:13 +02:00
net: bridge: move the switchdev object replay helpers to "push" mode Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"), DSA has introduced some bridge helpers that replay switchdev events (FDB/MDB/VLAN additions and deletions) that can be lost by the switchdev drivers in a variety of circumstances: - an IP multicast group was host-joined on the bridge itself before any switchdev port joined the bridge, leading to the host MDB entries missing in the hardware database. - during the bridge creation process, the MAC address of the bridge was added to the FDB as an entry pointing towards the bridge device itself, but with no switchdev ports being part of the bridge yet, this local FDB entry would remain unknown to the switchdev hardware database. - a VLAN/FDB/MDB was added to a bridge port that is a LAG interface, before any switchdev port joined that LAG, leading to the hardware database missing those entries. - a switchdev port left a LAG that is a bridge port, while the LAG remained part of the bridge, and all FDB/MDB/VLAN entries remained installed in the hardware database of the switchdev port. Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events for LAG ports which didn't request replay"), DSA introduced a method, based on a const void *ctx, to ensure that two switchdev ports under the same LAG that is a bridge port do not see the same MDB/VLAN entry being replayed twice by the bridge, once for every bridge port that joins the LAG. With so many ordering corner cases being possible, it seems unreasonable to expect a switchdev driver writer to get it right from the first try. Therefore, now that DSA has experimented with the bridge replay helpers for a little bit, we can move the code to the bridge driver where it is more readily available to all switchdev drivers. To convert the switchdev object replay helpers from "pull mode" (where the driver asks for them) to a "push mode" (where the bridge offers them automatically), the biggest problem is that the bridge needs to be aware when a switchdev port joins and leaves, even when the switchdev is only indirectly a bridge port (for example when the bridge port is a LAG upper of the switchdev). Luckily, we already have a hook for that, in the form of the newly introduced switchdev_bridge_port_offload() and switchdev_bridge_port_unoffload() calls. These offer a natural place for hooking the object addition and deletion replays. Extend the above 2 functions with: - pointers to the switchdev atomic notifier (for FDB replays) and the blocking notifier (for MDB and VLAN replays). - the "const void *ctx" argument required for drivers to be able to disambiguate between which port is targeted, when multiple ports are lowers of the same LAG that is a bridge port. Most of the drivers pass NULL to this argument, except the ones that support LAG offload and have the proper context check already in place in the switchdev blocking notifier handler. Also unexport the replay helpers, since nobody except the bridge calls them directly now. Note that: (a) we abuse the terminology slightly, because FDB entries are not "switchdev objects", but we count them as objects nonetheless. With no direct way to prove it, I think they are not modeled as switchdev objects because those can only be installed by the bridge to the hardware (as opposed to FDB entries which can be propagated in the other direction too). This is merely an abuse of terms, FDB entries are replayed too, despite not being objects. (b) the bridge does not attempt to sync port attributes to newly joined ports, just the countable stuff (the objects). The reason for this is simple: no universal and symmetric way to sync and unsync them is known. For example, VLAN filtering: what to do on unsync, disable or leave it enabled? Similarly, STP state, ageing timer, etc etc. What a switchdev port does when it becomes standalone again is not really up to the bridge's competence, and the driver should deal with it. On the other hand, replaying deletions of switchdev objects can be seen a matter of cleanup and therefore be treated by the bridge, hence this patch. We make the replay helpers opt-in for drivers, because they might not bring immediate benefits for them: - nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(), so br_vlan_replay() should not do anything for the new drivers on which we call it. The existing drivers where there was even a slight possibility for there to exist a VLAN on a bridge port before they join it are already guarded against this: mlxsw and prestera deny joining LAG interfaces that are members of a bridge. - br_fdb_replay() should now notify of local FDB entries, but I patched all drivers except DSA to ignore these new entries in commit 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications"). Driver authors can lift this restriction as they wish, and when they do, they can also opt into the FDB replay functionality. - br_mdb_replay() should fix a real issue which is described in commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"). However most drivers do not offload the SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw offload this switchdev object, and I don't completely understand the way in which they offload this switchdev object anyway. So I'll leave it up to these drivers' respective maintainers to opt into br_mdb_replay(). So most of the drivers pass NULL notifier blocks for the replay helpers, except: - dpaa2-switch which was already acked/regression-tested with the helpers enabled (and there isn't much of a downside in having them) - ocelot which already had replay logic in "pull" mode - DSA which already had replay logic in "pull" mode An important observation is that the drivers which don't currently request bridge event replays don't even have the switchdev_bridge_port_{offload,unoffload} calls placed in proper places right now. This was done to avoid unnecessary rework for drivers which might never even add support for this. For driver writers who wish to add replay support, this can be used as a tentative placement guide: https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/ Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:24:03 +03:00
bridge: mcast: fix disabled snooping after long uptime The original idea of the delay_time check was to not apply multicast snooping too early when an MLD querier appears. And to instead wait at least for MLD reports to arrive before switching from flooding to group based, MLD snooped forwarding, to avoid temporary packet loss. However in a batman-adv mesh network it was noticed that after 248 days of uptime 32bit MIPS based devices would start to signal that they had stopped applying multicast snooping due to missing queriers - even though they were the elected querier and still sending MLD queries themselves. While time_is_before_jiffies() generally is safe against jiffies wrap-arounds, like the code comments in jiffies.h explain, it won't be able to track a difference larger than ULONG_MAX/2. With a 32bit large jiffies and one jiffies tick every 10ms (CONFIG_HZ=100) on these MIPS devices running OpenWrt this would result in a difference larger than ULONG_MAX/2 after 248 (= 2^32/100/60/60/24/2) days and time_is_before_jiffies() would then start to return false instead of true. Leading to multicast snooping not being applied to multicast packets anymore. Fix this issue by using a proper timer_list object which won't have this ULONG_MAX/2 difference limitation. Fixes: b00589af3b04 ("bridge: disable snooping if there is no querier") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20240127175033.9640-1-linus.luessing@c0d3.blue Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-01-27 18:50:32 +01:00
bridge: Check relevant per-VLAN options in VLAN range grouping The br_vlan_opts_eq_range() function determines if consecutive VLANs can be grouped together in a range for compact netlink notifications. It currently checks state, tunnel info, and multicast router configuration, but misses two categories of per-VLAN options that affect the output: 1. User-visible priv_flags (neigh_suppress, mcast_enabled) 2. Port multicast context (mcast_max_groups, mcast_n_groups) When VLANs have different settings for these options, they are incorrectly grouped into ranges, causing netlink notifications to report only one VLAN's settings for the entire range. Fix by checking priv_flags equality, but only for flags that affect netlink output (BR_VLFLAG_NEIGH_SUPPRESS_ENABLED and BR_VLFLAG_MCAST_ENABLED), and comparing multicast context (mcast_max_groups and mcast_n_groups). Example showing the bugs before the fix: $ bridge vlan set vid 10 dev dummy1 neigh_suppress on $ bridge vlan set vid 11 dev dummy1 neigh_suppress off $ bridge -d vlan show dev dummy1 port vlan-id dummy1 10-11 ... neigh_suppress on $ bridge vlan set vid 10 dev dummy1 mcast_max_groups 100 $ bridge vlan set vid 11 dev dummy1 mcast_max_groups 200 $ bridge -d vlan show dev dummy1 port vlan-id dummy1 10-11 ... mcast_max_groups 100 After the fix, VLANs 10 and 11 are shown as separate entries with their correct individual settings. Fixes: a1aee20d5db2 ("net: bridge: Add netlink knobs for number / maximum MDB entries") Fixes: 83f6d600796c ("bridge: vlan: Allow setting VLAN neighbor suppression state") Signed-off-by: Danielle Ratson <danieller@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20260225143956.3995415-2-danieller@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2026-02-25 16:39:55 +02:00
bridge: Fix a deadlock when enabling multicast snooping When enabling multicast snooping, bridge module deadlocks on multicast_lock if 1) IPv6 is enabled, and 2) there is an existing querier on the same L2 network. The deadlock was caused by the following sequence: While holding the lock, br_multicast_open calls br_multicast_join_snoopers, which eventually causes IP stack to (attempt to) send out a Listener Report (in igmp6_join_group). Since the destination Ethernet address is a multicast address, br_dev_xmit feeds the packet back to the bridge via br_multicast_rcv, which in turn calls br_multicast_add_group, which then deadlocks on multicast_lock. The fix is to move the call br_multicast_join_snoopers outside of the critical section. This works since br_multicast_join_snoopers only deals with IP and does not modify any multicast data structures of the bridge, so there's no need to hold the lock. Steps to reproduce: 1. sysctl net.ipv6.conf.all.force_mld_version=1 2. have another querier 3. ip link set dev bridge type bridge mcast_snooping 0 && \ ip link set dev bridge type bridge mcast_snooping 1 < deadlock > A typical call trace looks like the following: [ 936.251495] _raw_spin_lock+0x5c/0x68 [ 936.255221] br_multicast_add_group+0x40/0x170 [bridge] [ 936.260491] br_multicast_rcv+0x7ac/0xe30 [bridge] [ 936.265322] br_dev_xmit+0x140/0x368 [bridge] [ 936.269689] dev_hard_start_xmit+0x94/0x158 [ 936.273876] __dev_queue_xmit+0x5ac/0x7f8 [ 936.277890] dev_queue_xmit+0x10/0x18 [ 936.281563] neigh_resolve_output+0xec/0x198 [ 936.285845] ip6_finish_output2+0x240/0x710 [ 936.290039] __ip6_finish_output+0x130/0x170 [ 936.294318] ip6_output+0x6c/0x1c8 [ 936.297731] NF_HOOK.constprop.0+0xd8/0xe8 [ 936.301834] igmp6_send+0x358/0x558 [ 936.305326] igmp6_join_group.part.0+0x30/0xf0 [ 936.309774] igmp6_group_added+0xfc/0x110 [ 936.313787] __ipv6_dev_mc_inc+0x1a4/0x290 [ 936.317885] ipv6_dev_mc_inc+0x10/0x18 [ 936.321677] br_multicast_open+0xbc/0x110 [bridge] [ 936.326506] br_multicast_toggle+0xec/0x140 [bridge] Fixes: 4effd28c1245 ("bridge: join all-snoopers multicast address") Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Link: https://lore.kernel.org/r/20201204235628.50653-1-Joseph.Huang@garmin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-04 18:56:28 -05:00
net: bridge: mcast: update multicast contex when vlan state is changed When the vlan STP state is changed, which could be manipulated by "bridge vlan" commands, similar to port STP state, this also impacts multicast behaviors such as igmp query. In the scenario of per-VLAN snooping, there's a need to update the corresponding multicast context to re-arm the port query timer when vlan state becomes "forwarding" etc. Update br_vlan_set_state() function to enable vlan multicast context in such scenario. Before the patch, the IGMP query does not happen in the last step of the following test sequence, i.e. no growth for tx counter: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 After the patch, the IGMP query happens in the last step of the test: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 3 Signed-off-by: Yong Wang <yongwang@nvidia.com> Reviewed-by: Andy Roulin <aroulin@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-04-17 15:43:13 +02:00
net: bridge: move the switchdev object replay helpers to "push" mode Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"), DSA has introduced some bridge helpers that replay switchdev events (FDB/MDB/VLAN additions and deletions) that can be lost by the switchdev drivers in a variety of circumstances: - an IP multicast group was host-joined on the bridge itself before any switchdev port joined the bridge, leading to the host MDB entries missing in the hardware database. - during the bridge creation process, the MAC address of the bridge was added to the FDB as an entry pointing towards the bridge device itself, but with no switchdev ports being part of the bridge yet, this local FDB entry would remain unknown to the switchdev hardware database. - a VLAN/FDB/MDB was added to a bridge port that is a LAG interface, before any switchdev port joined that LAG, leading to the hardware database missing those entries. - a switchdev port left a LAG that is a bridge port, while the LAG remained part of the bridge, and all FDB/MDB/VLAN entries remained installed in the hardware database of the switchdev port. Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events for LAG ports which didn't request replay"), DSA introduced a method, based on a const void *ctx, to ensure that two switchdev ports under the same LAG that is a bridge port do not see the same MDB/VLAN entry being replayed twice by the bridge, once for every bridge port that joins the LAG. With so many ordering corner cases being possible, it seems unreasonable to expect a switchdev driver writer to get it right from the first try. Therefore, now that DSA has experimented with the bridge replay helpers for a little bit, we can move the code to the bridge driver where it is more readily available to all switchdev drivers. To convert the switchdev object replay helpers from "pull mode" (where the driver asks for them) to a "push mode" (where the bridge offers them automatically), the biggest problem is that the bridge needs to be aware when a switchdev port joins and leaves, even when the switchdev is only indirectly a bridge port (for example when the bridge port is a LAG upper of the switchdev). Luckily, we already have a hook for that, in the form of the newly introduced switchdev_bridge_port_offload() and switchdev_bridge_port_unoffload() calls. These offer a natural place for hooking the object addition and deletion replays. Extend the above 2 functions with: - pointers to the switchdev atomic notifier (for FDB replays) and the blocking notifier (for MDB and VLAN replays). - the "const void *ctx" argument required for drivers to be able to disambiguate between which port is targeted, when multiple ports are lowers of the same LAG that is a bridge port. Most of the drivers pass NULL to this argument, except the ones that support LAG offload and have the proper context check already in place in the switchdev blocking notifier handler. Also unexport the replay helpers, since nobody except the bridge calls them directly now. Note that: (a) we abuse the terminology slightly, because FDB entries are not "switchdev objects", but we count them as objects nonetheless. With no direct way to prove it, I think they are not modeled as switchdev objects because those can only be installed by the bridge to the hardware (as opposed to FDB entries which can be propagated in the other direction too). This is merely an abuse of terms, FDB entries are replayed too, despite not being objects. (b) the bridge does not attempt to sync port attributes to newly joined ports, just the countable stuff (the objects). The reason for this is simple: no universal and symmetric way to sync and unsync them is known. For example, VLAN filtering: what to do on unsync, disable or leave it enabled? Similarly, STP state, ageing timer, etc etc. What a switchdev port does when it becomes standalone again is not really up to the bridge's competence, and the driver should deal with it. On the other hand, replaying deletions of switchdev objects can be seen a matter of cleanup and therefore be treated by the bridge, hence this patch. We make the replay helpers opt-in for drivers, because they might not bring immediate benefits for them: - nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(), so br_vlan_replay() should not do anything for the new drivers on which we call it. The existing drivers where there was even a slight possibility for there to exist a VLAN on a bridge port before they join it are already guarded against this: mlxsw and prestera deny joining LAG interfaces that are members of a bridge. - br_fdb_replay() should now notify of local FDB entries, but I patched all drivers except DSA to ignore these new entries in commit 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications"). Driver authors can lift this restriction as they wish, and when they do, they can also opt into the FDB replay functionality. - br_mdb_replay() should fix a real issue which is described in commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"). However most drivers do not offload the SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw offload this switchdev object, and I don't completely understand the way in which they offload this switchdev object anyway. So I'll leave it up to these drivers' respective maintainers to opt into br_mdb_replay(). So most of the drivers pass NULL notifier blocks for the replay helpers, except: - dpaa2-switch which was already acked/regression-tested with the helpers enabled (and there isn't much of a downside in having them) - ocelot which already had replay logic in "pull" mode - DSA which already had replay logic in "pull" mode An important observation is that the drivers which don't currently request bridge event replays don't even have the switchdev_bridge_port_{offload,unoffload} calls placed in proper places right now. This was done to avoid unnecessary rework for drivers which might never even add support for this. For driver writers who wish to add replay support, this can be used as a tentative placement guide: https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/ Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:24:03 +03:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER Most of the bridge device's vlan init bugs come from the fact that its default pvid is created at the wrong time, way too early in ndo_init() before the device is even assigned an ifindex. It introduces a bug when the bridge's dev_addr is added as fdb during the initial default pvid creation the notification has ifindex/NDA_MASTER both equal to 0 (see example below) which really makes no sense for user-space[0] and is wrong. Usually user-space software would ignore such entries, but they are actually valid and will eventually have all necessary attributes. It makes much more sense to send a notification *after* the device has registered and has a proper ifindex allocated rather than before when there's a chance that the registration might still fail or to receive it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush from br_vlan_flush() since that case can no longer happen. At NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything depending why it was called (if called due to NETDEV_REGISTER error it'll still be == 1, otherwise it could be any value changed during the device life time). For the demonstration below a small change to iproute2 for printing all fdb notifications is added, because it contained a workaround not to show entries with ifindex == 0. Command executed while monitoring: $ ip l add br0 type bridge Before (both ifindex and master == 0): $ bridge monitor fdb 36:7e:8a:b3:56:ba dev * vlan 1 master * permanent After (proper br0 ifindex): $ bridge monitor fdb e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER v3: send the correct v2 patch with all changes (stub should return 0) v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in the br_vlan_bridge_event stub when bridge vlans are disabled [0] https://bugzilla.kernel.org/show_bug.cgi?id=204389 Reported-by: michael-dev <michael-dev@fami-braun.de> Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-02 13:57:36 +03:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: Automatically manage port promiscuous mode. There exist configurations where the administrator or another management entity has the foreknowledge of all the mac addresses of end systems that are being bridged together. In these environments, the administrator can statically configure known addresses in the bridge FDB and disable flooding and learning on ports. This makes it possible to turn off promiscuous mode on the interfaces connected to the bridge. Here is why disabling flooding and learning allows us to control promiscuity: Consider port X. All traffic coming into this port from outside the bridge (ingress) will be either forwarded through other ports of the bridge (egress) or dropped. Forwarding (egress) is defined by FDB entries and by flooding in the event that no FDB entry exists. In the event that flooding is disabled, only FDB entries define the egress. Once learning is disabled, only static FDB entries provided by a management entity define the egress. If we provide information from these static FDBs to the ingress port X, then we'll be able to accept all traffic that can be successfully forwarded and drop all the other traffic sooner without spending CPU cycles to process it. Another way to define the above is as following equations: ingress = egress + drop expanding egress ingress = static FDB + learned FDB + flooding + drop disabling flooding and learning we a left with ingress = static FDB + drop By adding addresses from the static FDB entries to the MAC address filter of an ingress port X, we fully define what the bridge can process without dropping and can thus turn off promiscuous mode, thus dropping packets sooner. There have been suggestions that we may want to allow learning and update the filters with learned addresses as well. This would require mac-level authentication similar to 802.1x to prevent attacks against the hw filters as they are limited resource. Additionally, if the user places the bridge device in promiscuous mode, all ports are placed in promiscuous mode regardless of the changes to flooding and learning. Since the above functionality depends on full static configuration, we have also require that vlan filtering be enabled to take advantage of this. The reason is that the bridge has to be able to receive and process VLAN-tagged frames and the there are only 2 ways to accomplish this right now: promiscuous mode or vlan filtering. Suggested-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 09:59:20 -04:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
bridge: vlan: add per-vlan struct and move to rhashtables This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-25 19:00:11 +02:00
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER Most of the bridge device's vlan init bugs come from the fact that its default pvid is created at the wrong time, way too early in ndo_init() before the device is even assigned an ifindex. It introduces a bug when the bridge's dev_addr is added as fdb during the initial default pvid creation the notification has ifindex/NDA_MASTER both equal to 0 (see example below) which really makes no sense for user-space[0] and is wrong. Usually user-space software would ignore such entries, but they are actually valid and will eventually have all necessary attributes. It makes much more sense to send a notification *after* the device has registered and has a proper ifindex allocated rather than before when there's a chance that the registration might still fail or to receive it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush from br_vlan_flush() since that case can no longer happen. At NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything depending why it was called (if called due to NETDEV_REGISTER error it'll still be == 1, otherwise it could be any value changed during the device life time). For the demonstration below a small change to iproute2 for printing all fdb notifications is added, because it contained a workaround not to show entries with ifindex == 0. Command executed while monitoring: $ ip l add br0 type bridge Before (both ifindex and master == 0): $ bridge monitor fdb 36:7e:8a:b3:56:ba dev * vlan 1 master * permanent After (proper br0 ifindex): $ bridge monitor fdb e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER v3: send the correct v2 patch with all changes (stub should return 0) v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in the br_vlan_bridge_event stub when bridge vlans are disabled [0] https://bugzilla.kernel.org/show_bug.cgi?id=204389 Reported-by: michael-dev <michael-dev@fami-braun.de> Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-02 13:57:36 +03:00
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER Most of the bridge device's vlan init bugs come from the fact that its default pvid is created at the wrong time, way too early in ndo_init() before the device is even assigned an ifindex. It introduces a bug when the bridge's dev_addr is added as fdb during the initial default pvid creation the notification has ifindex/NDA_MASTER both equal to 0 (see example below) which really makes no sense for user-space[0] and is wrong. Usually user-space software would ignore such entries, but they are actually valid and will eventually have all necessary attributes. It makes much more sense to send a notification *after* the device has registered and has a proper ifindex allocated rather than before when there's a chance that the registration might still fail or to receive it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush from br_vlan_flush() since that case can no longer happen. At NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything depending why it was called (if called due to NETDEV_REGISTER error it'll still be == 1, otherwise it could be any value changed during the device life time). For the demonstration below a small change to iproute2 for printing all fdb notifications is added, because it contained a workaround not to show entries with ifindex == 0. Command executed while monitoring: $ ip l add br0 type bridge Before (both ifindex and master == 0): $ bridge monitor fdb 36:7e:8a:b3:56:ba dev * vlan 1 master * permanent After (proper br0 ifindex): $ bridge monitor fdb e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER v3: send the correct v2 patch with all changes (stub should return 0) v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in the br_vlan_bridge_event stub when bridge vlans are disabled [0] https://bugzilla.kernel.org/show_bug.cgi?id=204389 Reported-by: michael-dev <michael-dev@fami-braun.de> Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-02 13:57:36 +03:00
net: bridge: move the switchdev object replay helpers to "push" mode Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"), DSA has introduced some bridge helpers that replay switchdev events (FDB/MDB/VLAN additions and deletions) that can be lost by the switchdev drivers in a variety of circumstances: - an IP multicast group was host-joined on the bridge itself before any switchdev port joined the bridge, leading to the host MDB entries missing in the hardware database. - during the bridge creation process, the MAC address of the bridge was added to the FDB as an entry pointing towards the bridge device itself, but with no switchdev ports being part of the bridge yet, this local FDB entry would remain unknown to the switchdev hardware database. - a VLAN/FDB/MDB was added to a bridge port that is a LAG interface, before any switchdev port joined that LAG, leading to the hardware database missing those entries. - a switchdev port left a LAG that is a bridge port, while the LAG remained part of the bridge, and all FDB/MDB/VLAN entries remained installed in the hardware database of the switchdev port. Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events for LAG ports which didn't request replay"), DSA introduced a method, based on a const void *ctx, to ensure that two switchdev ports under the same LAG that is a bridge port do not see the same MDB/VLAN entry being replayed twice by the bridge, once for every bridge port that joins the LAG. With so many ordering corner cases being possible, it seems unreasonable to expect a switchdev driver writer to get it right from the first try. Therefore, now that DSA has experimented with the bridge replay helpers for a little bit, we can move the code to the bridge driver where it is more readily available to all switchdev drivers. To convert the switchdev object replay helpers from "pull mode" (where the driver asks for them) to a "push mode" (where the bridge offers them automatically), the biggest problem is that the bridge needs to be aware when a switchdev port joins and leaves, even when the switchdev is only indirectly a bridge port (for example when the bridge port is a LAG upper of the switchdev). Luckily, we already have a hook for that, in the form of the newly introduced switchdev_bridge_port_offload() and switchdev_bridge_port_unoffload() calls. These offer a natural place for hooking the object addition and deletion replays. Extend the above 2 functions with: - pointers to the switchdev atomic notifier (for FDB replays) and the blocking notifier (for MDB and VLAN replays). - the "const void *ctx" argument required for drivers to be able to disambiguate between which port is targeted, when multiple ports are lowers of the same LAG that is a bridge port. Most of the drivers pass NULL to this argument, except the ones that support LAG offload and have the proper context check already in place in the switchdev blocking notifier handler. Also unexport the replay helpers, since nobody except the bridge calls them directly now. Note that: (a) we abuse the terminology slightly, because FDB entries are not "switchdev objects", but we count them as objects nonetheless. With no direct way to prove it, I think they are not modeled as switchdev objects because those can only be installed by the bridge to the hardware (as opposed to FDB entries which can be propagated in the other direction too). This is merely an abuse of terms, FDB entries are replayed too, despite not being objects. (b) the bridge does not attempt to sync port attributes to newly joined ports, just the countable stuff (the objects). The reason for this is simple: no universal and symmetric way to sync and unsync them is known. For example, VLAN filtering: what to do on unsync, disable or leave it enabled? Similarly, STP state, ageing timer, etc etc. What a switchdev port does when it becomes standalone again is not really up to the bridge's competence, and the driver should deal with it. On the other hand, replaying deletions of switchdev objects can be seen a matter of cleanup and therefore be treated by the bridge, hence this patch. We make the replay helpers opt-in for drivers, because they might not bring immediate benefits for them: - nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(), so br_vlan_replay() should not do anything for the new drivers on which we call it. The existing drivers where there was even a slight possibility for there to exist a VLAN on a bridge port before they join it are already guarded against this: mlxsw and prestera deny joining LAG interfaces that are members of a bridge. - br_fdb_replay() should now notify of local FDB entries, but I patched all drivers except DSA to ignore these new entries in commit 2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB notifications"). Driver authors can lift this restriction as they wish, and when they do, they can also opt into the FDB replay functionality. - br_mdb_replay() should fix a real issue which is described in commit 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries"). However most drivers do not offload the SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw offload this switchdev object, and I don't completely understand the way in which they offload this switchdev object anyway. So I'll leave it up to these drivers' respective maintainers to opt into br_mdb_replay(). So most of the drivers pass NULL notifier blocks for the replay helpers, except: - dpaa2-switch which was already acked/regression-tested with the helpers enabled (and there isn't much of a downside in having them) - ocelot which already had replay logic in "pull" mode - DSA which already had replay logic in "pull" mode An important observation is that the drivers which don't currently request bridge event replays don't even have the switchdev_bridge_port_{offload,unoffload} calls placed in proper places right now. This was done to avoid unnecessary rework for drivers which might never even add support for this. For driver writers who wish to add replay support, this can be used as a tentative placement guide: https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/ Cc: Vadym Kochan <vkochan@marvell.com> Cc: Taras Chornyi <tchornyi@marvell.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-21 19:24:03 +03:00
net: bridge: Add netlink knobs for number / maximum MDB entries The previous patch added accounting for number of MDB entries per port and per port-VLAN, and the logic to verify that these values stay within configured bounds. However it didn't provide means to actually configure those bounds or read the occupancy. This patch does that. Two new netlink attributes are added for the MDB occupancy: IFLA_BRPORT_MCAST_N_GROUPS for the per-port occupancy and BRIDGE_VLANDB_ENTRY_MCAST_N_GROUPS for the per-port-VLAN occupancy. And another two for the maximum number of MDB entries: IFLA_BRPORT_MCAST_MAX_GROUPS for the per-port maximum, and BRIDGE_VLANDB_ENTRY_MCAST_MAX_GROUPS for the per-port-VLAN one. Note that the two new IFLA_BRPORT_ attributes prompt bumping of RTNL_SLAVE_MAX_TYPE to size the slave attribute tables large enough. The new attributes are used like this: # ip link add name br up type bridge vlan_filtering 1 mcast_snooping 1 \ mcast_vlan_snooping 1 mcast_querier 1 # ip link set dev v1 master br # bridge vlan add dev v1 vid 2 # bridge vlan set dev v1 vid 1 mcast_max_groups 1 # bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 1 # bridge mdb add dev br port v1 grp 230.1.2.4 temp vid 1 Error: bridge: Port-VLAN is already in 1 groups, and mcast_max_groups=1. # bridge link set dev v1 mcast_max_groups 1 # bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 2 Error: bridge: Port is already in 1 groups, and mcast_max_groups=1. # bridge -d link show 5: v1@v2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br [...] [...] mcast_n_groups 1 mcast_max_groups 1 # bridge -d vlan show port vlan-id br 1 PVID Egress Untagged state forwarding mcast_router 1 v1 1 PVID Egress Untagged [...] mcast_n_groups 1 mcast_max_groups 1 2 [...] mcast_n_groups 0 mcast_max_groups 0 Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-02 18:59:26 +01:00
net: bridge: mcast: update multicast contex when vlan state is changed When the vlan STP state is changed, which could be manipulated by "bridge vlan" commands, similar to port STP state, this also impacts multicast behaviors such as igmp query. In the scenario of per-VLAN snooping, there's a need to update the corresponding multicast context to re-arm the port query timer when vlan state becomes "forwarding" etc. Update br_vlan_set_state() function to enable vlan multicast context in such scenario. Before the patch, the IGMP query does not happen in the last step of the following test sequence, i.e. no growth for tx counter: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 After the patch, the IGMP query happens in the last step of the test: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 3 Signed-off-by: Yong Wang <yongwang@nvidia.com> Reviewed-by: Andy Roulin <aroulin@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-04-17 15:43:13 +02:00
net: bridge: mcast: update multicast contex when vlan state is changed When the vlan STP state is changed, which could be manipulated by "bridge vlan" commands, similar to port STP state, this also impacts multicast behaviors such as igmp query. In the scenario of per-VLAN snooping, there's a need to update the corresponding multicast context to re-arm the port query timer when vlan state becomes "forwarding" etc. Update br_vlan_set_state() function to enable vlan multicast context in such scenario. Before the patch, the IGMP query does not happen in the last step of the following test sequence, i.e. no growth for tx counter: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 After the patch, the IGMP query happens in the last step of the test: # ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1 mcast_querier 1 mcast_stats_enabled 1 # bridge vlan global set vid 1 dev br1 mcast_snooping 1 mcast_querier 1 mcast_query_interval 100 mcast_startup_query_count 0 # ip link add name swp1 up master br1 type dummy # sleep 1 # bridge vlan set vid 1 dev swp1 state 4 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # sleep 1 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 1 # bridge vlan set vid 1 dev swp1 state 3 # sleep 2 # ip -j -p stats show dev swp1 group xstats_slave subgroup bridge suite mcast | jq '.[]["multicast"]["igmp_queries"]["tx_v2"]' 3 Signed-off-by: Yong Wang <yongwang@nvidia.com> Reviewed-by: Andy Roulin <aroulin@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-04-17 15:43:13 +02:00
bridge: cfm: Netlink SET configuration Interface. This is the implementation of CFM netlink configuration set information interface. Add new nested netlink attributes. These attributes are used by the user space to create/delete/configure CFM instances. SETLINK: IFLA_BRIDGE_CFM: Indicate that the following attributes are CFM. IFLA_BRIDGE_CFM_MEP_CREATE: This indicate that a MEP instance must be created. IFLA_BRIDGE_CFM_MEP_DELETE: This indicate that a MEP instance must be deleted. IFLA_BRIDGE_CFM_MEP_CONFIG: This indicate that a MEP instance must be configured. IFLA_BRIDGE_CFM_CC_CONFIG: This indicate that a MEP instance Continuity Check (CC) functionality must be configured. IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD: This indicate that a CC Peer MEP must be added. IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE: This indicate that a CC Peer MEP must be removed. IFLA_BRIDGE_CFM_CC_CCM_TX: This indicate that the CC transmitted CCM PDU must be configured. IFLA_BRIDGE_CFM_CC_RDI: This indicate that the CC transmitted CCM PDU RDI must be configured. CFM nested attribute has the following attributes in next level. SETLINK RTEXT_FILTER_CFM_CONFIG: IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE: The created MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN: The created MEP domain. The type is u32 (br_cfm_domain). It must be BR_CFM_PORT. This means that CFM frames are transmitted and received directly on the port - untagged. Not in a VLAN. IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION: The created MEP direction. The type is u32 (br_cfm_mep_direction). It must be BR_CFM_MEP_DIRECTION_DOWN. This means that CFM frames are transmitted and received on the port. Not in the bridge. IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX: The created MEP residence port ifindex. The type is u32 (ifindex). IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE: The deleted MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC: The configured MEP unicast MAC address. The type is 6*u8 (array). This is used as SMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL: The configured MEP unicast MD level. The type is u32. It must be in the range 1-7. No CFM frames are passing through this MEP on lower levels. IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID: The configured MEP ID. The type is u32. It must be in the range 0-0x1FFF. This MEP ID is inserted in any transmitted CCM frame. IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE: The Continuity Check (CC) functionality is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL: The CC expected receive interval of CCM frames. The type is u32 (br_cfm_ccm_interval). This is also the transmission interval of CCM frames when enabled. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID: The CC expected receive MAID in CCM frames. The type is CFM_MAID_LENGTH*u8. This is MAID is also inserted in transmitted CCM frames. IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_MEPID: The CC Peer MEP ID added. The type is u32. When a Peer MEP ID is added and CC is enabled it is expected to receive CCM frames from that Peer MEP. IFLA_BRIDGE_CFM_CC_RDI_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_RDI_RDI: The RDI that is inserted in transmitted CCM PDU. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC: The transmitted CCM frame destination MAC address. The type is 6*u8 (array). This is used as DMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE: The transmitted CCM frame update (increment) of sequence number is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD: The period of time where CCM frame are transmitted. The type is u32. The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX must be done before timeout to keep transmission alive. When period is zero any ongoing CCM frame transmission will be stopped. IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV: The transmitted CCM frame update with Interface Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE: The transmitted Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV: The transmitted CCM frame update with Port Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE: The transmitted Port Status TLV value field. The type is u8. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:48 +00:00
bridge: cfm: Kernel space implementation of CFM. MEP create/delete. This is the first commit of the implementation of the CFM protocol according to 802.1Q section 12.14. It contains MEP instance create, delete and configuration. Connectivity Fault Management (CFM) comprises capabilities for detecting, verifying, and isolating connectivity failures in Virtual Bridged Networks. These capabilities can be used in networks operated by multiple independent organizations, each with restricted management access to each others equipment. CFM functions are partitioned as follows: - Path discovery - Fault detection - Fault verification and isolation - Fault notification - Fault recovery Interface consists of these functions: br_cfm_mep_create() br_cfm_mep_delete() br_cfm_mep_config_set() br_cfm_cc_config_set() br_cfm_cc_peer_mep_add() br_cfm_cc_peer_mep_remove() A MEP instance is created by br_cfm_mep_create() -It is the Maintenance association End Point described in 802.1Q section 19.2. -It is created on a specific level (1-7) and is assuring that no CFM frames are passing through this MEP on lower levels. -It initiates and validates CFM frames on its level. -It can only exist on a port that is related to a bridge. -Attributes given cannot be changed until the instance is deleted. A MEP instance can be deleted by br_cfm_mep_delete(). A created MEP instance has attributes that can be configured by br_cfm_mep_config_set(). A MEP Continuity Check feature can be configured by br_cfm_cc_config_set() The Continuity Check Receiver state machine can be enabled and disabled. According to 802.1Q section 19.2.8 A MEP can have Peer MEPs added and removed by br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove() The Continuity Check feature can maintain connectivity status on each added Peer MEP. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:45 +00:00
bridge: cfm: Netlink SET configuration Interface. This is the implementation of CFM netlink configuration set information interface. Add new nested netlink attributes. These attributes are used by the user space to create/delete/configure CFM instances. SETLINK: IFLA_BRIDGE_CFM: Indicate that the following attributes are CFM. IFLA_BRIDGE_CFM_MEP_CREATE: This indicate that a MEP instance must be created. IFLA_BRIDGE_CFM_MEP_DELETE: This indicate that a MEP instance must be deleted. IFLA_BRIDGE_CFM_MEP_CONFIG: This indicate that a MEP instance must be configured. IFLA_BRIDGE_CFM_CC_CONFIG: This indicate that a MEP instance Continuity Check (CC) functionality must be configured. IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD: This indicate that a CC Peer MEP must be added. IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE: This indicate that a CC Peer MEP must be removed. IFLA_BRIDGE_CFM_CC_CCM_TX: This indicate that the CC transmitted CCM PDU must be configured. IFLA_BRIDGE_CFM_CC_RDI: This indicate that the CC transmitted CCM PDU RDI must be configured. CFM nested attribute has the following attributes in next level. SETLINK RTEXT_FILTER_CFM_CONFIG: IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE: The created MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN: The created MEP domain. The type is u32 (br_cfm_domain). It must be BR_CFM_PORT. This means that CFM frames are transmitted and received directly on the port - untagged. Not in a VLAN. IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION: The created MEP direction. The type is u32 (br_cfm_mep_direction). It must be BR_CFM_MEP_DIRECTION_DOWN. This means that CFM frames are transmitted and received on the port. Not in the bridge. IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX: The created MEP residence port ifindex. The type is u32 (ifindex). IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE: The deleted MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC: The configured MEP unicast MAC address. The type is 6*u8 (array). This is used as SMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL: The configured MEP unicast MD level. The type is u32. It must be in the range 1-7. No CFM frames are passing through this MEP on lower levels. IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID: The configured MEP ID. The type is u32. It must be in the range 0-0x1FFF. This MEP ID is inserted in any transmitted CCM frame. IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE: The Continuity Check (CC) functionality is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL: The CC expected receive interval of CCM frames. The type is u32 (br_cfm_ccm_interval). This is also the transmission interval of CCM frames when enabled. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID: The CC expected receive MAID in CCM frames. The type is CFM_MAID_LENGTH*u8. This is MAID is also inserted in transmitted CCM frames. IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_MEPID: The CC Peer MEP ID added. The type is u32. When a Peer MEP ID is added and CC is enabled it is expected to receive CCM frames from that Peer MEP. IFLA_BRIDGE_CFM_CC_RDI_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_RDI_RDI: The RDI that is inserted in transmitted CCM PDU. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC: The transmitted CCM frame destination MAC address. The type is 6*u8 (array). This is used as DMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE: The transmitted CCM frame update (increment) of sequence number is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD: The period of time where CCM frame are transmitted. The type is u32. The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX must be done before timeout to keep transmission alive. When period is zero any ongoing CCM frame transmission will be stopped. IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV: The transmitted CCM frame update with Interface Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE: The transmitted Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV: The transmitted CCM frame update with Port Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE: The transmitted Port Status TLV value field. The type is u8. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:48 +00:00
bridge: cfm: Kernel space implementation of CFM. MEP create/delete. This is the first commit of the implementation of the CFM protocol according to 802.1Q section 12.14. It contains MEP instance create, delete and configuration. Connectivity Fault Management (CFM) comprises capabilities for detecting, verifying, and isolating connectivity failures in Virtual Bridged Networks. These capabilities can be used in networks operated by multiple independent organizations, each with restricted management access to each others equipment. CFM functions are partitioned as follows: - Path discovery - Fault detection - Fault verification and isolation - Fault notification - Fault recovery Interface consists of these functions: br_cfm_mep_create() br_cfm_mep_delete() br_cfm_mep_config_set() br_cfm_cc_config_set() br_cfm_cc_peer_mep_add() br_cfm_cc_peer_mep_remove() A MEP instance is created by br_cfm_mep_create() -It is the Maintenance association End Point described in 802.1Q section 19.2. -It is created on a specific level (1-7) and is assuring that no CFM frames are passing through this MEP on lower levels. -It initiates and validates CFM frames on its level. -It can only exist on a port that is related to a bridge. -Attributes given cannot be changed until the instance is deleted. A MEP instance can be deleted by br_cfm_mep_delete(). A created MEP instance has attributes that can be configured by br_cfm_mep_config_set(). A MEP Continuity Check feature can be configured by br_cfm_cc_config_set() The Continuity Check Receiver state machine can be enabled and disabled. According to 802.1Q section 19.2.8 A MEP can have Peer MEPs added and removed by br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove() The Continuity Check feature can maintain connectivity status on each added Peer MEP. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:45 +00:00
bridge: cfm: Netlink GET configuration Interface. This is the implementation of CFM netlink configuration get information interface. Add new nested netlink attributes. These attributes are used by the user space to get configuration information. GETLINK: Request filter RTEXT_FILTER_CFM_CONFIG: Indicating that CFM configuration information must be delivered. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_CREATE_INFO: This indicate that MEP instance create parameters are following. IFLA_BRIDGE_CFM_MEP_CONFIG_INFO: This indicate that MEP instance config parameters are following. IFLA_BRIDGE_CFM_CC_CONFIG_INFO: This indicate that MEP instance CC functionality parameters are following. IFLA_BRIDGE_CFM_CC_RDI_INFO: This indicate that CC transmitted CCM PDU RDI parameters are following. IFLA_BRIDGE_CFM_CC_CCM_TX_INFO: This indicate that CC transmitted CCM PDU parameters are following. IFLA_BRIDGE_CFM_CC_PEER_MEP_INFO: This indicate that the added peer MEP IDs are following. CFM nested attribute has the following attributes in next level. GETLINK RTEXT_FILTER_CFM_CONFIG: IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE: The created MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN: The created MEP domain. The type is u32 (br_cfm_domain). It must be BR_CFM_PORT. This means that CFM frames are transmitted and received directly on the port - untagged. Not in a VLAN. IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION: The created MEP direction. The type is u32 (br_cfm_mep_direction). It must be BR_CFM_MEP_DIRECTION_DOWN. This means that CFM frames are transmitted and received on the port. Not in the bridge. IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX: The created MEP residence port ifindex. The type is u32 (ifindex). IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE: The deleted MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC: The configured MEP unicast MAC address. The type is 6*u8 (array). This is used as SMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL: The configured MEP unicast MD level. The type is u32. It must be in the range 1-7. No CFM frames are passing through this MEP on lower levels. IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID: The configured MEP ID. The type is u32. It must be in the range 0-0x1FFF. This MEP ID is inserted in any transmitted CCM frame. IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE: The Continuity Check (CC) functionality is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL: The CC expected receive interval of CCM frames. The type is u32 (br_cfm_ccm_interval). This is also the transmission interval of CCM frames when enabled. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID: The CC expected receive MAID in CCM frames. The type is CFM_MAID_LENGTH*u8. This is MAID is also inserted in transmitted CCM frames. IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_MEPID: The CC Peer MEP ID added. The type is u32. When a Peer MEP ID is added and CC is enabled it is expected to receive CCM frames from that Peer MEP. IFLA_BRIDGE_CFM_CC_RDI_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_RDI_RDI: The RDI that is inserted in transmitted CCM PDU. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC: The transmitted CCM frame destination MAC address. The type is 6*u8 (array). This is used as DMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE: The transmitted CCM frame update (increment) of sequence number is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD: The period of time where CCM frame are transmitted. The type is u32. The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX must be done before timeout to keep transmission alive. When period is zero any ongoing CCM frame transmission will be stopped. IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV: The transmitted CCM frame update with Interface Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE: The transmitted Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV: The transmitted CCM frame update with Port Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE: The transmitted Port Status TLV value field. The type is u8. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:49 +00:00
bridge: cfm: Netlink Notifications. This is the implementation of Netlink notifications out of CFM. Notifications are initiated whenever a state change happens in CFM. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is NLA_U32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is NLA_U32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:51 +00:00
bridge: cfm: Kernel space implementation of CFM. MEP create/delete. This is the first commit of the implementation of the CFM protocol according to 802.1Q section 12.14. It contains MEP instance create, delete and configuration. Connectivity Fault Management (CFM) comprises capabilities for detecting, verifying, and isolating connectivity failures in Virtual Bridged Networks. These capabilities can be used in networks operated by multiple independent organizations, each with restricted management access to each others equipment. CFM functions are partitioned as follows: - Path discovery - Fault detection - Fault verification and isolation - Fault notification - Fault recovery Interface consists of these functions: br_cfm_mep_create() br_cfm_mep_delete() br_cfm_mep_config_set() br_cfm_cc_config_set() br_cfm_cc_peer_mep_add() br_cfm_cc_peer_mep_remove() A MEP instance is created by br_cfm_mep_create() -It is the Maintenance association End Point described in 802.1Q section 19.2. -It is created on a specific level (1-7) and is assuring that no CFM frames are passing through this MEP on lower levels. -It initiates and validates CFM frames on its level. -It can only exist on a port that is related to a bridge. -Attributes given cannot be changed until the instance is deleted. A MEP instance can be deleted by br_cfm_mep_delete(). A created MEP instance has attributes that can be configured by br_cfm_mep_config_set(). A MEP Continuity Check feature can be configured by br_cfm_cc_config_set() The Continuity Check Receiver state machine can be enabled and disabled. According to 802.1Q section 19.2.8 A MEP can have Peer MEPs added and removed by br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove() The Continuity Check feature can maintain connectivity status on each added Peer MEP. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:45 +00:00
bridge: cfm: Netlink SET configuration Interface. This is the implementation of CFM netlink configuration set information interface. Add new nested netlink attributes. These attributes are used by the user space to create/delete/configure CFM instances. SETLINK: IFLA_BRIDGE_CFM: Indicate that the following attributes are CFM. IFLA_BRIDGE_CFM_MEP_CREATE: This indicate that a MEP instance must be created. IFLA_BRIDGE_CFM_MEP_DELETE: This indicate that a MEP instance must be deleted. IFLA_BRIDGE_CFM_MEP_CONFIG: This indicate that a MEP instance must be configured. IFLA_BRIDGE_CFM_CC_CONFIG: This indicate that a MEP instance Continuity Check (CC) functionality must be configured. IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD: This indicate that a CC Peer MEP must be added. IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE: This indicate that a CC Peer MEP must be removed. IFLA_BRIDGE_CFM_CC_CCM_TX: This indicate that the CC transmitted CCM PDU must be configured. IFLA_BRIDGE_CFM_CC_RDI: This indicate that the CC transmitted CCM PDU RDI must be configured. CFM nested attribute has the following attributes in next level. SETLINK RTEXT_FILTER_CFM_CONFIG: IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE: The created MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN: The created MEP domain. The type is u32 (br_cfm_domain). It must be BR_CFM_PORT. This means that CFM frames are transmitted and received directly on the port - untagged. Not in a VLAN. IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION: The created MEP direction. The type is u32 (br_cfm_mep_direction). It must be BR_CFM_MEP_DIRECTION_DOWN. This means that CFM frames are transmitted and received on the port. Not in the bridge. IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX: The created MEP residence port ifindex. The type is u32 (ifindex). IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE: The deleted MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC: The configured MEP unicast MAC address. The type is 6*u8 (array). This is used as SMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL: The configured MEP unicast MD level. The type is u32. It must be in the range 1-7. No CFM frames are passing through this MEP on lower levels. IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID: The configured MEP ID. The type is u32. It must be in the range 0-0x1FFF. This MEP ID is inserted in any transmitted CCM frame. IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE: The Continuity Check (CC) functionality is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL: The CC expected receive interval of CCM frames. The type is u32 (br_cfm_ccm_interval). This is also the transmission interval of CCM frames when enabled. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID: The CC expected receive MAID in CCM frames. The type is CFM_MAID_LENGTH*u8. This is MAID is also inserted in transmitted CCM frames. IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_MEPID: The CC Peer MEP ID added. The type is u32. When a Peer MEP ID is added and CC is enabled it is expected to receive CCM frames from that Peer MEP. IFLA_BRIDGE_CFM_CC_RDI_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_RDI_RDI: The RDI that is inserted in transmitted CCM PDU. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC: The transmitted CCM frame destination MAC address. The type is 6*u8 (array). This is used as DMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE: The transmitted CCM frame update (increment) of sequence number is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD: The period of time where CCM frame are transmitted. The type is u32. The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX must be done before timeout to keep transmission alive. When period is zero any ongoing CCM frame transmission will be stopped. IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV: The transmitted CCM frame update with Interface Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE: The transmitted Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV: The transmitted CCM frame update with Port Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE: The transmitted Port Status TLV value field. The type is u8. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:48 +00:00
bridge: cfm: Kernel space implementation of CFM. MEP create/delete. This is the first commit of the implementation of the CFM protocol according to 802.1Q section 12.14. It contains MEP instance create, delete and configuration. Connectivity Fault Management (CFM) comprises capabilities for detecting, verifying, and isolating connectivity failures in Virtual Bridged Networks. These capabilities can be used in networks operated by multiple independent organizations, each with restricted management access to each others equipment. CFM functions are partitioned as follows: - Path discovery - Fault detection - Fault verification and isolation - Fault notification - Fault recovery Interface consists of these functions: br_cfm_mep_create() br_cfm_mep_delete() br_cfm_mep_config_set() br_cfm_cc_config_set() br_cfm_cc_peer_mep_add() br_cfm_cc_peer_mep_remove() A MEP instance is created by br_cfm_mep_create() -It is the Maintenance association End Point described in 802.1Q section 19.2. -It is created on a specific level (1-7) and is assuring that no CFM frames are passing through this MEP on lower levels. -It initiates and validates CFM frames on its level. -It can only exist on a port that is related to a bridge. -Attributes given cannot be changed until the instance is deleted. A MEP instance can be deleted by br_cfm_mep_delete(). A created MEP instance has attributes that can be configured by br_cfm_mep_config_set(). A MEP Continuity Check feature can be configured by br_cfm_cc_config_set() The Continuity Check Receiver state machine can be enabled and disabled. According to 802.1Q section 19.2.8 A MEP can have Peer MEPs added and removed by br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove() The Continuity Check feature can maintain connectivity status on each added Peer MEP. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:45 +00:00
bridge: cfm: Netlink GET configuration Interface. This is the implementation of CFM netlink configuration get information interface. Add new nested netlink attributes. These attributes are used by the user space to get configuration information. GETLINK: Request filter RTEXT_FILTER_CFM_CONFIG: Indicating that CFM configuration information must be delivered. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_CREATE_INFO: This indicate that MEP instance create parameters are following. IFLA_BRIDGE_CFM_MEP_CONFIG_INFO: This indicate that MEP instance config parameters are following. IFLA_BRIDGE_CFM_CC_CONFIG_INFO: This indicate that MEP instance CC functionality parameters are following. IFLA_BRIDGE_CFM_CC_RDI_INFO: This indicate that CC transmitted CCM PDU RDI parameters are following. IFLA_BRIDGE_CFM_CC_CCM_TX_INFO: This indicate that CC transmitted CCM PDU parameters are following. IFLA_BRIDGE_CFM_CC_PEER_MEP_INFO: This indicate that the added peer MEP IDs are following. CFM nested attribute has the following attributes in next level. GETLINK RTEXT_FILTER_CFM_CONFIG: IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE: The created MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN: The created MEP domain. The type is u32 (br_cfm_domain). It must be BR_CFM_PORT. This means that CFM frames are transmitted and received directly on the port - untagged. Not in a VLAN. IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION: The created MEP direction. The type is u32 (br_cfm_mep_direction). It must be BR_CFM_MEP_DIRECTION_DOWN. This means that CFM frames are transmitted and received on the port. Not in the bridge. IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX: The created MEP residence port ifindex. The type is u32 (ifindex). IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE: The deleted MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC: The configured MEP unicast MAC address. The type is 6*u8 (array). This is used as SMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL: The configured MEP unicast MD level. The type is u32. It must be in the range 1-7. No CFM frames are passing through this MEP on lower levels. IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID: The configured MEP ID. The type is u32. It must be in the range 0-0x1FFF. This MEP ID is inserted in any transmitted CCM frame. IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE: The Continuity Check (CC) functionality is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL: The CC expected receive interval of CCM frames. The type is u32 (br_cfm_ccm_interval). This is also the transmission interval of CCM frames when enabled. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID: The CC expected receive MAID in CCM frames. The type is CFM_MAID_LENGTH*u8. This is MAID is also inserted in transmitted CCM frames. IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_MEPID: The CC Peer MEP ID added. The type is u32. When a Peer MEP ID is added and CC is enabled it is expected to receive CCM frames from that Peer MEP. IFLA_BRIDGE_CFM_CC_RDI_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_RDI_RDI: The RDI that is inserted in transmitted CCM PDU. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE: The configured MEP instance number. The type is u32. IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC: The transmitted CCM frame destination MAC address. The type is 6*u8 (array). This is used as DMAC in all transmitted CFM frames. IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE: The transmitted CCM frame update (increment) of sequence number is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD: The period of time where CCM frame are transmitted. The type is u32. The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX must be done before timeout to keep transmission alive. When period is zero any ongoing CCM frame transmission will be stopped. IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV: The transmitted CCM frame update with Interface Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE: The transmitted Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV: The transmitted CCM frame update with Port Status TLV is enabled or disabled. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE: The transmitted Port Status TLV value field. The type is u8. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:49 +00:00
bridge: cfm: Netlink GET status Interface. This is the implementation of CFM netlink status get information interface. Add new nested netlink attributes. These attributes are used by the user space to get status information. GETLINK: Request filter RTEXT_FILTER_CFM_STATUS: Indicating that CFM status information must be delivered. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. GETLINK RTEXT_FILTER_CFM_STATUS: IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is u32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is u32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is u32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is u32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is u32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is u32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is u32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:50 +00:00
bridge: cfm: Netlink Notifications. This is the implementation of Netlink notifications out of CFM. Notifications are initiated whenever a state change happens in CFM. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is NLA_U32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is NLA_U32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:51 +00:00
bridge: cfm: Netlink Notifications. This is the implementation of Netlink notifications out of CFM. Notifications are initiated whenever a state change happens in CFM. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is NLA_U32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is NLA_U32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:51 +00:00
bridge: cfm: Netlink GET status Interface. This is the implementation of CFM netlink status get information interface. Add new nested netlink attributes. These attributes are used by the user space to get status information. GETLINK: Request filter RTEXT_FILTER_CFM_STATUS: Indicating that CFM status information must be delivered. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. GETLINK RTEXT_FILTER_CFM_STATUS: IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is u32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is u32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is u32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is u32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is u32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is u32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is u32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:50 +00:00
bridge: cfm: Netlink GET status Interface. This is the implementation of CFM netlink status get information interface. Add new nested netlink attributes. These attributes are used by the user space to get status information. GETLINK: Request filter RTEXT_FILTER_CFM_STATUS: Indicating that CFM status information must be delivered. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. GETLINK RTEXT_FILTER_CFM_STATUS: IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is u32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is u32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is u32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is u32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is u32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is u32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is u8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is u32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is u32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is u32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:50 +00:00
bridge: cfm: Kernel space implementation of CFM. MEP create/delete. This is the first commit of the implementation of the CFM protocol according to 802.1Q section 12.14. It contains MEP instance create, delete and configuration. Connectivity Fault Management (CFM) comprises capabilities for detecting, verifying, and isolating connectivity failures in Virtual Bridged Networks. These capabilities can be used in networks operated by multiple independent organizations, each with restricted management access to each others equipment. CFM functions are partitioned as follows: - Path discovery - Fault detection - Fault verification and isolation - Fault notification - Fault recovery Interface consists of these functions: br_cfm_mep_create() br_cfm_mep_delete() br_cfm_mep_config_set() br_cfm_cc_config_set() br_cfm_cc_peer_mep_add() br_cfm_cc_peer_mep_remove() A MEP instance is created by br_cfm_mep_create() -It is the Maintenance association End Point described in 802.1Q section 19.2. -It is created on a specific level (1-7) and is assuring that no CFM frames are passing through this MEP on lower levels. -It initiates and validates CFM frames on its level. -It can only exist on a port that is related to a bridge. -Attributes given cannot be changed until the instance is deleted. A MEP instance can be deleted by br_cfm_mep_delete(). A created MEP instance has attributes that can be configured by br_cfm_mep_config_set(). A MEP Continuity Check feature can be configured by br_cfm_cc_config_set() The Continuity Check Receiver state machine can be enabled and disabled. According to 802.1Q section 19.2.8 A MEP can have Peer MEPs added and removed by br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove() The Continuity Check feature can maintain connectivity status on each added Peer MEP. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:45 +00:00
bridge: cfm: Netlink Notifications. This is the implementation of Netlink notifications out of CFM. Notifications are initiated whenever a state change happens in CFM. IFLA_BRIDGE_CFM: Points to the CFM information. IFLA_BRIDGE_CFM_MEP_STATUS_INFO: This indicate that the MEP instance status are following. IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO: This indicate that the peer MEP status are following. CFM nested attribute has the following attributes in next level. IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected Opcode. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN: The MEP instance received CFM PDU with unexpected version. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN: The MEP instance received CCM PDU with MD level lower than configured level. This frame is discarded. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE: The MEP instance number of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID: The added Peer MEP ID of the delivered status. The type is NLA_U32. IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT: The CCM defect status. The type is NLA_U32 (bool). True means no CCM frame is received for 3.25 intervals. IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL. IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI: The last received CCM PDU RDI. The type is NLA_U32 (bool). IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE: The last received CCM PDU Port Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE: The last received CCM PDU Interface Status TLV value field. The type is NLA_U8. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN: A CCM frame has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN: A CCM frame with TLV has been received from Peer MEP. The type is NLA_U32 (bool). This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN: A CCM frame with unexpected sequence number has been received from Peer MEP. The type is NLA_U32 (bool). When a sequence number is not one higher than previously received then it is unexpected. This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO. Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-27 10:02:51 +00:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridge With the introduction of explicit offloading API in switchdev in commit 2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded"), we started having Ethernet switch drivers calling directly into a function exported by net/bridge/br_switchdev.c, which is a function exported by the bridge driver. This means that drivers that did not have an explicit dependency on the bridge before, like cpsw and am65-cpsw, now do - otherwise it is not possible to call a symbol exported by a driver that can be built as module unless you are a module too. There was an attempt to solve the dependency issue in the form of commit b0e81817629a ("net: build all switchdev drivers as modules when the bridge is a module"). Grygorii Strashko, however, says about it: | In my opinion, the problem is a bit bigger here than just fixing the | build :( | | In case, of ^cpsw the switchdev mode is kinda optional and in many | cases (especially for testing purposes, NFS) the multi-mac mode is | still preferable mode. | | There were no such tight dependency between switchdev drivers and | bridge core before and switchdev serviced as independent, notification | based layer between them, so ^cpsw still can be "Y" and bridge can be | "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE | will need to be set as "Y", or we will have to update drivers to | support build with BRIDGE=n and maintain separate builds for | networking vs non-networking testing. But is this enough? Wouldn't | it cause 'chain reaction' required to add more and more "Y" options | (like CONFIG_VLAN_8021Q)? | | PS. Just to be sure we on the same page - ARM builds will be forced | (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our | automation testing will just fail with omap2plus_defconfig. In the light of this, it would be desirable for some configurations to avoid dependencies between switchdev drivers and the bridge, and have the switchdev mode as completely optional within the driver. Arnd Bergmann also tried to write a patch which better expressed the build time dependency for Ethernet switch drivers where the switchdev support is optional, like cpsw/am65-cpsw, and this made the drivers follow the bridge (compile as module if the bridge is a module) only if the optional switchdev support in the driver was enabled in the first place: https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/ but this still did not solve the fact that cpsw and am65-cpsw now must be built as modules when the bridge is a module - it just expressed correctly that optional dependency. But the new behavior is an apparent regression from Grygorii's perspective. So to support the use case where the Ethernet driver is built-in, NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we need a framework that can handle the possible absence of the bridge from the running system, i.e. runtime bloatware as opposed to build-time bloatware. Luckily we already have this framework, since switchdev has been using it extensively. Events from the bridge side are transmitted to the driver side using notifier chains - this was originally done so that unrelated drivers could snoop for events emitted by the bridge towards ports that are implemented by other drivers (think of a switch driver with LAG offload that listens for switchdev events on a bonding/team interface that it offloads). There are also events which are transmitted from the driver side to the bridge side, which again are modeled using notifiers. SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with notifying the bridge that a MAC address has been dynamically learned. So there is a precedent we can use for modeling the new framework. The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work that the bridge needs to do when a port becomes offloaded is blocking in its nature: replay VLANs, MDBs etc. The calling context is indeed blocking (we are under rtnl_mutex), but the existing switchdev notification chain that the bridge is subscribed to is only the atomic one. So we need to subscribe the bridge to the blocking switchdev notification chain too. This patch: - keeps the driver-side perception of the switchdev_bridge_port_{,un}offload unchanged - moves the implementation of switchdev_bridge_port_{,un}offload from the bridge module into the switchdev module. - makes everybody that is subscribed to the switchdev blocking notifier chain "hear" offload & unoffload events - makes the bridge driver subscribe and handle those events - moves the bridge driver's handling of those events into 2 new functions called br_switchdev_port_{,un}offload. These functions contain in fact the core of the logic that was previously in switchdev_bridge_port_{,un}offload, just that now we go through an extra indirection layer to reach them. Unlike all the other switchdev notification structures, the structure used to carry the bridge port information, struct switchdev_notifier_brport_info, does not contain a "bool handled". This is because in the current usage pattern, we always know that a switchdev bridge port offloading event will be handled by the bridge, because the switchdev_bridge_port_offload() call was initiated by a NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event couldn't have happened. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03 23:34:08 +03:00
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22 18:55:38 +03:00
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22 18:55:38 +03:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridge With the introduction of explicit offloading API in switchdev in commit 2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded"), we started having Ethernet switch drivers calling directly into a function exported by net/bridge/br_switchdev.c, which is a function exported by the bridge driver. This means that drivers that did not have an explicit dependency on the bridge before, like cpsw and am65-cpsw, now do - otherwise it is not possible to call a symbol exported by a driver that can be built as module unless you are a module too. There was an attempt to solve the dependency issue in the form of commit b0e81817629a ("net: build all switchdev drivers as modules when the bridge is a module"). Grygorii Strashko, however, says about it: | In my opinion, the problem is a bit bigger here than just fixing the | build :( | | In case, of ^cpsw the switchdev mode is kinda optional and in many | cases (especially for testing purposes, NFS) the multi-mac mode is | still preferable mode. | | There were no such tight dependency between switchdev drivers and | bridge core before and switchdev serviced as independent, notification | based layer between them, so ^cpsw still can be "Y" and bridge can be | "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE | will need to be set as "Y", or we will have to update drivers to | support build with BRIDGE=n and maintain separate builds for | networking vs non-networking testing. But is this enough? Wouldn't | it cause 'chain reaction' required to add more and more "Y" options | (like CONFIG_VLAN_8021Q)? | | PS. Just to be sure we on the same page - ARM builds will be forced | (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our | automation testing will just fail with omap2plus_defconfig. In the light of this, it would be desirable for some configurations to avoid dependencies between switchdev drivers and the bridge, and have the switchdev mode as completely optional within the driver. Arnd Bergmann also tried to write a patch which better expressed the build time dependency for Ethernet switch drivers where the switchdev support is optional, like cpsw/am65-cpsw, and this made the drivers follow the bridge (compile as module if the bridge is a module) only if the optional switchdev support in the driver was enabled in the first place: https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/ but this still did not solve the fact that cpsw and am65-cpsw now must be built as modules when the bridge is a module - it just expressed correctly that optional dependency. But the new behavior is an apparent regression from Grygorii's perspective. So to support the use case where the Ethernet driver is built-in, NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we need a framework that can handle the possible absence of the bridge from the running system, i.e. runtime bloatware as opposed to build-time bloatware. Luckily we already have this framework, since switchdev has been using it extensively. Events from the bridge side are transmitted to the driver side using notifier chains - this was originally done so that unrelated drivers could snoop for events emitted by the bridge towards ports that are implemented by other drivers (think of a switch driver with LAG offload that listens for switchdev events on a bonding/team interface that it offloads). There are also events which are transmitted from the driver side to the bridge side, which again are modeled using notifiers. SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with notifying the bridge that a MAC address has been dynamically learned. So there is a precedent we can use for modeling the new framework. The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work that the bridge needs to do when a port becomes offloaded is blocking in its nature: replay VLANs, MDBs etc. The calling context is indeed blocking (we are under rtnl_mutex), but the existing switchdev notification chain that the bridge is subscribed to is only the atomic one. So we need to subscribe the bridge to the blocking switchdev notification chain too. This patch: - keeps the driver-side perception of the switchdev_bridge_port_{,un}offload unchanged - moves the implementation of switchdev_bridge_port_{,un}offload from the bridge module into the switchdev module. - makes everybody that is subscribed to the switchdev blocking notifier chain "hear" offload & unoffload events - makes the bridge driver subscribe and handle those events - moves the bridge driver's handling of those events into 2 new functions called br_switchdev_port_{,un}offload. These functions contain in fact the core of the logic that was previously in switchdev_bridge_port_{,un}offload, just that now we go through an extra indirection layer to reach them. Unlike all the other switchdev notification structures, the structure used to carry the bridge port information, struct switchdev_notifier_brport_info, does not contain a "bool handled". This is because in the current usage pattern, we always know that a switchdev bridge port offloading event will be handled by the bridge, because the switchdev_bridge_port_offload() call was initiated by a NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event couldn't have happened. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03 23:34:08 +03:00
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22 18:55:38 +03:00
net: bridge: switchdev: allow the TX data plane forwarding to be offloaded Allow switchdevs to forward frames from the CPU in accordance with the bridge configuration in the same way as is done between bridge ports. This means that the bridge will only send a single skb towards one of the ports under the switchdev's control, and expects the driver to deliver the packet to all eligible ports in its domain. Primarily this improves the performance of multicast flows with multiple subscribers, as it allows the hardware to perform the frame replication. The basic flow between the driver and the bridge is as follows: - When joining a bridge port, the switchdev driver calls switchdev_bridge_port_offload() with tx_fwd_offload = true. - The bridge sends offloadable skbs to one of the ports under the switchdev's control using skb->offload_fwd_mark = true. - The switchdev driver checks the skb->offload_fwd_mark field and lets its FDB lookup select the destination port mask for this packet. v1->v2: - convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long - introduce a static key "br_switchdev_fwd_offload_used" to minimize the impact of the newly introduced feature on all the setups which don't have hardware that can make use of it - introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache line access - reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in __br_forward() - do not strip VLAN on egress if forwarding offload on VLAN-aware bridge is being used - propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP v2->v3: - replace the solution based on .ndo_dfwd_add_station with a solution based on switchdev_bridge_port_offload - rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD v3->v4: rebase v4->v5: - make sure the static key is decremented on bridge port unoffload - more function and variable renaming and comments for them: br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload fwd_accel to tx_fwd_offload Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22 18:55:38 +03:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00
bridge: switchdev: Add forward mark support for stacked devices switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-25 18:42:37 +02:00