linux/drivers/pci/controller/vmd.c

1147 lines
30 KiB

x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: Unify ECAM constants in native PCI Express drivers Add ECAM-related constants to provide a set of standard constants defining memory address shift values to the byte-level address that can be used to access the PCI Express Configuration Space, and then move native PCI Express controller drivers to use the newly introduced definitions retiring driver-specific ones. Refactor pci_ecam_map_bus() function to use newly added constants so that limits to the bus, device function and offset (now limited to 4K as per the specification) are in place to prevent the defective or malicious caller from supplying incorrect configuration offset and thus targeting the wrong device when accessing extended configuration space. This refactor also allows for the ".bus_shift" initialisers to be dropped when the user is not using a custom value as a default value will be used as per the PCI Express Specification. Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>, and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create() issue with .bus_shift and to Vladimir for proposing the fix. [bhelgaas: incorporate Vladimir's fix, update commit log] Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jon Derrick <jonathan.derrick@intel.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
2020-11-29 23:07:39 +00:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
2023-01-19 19:15:22 -08:00
2023-01-19 19:15:22 -08:00
2023-01-19 19:15:22 -08:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: vmd: Fix wrong kfree() in vmd_msi_free() vmd_msi_alloc() allocates struct vmd_irq and stashes it into irq_data->chip_data associated with the VMD's interrupt domain. vmd_msi_free() extracts the pointer by calling irq_get_chip_data() and frees it. irq_get_chip_data() returns the chip_data associated with the top interrupt domain. This worked in the past because VMD's interrupt domain was the top domain. But d7d8ab87e3e7 ("PCI: vmd: Switch to msi_create_parent_irq_domain()") changed the interrupt domain hierarchy so VMD's interrupt domain is not the top domain anymore. irq_get_chip_data() now returns the chip_data at the MSI devices' interrupt domains. It is therefore broken for vmd_msi_free() to kfree() this chip_data. Fix by extracting the chip_data associated with the VMD's interrupt domain. Fixes: d7d8ab87e3e7 ("PCI: vmd: Switch to msi_create_parent_irq_domain()") Reported-by: Kenneth Crudup <kenny@panix.com> Closes: https://lore.kernel.org/linux-pci/dfa40e48-8840-4e61-9fda-25cdb3ad81c1@panix.com/ Reported-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Closes: https://lore.kernel.org/linux-pci/ed53280ed15d1140700b96cca2734bf327ee92539e5eb68e80f5bbbf0f01@linux.gnuweeb.org/ Tested-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Tested-by: Kenneth Crudup <kenny@panix.com> Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com> Acked-by: Manivannan Sadhasivam <mani@kernel.org> Link: https://patch.msgid.link/20250807081051.2253962-1-namcao@linutronix.de
2025-08-07 10:10:51 +02:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: vmd: Fix wrong kfree() in vmd_msi_free() vmd_msi_alloc() allocates struct vmd_irq and stashes it into irq_data->chip_data associated with the VMD's interrupt domain. vmd_msi_free() extracts the pointer by calling irq_get_chip_data() and frees it. irq_get_chip_data() returns the chip_data associated with the top interrupt domain. This worked in the past because VMD's interrupt domain was the top domain. But d7d8ab87e3e7 ("PCI: vmd: Switch to msi_create_parent_irq_domain()") changed the interrupt domain hierarchy so VMD's interrupt domain is not the top domain anymore. irq_get_chip_data() now returns the chip_data at the MSI devices' interrupt domains. It is therefore broken for vmd_msi_free() to kfree() this chip_data. Fix by extracting the chip_data associated with the VMD's interrupt domain. Fixes: d7d8ab87e3e7 ("PCI: vmd: Switch to msi_create_parent_irq_domain()") Reported-by: Kenneth Crudup <kenny@panix.com> Closes: https://lore.kernel.org/linux-pci/dfa40e48-8840-4e61-9fda-25cdb3ad81c1@panix.com/ Reported-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Closes: https://lore.kernel.org/linux-pci/ed53280ed15d1140700b96cca2734bf327ee92539e5eb68e80f5bbbf0f01@linux.gnuweeb.org/ Tested-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Tested-by: Kenneth Crudup <kenny@panix.com> Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com> Acked-by: Manivannan Sadhasivam <mani@kernel.org> Link: https://patch.msgid.link/20250807081051.2253962-1-namcao@linutronix.de
2025-08-07 10:10:51 +02:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: Unify ECAM constants in native PCI Express drivers Add ECAM-related constants to provide a set of standard constants defining memory address shift values to the byte-level address that can be used to access the PCI Express Configuration Space, and then move native PCI Express controller drivers to use the newly introduced definitions retiring driver-specific ones. Refactor pci_ecam_map_bus() function to use newly added constants so that limits to the bus, device function and offset (now limited to 4K as per the specification) are in place to prevent the defective or malicious caller from supplying incorrect configuration offset and thus targeting the wrong device when accessing extended configuration space. This refactor also allows for the ".bus_shift" initialisers to be dropped when the user is not using a custom value as a default value will be used as per the PCI Express Specification. Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>, and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create() issue with .bus_shift and to Vladimir for proposing the fix. [bhelgaas: incorporate Vladimir's fix, update commit log] Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jon Derrick <jonathan.derrick@intel.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
2020-11-29 23:07:39 +00:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: Unify ECAM constants in native PCI Express drivers Add ECAM-related constants to provide a set of standard constants defining memory address shift values to the byte-level address that can be used to access the PCI Express Configuration Space, and then move native PCI Express controller drivers to use the newly introduced definitions retiring driver-specific ones. Refactor pci_ecam_map_bus() function to use newly added constants so that limits to the bus, device function and offset (now limited to 4K as per the specification) are in place to prevent the defective or malicious caller from supplying incorrect configuration offset and thus targeting the wrong device when accessing extended configuration space. This refactor also allows for the ".bus_shift" initialisers to be dropped when the user is not using a custom value as a default value will be used as per the PCI Express Specification. Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>, and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create() issue with .bus_shift and to Vladimir for proposing the fix. [bhelgaas: incorporate Vladimir's fix, update commit log] Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jon Derrick <jonathan.derrick@intel.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
2020-11-29 23:07:39 +00:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: Unify ECAM constants in native PCI Express drivers Add ECAM-related constants to provide a set of standard constants defining memory address shift values to the byte-level address that can be used to access the PCI Express Configuration Space, and then move native PCI Express controller drivers to use the newly introduced definitions retiring driver-specific ones. Refactor pci_ecam_map_bus() function to use newly added constants so that limits to the bus, device function and offset (now limited to 4K as per the specification) are in place to prevent the defective or malicious caller from supplying incorrect configuration offset and thus targeting the wrong device when accessing extended configuration space. This refactor also allows for the ".bus_shift" initialisers to be dropped when the user is not using a custom value as a default value will be used as per the PCI Express Specification. Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>, and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create() issue with .bus_shift and to Vladimir for proposing the fix. [bhelgaas: incorporate Vladimir's fix, update commit log] Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jon Derrick <jonathan.derrick@intel.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
2020-11-29 23:07:39 +00:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: vmd: Disable bridge window for domain reset During domain reset process vmd_domain_reset() clears PCI configuration space of VMD root ports. But certain platform has observed following errors and failed to boot. ... DMAR: VT-d detected Invalidation Queue Error: Reason f DMAR: VT-d detected Invalidation Time-out Error: SID ffff DMAR: VT-d detected Invalidation Completion Error: SID ffff DMAR: QI HEAD: UNKNOWN qw0 = 0x0, qw1 = 0x0 DMAR: QI PRIOR: UNKNOWN qw0 = 0x0, qw1 = 0x0 DMAR: Invalidation Time-out Error (ITE) cleared The root cause is that memset_io() clears prefetchable memory base/limit registers and prefetchable base/limit 32 bits registers sequentially. This seems to be enabling prefetchable memory if the device disabled prefetchable memory originally. Here is an example (before memset_io()): PCI configuration space for 10000:00:00.0: 86 80 30 20 06 00 10 00 04 00 04 06 00 00 01 00 00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 20 00 00 00 00 01 00 01 00 ff ff ff ff 75 05 00 00 ... So, prefetchable memory is ffffffff00000000-575000fffff, which is disabled. When memset_io() clears prefetchable base 32 bits register, the prefetchable memory becomes 0000000000000000-575000fffff, which is enabled and incorrect. Here is the quote from section 7.5.1.3.9 of PCI Express Base 6.0 spec: The Prefetchable Memory Limit register must be programmed to a smaller value than the Prefetchable Memory Base register if there is no prefetchable memory on the secondary side of the bridge. This is believed to be the reason for the failure and in addition the sequence of operation in vmd_domain_reset() is not following the PCIe specs. Disable the bridge window by executing a sequence of operations borrowed from pci_disable_bridge_window() and pci_setup_bridge_io(), that comply with the PCI specifications. Link: https://lore.kernel.org/r/20230810215029.1177379-1-nirmal.patel@linux.intel.com Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2023-08-10 17:50:29 -04:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
2023-01-19 19:15:22 -08:00
2023-01-19 19:15:22 -08:00
2023-01-19 19:15:22 -08:00
2023-01-19 19:15:22 -08:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: vmd: Create domain symlink before pci_bus_add_devices() The vmd driver creates a "domain" symlink in sysfs for each VMD bridge. Previously this symlink was created after pci_bus_add_devices() added devices below the VMD bridge and emitted udev events to announce them to userspace. This led to a race between userspace consumers of the udev events and the kernel creation of the symlink. One such consumer is mdadm, which assembles block devices into a RAID array, and for devices below a VMD bridge, mdadm depends on the "domain" symlink. If mdadm loses the race, it may be unable to assemble a RAID array, which may cause a boot failure or other issues, with complaints like this: (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: Unable to get real path for '/sys/bus/pci/drivers/vmd/0000:c7:00.5/domain/device'' (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: /dev/nvme1n1 is not attached to Intel(R) RAID controller.' (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: No OROM/EFI properties for /dev/nvme1n1' (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: no RAID superblock on /dev/nvme1n1.' (udev-worker)[2149]: nvme1n1: Process '/sbin/mdadm -I /dev/nvme1n1' failed with exit code 1. This symptom prevents the OS from booting successfully. After a NVMe disk is probed/added by the nvme driver, udevd invokes mdadm to detect if there is a mdraid associated with this NVMe disk, and mdadm determines if a NVMe device is connected to a particular VMD domain by checking the "domain" symlink. For example: Thread A Thread B Thread mdadm vmd_enable_domain pci_bus_add_devices __driver_probe_device ... work_on_cpu schedule_work_on : wakeup Thread B nvme_probe : wakeup scan_work to scan nvme disk and add nvme disk then wakeup udevd : udevd executes mdadm command flush_work main : wait for nvme_probe done ... __driver_probe_device find_driver_devices : probe next nvme device : 1) Detect domain symlink ... 2) Find domain symlink ... from vmd sysfs ... 3) Domain symlink not ... created yet; failed sysfs_create_link : create domain symlink Create the VMD "domain" symlink before invoking pci_bus_add_devices() to avoid this race. Suggested-by: Adrian Huang <ahuang12@lenovo.com> Link: https://lore.kernel.org/linux-pci/20240605124844.24293-1-sjiwei@163.com Signed-off-by: Jiwei Sun <sunjw10@lenovo.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> [bhelgaas: commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
2024-06-05 20:48:44 +08:00
2023-01-19 19:15:22 -08:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
PCI: vmd: Create domain symlink before pci_bus_add_devices() The vmd driver creates a "domain" symlink in sysfs for each VMD bridge. Previously this symlink was created after pci_bus_add_devices() added devices below the VMD bridge and emitted udev events to announce them to userspace. This led to a race between userspace consumers of the udev events and the kernel creation of the symlink. One such consumer is mdadm, which assembles block devices into a RAID array, and for devices below a VMD bridge, mdadm depends on the "domain" symlink. If mdadm loses the race, it may be unable to assemble a RAID array, which may cause a boot failure or other issues, with complaints like this: (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: Unable to get real path for '/sys/bus/pci/drivers/vmd/0000:c7:00.5/domain/device'' (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: /dev/nvme1n1 is not attached to Intel(R) RAID controller.' (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: No OROM/EFI properties for /dev/nvme1n1' (udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: no RAID superblock on /dev/nvme1n1.' (udev-worker)[2149]: nvme1n1: Process '/sbin/mdadm -I /dev/nvme1n1' failed with exit code 1. This symptom prevents the OS from booting successfully. After a NVMe disk is probed/added by the nvme driver, udevd invokes mdadm to detect if there is a mdraid associated with this NVMe disk, and mdadm determines if a NVMe device is connected to a particular VMD domain by checking the "domain" symlink. For example: Thread A Thread B Thread mdadm vmd_enable_domain pci_bus_add_devices __driver_probe_device ... work_on_cpu schedule_work_on : wakeup Thread B nvme_probe : wakeup scan_work to scan nvme disk and add nvme disk then wakeup udevd : udevd executes mdadm command flush_work main : wait for nvme_probe done ... __driver_probe_device find_driver_devices : probe next nvme device : 1) Detect domain symlink ... 2) Find domain symlink ... from vmd sysfs ... 3) Domain symlink not ... created yet; failed sysfs_create_link : create domain symlink Create the VMD "domain" symlink before invoking pci_bus_add_devices() to avoid this race. Suggested-by: Adrian Huang <ahuang12@lenovo.com> Link: https://lore.kernel.org/linux-pci/20240605124844.24293-1-sjiwei@163.com Signed-off-by: Jiwei Sun <sunjw10@lenovo.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> [bhelgaas: commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
2024-06-05 20:48:44 +08:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
x86/PCI: Add driver for Intel Volume Management Device (VMD) The Intel Volume Management Device (VMD) is a Root Complex Integrated Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can reassign one or more Root Ports to appear within a VMD domain instead of the primary domain. The immediate benefit is that additional PCIe domains allow more than 256 buses in a system by letting bus numbers be reused across different domains. VMD domains do not define ACPI _SEG, so to avoid domain clashing with host bridges defining this segment, VMD domains start at 0x10000, which is greater than the highest possible 16-bit ACPI defined _SEG. This driver enumerates and enables the domain using the root bus configuration interface provided by the PCI subsystem. The driver provides configuration space accessor functions (pci_ops), bus and memory resources, an MSI IRQ domain with irq_chip implementation, and DMA operations necessary to use devices through the VMD endpoint's interface. VMD routes I/O as follows: 1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base address and size for configuration space register access to VMD-owned root ports. It works similarly to MMCONFIG for extended configuration space. Bus numbering is independent and does not conflict with the primary domain. 2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the base address, size, and type for MMIO register access. These addresses are not translated by VMD hardware; they are simply reservations to be distributed to root ports' memory base/limit registers and subdivided among devices downstream. 3) DMA: To interact appropriately with an IOMMU, the source ID DMA read and write requests are translated to the bus-device-function of the VMD endpoint. Otherwise, DMA operates normally without VMD-specific address translation. 4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and PBA. MSIs from VMD domain devices and ports are remapped to appear as if they were issued using one of VMD's MSI-X table entries. Each MSI and MSI-X address of VMD-owned devices and ports has a special format where the address refers to specific entries in the VMD's MSI-X table. As with DMA, the interrupt source ID is translated to VMD's bus-device-function. The driver provides its own MSI and MSI-X configuration functions specific to how MSI messages are used within the VMD domain, and provides an irq_chip for independent IRQ allocation to relay interrupts from VMD's interrupt handler to the appropriate device driver's handler. 5) Errors: PCIe error message are intercepted by the root ports normally (e.g., AER), except with VMD, system errors (i.e., firmware first) are disabled by default. AER and hotplug interrupts are translated in the same way as endpoint interrupts. 6) VMD does not support INTx interrupts or IO ports. Devices or drivers requiring these features should either not be placed below VMD-owned root ports, or VMD should be disabled by BIOS for such endpoints. [bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD resource setup, whitespace, changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00