linux/include/uapi/linux/rtnetlink.h

697 lines
17 KiB

rtnetlink: add new RTM_GETSTATS message to dump link stats This patch adds a new RTM_GETSTATS message to query link stats via netlink from the kernel. RTM_NEWLINK also dumps stats today, but RTM_NEWLINK returns a lot more than just stats and is expensive in some cases when frequent polling for stats from userspace is a common operation. RTM_GETSTATS is an attempt to provide a light weight netlink message to explicity query only link stats from the kernel on an interface. The idea is to also keep it extensible so that new kinds of stats can be added to it in the future. This patch adds the following attribute for NETDEV stats: struct nla_policy ifla_stats_policy[IFLA_STATS_MAX + 1] = { [IFLA_STATS_LINK_64] = { .len = sizeof(struct rtnl_link_stats64) }, }; Like any other rtnetlink message, RTM_GETSTATS can be used to get stats of a single interface or all interfaces with NLM_F_DUMP. Future possible new types of stat attributes: link af stats: - IFLA_STATS_LINK_IPV6 (nested. for ipv6 stats) - IFLA_STATS_LINK_MPLS (nested. for mpls/mdev stats) extended stats: - IFLA_STATS_LINK_EXTENDED (nested. extended software netdev stats like bridge, vlan, vxlan etc) - IFLA_STATS_LINK_HW_EXTENDED (nested. extended hardware stats which are available via ethtool today) This patch also declares a filter mask for all stat attributes. User has to provide a mask of stats attributes to query. filter mask can be specified in the new hdr 'struct if_stats_msg' for stats messages. Other important field in the header is the ifindex. This api can also include attributes for global stats (eg tcp) in the future. When global stats are included in a stats msg, the ifindex in the header must be zero. A single stats message cannot contain both global and netdev specific stats. To easily distinguish them, netdev specific stat attributes name are prefixed with IFLA_STATS_LINK_ Without any attributes in the filter_mask, no stats will be returned. This patch has been tested with mofified iproute2 ifstat. Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-20 08:43:43 -07:00
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-03 19:13:56 -06:00
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-03 19:13:56 -06:00
tcp: introduce a per-route knob for quick ack In previous discussions, I tried to find some reasonable heuristics for delayed ACK, however this seems not possible, according to Eric: "ACKS might also be delayed because of bidirectional traffic, and is more controlled by the application response time. TCP stack can not easily estimate it." "ACK can be incredibly useful to recover from losses in a short time. The vast majority of TCP sessions are small lived, and we send one ACK per received segment anyway at beginning or retransmits to let the sender smoothly increase its cwnd, so an auto-tuning facility wont help them that much." and according to David: "ACKs are the only information we have to detect loss. And, for the same reasons that TCP VEGAS is fundamentally broken, we cannot measure the pipe or some other receiver-side-visible piece of information to determine when it's "safe" to stretch ACK. And even if it's "safe", we should not do it so that losses are accurately detected and we don't spuriously retransmit. The only way to know when the bandwidth increases is to "test" it, by sending more and more packets until drops happen. That's why all successful congestion control algorithms must operate on explicited tested pieces of information. Similarly, it's not really possible to universally know if it's safe to stretch ACK or not." It still makes sense to enable or disable quick ack mode like what TCP_QUICK_ACK does. Similar to TCP_QUICK_ACK option, but for people who can't modify the source code and still wants to control TCP delayed ACK behavior. As David suggested, this should belong to per-path scope, since different pathes may want different behaviors. Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Rick Jones <rick.jones2@hp.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Thomas Graf <tgraf@suug.ch> CC: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-15 09:39:18 +08:00