linux/drivers/hid/hid-core.c

2560 lines
63 KiB

HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
treewide: kmalloc() -> kmalloc_array() The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 13:55:00 -07:00
HID: Fix unit exponent parsing again Revert some changes done in 774638386826621c984ab6994439f474709cac5e. Revert all changes done in hidinput_calc_abs_res as it mistakingly used "Unit" item exponent nibbles to affect resolution value. This wasn't breaking resolution calculation of relevant axes of any existing devices, though, as they have only one dimension to their units and thus 1 in the corresponding nible. Revert to reading "Unit Exponent" item value as a signed integer in hid_parser_global to fix reading specification-complying values. This fixes resolution calculation of devices complying to the HID standard, including Huion, KYE, Waltop and UC-Logic graphics tablets which have their report descriptors fixed by the drivers. Explanations follow. There are two "unit exponents" in HID specification and it is important not to mix them. One is the global "Unit Exponent" item and another is nibble values in the global "Unit" item. See 6.2.2.7 Global Items. The "Unit Exponent" value is just a signed integer and is used to scale the integer resolution unit values, so fractions can be expressed. The nibbles of "Unit" value are used to select the unit system (nibble 0), and presence of a particular basic unit type in the unit formula and its *exponent* (or power, nibbles 1-6). And yes, the latter is in two complement and zero means absence of the unit type. Taking the representation example of (integer) joules from the specification: [mass(grams)][length(centimeters)^2][time(seconds)^-2] * 10^-7 the "Unit Exponent" would be -7 (or 0xF9, if stored as a byte) and the "Unit" value would be 0xE121, signifying: Nibble Part Value Meaning ----- ---- ----- ------- 0 System 1 SI Linear 1 Length 2 Centimeters^2 2 Mass 1 Grams 3 Time -2 Seconds^-2 To give the resolution in e.g. hundredth of joules the "Unit Exponent" item value should have been -9. See also the examples of "Unit" values for some common units in the same chapter. However, there is a common misunderstanding about the "Unit Exponent" value encoding, where it is assumed to be stored the same as nibbles in "Unit" item. This is most likely due to the specification being a bit vague and overloading the term "unit exponent". This also was and still is proliferated by the official "HID Descriptor Tool", which makes this mistake and stores "Unit Exponent" as such. This format is also mentioned in books such as "USB Complete" and in Microsoft's hardware design guides. As a result many devices currently on the market use this encoding and so the driver should support them. Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-10-13 15:09:52 +03:00
HID: Fix unit exponent parsing again Revert some changes done in 774638386826621c984ab6994439f474709cac5e. Revert all changes done in hidinput_calc_abs_res as it mistakingly used "Unit" item exponent nibbles to affect resolution value. This wasn't breaking resolution calculation of relevant axes of any existing devices, though, as they have only one dimension to their units and thus 1 in the corresponding nible. Revert to reading "Unit Exponent" item value as a signed integer in hid_parser_global to fix reading specification-complying values. This fixes resolution calculation of devices complying to the HID standard, including Huion, KYE, Waltop and UC-Logic graphics tablets which have their report descriptors fixed by the drivers. Explanations follow. There are two "unit exponents" in HID specification and it is important not to mix them. One is the global "Unit Exponent" item and another is nibble values in the global "Unit" item. See 6.2.2.7 Global Items. The "Unit Exponent" value is just a signed integer and is used to scale the integer resolution unit values, so fractions can be expressed. The nibbles of "Unit" value are used to select the unit system (nibble 0), and presence of a particular basic unit type in the unit formula and its *exponent* (or power, nibbles 1-6). And yes, the latter is in two complement and zero means absence of the unit type. Taking the representation example of (integer) joules from the specification: [mass(grams)][length(centimeters)^2][time(seconds)^-2] * 10^-7 the "Unit Exponent" would be -7 (or 0xF9, if stored as a byte) and the "Unit" value would be 0xE121, signifying: Nibble Part Value Meaning ----- ---- ----- ------- 0 System 1 SI Linear 1 Length 2 Centimeters^2 2 Mass 1 Grams 3 Time -2 Seconds^-2 To give the resolution in e.g. hundredth of joules the "Unit Exponent" item value should have been -9. See also the examples of "Unit" values for some common units in the same chapter. However, there is a common misunderstanding about the "Unit Exponent" value encoding, where it is assumed to be stored the same as nibbles in "Unit" item. This is most likely due to the specification being a bit vague and overloading the term "unit exponent". This also was and still is proliferated by the official "HID Descriptor Tool", which makes this mistake and stores "Unit Exponent" as such. This format is also mentioned in books such as "USB Complete" and in Microsoft's hardware design guides. As a result many devices currently on the market use this encoding and so the driver should support them. Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-10-13 15:09:52 +03:00
2017-06-09 13:15:37 +02:00
treewide: kmalloc() -> kmalloc_array() The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 13:55:00 -07:00
HID: fix data access in implement() implement() is setting bytes in LE data stream. In case the data is not aligned to 64bits, it reads past the allocated buffer. It doesn't really change any value there (it's properly bitmasked), but in case that this read past the boundary hits a page boundary, pagefault happens when accessing 64bits of 'x' in implement(), and kernel oopses. This happens much more often when numbered reports are in use, as the initial 8bit skip in the buffer makes the whole process work on values which are not aligned to 64bits. This problem dates back to attempts in 2005 and 2006 to make implement() and extract() as generic as possible, and even back then the problem was realized by Adam Kroperlin, but falsely assumed to be impossible to cause any harm: http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg47690.html I have made several attempts at fixing it "on the spot" directly in implement(), but the results were horrible; the special casing for processing last 64bit chunk and switching to different math makes it unreadable mess. I therefore took a path to allocate a few bytes more which will never make it into final report, but are there as a cushion for all the 64bit math operations happening in implement() and extract(). All callers of hid_output_report() are converted at the same time to allocate the buffer by newly introduced hid_alloc_report_buf() helper. Bruno noticed that the whole raw_size test can be dropped as well, as hid_alloc_report_buf() makes sure that the buffer is always of a proper size. Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-07-10 19:56:27 +02:00
HID: fix data access in implement() implement() is setting bytes in LE data stream. In case the data is not aligned to 64bits, it reads past the allocated buffer. It doesn't really change any value there (it's properly bitmasked), but in case that this read past the boundary hits a page boundary, pagefault happens when accessing 64bits of 'x' in implement(), and kernel oopses. This happens much more often when numbered reports are in use, as the initial 8bit skip in the buffer makes the whole process work on values which are not aligned to 64bits. This problem dates back to attempts in 2005 and 2006 to make implement() and extract() as generic as possible, and even back then the problem was realized by Adam Kroperlin, but falsely assumed to be impossible to cause any harm: http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg47690.html I have made several attempts at fixing it "on the spot" directly in implement(), but the results were horrible; the special casing for processing last 64bit chunk and switching to different math makes it unreadable mess. I therefore took a path to allocate a few bytes more which will never make it into final report, but are there as a cushion for all the 64bit math operations happening in implement() and extract(). All callers of hid_output_report() are converted at the same time to allocate the buffer by newly introduced hid_alloc_report_buf() helper. Bruno noticed that the whole raw_size test can be dropped as well, as hid_alloc_report_buf() makes sure that the buffer is always of a proper size. Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-07-10 19:56:27 +02:00
HID: fix data access in implement() implement() is setting bytes in LE data stream. In case the data is not aligned to 64bits, it reads past the allocated buffer. It doesn't really change any value there (it's properly bitmasked), but in case that this read past the boundary hits a page boundary, pagefault happens when accessing 64bits of 'x' in implement(), and kernel oopses. This happens much more often when numbered reports are in use, as the initial 8bit skip in the buffer makes the whole process work on values which are not aligned to 64bits. This problem dates back to attempts in 2005 and 2006 to make implement() and extract() as generic as possible, and even back then the problem was realized by Adam Kroperlin, but falsely assumed to be impossible to cause any harm: http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg47690.html I have made several attempts at fixing it "on the spot" directly in implement(), but the results were horrible; the special casing for processing last 64bit chunk and switching to different math makes it unreadable mess. I therefore took a path to allocate a few bytes more which will never make it into final report, but are there as a cushion for all the 64bit math operations happening in implement() and extract(). All callers of hid_output_report() are converted at the same time to allocate the buffer by newly introduced hid_alloc_report_buf() helper. Bruno noticed that the whole raw_size test can be dropped as well, as hid_alloc_report_buf() makes sure that the buffer is always of a proper size. Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-07-10 19:56:27 +02:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Fix race condition between driver core and ll-driver HID low level drivers register new devices with the HID core which then adds the devices to the HID bus. The HID bus normally immediately probes an appropriate driver which then handles HID input for this device. The ll driver now uses the hid_input_report() function to report input events for a specific device. However, if the HID bus unloads the driver at the same time (for instance via a call to /sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be used by hid_input_report() and hid_device_remove() at the same time which may cause hdev->driver to point to invalid memory. This fix adds a semaphore to every hid device which protects hdev->driver from asynchronous access. This semaphore is locked during driver *_probe and *_remove and also inside hid_input_report(). The *_probe and *_remove functions may sleep so the semaphore is good here, however, hid_input_report() is in atomic context and hence only uses down_trylock(). If it cannot acquire the lock it simply drops the input package. The low-level drivers report input events synchronously so hid_input_report() should never be entered twice at the same time on the same device. Hence, the lock should always be available. But if the driver is currently probed/removed then the lock is not available and dropping the package should be safe because this is what would have happened if the package arrived some milliseconds earlier/later. This also fixes another race condition while probing drivers: First the *_probe function of the driver is called and only if that succeeds, the related input device of hidinput is registered. If the low level driver reports input events after the *_probe function returned but before the input device is registered, then a NULL pointer dereference will occur. (Equivalently on driver remove function). This is not possible anymore, since the semaphore lock drops all incoming packages until the driver/device is fully initialized. Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-08-10 14:02:07 +02:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00
HID: debug: fix RCU preemption issue Commit 2353f2bea ("HID: protect hid_debug_list") introduced mutex locking around debug_list access to prevent SMP races when debugfs nodes are being operated upon by multiple userspace processess. mutex is not a proper synchronization primitive though, as the hid-debug callbacks are being called from atomic contexts. We also have to be careful about disabling IRQs when taking the lock to prevent deadlock against IRQ handlers. Benjamin reports this has also been reported in RH bugzilla as bug #958935. =============================== [ INFO: suspicious RCU usage. ] 3.9.0+ #94 Not tainted ------------------------------- include/linux/rcupdate.h:476 Illegal context switch in RCU read-side critical section! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 4 locks held by Xorg/5502: #0: (&evdev->mutex){+.+...}, at: [<ffffffff81512c3d>] evdev_write+0x6d/0x160 #1: (&(&dev->event_lock)->rlock#2){-.-...}, at: [<ffffffff8150dd9b>] input_inject_event+0x5b/0x230 #2: (rcu_read_lock){.+.+..}, at: [<ffffffff8150dd82>] input_inject_event+0x42/0x230 #3: (&(&usbhid->lock)->rlock){-.....}, at: [<ffffffff81565289>] usb_hidinput_input_event+0x89/0x120 stack backtrace: CPU: 0 PID: 5502 Comm: Xorg Not tainted 3.9.0+ #94 Hardware name: Dell Inc. OptiPlex 390/0M5DCD, BIOS A09 07/24/2012 0000000000000001 ffff8800689c7c38 ffffffff816f249f ffff8800689c7c68 ffffffff810acb1d 0000000000000000 ffffffff81a03ac7 000000000000019d 0000000000000000 ffff8800689c7c90 ffffffff8107cda7 0000000000000000 Call Trace: [<ffffffff816f249f>] dump_stack+0x19/0x1b [<ffffffff810acb1d>] lockdep_rcu_suspicious+0xfd/0x130 [<ffffffff8107cda7>] __might_sleep+0xc7/0x230 [<ffffffff816f7770>] mutex_lock_nested+0x40/0x3a0 [<ffffffff81312ac4>] ? vsnprintf+0x354/0x640 [<ffffffff81553cc4>] hid_debug_event+0x34/0x100 [<ffffffff81554197>] hid_dump_input+0x67/0xa0 [<ffffffff81556430>] hid_set_field+0x50/0x120 [<ffffffff8156529a>] usb_hidinput_input_event+0x9a/0x120 [<ffffffff8150d89e>] input_handle_event+0x8e/0x530 [<ffffffff8150df10>] input_inject_event+0x1d0/0x230 [<ffffffff8150dd82>] ? input_inject_event+0x42/0x230 [<ffffffff81512cae>] evdev_write+0xde/0x160 [<ffffffff81185038>] vfs_write+0xc8/0x1f0 [<ffffffff81185535>] SyS_write+0x55/0xa0 [<ffffffff81704482>] system_call_fastpath+0x16/0x1b BUG: sleeping function called from invalid context at kernel/mutex.c:413 in_atomic(): 1, irqs_disabled(): 1, pid: 5502, name: Xorg INFO: lockdep is turned off. irq event stamp: 1098574 hardirqs last enabled at (1098573): [<ffffffff816fb53f>] _raw_spin_unlock_irqrestore+0x3f/0x70 hardirqs last disabled at (1098574): [<ffffffff816faaf5>] _raw_spin_lock_irqsave+0x25/0xa0 softirqs last enabled at (1098306): [<ffffffff8104971f>] __do_softirq+0x18f/0x3c0 softirqs last disabled at (1097867): [<ffffffff81049ad5>] irq_exit+0xa5/0xb0 CPU: 0 PID: 5502 Comm: Xorg Not tainted 3.9.0+ #94 Hardware name: Dell Inc. OptiPlex 390/0M5DCD, BIOS A09 07/24/2012 ffffffff81a03ac7 ffff8800689c7c68 ffffffff816f249f ffff8800689c7c90 ffffffff8107ce60 0000000000000000 ffff8800689c7fd8 ffff88006a62c800 ffff8800689c7d10 ffffffff816f7770 ffff8800689c7d00 ffffffff81312ac4 Call Trace: [<ffffffff816f249f>] dump_stack+0x19/0x1b [<ffffffff8107ce60>] __might_sleep+0x180/0x230 [<ffffffff816f7770>] mutex_lock_nested+0x40/0x3a0 [<ffffffff81312ac4>] ? vsnprintf+0x354/0x640 [<ffffffff81553cc4>] hid_debug_event+0x34/0x100 [<ffffffff81554197>] hid_dump_input+0x67/0xa0 [<ffffffff81556430>] hid_set_field+0x50/0x120 [<ffffffff8156529a>] usb_hidinput_input_event+0x9a/0x120 [<ffffffff8150d89e>] input_handle_event+0x8e/0x530 [<ffffffff8150df10>] input_inject_event+0x1d0/0x230 [<ffffffff8150dd82>] ? input_inject_event+0x42/0x230 [<ffffffff81512cae>] evdev_write+0xde/0x160 [<ffffffff81185038>] vfs_write+0xc8/0x1f0 [<ffffffff81185535>] SyS_write+0x55/0xa0 [<ffffffff81704482>] system_call_fastpath+0x16/0x1b Reported-by: majianpeng <majianpeng@gmail.com> Reported-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-05-06 13:05:50 +02:00
HID: Separate struct hid_device's driver_lock into two locks. This patch separates struct hid_device's driver_lock into two. The goal is to allow hid device drivers to receive input during their probe() or remove() function calls. This is necessary because some drivers need to communicate with the device to determine parameters needed during probe (e.g., size of a multi-touch surface), and if possible, may perfer to communicate with a device on host-initiated disconnect (e.g., to put it into a low-power state). Historically, three functions used driver_lock: - hid_device_probe: blocks to acquire lock - hid_device_remove: blocks to acquire lock - hid_input_report: if locked returns -EBUSY, else acquires lock This patch adds another lock (driver_input_lock) which is used to block input from occurring. The lock behavior is now: - hid_device_probe: blocks to acq. driver_lock, then driver_input_lock - hid_device_remove: blocks to acq. driver_lock, then driver_input_lock - hid_input_report: if driver_input_lock locked returns -EBUSY, else acquires driver_input_lock This patch also adds two helper functions to be called during probe() or remove(): hid_device_io_start() and hid_device_io_stop(). These functions lock and unlock, respectively, driver_input_lock; they also make a note of whether they did so that hid-core knows if a driver has changed the lock state. This patch results in no behavior change for existing devices and drivers. However, during a probe() or remove() function call in a driver, that driver may now selectively call hid_device_io_start() to let input events come through, then optionally call hid_device_io_stop() to stop them. Signed-off-by: Andrew de los Reyes <adlr@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-02-18 09:20:21 -08:00