linux/include/linux/netlink.h

360 lines
11 KiB

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 15:07:57 +01:00
netlink: Only check file credentials for implicit destinations It was possible to get a setuid root or setcap executable to write to it's stdout or stderr (which has been set made a netlink socket) and inadvertently reconfigure the networking stack. To prevent this we check that both the creator of the socket and the currentl applications has permission to reconfigure the network stack. Unfortunately this breaks Zebra which always uses sendto/sendmsg and creates it's socket without any privileges. To keep Zebra working don't bother checking if the creator of the socket has privilege when a destination address is specified. Instead rely exclusively on the privileges of the sender of the socket. Note from Andy: This is exactly Eric's code except for some comment clarifications and formatting fixes. Neither I nor, I think, anyone else is thrilled with this approach, but I'm hesitant to wait on a better fix since 3.15 is almost here. Note to stable maintainers: This is a mess. An earlier series of patches in 3.15 fix a rather serious security issue (CVE-2014-0181), but they did so in a way that breaks Zebra. The offending series includes: commit aa4cf9452f469f16cea8c96283b641b4576d4a7b Author: Eric W. Biederman <ebiederm@xmission.com> Date: Wed Apr 23 14:28:03 2014 -0700 net: Add variants of capable for use on netlink messages If a given kernel version is missing that series of fixes, it's probably worth backporting it and this patch. if that series is present, then this fix is critical if you care about Zebra. Cc: stable@vger.kernel.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 11:04:00 -07:00
netlink, mmap: fix edge-case leakages in nf queue zero-copy When netlink mmap on receive side is the consumer of nf queue data, it can happen that in some edge cases, we write skb shared info into the user space mmap buffer: Assume a possible rx ring frame size of only 4096, and the network skb, which is being zero-copied into the netlink skb, contains page frags with an overall skb->len larger than the linear part of the netlink skb. skb_zerocopy(), which is generic and thus not aware of the fact that shared info cannot be accessed for such skbs then tries to write and fill frags, thus leaking kernel data/pointers and in some corner cases possibly writing out of bounds of the mmap area (when filling the last slot in the ring buffer this way). I.e. the ring buffer slot is then of status NL_MMAP_STATUS_VALID, has an advertised length larger than 4096, where the linear part is visible at the slot beginning, and the leaked sizeof(struct skb_shared_info) has been written to the beginning of the next slot (also corrupting the struct nl_mmap_hdr slot header incl. status etc), since skb->end points to skb->data + ring->frame_size - NL_MMAP_HDRLEN. The fix adds and lets __netlink_alloc_skb() take the actual needed linear room for the network skb + meta data into account. It's completely irrelevant for non-mmaped netlink sockets, but in case mmap sockets are used, it can be decided whether the available skb_tailroom() is really large enough for the buffer, or whether it needs to internally fallback to a normal alloc_skb(). >From nf queue side, the information whether the destination port is an mmap RX ring is not really available without extra port-to-socket lookup, thus it can only be determined in lower layers i.e. when __netlink_alloc_skb() is called that checks internally for this. I chose to add the extra ldiff parameter as mmap will then still work: We have data_len and hlen in nfqnl_build_packet_message(), data_len is the full length (capped at queue->copy_range) for skb_zerocopy() and hlen some possible part of data_len that needs to be copied; the rem_len variable indicates the needed remaining linear mmap space. The only other workaround in nf queue internally would be after allocation time by f.e. cap'ing the data_len to the skb_tailroom() iff we deal with an mmap skb, but that would 1) expose the fact that we use a mmap skb to upper layers, and 2) trim the skb where we otherwise could just have moved the full skb into the normal receive queue. After the patch, in my test case the ring slot doesn't fit and therefore shows NL_MMAP_STATUS_COPY, where a full skb carries all the data and thus needs to be picked up via recv(). Fixes: 3ab1f683bf8b ("nfnetlink: add support for memory mapped netlink") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-10 02:10:57 +02:00
netlink: fix splat in skb_clone with large messages Since (c05cdb1 netlink: allow large data transfers from user-space), netlink splats if it invokes skb_clone on large netlink skbs since: * skb_shared_info was not correctly initialized. * skb->destructor is not set in the cloned skb. This was spotted by trinity: [ 894.990671] BUG: unable to handle kernel paging request at ffffc9000047b001 [ 894.991034] IP: [<ffffffff81a212c4>] skb_clone+0x24/0xc0 [...] [ 894.991034] Call Trace: [ 894.991034] [<ffffffff81ad299a>] nl_fib_input+0x6a/0x240 [ 894.991034] [<ffffffff81c3b7e6>] ? _raw_read_unlock+0x26/0x40 [ 894.991034] [<ffffffff81a5f189>] netlink_unicast+0x169/0x1e0 [ 894.991034] [<ffffffff81a601e1>] netlink_sendmsg+0x251/0x3d0 Fix it by: 1) introducing a new netlink_skb_clone function that is used in nl_fib_input, that sets our special skb->destructor in the cloned skb. Moreover, handle the release of the large cloned skb head area in the destructor path. 2) not allowing large skbuffs in the netlink broadcast path. I cannot find any reasonable use of the large data transfer using netlink in that path, moreover this helps to skip extra skb_clone handling. I found two more netlink clients that are cloning the skbs, but they are not in the sendmsg path. Therefore, the sole client cloning that I found seems to be the fib frontend. Thanks to Eric Dumazet for helping to address this issue. Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-28 03:04:23 +02:00
bpf: inet_diag: Dump bpf_sk_storages in inet_diag_dump() This patch will dump out the bpf_sk_storages of a sk if the request has the INET_DIAG_REQ_SK_BPF_STORAGES nlattr. An array of SK_DIAG_BPF_STORAGE_REQ_MAP_FD can be specified in INET_DIAG_REQ_SK_BPF_STORAGES to select which bpf_sk_storage to dump. If no map_fd is specified, all bpf_sk_storages of a sk will be dumped. bpf_sk_storages can be added to the system at runtime. It is difficult to find a proper static value for cb->min_dump_alloc. This patch learns the nlattr size required to dump the bpf_sk_storages of a sk. If it happens to be the very first nlmsg of a dump and it cannot fit the needed bpf_sk_storages, it will try to expand the skb by "pskb_expand_head()". Instead of expanding it in inet_sk_diag_fill(), it is expanded at a sleepable context in __inet_diag_dump() so __GFP_DIRECT_RECLAIM can be used. In __inet_diag_dump(), it will retry as long as the skb is empty and the cb->min_dump_alloc becomes larger than before. cb->min_dump_alloc is bounded by KMALLOC_MAX_SIZE. The min_dump_alloc is also changed from 'u16' to 'u32' to accommodate a sk that may have a few large bpf_sk_storages. The updated cb->min_dump_alloc will also be used to allocate the skb in the next dump. This logic already exists in netlink_dump(). Here is the sample output of a locally modified 'ss' and it could be made more readable by using BTF later: [root@arch-fb-vm1 ~]# ss --bpf-map-id 14 --bpf-map-id 13 -t6an 'dst [::1]:8989' State Recv-Q Send-Q Local Address:Port Peer Address:PortProcess ESTAB 0 0 [::1]:51072 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] ESTAB 0 0 [::1]:51070 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] [root@arch-fb-vm1 ~]# ~/devshare/github/iproute2/misc/ss --bpf-maps -t6an 'dst [::1]:8989' State Recv-Q Send-Q Local Address:Port Peer Address:Port Process ESTAB 0 0 [::1]:51072 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] bpf_map_id:12 value:[ 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000... total:65407 ] ESTAB 0 0 [::1]:51070 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] bpf_map_id:12 value:[ 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000... total:65407 ] Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20200225230427.1976129-1-kafai@fb.com
2020-02-25 15:04:27 -08:00
bpf: inet_diag: Dump bpf_sk_storages in inet_diag_dump() This patch will dump out the bpf_sk_storages of a sk if the request has the INET_DIAG_REQ_SK_BPF_STORAGES nlattr. An array of SK_DIAG_BPF_STORAGE_REQ_MAP_FD can be specified in INET_DIAG_REQ_SK_BPF_STORAGES to select which bpf_sk_storage to dump. If no map_fd is specified, all bpf_sk_storages of a sk will be dumped. bpf_sk_storages can be added to the system at runtime. It is difficult to find a proper static value for cb->min_dump_alloc. This patch learns the nlattr size required to dump the bpf_sk_storages of a sk. If it happens to be the very first nlmsg of a dump and it cannot fit the needed bpf_sk_storages, it will try to expand the skb by "pskb_expand_head()". Instead of expanding it in inet_sk_diag_fill(), it is expanded at a sleepable context in __inet_diag_dump() so __GFP_DIRECT_RECLAIM can be used. In __inet_diag_dump(), it will retry as long as the skb is empty and the cb->min_dump_alloc becomes larger than before. cb->min_dump_alloc is bounded by KMALLOC_MAX_SIZE. The min_dump_alloc is also changed from 'u16' to 'u32' to accommodate a sk that may have a few large bpf_sk_storages. The updated cb->min_dump_alloc will also be used to allocate the skb in the next dump. This logic already exists in netlink_dump(). Here is the sample output of a locally modified 'ss' and it could be made more readable by using BTF later: [root@arch-fb-vm1 ~]# ss --bpf-map-id 14 --bpf-map-id 13 -t6an 'dst [::1]:8989' State Recv-Q Send-Q Local Address:Port Peer Address:PortProcess ESTAB 0 0 [::1]:51072 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] ESTAB 0 0 [::1]:51070 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] [root@arch-fb-vm1 ~]# ~/devshare/github/iproute2/misc/ss --bpf-maps -t6an 'dst [::1]:8989' State Recv-Q Send-Q Local Address:Port Peer Address:Port Process ESTAB 0 0 [::1]:51072 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] bpf_map_id:12 value:[ 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000... total:65407 ] ESTAB 0 0 [::1]:51070 [::1]:8989 bpf_map_id:14 value:[ 3feb ] bpf_map_id:13 value:[ 3f ] bpf_map_id:12 value:[ 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000... total:65407 ] Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20200225230427.1976129-1-kafai@fb.com
2020-02-25 15:04:27 -08:00