kernel/linux
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-11-15 19:56:03 +00:00
Code Issues Releases Packages Activity
linux/drivers/input/misc/rb532_button.c

117 lines
2.8 KiB
Raw Normal View History

treewide: Add SPDX license identifier for more missed files Add SPDX license identifiers to all files which: - Have no license information of any form - Have MODULE_LICENCE("GPL*") inside which was used in the initial scan/conversion to ignore the file These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-19 13:08:20 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: remove use of __devinit CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-23 21:38:25 -08:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: rb532_button - switch to using polled mode of input devices We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts rb532_button driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Link: https://lore.kernel.org/r/20191017204217.106453-17-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:33 -07:00
Input: rb532_button - switch to using managed resources Using devm API allows us to clean up error handling paths and drop the remove() method. Link: https://lore.kernel.org/r/20191017204217.106453-16-dmitry.torokhov@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2019-10-29 17:04:25 -07:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS/input: Move RB532 button to GPIO descriptors Convert the Mikrotik RouterBoard RB532 to use GPIO descriptors by defining a software node for the GPIO chip, then register the button platform device with full info passing the GPIO as a device property. This can be used as a base to move more of the RB532 devices over to passing GPIOs using device properties. Use the GPIO_ACTIVE_LOW flag and drop the inversion in the rb532_button_pressed() function. Signed-off-by: Linus Walleij <linusw@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2026-03-28 16:55:47 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: misc - use macro module_platform_driver() Commit 940ab88962bc1aff3273a8356d64577a6e386736 introduced a new macro to save some platform_driver boilerplate code. Use it. Signed-off-by: JJ Ding <dgdunix@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2011-11-29 11:08:40 -08:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00