linux

mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-09-18 18:15:59 +00:00

60 lines

2.3 KiB

Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 15:20:36 -07:00


















[PATCH] Serial: Split 8250 port table Add separate files for the different 8250 ISA-based serial boards. Looking across all the various architectures, it seems reasonable that we can key the availability of the configuration options for these beasts to the bus-related symbols (iow, CONFIG_ISA). We also standardise the base baud/uart clock rate for these boards - I'm sure that isn't architecture specific, but is solely dependent on the crystal fitted on the board (which should be the same no matter what type of machine its fitted into.) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> 2005-06-27 11:12:54 +01:00




[SERIAL] Support Au1x00 8250 UARTs using the generic 8250 driver. The offsets of the registers are in a different place, and some parts cannot handle a full set of modem control signals. Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> 2005-11-06 09:07:03 +00:00
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 15:20:36 -07:00































[PATCH] ioc4: CONFIG split The SGI IOC4 I/O controller chip drivers are currently all configured by CONFIG_BLK_DEV_SGIIOC4. This is undesirable as not all IOC4 hardware features are needed by all systems. This patch adds two configuration variables, CONFIG_SGI_IOC4 for core IOC4 driver support (see patch 1/3 in this series for further explanation) and CONFIG_SERIAL_SGI_IOC4 to independently enable serial port support. Signed-off-by: Brent Casavant <bcasavan@sgi.com> Acked-by: Pat Gefre <pfg@sgi.com> Acked-by: Jeremy Higdon <jeremy@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org> 2005-06-21 17:16:01 -07:00
[PATCH] Altix: ioc3 serial support Add driver support for a 2 port PCI IOC3-based serial card on Altix boxes: This is a re-submission. On the original submission I was asked to organize the code so that the MIPS ioc3 ethernet and serial parts could be used with this driver. Stanislaw Skowronek was kind enough to provide the shim layer for this - thanks Stanislaw. This patch includes the shim layer and the Altix PCI ioc3 serial driver. The MIPS merged ioc3 ethernet and serial support is forthcoming. Signed-off-by: Patrick Gefre <pfg@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org> 2006-01-14 13:20:40 -08:00
[ARM] 3242/2: AT91RM9200 support for 2.6 (Serial) Patch from Andrew Victor This patch adds support to the 2.6 kernel series for the Atmel AT91RM9200 processor. This patch is the Serial driver. This version uses the newly re-written GPL'ed hardware headers. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> 2006-01-10 16:59:27 +00:00

60 lines 2.3 KiB Raw Normal View History

60 lines

2.3 KiB

Raw Normal View History