linux/net/bluetooth/hci_sync.c

6564 lines
170 KiB

Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 1 This make use of hci_cmd_sync_queue for the following MGMT commands: Set Device Class Set Device ID Add UUID Remove UUID tools/mgmt-tester -s "Set Device Class" Test Summary ------------ Set Device Class - Success 1 Passed Set Device Class - Success 2 Passed Set Device Class - Invalid parameters 1 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0599 seconds tools/mgmt-tester -s "Set Device ID" Test Summary ------------ Set Device ID - Success 1 Passed Set Device ID - Success 2 Passed Set Device ID - Disable Passed Set Device ID - Power off and Power on Passed Set Device ID - SSP off and Power on Passed Set Device ID - Invalid Parameter Passed Total: 6, Passed: 6 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.107 seconds tools/mgmt-tester -s "Add UUID" Test Summary ------------ Add UUID - UUID-16 1 Passed Add UUID - UUID-16 multiple 1 Passed Add UUID - UUID-16 partial 1 Passed Add UUID - UUID-32 1 Passed Add UUID - UUID-32 multiple 1 Passed Add UUID - UUID-32 partial 1 Passed Add UUID - UUID-128 1 Passed Add UUID - UUID-128 multiple 1 Passed Add UUID - UUID-128 partial 1 Passed Add UUID - UUID mix Passed Total: 10, Passed: 10 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.198 seconds tools/mgmt-tester -s "Remove UUID" Test Summary ------------ Remove UUID - Success 1 Passed Remove UUID - All UUID - Success 2 Passed Remove UUID - Power Off - Success 3 Passed Remove UUID - Power Off and On - Success 4 Passed Remove UUID - Not Exist - Invalid Params 1 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0908 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:39 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: Fix race condition in hci_cmd_sync_clear There is a potential race condition in hci_cmd_sync_work and hci_cmd_sync_clear, and could lead to use-after-free. For instance, hci_cmd_sync_work is added to the 'req_workqueue' after cancel_work_sync The entry of 'cmd_sync_work_list' may be freed in hci_cmd_sync_clear, and causing kernel panic when it is used in 'hci_cmd_sync_work'. Here's the call trace: dump_stack_lvl+0x49/0x63 print_report.cold+0x5e/0x5d3 ? hci_cmd_sync_work+0x282/0x320 kasan_report+0xaa/0x120 ? hci_cmd_sync_work+0x282/0x320 __asan_report_load8_noabort+0x14/0x20 hci_cmd_sync_work+0x282/0x320 process_one_work+0x77b/0x11c0 ? _raw_spin_lock_irq+0x8e/0xf0 worker_thread+0x544/0x1180 ? poll_idle+0x1e0/0x1e0 kthread+0x285/0x320 ? process_one_work+0x11c0/0x11c0 ? kthread_complete_and_exit+0x30/0x30 ret_from_fork+0x22/0x30 </TASK> Allocated by task 266: kasan_save_stack+0x26/0x50 __kasan_kmalloc+0xae/0xe0 kmem_cache_alloc_trace+0x191/0x350 hci_cmd_sync_queue+0x97/0x2b0 hci_update_passive_scan+0x176/0x1d0 le_conn_complete_evt+0x1b5/0x1a00 hci_le_conn_complete_evt+0x234/0x340 hci_le_meta_evt+0x231/0x4e0 hci_event_packet+0x4c5/0xf00 hci_rx_work+0x37d/0x880 process_one_work+0x77b/0x11c0 worker_thread+0x544/0x1180 kthread+0x285/0x320 ret_from_fork+0x22/0x30 Freed by task 269: kasan_save_stack+0x26/0x50 kasan_set_track+0x25/0x40 kasan_set_free_info+0x24/0x40 ____kasan_slab_free+0x176/0x1c0 __kasan_slab_free+0x12/0x20 slab_free_freelist_hook+0x95/0x1a0 kfree+0xba/0x2f0 hci_cmd_sync_clear+0x14c/0x210 hci_unregister_dev+0xff/0x440 vhci_release+0x7b/0xf0 __fput+0x1f3/0x970 ____fput+0xe/0x20 task_work_run+0xd4/0x160 do_exit+0x8b0/0x22a0 do_group_exit+0xba/0x2a0 get_signal+0x1e4a/0x25b0 arch_do_signal_or_restart+0x93/0x1f80 exit_to_user_mode_prepare+0xf5/0x1a0 syscall_exit_to_user_mode+0x26/0x50 ret_from_fork+0x15/0x30 Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution") Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-03-04 21:50:35 +08:00
Bluetooth: Fix race condition in hci_cmd_sync_clear There is a potential race condition in hci_cmd_sync_work and hci_cmd_sync_clear, and could lead to use-after-free. For instance, hci_cmd_sync_work is added to the 'req_workqueue' after cancel_work_sync The entry of 'cmd_sync_work_list' may be freed in hci_cmd_sync_clear, and causing kernel panic when it is used in 'hci_cmd_sync_work'. Here's the call trace: dump_stack_lvl+0x49/0x63 print_report.cold+0x5e/0x5d3 ? hci_cmd_sync_work+0x282/0x320 kasan_report+0xaa/0x120 ? hci_cmd_sync_work+0x282/0x320 __asan_report_load8_noabort+0x14/0x20 hci_cmd_sync_work+0x282/0x320 process_one_work+0x77b/0x11c0 ? _raw_spin_lock_irq+0x8e/0xf0 worker_thread+0x544/0x1180 ? poll_idle+0x1e0/0x1e0 kthread+0x285/0x320 ? process_one_work+0x11c0/0x11c0 ? kthread_complete_and_exit+0x30/0x30 ret_from_fork+0x22/0x30 </TASK> Allocated by task 266: kasan_save_stack+0x26/0x50 __kasan_kmalloc+0xae/0xe0 kmem_cache_alloc_trace+0x191/0x350 hci_cmd_sync_queue+0x97/0x2b0 hci_update_passive_scan+0x176/0x1d0 le_conn_complete_evt+0x1b5/0x1a00 hci_le_conn_complete_evt+0x234/0x340 hci_le_meta_evt+0x231/0x4e0 hci_event_packet+0x4c5/0xf00 hci_rx_work+0x37d/0x880 process_one_work+0x77b/0x11c0 worker_thread+0x544/0x1180 kthread+0x285/0x320 ret_from_fork+0x22/0x30 Freed by task 269: kasan_save_stack+0x26/0x50 kasan_set_track+0x25/0x40 kasan_set_free_info+0x24/0x40 ____kasan_slab_free+0x176/0x1c0 __kasan_slab_free+0x12/0x20 slab_free_freelist_hook+0x95/0x1a0 kfree+0xba/0x2f0 hci_cmd_sync_clear+0x14c/0x210 hci_unregister_dev+0xff/0x440 vhci_release+0x7b/0xf0 __fput+0x1f3/0x970 ____fput+0xe/0x20 task_work_run+0xd4/0x160 do_exit+0x8b0/0x22a0 do_group_exit+0xba/0x2a0 get_signal+0x1e4a/0x25b0 arch_do_signal_or_restart+0x93/0x1f80 exit_to_user_mode_prepare+0xf5/0x1a0 syscall_exit_to_user_mode+0x26/0x50 ret_from_fork+0x15/0x30 Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution") Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-03-04 21:50:35 +08:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 1 This make use of hci_cmd_sync_queue for the following MGMT commands: Set Device Class Set Device ID Add UUID Remove UUID tools/mgmt-tester -s "Set Device Class" Test Summary ------------ Set Device Class - Success 1 Passed Set Device Class - Success 2 Passed Set Device Class - Invalid parameters 1 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0599 seconds tools/mgmt-tester -s "Set Device ID" Test Summary ------------ Set Device ID - Success 1 Passed Set Device ID - Success 2 Passed Set Device ID - Disable Passed Set Device ID - Power off and Power on Passed Set Device ID - SSP off and Power on Passed Set Device ID - Invalid Parameter Passed Total: 6, Passed: 6 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.107 seconds tools/mgmt-tester -s "Add UUID" Test Summary ------------ Add UUID - UUID-16 1 Passed Add UUID - UUID-16 multiple 1 Passed Add UUID - UUID-16 partial 1 Passed Add UUID - UUID-32 1 Passed Add UUID - UUID-32 multiple 1 Passed Add UUID - UUID-32 partial 1 Passed Add UUID - UUID-128 1 Passed Add UUID - UUID-128 multiple 1 Passed Add UUID - UUID-128 partial 1 Passed Add UUID - UUID mix Passed Total: 10, Passed: 10 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.198 seconds tools/mgmt-tester -s "Remove UUID" Test Summary ------------ Remove UUID - Success 1 Passed Remove UUID - All UUID - Success 2 Passed Remove UUID - Power Off - Success 3 Passed Remove UUID - Power Off and On - Success 4 Passed Remove UUID - Not Exist - Invalid Params 1 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0908 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:39 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: ISO: Support multiple BIGs This adds support for creating multiple BIGs. According to spec, each BIG shall have an unique handle, and each BIG should be associated with a different advertising handle. Otherwise, the LE Create BIG command will fail, with error code Command Disallowed (for reusing a BIG handle), or Unknown Advertising Identifier (for reusing an advertising handle). The btmon snippet below shows an exercise for creating two BIGs for the same controller, by opening two isotest instances with the following command: tools/isotest -i hci0 -s 00:00:00:00:00:00 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31 Handle: 0x00 Advertising Handle: 0x01 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) Status: Success (0x00) Handle: 0x00 BIG Synchronization Delay: 912 us (0x000390) Transport Latency: 912 us (0x000390) PHY: LE 2M (0x02) NSE: 3 BN: 1 PTO: 1 IRC: 3 Maximum PDU: 40 ISO Interval: 10.00 msec (0x0008) Connection Handle #0: 10 < HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) Handle: 0x01 Advertising Handle: 0x02 Number of BIS: 1 SDU Interval: 10000 us (0x002710) Maximum SDU size: 40 Maximum Latency: 10 ms (0x000a) RTN: 0x02 PHY: LE 2M (0x02) Packing: Sequential (0x00) Framing: Unframed (0x00) Encryption: 0x00 Broadcast Code: 00000000000000000000000000000000 > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 17:53:16 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2 This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:40 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
bluetooth: don't use bitmaps for random flag accesses The bluetooth code uses our bitmap infrastructure for the two bits (!) of connection setup flags, and in the process causes odd problems when it converts between a bitmap and just the regular values of said bits. It's completely pointless to do things like bitmap_to_arr32() to convert a bitmap into a u32. It shoudln't have been a bitmap in the first place. The reason to use bitmaps is if you have arbitrary number of bits you want to manage (not two!), or if you rely on the atomicity guarantees of the bitmap setting and clearing. The code could use an "atomic_t" and use "atomic_or/andnot()" to set and clear the bit values, but considering that it then copies the bitmaps around with "bitmap_to_arr32()" and friends, there clearly cannot be a lot of atomicity requirements. So just use a regular integer. In the process, this avoids the warnings about erroneous use of bitmap_from_u64() which were triggered on 32-bit architectures when conversion from a u64 would access two words (and, surprise, surprise, only one word is needed - and indeed overkill - for a 2-bit bitmap). That was always problematic, but the compiler seems to notice it and warn about the invalid pattern only after commit 0a97953fd221 ("lib: add bitmap_{from,to}_arr64") changed the exact implementation details of 'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell. Fixes: fe92ee6425a2 ("Bluetooth: hci_core: Rework hci_conn_params flags") Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/ Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/ Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/ Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Reviewed-by: Yury Norov <yury.norov@gmail.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-06-05 11:51:48 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
2021-10-27 16:58:41 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: hci_sync: Enable advertising when LL privacy is enabled This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:42 -07:00
Bluetooth: HCI: Fix global-out-of-bounds To loop a variable-length array, hci_init_stage_sync(stage) considers that stage[i] is valid as long as stage[i-1].func is valid. Thus, the last element of stage[].func should be intentionally invalid as hci_init0[], le_init2[], and others did. However, amp_init1[] and amp_init2[] have no invalid element, letting hci_init_stage_sync() keep accessing amp_init1[] over its valid range. This patch fixes this by adding {} in the last of amp_init1[] and amp_init2[]. ================================================================== BUG: KASAN: global-out-of-bounds in hci_dev_open_sync ( /v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) Read of size 8 at addr ffffffffaed1ab70 by task kworker/u5:0/1032 CPU: 0 PID: 1032 Comm: kworker/u5:0 Not tainted 6.2.0 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04 Workqueue: hci1 hci_power_on Call Trace: <TASK> dump_stack_lvl (/v6.2-bzimage/lib/dump_stack.c:107 (discriminator 1)) print_report (/v6.2-bzimage/mm/kasan/report.c:307 /v6.2-bzimage/mm/kasan/report.c:417) ? hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) kasan_report (/v6.2-bzimage/mm/kasan/report.c:184 /v6.2-bzimage/mm/kasan/report.c:519) ? hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) ? __pfx_hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:4635) ? mutex_lock (/v6.2-bzimage/./arch/x86/include/asm/atomic64_64.h:190 /v6.2-bzimage/./include/linux/atomic/atomic-long.h:443 /v6.2-bzimage/./include/linux/atomic/atomic-instrumented.h:1781 /v6.2-bzimage/kernel/locking/mutex.c:171 /v6.2-bzimage/kernel/locking/mutex.c:285) ? __pfx_mutex_lock (/v6.2-bzimage/kernel/locking/mutex.c:282) hci_power_on (/v6.2-bzimage/net/bluetooth/hci_core.c:485 /v6.2-bzimage/net/bluetooth/hci_core.c:984) ? __pfx_hci_power_on (/v6.2-bzimage/net/bluetooth/hci_core.c:969) ? read_word_at_a_time (/v6.2-bzimage/./include/asm-generic/rwonce.h:85) ? strscpy (/v6.2-bzimage/./arch/x86/include/asm/word-at-a-time.h:62 /v6.2-bzimage/lib/string.c:161) process_one_work (/v6.2-bzimage/kernel/workqueue.c:2294) worker_thread (/v6.2-bzimage/./include/linux/list.h:292 /v6.2-bzimage/kernel/workqueue.c:2437) ? __pfx_worker_thread (/v6.2-bzimage/kernel/workqueue.c:2379) kthread (/v6.2-bzimage/kernel/kthread.c:376) ? __pfx_kthread (/v6.2-bzimage/kernel/kthread.c:331) ret_from_fork (/v6.2-bzimage/arch/x86/entry/entry_64.S:314) </TASK> The buggy address belongs to the variable: amp_init1+0x30/0x60 The buggy address belongs to the physical page: page:000000003a157ec6 refcount:1 mapcount:0 mapping:0000000000000000 ia flags: 0x200000000001000(reserved|node=0|zone=2) raw: 0200000000001000 ffffea0005054688 ffffea0005054688 000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffffffffaed1aa00: f9 f9 f9 f9 00 00 00 00 f9 f9 f9 f9 00 00 00 00 ffffffffaed1aa80: 00 00 00 00 f9 f9 f9 f9 00 00 00 00 00 00 00 00 >ffffffffaed1ab00: 00 f9 f9 f9 f9 f9 f9 f9 00 00 00 00 00 00 f9 f9 ^ ffffffffaed1ab80: f9 f9 f9 f9 00 00 00 00 f9 f9 f9 f9 00 00 00 f9 ffffffffaed1ac00: f9 f9 f9 f9 00 06 f9 f9 f9 f9 f9 f9 00 00 02 f9 This bug is found by FuzzBT, a modified version of Syzkaller. Other contributors for this bug are Ruoyu Wu and Peng Hui. Fixes: d0b137062b2d ("Bluetooth: hci_sync: Rework init stages") Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-03-20 21:50:18 -04:00
Bluetooth: HCI: Fix global-out-of-bounds To loop a variable-length array, hci_init_stage_sync(stage) considers that stage[i] is valid as long as stage[i-1].func is valid. Thus, the last element of stage[].func should be intentionally invalid as hci_init0[], le_init2[], and others did. However, amp_init1[] and amp_init2[] have no invalid element, letting hci_init_stage_sync() keep accessing amp_init1[] over its valid range. This patch fixes this by adding {} in the last of amp_init1[] and amp_init2[]. ================================================================== BUG: KASAN: global-out-of-bounds in hci_dev_open_sync ( /v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) Read of size 8 at addr ffffffffaed1ab70 by task kworker/u5:0/1032 CPU: 0 PID: 1032 Comm: kworker/u5:0 Not tainted 6.2.0 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04 Workqueue: hci1 hci_power_on Call Trace: <TASK> dump_stack_lvl (/v6.2-bzimage/lib/dump_stack.c:107 (discriminator 1)) print_report (/v6.2-bzimage/mm/kasan/report.c:307 /v6.2-bzimage/mm/kasan/report.c:417) ? hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) kasan_report (/v6.2-bzimage/mm/kasan/report.c:184 /v6.2-bzimage/mm/kasan/report.c:519) ? hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:3154 /v6.2-bzimage/net/bluetooth/hci_sync.c:3343 /v6.2-bzimage/net/bluetooth/hci_sync.c:4418 /v6.2-bzimage/net/bluetooth/hci_sync.c:4609 /v6.2-bzimage/net/bluetooth/hci_sync.c:4689) ? __pfx_hci_dev_open_sync (/v6.2-bzimage/net/bluetooth/hci_sync.c:4635) ? mutex_lock (/v6.2-bzimage/./arch/x86/include/asm/atomic64_64.h:190 /v6.2-bzimage/./include/linux/atomic/atomic-long.h:443 /v6.2-bzimage/./include/linux/atomic/atomic-instrumented.h:1781 /v6.2-bzimage/kernel/locking/mutex.c:171 /v6.2-bzimage/kernel/locking/mutex.c:285) ? __pfx_mutex_lock (/v6.2-bzimage/kernel/locking/mutex.c:282) hci_power_on (/v6.2-bzimage/net/bluetooth/hci_core.c:485 /v6.2-bzimage/net/bluetooth/hci_core.c:984) ? __pfx_hci_power_on (/v6.2-bzimage/net/bluetooth/hci_core.c:969) ? read_word_at_a_time (/v6.2-bzimage/./include/asm-generic/rwonce.h:85) ? strscpy (/v6.2-bzimage/./arch/x86/include/asm/word-at-a-time.h:62 /v6.2-bzimage/lib/string.c:161) process_one_work (/v6.2-bzimage/kernel/workqueue.c:2294) worker_thread (/v6.2-bzimage/./include/linux/list.h:292 /v6.2-bzimage/kernel/workqueue.c:2437) ? __pfx_worker_thread (/v6.2-bzimage/kernel/workqueue.c:2379) kthread (/v6.2-bzimage/kernel/kthread.c:376) ? __pfx_kthread (/v6.2-bzimage/kernel/kthread.c:331) ret_from_fork (/v6.2-bzimage/arch/x86/entry/entry_64.S:314) </TASK> The buggy address belongs to the variable: amp_init1+0x30/0x60 The buggy address belongs to the physical page: page:000000003a157ec6 refcount:1 mapcount:0 mapping:0000000000000000 ia flags: 0x200000000001000(reserved|node=0|zone=2) raw: 0200000000001000 ffffea0005054688 ffffea0005054688 000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffffffffaed1aa00: f9 f9 f9 f9 00 00 00 00 f9 f9 f9 f9 00 00 00 00 ffffffffaed1aa80: 00 00 00 00 f9 f9 f9 f9 00 00 00 00 00 00 00 00 >ffffffffaed1ab00: 00 f9 f9 f9 f9 f9 f9 f9 00 00 00 00 00 00 f9 f9 ^ ffffffffaed1ab80: f9 f9 f9 f9 00 00 00 00 f9 f9 f9 f9 00 00 00 f9 ffffffffaed1ac00: f9 f9 f9 f9 00 06 f9 f9 f9 f9 f9 f9 00 00 02 f9 This bug is found by FuzzBT, a modified version of Syzkaller. Other contributors for this bug are Ruoyu Wu and Peng Hui. Fixes: d0b137062b2d ("Bluetooth: hci_sync: Rework init stages") Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-03-20 21:50:18 -04:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: btusb: Fix CSR clones again by re-adding ERR_DATA_REPORTING quirk A patch series by a Qualcomm engineer essentially removed my quirk/workaround because they thought it was unnecessary. It wasn't, and it broke everything again: https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=* He argues that the quirk is not necessary because the code should check if the dongle says if it's supported or not. The problem is that for these Chinese CSR clones they say that it would work: = New Index: 00:00:00:00:00:00 (Primary,USB,hci0) = Open Index: 00:00:00:00:00:00 < HCI Command: Read Local Version Information (0x04|0x0001) plen 0 > HCI Event: Command Complete (0x0e) plen 12 > [hci0] 11.276039 Read Local Version Information (0x04|0x0001) ncmd 1 Status: Success (0x00) HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810) LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312) Manufacturer: Cambridge Silicon Radio (10) ... < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 68 > [hci0] 11.668030 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 163 entries ... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ... ... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 = Close Index: 00:1A:7D:DA:71:XX So bring it back wholesale. Fixes: 63b1a7dd38bf ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING") Fixes: e168f6900877 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR") Fixes: 766ae2422b43 ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk") Cc: stable@vger.kernel.org Cc: Zijun Hu <quic_zijuhu@quicinc.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-10-29 22:24:52 +02:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: btusb: Fix CSR clones again by re-adding ERR_DATA_REPORTING quirk A patch series by a Qualcomm engineer essentially removed my quirk/workaround because they thought it was unnecessary. It wasn't, and it broke everything again: https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=* He argues that the quirk is not necessary because the code should check if the dongle says if it's supported or not. The problem is that for these Chinese CSR clones they say that it would work: = New Index: 00:00:00:00:00:00 (Primary,USB,hci0) = Open Index: 00:00:00:00:00:00 < HCI Command: Read Local Version Information (0x04|0x0001) plen 0 > HCI Event: Command Complete (0x0e) plen 12 > [hci0] 11.276039 Read Local Version Information (0x04|0x0001) ncmd 1 Status: Success (0x00) HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810) LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312) Manufacturer: Cambridge Silicon Radio (10) ... < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 68 > [hci0] 11.668030 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 163 entries ... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ... ... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 = Close Index: 00:1A:7D:DA:71:XX So bring it back wholesale. Fixes: 63b1a7dd38bf ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING") Fixes: e168f6900877 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR") Fixes: 766ae2422b43 ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk") Cc: stable@vger.kernel.org Cc: Zijun Hu <quic_zijuhu@quicinc.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-10-29 22:24:52 +02:00
Bluetooth: btusb: Fix CSR clones again by re-adding ERR_DATA_REPORTING quirk A patch series by a Qualcomm engineer essentially removed my quirk/workaround because they thought it was unnecessary. It wasn't, and it broke everything again: https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=* He argues that the quirk is not necessary because the code should check if the dongle says if it's supported or not. The problem is that for these Chinese CSR clones they say that it would work: = New Index: 00:00:00:00:00:00 (Primary,USB,hci0) = Open Index: 00:00:00:00:00:00 < HCI Command: Read Local Version Information (0x04|0x0001) plen 0 > HCI Event: Command Complete (0x0e) plen 12 > [hci0] 11.276039 Read Local Version Information (0x04|0x0001) ncmd 1 Status: Success (0x00) HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810) LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312) Manufacturer: Cambridge Silicon Radio (10) ... < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 68 > [hci0] 11.668030 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 163 entries ... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ... ... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 = Close Index: 00:1A:7D:DA:71:XX So bring it back wholesale. Fixes: 63b1a7dd38bf ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING") Fixes: e168f6900877 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR") Fixes: 766ae2422b43 ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk") Cc: stable@vger.kernel.org Cc: Zijun Hu <quic_zijuhu@quicinc.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-10-29 22:24:52 +02:00
2023-05-31 11:04:24 +02:00
2023-05-31 11:04:24 +02:00
Bluetooth: Add support for hci devcoredump Add devcoredump APIs to hci core so that drivers only have to provide the dump skbs instead of managing the synchronization and timeouts. The devcoredump APIs should be used in the following manner: - hci_devcoredump_init is called to allocate the dump. - hci_devcoredump_append is called to append any skbs with dump data OR hci_devcoredump_append_pattern is called to insert a pattern. - hci_devcoredump_complete is called when all dump packets have been sent OR hci_devcoredump_abort is called to indicate an error and cancel an ongoing dump collection. The high level APIs just prepare some skbs with the appropriate data and queue it for the dump to process. Packets part of the crashdump can be intercepted in the driver in interrupt context and forwarded directly to the devcoredump APIs. Internally, there are 5 states for the dump: idle, active, complete, abort and timeout. A devcoredump will only be in active state after it has been initialized. Once active, it accepts data to be appended, patterns to be inserted (i.e. memset) and a completion event or an abort event to generate a devcoredump. The timeout is initialized at the same time the dump is initialized (defaulting to 10s) and will be cleared either when the timeout occurs or the dump is complete or aborted. Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Manish Mandlik <mmandlik@google.com> Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-03-30 09:58:23 -07:00
Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) kthread (kernel/kthread.c:376) ret_from_fork (arch/x86/entry/entry_64.S:314) ================================================================== Fixes: e8907f76544f ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 3") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-19 01:04:31 +03:00
Bluetooth: fix data races in smp_unregister(), smp_del_chan() Previous commit e04480920d1e ("Bluetooth: defer cleanup of resources in hci_unregister_dev()") defers all destructive actions to hci_release_dev() to prevent cocurrent problems like NPD, UAF. However, there are still some exceptions that are ignored. The smp_unregister() in hci_dev_close_sync() (previously in hci_dev_do_close) will release resources like the sensitive channel and the smp_dev objects. Consider the situations the device is detaching or power down while the kernel is still operating on it, the following data race could take place. thread-A hci_dev_close_sync | thread-B read_local_oob_ext_data | hci_dev_unlock() | ... | hci_dev_lock() if (hdev->smp_data) | chan = hdev->smp_data | | chan = hdev->smp_data (3) | hdev->smp_data = NULL (1) | if (!chan || !chan->data) (4) ... | smp = chan->data | smp = chan->data if (smp) | chan->data = NULL (2) | ... | kfree_sensitive(smp) | | // dereference smp trigger UFA That is, the objects hdev->smp_data and chan->data both suffer from the data races. In a preempt-enable kernel, the above schedule (when (3) is before (1) and (4) is before (2)) leads to UAF bugs. It can be reproduced in the latest kernel and below is part of the report: [ 49.097146] ================================================================ [ 49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570 [ 49.097611] Read of size 8 at addr ffff888006528360 by task generate_oob/155 [ 49.097611] [ 49.097611] Call Trace: [ 49.097611] <TASK> [ 49.097611] dump_stack_lvl+0x34/0x44 [ 49.097611] print_address_description.constprop.0+0x1f/0x150 [ 49.097611] ? smp_generate_oob+0x2dd/0x570 [ 49.097611] ? smp_generate_oob+0x2dd/0x570 [ 49.097611] kasan_report.cold+0x7f/0x11b [ 49.097611] ? smp_generate_oob+0x2dd/0x570 [ 49.097611] smp_generate_oob+0x2dd/0x570 [ 49.097611] read_local_oob_ext_data+0x689/0xc30 [ 49.097611] ? hci_event_packet+0xc80/0xc80 [ 49.097611] ? sysvec_apic_timer_interrupt+0x9b/0xc0 [ 49.097611] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 [ 49.097611] ? mgmt_init_hdev+0x1c/0x240 [ 49.097611] ? mgmt_init_hdev+0x28/0x240 [ 49.097611] hci_sock_sendmsg+0x1880/0x1e70 [ 49.097611] ? create_monitor_event+0x890/0x890 [ 49.097611] ? create_monitor_event+0x890/0x890 [ 49.097611] sock_sendmsg+0xdf/0x110 [ 49.097611] __sys_sendto+0x19e/0x270 [ 49.097611] ? __ia32_sys_getpeername+0xa0/0xa0 [ 49.097611] ? kernel_fpu_begin_mask+0x1c0/0x1c0 [ 49.097611] __x64_sys_sendto+0xd8/0x1b0 [ 49.097611] ? syscall_exit_to_user_mode+0x1d/0x40 [ 49.097611] do_syscall_64+0x3b/0x90 [ 49.097611] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 49.097611] RIP: 0033:0x7f5a59f51f64 ... [ 49.097611] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5a59f51f64 [ 49.097611] RDX: 0000000000000007 RSI: 00007f5a59d6ac70 RDI: 0000000000000006 [ 49.097611] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 49.097611] R10: 0000000000000040 R11: 0000000000000246 R12: 00007ffec26916ee [ 49.097611] R13: 00007ffec26916ef R14: 00007f5a59d6afc0 R15: 00007f5a59d6b700 To solve these data races, this patch places the smp_unregister() function in the protected area by the hci_dev_lock(). That is, the smp_unregister() function can not be concurrently executed when operating functions (most of them are mgmt operations in mgmt.c) hold the device lock. This patch is tested with kernel LOCK DEBUGGING enabled. The price from the extended holding time of the device lock is supposed to be low as the smp_unregister() function is fairly short and efficient. Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-02-16 12:37:14 +08:00
Bluetooth: fix data races in smp_unregister(), smp_del_chan() Previous commit e04480920d1e ("Bluetooth: defer cleanup of resources in hci_unregister_dev()") defers all destructive actions to hci_release_dev() to prevent cocurrent problems like NPD, UAF. However, there are still some exceptions that are ignored. The smp_unregister() in hci_dev_close_sync() (previously in hci_dev_do_close) will release resources like the sensitive channel and the smp_dev objects. Consider the situations the device is detaching or power down while the kernel is still operating on it, the following data race could take place. thread-A hci_dev_close_sync | thread-B read_local_oob_ext_data | hci_dev_unlock() | ... | hci_dev_lock() if (hdev->smp_data) | chan = hdev->smp_data | | chan = hdev->smp_data (3) | hdev->smp_data = NULL (1) | if (!chan || !chan->data) (4) ... | smp = chan->data | smp = chan->data if (smp) | chan->data = NULL (2) | ... | kfree_sensitive(smp) | | // dereference smp trigger UFA That is, the objects hdev->smp_data and chan->data both suffer from the data races. In a preempt-enable kernel, the above schedule (when (3) is before (1) and (4) is before (2)) leads to UAF bugs. It can be reproduced in the latest kernel and below is part of the report: [ 49.097146] ================================================================ [ 49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570 [ 49.097611] Read of size 8 at addr ffff888006528360 by task generate_oob/155 [ 49.097611] [ 49.097611] Call Trace: [ 49.097611] <TASK> [ 49.097611] dump_stack_lvl+0x34/0x44 [ 49.097611] print_address_description.constprop.0+0x1f/0x150 [ 49.097611] ? smp_generate_oob+0x2dd/0x570 [ 49.097611] ? smp_generate_oob+0x2dd/0x570 [ 49.097611] kasan_report.cold+0x7f/0x11b [ 49.097611] ? smp_generate_oob+0x2dd/0x570 [ 49.097611] smp_generate_oob+0x2dd/0x570 [ 49.097611] read_local_oob_ext_data+0x689/0xc30 [ 49.097611] ? hci_event_packet+0xc80/0xc80 [ 49.097611] ? sysvec_apic_timer_interrupt+0x9b/0xc0 [ 49.097611] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 [ 49.097611] ? mgmt_init_hdev+0x1c/0x240 [ 49.097611] ? mgmt_init_hdev+0x28/0x240 [ 49.097611] hci_sock_sendmsg+0x1880/0x1e70 [ 49.097611] ? create_monitor_event+0x890/0x890 [ 49.097611] ? create_monitor_event+0x890/0x890 [ 49.097611] sock_sendmsg+0xdf/0x110 [ 49.097611] __sys_sendto+0x19e/0x270 [ 49.097611] ? __ia32_sys_getpeername+0xa0/0xa0 [ 49.097611] ? kernel_fpu_begin_mask+0x1c0/0x1c0 [ 49.097611] __x64_sys_sendto+0xd8/0x1b0 [ 49.097611] ? syscall_exit_to_user_mode+0x1d/0x40 [ 49.097611] do_syscall_64+0x3b/0x90 [ 49.097611] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 49.097611] RIP: 0033:0x7f5a59f51f64 ... [ 49.097611] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5a59f51f64 [ 49.097611] RDX: 0000000000000007 RSI: 00007f5a59d6ac70 RDI: 0000000000000006 [ 49.097611] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 49.097611] R10: 0000000000000040 R11: 0000000000000246 R12: 00007ffec26916ee [ 49.097611] R13: 00007ffec26916ef R14: 00007f5a59d6afc0 R15: 00007f5a59d6b700 To solve these data races, this patch places the smp_unregister() function in the protected area by the hci_dev_lock(). That is, the smp_unregister() function can not be concurrently executed when operating functions (most of them are mgmt operations in mgmt.c) hold the device lock. This patch is tested with kernel LOCK DEBUGGING enabled. The price from the extended holding time of the device lock is supposed to be low as the smp_unregister() function is fairly short and efficient. Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2022-02-16 12:37:14 +08:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
2023-09-30 15:53:32 +03:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
2023-09-30 15:53:32 +03:00
2023-09-30 15:53:32 +03:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
2023-09-30 15:53:32 +03:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
2023-09-30 15:53:32 +03:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
Bluetooth: hci_sync: Fix UAF in hci_disconnect_all_sync Use-after-free can occur in hci_disconnect_all_sync if a connection is deleted by concurrent processing of a controller event. To prevent this the code now tries to iterate over the list backwards to ensure the links are cleanup before its parents, also it no longer relies on a cursor, instead it always uses the last element since hci_abort_conn_sync is guaranteed to call hci_conn_del. UAF crash log: ================================================================== BUG: KASAN: slab-use-after-free in hci_set_powered_sync (net/bluetooth/hci_sync.c:5424) [bluetooth] Read of size 8 at addr ffff888009d9c000 by task kworker/u9:0/124 CPU: 0 PID: 124 Comm: kworker/u9:0 Tainted: G W 6.5.0-rc1+ #10 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> dump_stack_lvl+0x5b/0x90 print_report+0xcf/0x670 ? __virt_addr_valid+0xdd/0x160 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] kasan_report+0xa6/0xe0 ? hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_set_powered_sync+0x2c9/0x4a0 [bluetooth] ? __pfx_hci_set_powered_sync+0x10/0x10 [bluetooth] ? __pfx_lock_release+0x10/0x10 ? __pfx_set_powered_sync+0x10/0x10 [bluetooth] hci_cmd_sync_work+0x137/0x220 [bluetooth] process_one_work+0x526/0x9d0 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? mark_held_locks+0x1a/0x90 worker_thread+0x92/0x630 ? __pfx_worker_thread+0x10/0x10 kthread+0x196/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2c/0x50 </TASK> Allocated by task 1782: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 __kasan_kmalloc+0x8f/0xa0 hci_conn_add+0xa5/0xa80 [bluetooth] hci_bind_cis+0x881/0x9b0 [bluetooth] iso_connect_cis+0x121/0x520 [bluetooth] iso_sock_connect+0x3f6/0x790 [bluetooth] __sys_connect+0x109/0x130 __x64_sys_connect+0x40/0x50 do_syscall_64+0x60/0x90 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 695: kasan_save_stack+0x33/0x60 kasan_set_track+0x25/0x30 kasan_save_free_info+0x2b/0x50 __kasan_slab_free+0x10a/0x180 __kmem_cache_free+0x14d/0x2e0 device_release+0x5d/0xf0 kobject_put+0xdf/0x270 hci_disconn_complete_evt+0x274/0x3a0 [bluetooth] hci_event_packet+0x579/0x7e0 [bluetooth] hci_rx_work+0x287/0xaa0 [bluetooth] process_one_work+0x526/0x9d0 worker_thread+0x92/0x630 kthread+0x196/0x1e0 ret_from_fork+0x2c/0x50 ================================================================== Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-09 16:49:33 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2021-10-27 16:58:45 -07:00
bluetooth: don't use bitmaps for random flag accesses The bluetooth code uses our bitmap infrastructure for the two bits (!) of connection setup flags, and in the process causes odd problems when it converts between a bitmap and just the regular values of said bits. It's completely pointless to do things like bitmap_to_arr32() to convert a bitmap into a u32. It shoudln't have been a bitmap in the first place. The reason to use bitmaps is if you have arbitrary number of bits you want to manage (not two!), or if you rely on the atomicity guarantees of the bitmap setting and clearing. The code could use an "atomic_t" and use "atomic_or/andnot()" to set and clear the bit values, but considering that it then copies the bitmaps around with "bitmap_to_arr32()" and friends, there clearly cannot be a lot of atomicity requirements. So just use a regular integer. In the process, this avoids the warnings about erroneous use of bitmap_from_u64() which were triggered on 32-bit architectures when conversion from a u64 would access two words (and, surprise, surprise, only one word is needed - and indeed overkill - for a 2-bit bitmap). That was always problematic, but the compiler seems to notice it and warn about the invalid pattern only after commit 0a97953fd221 ("lib: add bitmap_{from,to}_arr64") changed the exact implementation details of 'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell. Fixes: fe92ee6425a2 ("Bluetooth: hci_core: Rework hci_conn_params flags") Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/ Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/ Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/ Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Reviewed-by: Yury Norov <yury.norov@gmail.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-06-05 11:51:48 -07:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: ISO: do not emit new LE Create CIS if previous is pending LE Create CIS command shall not be sent before all CIS Established events from its previous invocation have been processed. Currently it is sent via hci_sync but that only waits for the first event, but there can be multiple. Make it wait for all events, and simplify the CIS creation as follows: Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been sent for the connection but it is not yet completed. Make BT_CONNECT state to mean the connection wants Create CIS. On events after which new Create CIS may need to be sent, send it if possible and some connections need it. These events are: hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis, hci_le_cis_estabilished_evt. The Create CIS status/completion events shall queue new Create CIS only if at least one of the connections transitions away from BT_CONNECT, so that we don't loop if controller is sending bogus events. This fixes sending multiple CIS Create for the same CIS in the "ISO AC 6(i) - Success" BlueZ test case: < HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0] Number of CIS: 2 CIS Handle: 257 ACL Handle: 42 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #130 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 257 ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0] ... > HCI Event: Command Complete (0x0e) plen 6 #133 [hci0] LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 ... < HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0] Number of CIS: 1 CIS Handle: 258 ACL Handle: 42 > HCI Event: Command Status (0x0f) plen 4 #135 [hci0] LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: ACL Connection Already Exists (0x0b) > HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0] LE Connected Isochronous Stream Established (0x19) Status: Success (0x00) Connection Handle: 258 ... Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-06-01 09:34:46 +03:00
Bluetooth: Add initial implementation of CIS connections This adds the initial implementation of CIS connections and introduces the ISO packets/links. == Central: Set CIG Parameters, create a CIS and Setup Data Path == > tools/isotest -s <address> < HCI Command: LE Extended Create... (0x08|0x0043) plen 26 ... > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) ... < HCI Command: LE Create Connected... (0x08|0x0064) plen 5 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 == Peripheral: Accept CIS and Setup Data Path == > tools/isotest -d HCI Event: LE Meta Event (0x3e) plen 7 LE Connected Isochronous Stream Request (0x1a) ... < HCI Command: LE Accept Co.. (0x08|0x0066) plen 2 ... > HCI Event: LE Meta Event (0x3e) plen 29 LE Connected Isochronous Stream Established (0x19) ... < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 < HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 ... > HCI Event: Command Complete (0x0e) plen 6 LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1 Status: Success (0x00) Handle: 257 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2019-07-29 18:15:43 +03:00
Bluetooth: Add initial implementation of BIS connections This adds initial support for BIS/BIG which includes: == Broadcaster role: Setup a periodic advertising and create a BIG == > tools/isotest -s 00:00:00:00:00:00 isotest[63]: Connected [00:00:00:00:00:00] isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00] isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02 RTN 2] isotest[63]: Sending ... isotest[63]: Number of packets: 1 isotest[63]: Socket jitter buffer: 80 buffer < HCI Command: LE Set Perio.. (0x08|0x003e) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x003f) plen 7 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Perio.. (0x08|0x0040) plen 2 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1 Status: Success (0x00) < HCI Command: LE Create B.. (0x08|0x0068) plen 31 ... > HCI Event: Command Status (0x0f) plen 4 LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 21 LE Broadcast Isochronous Group Complete (0x1b) ... == Broadcast Receiver role: Create a PA Sync and BIG Sync == > tools/isotest -i hci1 -d 00:AA:01:00:00:00 isotest[66]: Waiting for connection 00:AA:01:00:00:00... < HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14 ... > HCI Event: Command Status (0x0f) plen 4 LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6 ... > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 29 LE Extended Advertising Report (0x0d) ... > HCI Event: LE Meta Event (0x3e) plen 16 LE Periodic Advertising Sync Established (0x0e) ... < HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25 ... > HCI Event: Command Status (0x0f) plen 4 LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 17 LE Broadcast Isochronous Group Sync Estabilished (0x1d) ... Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-03-09 13:22:20 -08:00
Bluetooth: hci_conn: Only do ACL connections sequentially Pretty much all bluetooth chipsets only support paging a single device at a time, and if they don't reject a secondary "Create Connection" request while another is still ongoing, they'll most likely serialize those requests in the firware. With commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect requests") we started adding some serialization of our own in case the adapter returns "Command Disallowed" HCI error. This commit was using the BT_CONNECT2 state for the serialization, this state is also used for a few more things (most notably to indicate we're waiting for an inquiry to cancel) and therefore a bit unreliable. Also not all BT firwares would respond with "Command Disallowed" on too many connection requests, some will also respond with "Hardware Failure" (BCM4378), and others will error out later and send a "Connect Complete" event with error "Rejected Limited Resources" (Marvell 88W8897). We can clean things up a bit and also make the serialization more reliable by using our hci_sync machinery to always do "Create Connection" requests in a sequential manner. This is very similar to what we're already doing for establishing LE connections, and it works well there. Note that this causes a test failure in mgmt-tester (test "Pair Device - Power off 1") because the hci_abort_conn_sync() changes the error we return on timeout of the "Create Connection". We'll fix this on the mgmt-tester side by adjusting the expected error for the test. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-02-06 12:08:13 +01:00
Bluetooth: hci_conn: Only do ACL connections sequentially Pretty much all bluetooth chipsets only support paging a single device at a time, and if they don't reject a secondary "Create Connection" request while another is still ongoing, they'll most likely serialize those requests in the firware. With commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect requests") we started adding some serialization of our own in case the adapter returns "Command Disallowed" HCI error. This commit was using the BT_CONNECT2 state for the serialization, this state is also used for a few more things (most notably to indicate we're waiting for an inquiry to cancel) and therefore a bit unreliable. Also not all BT firwares would respond with "Command Disallowed" on too many connection requests, some will also respond with "Hardware Failure" (BCM4378), and others will error out later and send a "Connect Complete" event with error "Rejected Limited Resources" (Marvell 88W8897). We can clean things up a bit and also make the serialization more reliable by using our hci_sync machinery to always do "Create Connection" requests in a sequential manner. This is very similar to what we're already doing for establishing LE connections, and it works well there. Note that this causes a test failure in mgmt-tester (test "Pair Device - Power off 1") because the hci_abort_conn_sync() changes the error we return on timeout of the "Create Connection". We'll fix this on the mgmt-tester side by adjusting the expected error for the test. Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-02-06 12:08:13 +01:00