kernel/linux
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-11-15 19:56:03 +00:00
Code Issues Releases Packages Activity
linux/drivers/tty/serial/sunplus-uart.c

767 lines
18 KiB
Raw Normal View History

serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
tty: serial: switch from circ_buf to kfifo Switch from struct circ_buf to proper kfifo. kfifo provides much better API, esp. when wrap-around of the buffer needs to be taken into account. Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example. Kfifo API can also fill in scatter-gather DMA structures, so it easier for that use case too. Look at lpuart_dma_tx() for example. Note that not all drivers can be converted to that (like atmel_serial), they handle DMA specially. Note that usb-serial uses kfifo for TX for ages. omap needed a bit more care as it needs to put a char into FIFO to start the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to do kfifo_dma_out_prepare twice: once to find out the tx_size (to find out if it is worths to do DMA at all -- size >= 4), the second time for the actual transfer. All traces of circ_buf are removed from serial_core.h (and its struct uart_state). Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Al Cooper <alcooperx@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com> Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hammer Hsieh <hammerh0314@gmail.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@kernel.org> Cc: Michal Simek <michal.simek@amd.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05 08:08:23 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
tty: serial: switch from circ_buf to kfifo Switch from struct circ_buf to proper kfifo. kfifo provides much better API, esp. when wrap-around of the buffer needs to be taken into account. Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example. Kfifo API can also fill in scatter-gather DMA structures, so it easier for that use case too. Look at lpuart_dma_tx() for example. Note that not all drivers can be converted to that (like atmel_serial), they handle DMA specially. Note that usb-serial uses kfifo for TX for ages. omap needed a bit more care as it needs to put a char into FIFO to start the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to do kfifo_dma_out_prepare twice: once to find out the tx_size (to find out if it is worths to do DMA at all -- size >= 4), the second time for the actual transfer. All traces of circ_buf are removed from serial_core.h (and its struct uart_state). Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Al Cooper <alcooperx@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com> Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hammer Hsieh <hammerh0314@gmail.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@kernel.org> Cc: Michal Simek <michal.simek@amd.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05 08:08:23 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
tty: serial: switch from circ_buf to kfifo Switch from struct circ_buf to proper kfifo. kfifo provides much better API, esp. when wrap-around of the buffer needs to be taken into account. Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example. Kfifo API can also fill in scatter-gather DMA structures, so it easier for that use case too. Look at lpuart_dma_tx() for example. Note that not all drivers can be converted to that (like atmel_serial), they handle DMA specially. Note that usb-serial uses kfifo for TX for ages. omap needed a bit more care as it needs to put a char into FIFO to start the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to do kfifo_dma_out_prepare twice: once to find out the tx_size (to find out if it is worths to do DMA at all -- size >= 4), the second time for the actual transfer. All traces of circ_buf are removed from serial_core.h (and its struct uart_state). Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Al Cooper <alcooperx@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com> Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hammer Hsieh <hammerh0314@gmail.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@kernel.org> Cc: Michal Simek <michal.simek@amd.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05 08:08:23 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
tty: serial: switch from circ_buf to kfifo Switch from struct circ_buf to proper kfifo. kfifo provides much better API, esp. when wrap-around of the buffer needs to be taken into account. Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example. Kfifo API can also fill in scatter-gather DMA structures, so it easier for that use case too. Look at lpuart_dma_tx() for example. Note that not all drivers can be converted to that (like atmel_serial), they handle DMA specially. Note that usb-serial uses kfifo for TX for ages. omap needed a bit more care as it needs to put a char into FIFO to start the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to do kfifo_dma_out_prepare twice: once to find out the tx_size (to find out if it is worths to do DMA at all -- size >= 4), the second time for the actual transfer. All traces of circ_buf are removed from serial_core.h (and its struct uart_state). Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Al Cooper <alcooperx@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com> Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hammer Hsieh <hammerh0314@gmail.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@kernel.org> Cc: Michal Simek <michal.simek@amd.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05 08:08:23 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
tty: serial: switch from circ_buf to kfifo Switch from struct circ_buf to proper kfifo. kfifo provides much better API, esp. when wrap-around of the buffer needs to be taken into account. Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example. Kfifo API can also fill in scatter-gather DMA structures, so it easier for that use case too. Look at lpuart_dma_tx() for example. Note that not all drivers can be converted to that (like atmel_serial), they handle DMA specially. Note that usb-serial uses kfifo for TX for ages. omap needed a bit more care as it needs to put a char into FIFO to start the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to do kfifo_dma_out_prepare twice: once to find out the tx_size (to find out if it is worths to do DMA at all -- size >= 4), the second time for the actual transfer. All traces of circ_buf are removed from serial_core.h (and its struct uart_state). Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Al Cooper <alcooperx@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com> Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hammer Hsieh <hammerh0314@gmail.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@kernel.org> Cc: Michal Simek <michal.simek@amd.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05 08:08:23 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
tty: serial: switch from circ_buf to kfifo Switch from struct circ_buf to proper kfifo. kfifo provides much better API, esp. when wrap-around of the buffer needs to be taken into account. Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example. Kfifo API can also fill in scatter-gather DMA structures, so it easier for that use case too. Look at lpuart_dma_tx() for example. Note that not all drivers can be converted to that (like atmel_serial), they handle DMA specially. Note that usb-serial uses kfifo for TX for ages. omap needed a bit more care as it needs to put a char into FIFO to start the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to do kfifo_dma_out_prepare twice: once to find out the tx_size (to find out if it is worths to do DMA at all -- size >= 4), the second time for the actual transfer. All traces of circ_buf are removed from serial_core.h (and its struct uart_state). Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Al Cooper <alcooperx@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com> Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hammer Hsieh <hammerh0314@gmail.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@kernel.org> Cc: Michal Simek <michal.simek@amd.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-05 08:08:23 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: drivers: switch ch and flag to u8 Now that the serial layer explicitly expects 'u8' for flags and characters, propagate this type to drivers' (RX) routines. Note that amba-pl011's, clps711x's and st-asc's 'ch' are left unchanged because 'ch' contains not only a character, but whole status. Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@orcam.me.uk> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Hammer Hsieh <hammerh0314@gmail.com> Acked-by: Richard GENOUD <richard.genoud@gmail.com> Acked-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/20230712081811.29004-11-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-12 10:18:11 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus: Use uart_prepare_sysrq_char(). The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT. The driver splits the locking function into two parts: local_irq_save() and uart_port_lock() and this breaks PREEMPT_RT. Delay handling sysrq until port lock is dropped. Remove the special case in the console write routine an always use the complete locking function. Cc: Hammer Hsieh <hammerh0314@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240301215246.891055-9-bigeasy@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-01 22:45:21 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus: Use uart_prepare_sysrq_char(). The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT. The driver splits the locking function into two parts: local_irq_save() and uart_port_lock() and this breaks PREEMPT_RT. Delay handling sysrq until port lock is dropped. Remove the special case in the console write routine an always use the complete locking function. Cc: Hammer Hsieh <hammerh0314@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240301215246.891055-9-bigeasy@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-01 22:45:21 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: Make ->set_termios() old ktermios const There should be no reason to adjust old ktermios which is going to get discarded anyway. Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-08-16 14:57:37 +03:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Use port lock wrappers When a serial port is used for kernel console output, then all modifications to the UART registers which are done from other contexts, e.g. getty, termios, are interference points for the kernel console. So far this has been ignored and the printk output is based on the principle of hope. The rework of the console infrastructure which aims to support threaded and atomic consoles, requires to mark sections which modify the UART registers as unsafe. This allows the atomic write function to make informed decisions and eventually to restore operational state. It also allows to prevent the regular UART code from modifying UART registers while printk output is in progress. All modifications of UART registers are guarded by the UART port lock, which provides an obvious synchronization point with the console infrastructure. To avoid adding this functionality to all UART drivers, wrap the spin_[un]lock*() invocations for uart_port::lock into helper functions which just contain the spin_[un]lock*() invocations for now. In a subsequent step these helpers will gain the console synchronization mechanisms. Converted with coccinelle. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20230914183831.587273-67-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-09-14 20:44:23 +02:06
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Fix compile error while CONFIG_SERIAL_SUNPLUS_CONSOLE=n 1. Fix implicit declaration of function 'wait_for_xmitr' issue. 2. Fix 'sunplus_uart_console' undeclared here issue. 3. Fix use of undeclared identifier 'sunplus_uart_console' issue. Fixes: 9e8d5470325f ("serial: sunplus-uart: Add Sunplus SoC UART Driver") Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1646108386-29905-1-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-01 12:19:46 +08:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: change sunplus_console_ports from global to static Smatch reports this issue sunplus-uart.c:501:26: warning: symbol 'sunplus_console_ports' was not declared. Should it be static? sunplus_console_ports is only used in sunplus-uart.c so change its storage-class specifier to static Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/20220421152505.1531507-1-trix@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-21 11:25:05 -04:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: make uart_console_write->putchar()'s character an unsigned char Currently, uart_console_write->putchar's second parameter (the character) is of type int. It makes little sense, provided uart_console_write() accepts the input string as "const char *s" and passes its content -- the characters -- to putchar(). So switch the character's type to unsigned char. We don't use char as that is signed on some platforms. That would cause troubles for drivers which (implicitly) cast the char to u16 when writing to the device. Sign extension would happen in that case and the value written would be completely different to the provided char. DZ is an example of such a driver -- on MIPS, it uses u16 for dz_out in dz_console_putchar(). Note we do the char -> uchar conversion implicitly in uart_console_write(). Provided we do not change size of the data type, sign extension does not happen there, so the problem is void. This makes the types consistent and unified with the rest of the uart layer, which uses unsigned char in most places already. One exception is xmit_buf, but that is going to be converted later. Cc: Paul Cercueil <paul@crapouillou.net> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@orcam.me.uk> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Karol Gugala <kgugala@antmicro.com> Cc: Mateusz Holenko <mholenko@antmicro.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang7@gmail.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <peter@korsgaard.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial] Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03 09:08:31 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus: Use uart_prepare_sysrq_char(). The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT. The driver splits the locking function into two parts: local_irq_save() and uart_port_lock() and this breaks PREEMPT_RT. Delay handling sysrq until port lock is dropped. Remove the special case in the console write routine an always use the complete locking function. Cc: Hammer Hsieh <hammerh0314@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240301215246.891055-9-bigeasy@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-01 22:45:21 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus: Use uart_prepare_sysrq_char(). The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT. The driver splits the locking function into two parts: local_irq_save() and uart_port_lock() and this breaks PREEMPT_RT. Delay handling sysrq until port lock is dropped. Remove the special case in the console write routine an always use the complete locking function. Cc: Hammer Hsieh <hammerh0314@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240301215246.891055-9-bigeasy@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-01 22:45:21 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus: Use uart_prepare_sysrq_char(). The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT. The driver splits the locking function into two parts: local_irq_save() and uart_port_lock() and this breaks PREEMPT_RT. Delay handling sysrq until port lock is dropped. Remove the special case in the console write routine an always use the complete locking function. Cc: Hammer Hsieh <hammerh0314@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240301215246.891055-9-bigeasy@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-01 22:45:21 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Fix compile error while CONFIG_SERIAL_SUNPLUS_CONSOLE=n 1. Fix implicit declaration of function 'wait_for_xmitr' issue. 2. Fix 'sunplus_uart_console' undeclared here issue. 3. Fix use of undeclared identifier 'sunplus_uart_console' issue. Fixes: 9e8d5470325f ("serial: sunplus-uart: Add Sunplus SoC UART Driver") Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1646108386-29905-1-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-01 12:19:46 +08:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus-uart: Fix compile error while CONFIG_SERIAL_SUNPLUS_CONSOLE=n 1. Fix implicit declaration of function 'wait_for_xmitr' issue. 2. Fix 'sunplus_uart_console' undeclared here issue. 3. Fix use of undeclared identifier 'sunplus_uart_console' issue. Fixes: 9e8d5470325f ("serial: sunplus-uart: Add Sunplus SoC UART Driver") Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1646108386-29905-1-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-01 12:19:46 +08:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: sunplus: Convert to platform remove callback returning void The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231110152927.70601-45-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-11-10 16:30:12 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: Switch back to struct platform_driver::remove() After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all platform drivers below drivers/tty/serial to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Link: https://lore.kernel.org/r/20241007205803.444994-7-u.kleine-koenig@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-10-07 22:58:04 +02:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00
serial: make uart_console_write->putchar()'s character an unsigned char Currently, uart_console_write->putchar's second parameter (the character) is of type int. It makes little sense, provided uart_console_write() accepts the input string as "const char *s" and passes its content -- the characters -- to putchar(). So switch the character's type to unsigned char. We don't use char as that is signed on some platforms. That would cause troubles for drivers which (implicitly) cast the char to u16 when writing to the device. Sign extension would happen in that case and the value written would be completely different to the provided char. DZ is an example of such a driver -- on MIPS, it uses u16 for dz_out in dz_console_putchar(). Note we do the char -> uchar conversion implicitly in uart_console_write(). Provided we do not change size of the data type, sign extension does not happen there, so the problem is void. This makes the types consistent and unified with the rest of the uart layer, which uses unsigned char in most places already. One exception is xmit_buf, but that is going to be converted later. Cc: Paul Cercueil <paul@crapouillou.net> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@kernel.org> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@orcam.me.uk> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Karol Gugala <kgugala@antmicro.com> Cc: Mateusz Holenko <mholenko@antmicro.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Taichi Sugaya <sugaya.taichi@socionext.com> Cc: Takao Orito <orito.takao@socionext.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Cc: Orson Zhai <orsonzhai@gmail.com> Cc: Baolin Wang <baolin.wang7@gmail.com> Cc: Chunyan Zhang <zhang.lyra@gmail.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <peter@korsgaard.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial] Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03 09:08:31 +01:00
serial: sunplus-uart: Add Sunplus SoC UART Driver Add Sunplus SoC UART Driver. SP7021 UART block contains 5 UARTs. There are UART0~4 that supported in SP7021, the features list as below. Support Full-duplex communication. Support data packet length configurable. Support stop bit number configurable. Support force break condition. Support baud rate configurable. Support error detection and report. Support RXD Noise Rejection Vote configurable. UART0 pinout only support TX/RX two pins. UART1 to UART4 pinout support TX/RX/CTS/RTS four pins. Normally UART0 used for kernel console, also can be used for normal uart. Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port. UART driver probe will create path named "/dev/ttySUPx". https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com> Link: https://lore.kernel.org/r/1645522563-17183-3-git-send-email-hammerh0314@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-22 17:36:03 +08:00