kernel/linux
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-11-13 07:31:07 +00:00
Code Issues Releases Packages Activity
linux/drivers/input/misc/rb532_button.c

108 lines
2.6 KiB
Raw Normal View History

treewide: Add SPDX license identifier for more missed files Add SPDX license identifiers to all files which: - Have no license information of any form - Have MODULE_LICENCE("GPL*") inside which was used in the initial scan/conversion to ignore the file These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-19 13:08:20 +01:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
MIPS: Remove all the uses of custom gpio.h Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS machines, and each machine type provides its own gpio.h. However only a handful really implement the GPIO API, most just forward everythings to gpiolib. The Alchemy machine is notable as it provides a system to allow implementing the GPIO API at the board level. But it is not used by any board currently supported, so it can also be removed. For most machine types we can just remove the custom gpio.h, as well as the custom wrappers if some exists. Some of the code found in the wrappers must be moved to the respective GPIO driver. A few more fixes are need in some drivers as they rely on linux/gpio.h to provides some machine specific definitions, or used asm/gpio.h instead of linux/gpio.h for the gpio API. Signed-off-by: Alban Bedel <albeu@free.fr> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: linux-mips@linux-mips.org Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: Tejun Heo <tj@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Florian Fainelli <florian@openwrt.org> Cc: Manuel Lauss <manuel.lauss@gmail.com> Cc: Joe Perches <joe@perches.com> Cc: Daniel Walter <dwalter@google.com> Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: James Hartley <james.hartley@imgtec.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Varka Bhadram <varkabhadram@gmail.com> Cc: Masanari Iida <standby24x7@gmail.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Michael Buesch <m@bues.ch> Cc: abdoulaye berthe <berthe.ab@gmail.com> Cc: linux-kernel@vger.kernel.org Cc: linux-ide@vger.kernel.org Cc: linux-gpio@vger.kernel.org Cc: linux-input@vger.kernel.org Cc: netdev@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/10828/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-08-02 18:30:11 +02:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: remove use of __devinit CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-23 21:38:25 -08:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: remove use of __devexit CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-23 21:50:47 -08:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: remove use of __devexit_p CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-23 21:27:39 -08:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00
Input: misc - use macro module_platform_driver() Commit 940ab88962bc1aff3273a8356d64577a6e386736 introduced a new macro to save some platform_driver boilerplate code. Use it. Signed-off-by: JJ Ding <dgdunix@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2011-11-29 11:08:40 -08:00
Input: add driver for S1 button of rb532 Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-04 23:27:15 -08:00