linux/drivers/scsi/scsi_error.c

2219 lines
60 KiB

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 17:04:11 +09:00
[SCSI] add queue_depth ramp up code Current FC HBA queue_depth ramp up code depends on last queue full time. The sdev already has last_queue_full_time field to track last queue full time but stored value is truncated by last four bits. So this patch updates last_queue_full_time without truncating last 4 bits to store full value and then updates its only current usages in scsi_track_queue_full to ignore last four bits to keep current usages same while also use this field in added ramp up code. Adds scsi_handle_queue_ramp_up to ramp up queue_depth on successful completion of IO. The scsi_handle_queue_ramp_up will do ramp up on all luns of a target, just same as ramp down done on all luns on a target. The ramp up is skipped in case the change_queue_depth is not supported by LLD or already reached to added max_queue_depth. Updates added max_queue_depth on every new update to default queue_depth value. The ramp up is also skipped if lapsed time since either last queue ramp up or down is less than LLD specified queue_ramp_up_period. Adds queue_ramp_up_period to sysfs but only if change_queue_depth is supported since ramp up and queue_ramp_up_period is needed only in case change_queue_depth is supported first. Initializes queue_ramp_up_period to 120HZ jiffies as initial default value, it is same as used in existing lpfc and qla2xxx. -v2 Combined all ramp code into this single patch. -v3 Moves max_queue_depth initialization after slave_configure is called from after slave_alloc calling done. Also adjusted max_queue_depth check to skip ramp up if current queue_depth is >= max_queue_depth. -v4 Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f to store or show its value. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com> Tested-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-10-22 15:46:33 -07:00
[SCSI] add queue_depth ramp up code Current FC HBA queue_depth ramp up code depends on last queue full time. The sdev already has last_queue_full_time field to track last queue full time but stored value is truncated by last four bits. So this patch updates last_queue_full_time without truncating last 4 bits to store full value and then updates its only current usages in scsi_track_queue_full to ignore last four bits to keep current usages same while also use this field in added ramp up code. Adds scsi_handle_queue_ramp_up to ramp up queue_depth on successful completion of IO. The scsi_handle_queue_ramp_up will do ramp up on all luns of a target, just same as ramp down done on all luns on a target. The ramp up is skipped in case the change_queue_depth is not supported by LLD or already reached to added max_queue_depth. Updates added max_queue_depth on every new update to default queue_depth value. The ramp up is also skipped if lapsed time since either last queue ramp up or down is less than LLD specified queue_ramp_up_period. Adds queue_ramp_up_period to sysfs but only if change_queue_depth is supported since ramp up and queue_ramp_up_period is needed only in case change_queue_depth is supported first. Initializes queue_ramp_up_period to 120HZ jiffies as initial default value, it is same as used in existing lpfc and qla2xxx. -v2 Combined all ramp code into this single patch. -v3 Moves max_queue_depth initialization after slave_configure is called from after slave_alloc calling done. Also adjusted max_queue_depth check to skip ramp up if current queue_depth is >= max_queue_depth. -v4 Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f to store or show its value. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com> Tested-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-10-22 15:46:33 -07:00
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer - struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-30 11:19:47 +03:00
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer - struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-30 11:19:47 +03:00
[SCSI] bidirectional command support At the block level bidi request uses req->next_rq pointer for a second bidi_read request. At Scsi-midlayer a second scsi_data_buffer structure is used for the bidi_read part. This bidi scsi_data_buffer is put on request->next_rq->special. Struct scsi_cmnd is not changed. - Define scsi_bidi_cmnd() to return true if it is a bidi request and a second sgtable was allocated. - Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer from this command This API is to isolate users from the mechanics of bidi. - Define scsi_end_bidi_request() to do what scsi_end_request() does but for a bidi request. This is necessary because bidi commands are a bit tricky here. (See comments in body) - scsi_release_buffers() will also release the bidi_read scsi_data_buffer - scsi_io_completion() on bidi commands will now call scsi_end_bidi_request() and return. - The previous work done in scsi_init_io() is now done in a new scsi_init_sgtable() (which is 99% identical to old scsi_init_io()) The new scsi_init_io() will call the above twice if needed also for the bidi_read command. Only at this point is a command bidi. - In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not confused by a get-sense command that looks like bidi. This is done by puting NULL at request->next_rq, and restoring. [jejb: update to sg_table and resolve conflicts also update to blk-end-request and resolve conflicts] Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2007-12-13 13:50:53 +02:00
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer - struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-30 11:19:47 +03:00
[SCSI] bidirectional command support At the block level bidi request uses req->next_rq pointer for a second bidi_read request. At Scsi-midlayer a second scsi_data_buffer structure is used for the bidi_read part. This bidi scsi_data_buffer is put on request->next_rq->special. Struct scsi_cmnd is not changed. - Define scsi_bidi_cmnd() to return true if it is a bidi request and a second sgtable was allocated. - Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer from this command This API is to isolate users from the mechanics of bidi. - Define scsi_end_bidi_request() to do what scsi_end_request() does but for a bidi request. This is necessary because bidi commands are a bit tricky here. (See comments in body) - scsi_release_buffers() will also release the bidi_read scsi_data_buffer - scsi_io_completion() on bidi commands will now call scsi_end_bidi_request() and return. - The previous work done in scsi_init_io() is now done in a new scsi_init_sgtable() (which is 99% identical to old scsi_init_io()) The new scsi_init_io() will call the above twice if needed also for the bidi_read command. Only at this point is a command bidi. - In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not confused by a get-sense command that looks like bidi. This is done by puting NULL at request->next_rq, and restoring. [jejb: update to sg_table and resolve conflicts also update to blk-end-request and resolve conflicts] Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2007-12-13 13:50:53 +02:00
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer - struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-30 11:19:47 +03:00
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer - struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-30 11:19:47 +03:00
[SCSI] bidirectional command support At the block level bidi request uses req->next_rq pointer for a second bidi_read request. At Scsi-midlayer a second scsi_data_buffer structure is used for the bidi_read part. This bidi scsi_data_buffer is put on request->next_rq->special. Struct scsi_cmnd is not changed. - Define scsi_bidi_cmnd() to return true if it is a bidi request and a second sgtable was allocated. - Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer from this command This API is to isolate users from the mechanics of bidi. - Define scsi_end_bidi_request() to do what scsi_end_request() does but for a bidi request. This is necessary because bidi commands are a bit tricky here. (See comments in body) - scsi_release_buffers() will also release the bidi_read scsi_data_buffer - scsi_io_completion() on bidi commands will now call scsi_end_bidi_request() and return. - The previous work done in scsi_init_io() is now done in a new scsi_init_sgtable() (which is 99% identical to old scsi_init_io()) The new scsi_init_io() will call the above twice if needed also for the bidi_read command. Only at this point is a command bidi. - In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not confused by a get-sense command that looks like bidi. This is done by puting NULL at request->next_rq, and restoring. [jejb: update to sg_table and resolve conflicts also update to blk-end-request and resolve conflicts] Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2007-12-13 13:50:53 +02:00
[SCSI] scsi: add transport host byte errors (v3) Currently, if there is a transport problem the iscsi drivers will return outstanding commands (commands being exeucted by the driver/fw/hw) with DID_BUS_BUSY and block the session so no new commands can be queued. Commands that are caught between the failure handling and blocking are failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values. When the recovery_timeout fires, the iscsi drivers then fail IO with DID_NO_CONNECT. For fcp, some drivers will fail some outstanding IO (disk but possibly not tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry and hits the scsi_error.c failfast check, block the rport, and commands caught in the race are failed with DID_IMM_RETRY. Other drivers, may hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk to be called. The following patches attempt to unify what upper layers will see drivers like multipath can make a good guess. This relies on drivers being hooked into their transport class. This first patch just defines two new host byte errors so drivers can return the same value for when a rport/session is blocked and for when the fast_io_fail_tmo fires. The idea is that if the LLD/class detects a problem and is going to block a rport/session, then if the LLD wants or must return the command to scsi-ml, then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue the IO into the same scsi queue it came from, until the fast io fail timer fires and the class decides what to do. When using multipath and the fast_io_fail_tmo fires then the class can fail commands with DID_TRANSPORT_FAILFAST or drivers can use DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or the equivlent in iscsi if we ever implement more advanced recovery methods. A LLD, like lpfc, could continue to return DID_ERROR and then it will hit the normal failfast path, so drivers do not have fully be ported to work better. The point of the patches is that upper layers will not see a failure that could be recovered from while the rport/session is blocked until fast_io_fail_tmo/recovery_timeout fires. V3 Remove some comments. V2 Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to DID_TRANSPORT_DISRUPTED. V1 initial patch. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-08-19 18:45:25 -05:00
[SCSI] scsi: add transport host byte errors (v3) Currently, if there is a transport problem the iscsi drivers will return outstanding commands (commands being exeucted by the driver/fw/hw) with DID_BUS_BUSY and block the session so no new commands can be queued. Commands that are caught between the failure handling and blocking are failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values. When the recovery_timeout fires, the iscsi drivers then fail IO with DID_NO_CONNECT. For fcp, some drivers will fail some outstanding IO (disk but possibly not tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry and hits the scsi_error.c failfast check, block the rport, and commands caught in the race are failed with DID_IMM_RETRY. Other drivers, may hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk to be called. The following patches attempt to unify what upper layers will see drivers like multipath can make a good guess. This relies on drivers being hooked into their transport class. This first patch just defines two new host byte errors so drivers can return the same value for when a rport/session is blocked and for when the fast_io_fail_tmo fires. The idea is that if the LLD/class detects a problem and is going to block a rport/session, then if the LLD wants or must return the command to scsi-ml, then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue the IO into the same scsi queue it came from, until the fast io fail timer fires and the class decides what to do. When using multipath and the fast_io_fail_tmo fires then the class can fail commands with DID_TRANSPORT_FAILFAST or drivers can use DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or the equivlent in iscsi if we ever implement more advanced recovery methods. A LLD, like lpfc, could continue to return DID_ERROR and then it will hit the normal failfast path, so drivers do not have fully be ported to work better. The point of the patches is that upper layers will not see a failure that could be recovered from while the rport/session is blocked until fast_io_fail_tmo/recovery_timeout fires. V3 Remove some comments. V2 Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to DID_TRANSPORT_DISRUPTED. V1 initial patch. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-08-19 18:45:25 -05:00
[SCSI] scsi: add transport host byte errors (v3) Currently, if there is a transport problem the iscsi drivers will return outstanding commands (commands being exeucted by the driver/fw/hw) with DID_BUS_BUSY and block the session so no new commands can be queued. Commands that are caught between the failure handling and blocking are failed with DID_IMM_RETRY or one of the scsi ml queuecommand return values. When the recovery_timeout fires, the iscsi drivers then fail IO with DID_NO_CONNECT. For fcp, some drivers will fail some outstanding IO (disk but possibly not tape) with DID_BUS_BUSY or DID_ERROR or some other value that causes a retry and hits the scsi_error.c failfast check, block the rport, and commands caught in the race are failed with DID_IMM_RETRY. Other drivers, may hold onto all IO and wait for the terminate_rport_io or dev_loss_tmo_callbk to be called. The following patches attempt to unify what upper layers will see drivers like multipath can make a good guess. This relies on drivers being hooked into their transport class. This first patch just defines two new host byte errors so drivers can return the same value for when a rport/session is blocked and for when the fast_io_fail_tmo fires. The idea is that if the LLD/class detects a problem and is going to block a rport/session, then if the LLD wants or must return the command to scsi-ml, then it can return it with DID_TRANSPORT_DISRUPTED. This will requeue the IO into the same scsi queue it came from, until the fast io fail timer fires and the class decides what to do. When using multipath and the fast_io_fail_tmo fires then the class can fail commands with DID_TRANSPORT_FAILFAST or drivers can use DID_TRANSPORT_FAILFAST in their terminate_rport_io callbacks or the equivlent in iscsi if we ever implement more advanced recovery methods. A LLD, like lpfc, could continue to return DID_ERROR and then it will hit the normal failfast path, so drivers do not have fully be ported to work better. The point of the patches is that upper layers will not see a failure that could be recovered from while the rport/session is blocked until fast_io_fail_tmo/recovery_timeout fires. V3 Remove some comments. V2 Fixed patch/diff errors and renamed DID_TRANSPORT_BLOCKED to DID_TRANSPORT_DISRUPTED. V1 initial patch. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-08-19 18:45:25 -05:00
[SCSI] add queue_depth ramp up code Current FC HBA queue_depth ramp up code depends on last queue full time. The sdev already has last_queue_full_time field to track last queue full time but stored value is truncated by last four bits. So this patch updates last_queue_full_time without truncating last 4 bits to store full value and then updates its only current usages in scsi_track_queue_full to ignore last four bits to keep current usages same while also use this field in added ramp up code. Adds scsi_handle_queue_ramp_up to ramp up queue_depth on successful completion of IO. The scsi_handle_queue_ramp_up will do ramp up on all luns of a target, just same as ramp down done on all luns on a target. The ramp up is skipped in case the change_queue_depth is not supported by LLD or already reached to added max_queue_depth. Updates added max_queue_depth on every new update to default queue_depth value. The ramp up is also skipped if lapsed time since either last queue ramp up or down is less than LLD specified queue_ramp_up_period. Adds queue_ramp_up_period to sysfs but only if change_queue_depth is supported since ramp up and queue_ramp_up_period is needed only in case change_queue_depth is supported first. Initializes queue_ramp_up_period to 120HZ jiffies as initial default value, it is same as used in existing lpfc and qla2xxx. -v2 Combined all ramp code into this single patch. -v3 Moves max_queue_depth initialization after slave_configure is called from after slave_alloc calling done. Also adjusted max_queue_depth check to skip ramp up if current queue_depth is >= max_queue_depth. -v4 Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f to store or show its value. Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com> Tested-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-10-22 15:46:33 -07:00
[SCSI] implement runtime Power Management This patch (as1398b) adds runtime PM support to the SCSI layer. Only the machanism is provided; use of it is up to the various high-level drivers, and the patch doesn't change any of them. Except for sg -- the patch expicitly prevents a device from being runtime-suspended while its sg device file is open. The implementation is simplistic. In general, hosts and targets are automatically suspended when all their children are asleep, but for them the runtime-suspend code doesn't actually do anything. (A host's runtime PM status is propagated up the device tree, though, so a runtime-PM-aware lower-level driver could power down the host adapter hardware at the appropriate times.) There are comments indicating where a transport class might be notified or some other hooks added. LUNs are runtime-suspended by calling the drivers' existing suspend handlers (and likewise for runtime-resume). Somewhat arbitrarily, the implementation delays for 100 ms before suspending an eligible LUN. This is because there typically are occasions during bootup when the same device file is opened and closed several times in quick succession. The way this all works is that the SCSI core increments a device's PM-usage count when it is registered. If a high-level driver does nothing then the device will not be eligible for runtime-suspend because of the elevated usage count. If a high-level driver wants to use runtime PM then it can call scsi_autopm_put_device() in its probe routine to decrement the usage count and scsi_autopm_get_device() in its remove routine to restore the original count. Hosts, targets, and LUNs are not suspended while they are being probed or removed, or while the error handler is running. In fact, a fairly large part of the patch consists of code to make sure that things aren't suspended at such times. [jejb: fix up compile issues in PM config variations] Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-06-17 10:41:42 -04:00
[SCSI] implement runtime Power Management This patch (as1398b) adds runtime PM support to the SCSI layer. Only the machanism is provided; use of it is up to the various high-level drivers, and the patch doesn't change any of them. Except for sg -- the patch expicitly prevents a device from being runtime-suspended while its sg device file is open. The implementation is simplistic. In general, hosts and targets are automatically suspended when all their children are asleep, but for them the runtime-suspend code doesn't actually do anything. (A host's runtime PM status is propagated up the device tree, though, so a runtime-PM-aware lower-level driver could power down the host adapter hardware at the appropriate times.) There are comments indicating where a transport class might be notified or some other hooks added. LUNs are runtime-suspended by calling the drivers' existing suspend handlers (and likewise for runtime-resume). Somewhat arbitrarily, the implementation delays for 100 ms before suspending an eligible LUN. This is because there typically are occasions during bootup when the same device file is opened and closed several times in quick succession. The way this all works is that the SCSI core increments a device's PM-usage count when it is registered. If a high-level driver does nothing then the device will not be eligible for runtime-suspend because of the elevated usage count. If a high-level driver wants to use runtime PM then it can call scsi_autopm_put_device() in its probe routine to decrement the usage count and scsi_autopm_get_device() in its remove routine to restore the original count. Hosts, targets, and LUNs are not suspended while they are being probed or removed, or while the error handler is running. In fact, a fairly large part of the patch consists of code to make sure that things aren't suspended at such times. [jejb: fix up compile issues in PM config variations] Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-06-17 10:41:42 -04:00
[SCSI] implement runtime Power Management This patch (as1398b) adds runtime PM support to the SCSI layer. Only the machanism is provided; use of it is up to the various high-level drivers, and the patch doesn't change any of them. Except for sg -- the patch expicitly prevents a device from being runtime-suspended while its sg device file is open. The implementation is simplistic. In general, hosts and targets are automatically suspended when all their children are asleep, but for them the runtime-suspend code doesn't actually do anything. (A host's runtime PM status is propagated up the device tree, though, so a runtime-PM-aware lower-level driver could power down the host adapter hardware at the appropriate times.) There are comments indicating where a transport class might be notified or some other hooks added. LUNs are runtime-suspended by calling the drivers' existing suspend handlers (and likewise for runtime-resume). Somewhat arbitrarily, the implementation delays for 100 ms before suspending an eligible LUN. This is because there typically are occasions during bootup when the same device file is opened and closed several times in quick succession. The way this all works is that the SCSI core increments a device's PM-usage count when it is registered. If a high-level driver does nothing then the device will not be eligible for runtime-suspend because of the elevated usage count. If a high-level driver wants to use runtime PM then it can call scsi_autopm_put_device() in its probe routine to decrement the usage count and scsi_autopm_get_device() in its remove routine to restore the original count. Hosts, targets, and LUNs are not suspended while they are being probed or removed, or while the error handler is running. In fact, a fairly large part of the patch consists of code to make sure that things aren't suspended at such times. [jejb: fix up compile issues in PM config variations] Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-06-17 10:41:42 -04:00
[SCSI] Let scsi_cmnd->cmnd use request->cmd buffer - struct scsi_cmnd had a 16 bytes command buffer of its own. This is an unnecessary duplication and copy of request's cmd. It is probably left overs from the time that scsi_cmnd could function without a request attached. So clean that up. - Once above is done, few places, apart from scsi-ml, needed adjustments due to changing the data type of scsi_cmnd->cmnd. - Lots of drivers still use MAX_COMMAND_SIZE. So I have left that #define but equate it to BLK_MAX_CDB. The way I see it and is reflected in the patch below is. MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB as per the SCSI standard and is not related to the implementation. BLK_MAX_CDB. - The allocated space at the request level - I have audit all ISA drivers and made sure none use ->cmnd in a DMA Operation. Same audit was done by Andi Kleen. (*)fixed-length here means commands that their size can be determined by their opcode and the CDB does not carry a length specifier, (unlike the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly true and the SCSI standard also defines extended commands and vendor specific commands that can be bigger than 16 bytes. The kernel will support these using the same infrastructure used for VARLEN CDB's. So in effect MAX_COMMAND_SIZE means the maximum size command scsi-ml supports without specifying a cmd_len by ULD's Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-30 11:19:47 +03:00
[SCSI] implement runtime Power Management This patch (as1398b) adds runtime PM support to the SCSI layer. Only the machanism is provided; use of it is up to the various high-level drivers, and the patch doesn't change any of them. Except for sg -- the patch expicitly prevents a device from being runtime-suspended while its sg device file is open. The implementation is simplistic. In general, hosts and targets are automatically suspended when all their children are asleep, but for them the runtime-suspend code doesn't actually do anything. (A host's runtime PM status is propagated up the device tree, though, so a runtime-PM-aware lower-level driver could power down the host adapter hardware at the appropriate times.) There are comments indicating where a transport class might be notified or some other hooks added. LUNs are runtime-suspended by calling the drivers' existing suspend handlers (and likewise for runtime-resume). Somewhat arbitrarily, the implementation delays for 100 ms before suspending an eligible LUN. This is because there typically are occasions during bootup when the same device file is opened and closed several times in quick succession. The way this all works is that the SCSI core increments a device's PM-usage count when it is registered. If a high-level driver does nothing then the device will not be eligible for runtime-suspend because of the elevated usage count. If a high-level driver wants to use runtime PM then it can call scsi_autopm_put_device() in its probe routine to decrement the usage count and scsi_autopm_get_device() in its remove routine to restore the original count. Hosts, targets, and LUNs are not suspended while they are being probed or removed, or while the error handler is running. In fact, a fairly large part of the patch consists of code to make sure that things aren't suspended at such times. [jejb: fix up compile issues in PM config variations] Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-06-17 10:41:42 -04:00