2018-01-26 12:50:27 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-08-24 16:43:55 +02:00
|
|
|
|
2020-11-29 23:07:39 +00:00
|
|
|
|
2016-11-11 16:08:45 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:28:00 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-09-16 07:54:35 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-05-27 23:02:40 -04:00
|
|
|
|
2018-05-18 13:28:00 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-05-27 23:02:40 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-08-23 16:36:42 -05:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-08-23 16:36:42 -05:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-11-11 16:08:45 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2022-02-13 14:54:05 +01:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-11-11 16:08:45 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2022-02-13 14:54:05 +01:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-29 23:07:42 +00:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-09-16 07:54:34 -06:00
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-09-02 11:53:05 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-09-02 11:53:05 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2020-10-24 22:35:15 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
2016-08-23 16:36:42 -05:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-08-23 16:36:42 -05:00
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
2016-08-23 16:36:42 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:53 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:53 -06:00
|
|
|
|
2018-05-08 10:00:22 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
2018-05-08 10:00:22 -06:00
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:53 -06:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:53 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2022-02-13 14:54:05 +01:00
|
|
|
|
2016-09-02 11:53:04 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-11-11 16:08:45 -07:00
|
|
|
|
2016-08-04 16:09:09 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-06-20 09:39:51 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2016-11-11 16:08:45 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-07-23 15:27:12 +02:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:42 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
pci-v5.10-changes
-----BEGIN PGP SIGNATURE-----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=RCFo
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
2020-10-22 12:41:00 -07:00
|
|
|
|
2020-07-28 13:49:42 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:42 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-29 23:07:42 +00:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2020-11-29 23:07:39 +00:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2020-11-29 23:07:39 +00:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2020-11-29 23:07:39 +00:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-29 23:07:42 +00:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-29 23:07:42 +00:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-08-24 16:43:55 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-16 15:11:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-10-03 15:52:58 +03:00
|
|
|
|
2021-11-16 15:11:36 -07:00
|
|
|
|
2023-10-03 15:53:00 +03:00
|
|
|
|
2021-11-16 15:11:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-08-10 17:50:29 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-16 15:11:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-02-24 10:06:37 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2017-06-19 15:26:57 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:40 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-18 19:33:27 +05:30
|
|
|
|
2020-07-28 13:49:40 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:41 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:43 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:43 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-02-13 14:54:05 +01:00
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:43 -06:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
2020-07-28 13:49:43 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-12-03 11:15:41 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-10-01 16:34:38 +08:00
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-10-01 16:34:38 +08:00
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-10-01 16:34:38 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
2019-09-16 07:54:34 -06:00
|
|
|
|
2018-12-13 09:23:42 -07:00
|
|
|
|
2022-12-05 17:16:37 -07:00
|
|
|
|
2020-07-28 13:49:40 -06:00
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-09-16 07:54:35 -06:00
|
|
|
|
2020-07-28 13:49:40 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-05-27 23:02:40 -04:00
|
|
|
|
|
|
|
|
|
2018-05-18 13:28:00 -06:00
|
|
|
|
|
|
|
|
|
2019-11-12 05:47:52 -07:00
|
|
|
|
2018-05-18 13:28:00 -06:00
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:41 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:28:00 -06:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-09-16 07:54:34 -06:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-03-02 15:31:03 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-05-30 08:05:58 -05:00
|
|
|
|
2016-03-02 15:31:03 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-02-24 10:06:37 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2016-02-24 10:06:37 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2020-01-21 06:37:46 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-08-26 13:16:52 +02:00
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-08-26 13:16:52 +02:00
|
|
|
|
2022-05-11 02:57:07 -07:00
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-08-26 13:16:52 +02:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2018-05-18 13:27:59 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2019-09-16 07:54:34 -06:00
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2020-07-28 13:49:42 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-12-03 11:15:41 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2016-02-24 10:06:37 -07:00
|
|
|
|
2020-07-28 13:49:42 -06:00
|
|
|
|
|
|
|
|
|
2022-05-11 02:57:06 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-12-13 09:23:42 -07:00
|
|
|
|
2024-06-05 20:48:44 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-08-24 16:43:55 +02:00
|
|
|
|
|
|
|
|
|
2018-12-13 09:23:42 -07:00
|
|
|
|
2021-11-16 15:11:36 -07:00
|
|
|
|
2022-12-05 17:16:37 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-04-20 17:43:31 +08:00
|
|
|
|
|
|
|
|
|
2022-12-05 17:16:37 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2018-12-13 09:23:42 -07:00
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:22 -08:00
|
|
|
|
|
|
|
|
|
2018-12-13 09:23:42 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2021-08-24 16:43:55 +02:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2020-07-28 13:49:43 -06:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-12-10 18:50:03 +01:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-05-31 18:56:17 +05:30
|
|
|
|
|
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2020-11-02 15:22:23 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
|
|
|
|
|
2023-12-10 18:50:03 +01:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2016-11-11 16:08:45 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-06-05 20:48:44 +08:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
2017-06-22 09:15:42 -06:00
|
|
|
|
2018-10-15 18:48:07 -06:00
|
|
|
|
2020-07-28 13:49:42 -06:00
|
|
|
|
2023-12-10 18:50:03 +01:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
2023-02-24 13:28:11 -07:00
|
|
|
|
|
|
|
|
|
2024-09-01 14:56:02 +05:30
|
|
|
|
2023-02-24 13:28:11 -07:00
|
|
|
|
2024-09-01 14:56:02 +05:30
|
|
|
|
2023-02-24 13:28:11 -07:00
|
|
|
|
|
|
|
|
|
2016-11-26 19:29:57 +01:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2017-08-11 14:54:32 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-02-13 14:54:05 +01:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2017-08-11 14:54:32 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-06-27 19:38:08 +08:00
|
|
|
|
2022-11-09 07:26:52 -07:00
|
|
|
|
2017-08-11 14:54:32 -06:00
|
|
|
|
2022-02-13 14:54:05 +01:00
|
|
|
|
2017-08-11 14:54:32 -06:00
|
|
|
|
2021-09-17 21:13:24 +08:00
|
|
|
|
2017-08-11 14:54:32 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2020-05-27 23:02:40 -04:00
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2018-05-18 13:28:02 -06:00
|
|
|
|
2021-02-10 09:13:15 -07:00
|
|
|
|
|
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2023-01-19 19:15:20 -08:00
|
|
|
|
2023-01-19 19:15:21 -08:00
|
|
|
|
2024-10-11 10:56:57 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2023-02-24 13:28:11 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-06-26 10:07:01 -07:00
|
|
|
|
x86/PCI: Add driver for Intel Volume Management Device (VMD)
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
2016-01-12 13:18:10 -07:00
|
|
|
|
|
|
|
|
|
