linux/drivers/usb/gadget/function/storage_common.c

541 lines
13 KiB

usb: gadget: storage: make FSG_NUM_BUFFERS variable size FSG_NUM_BUFFERS is set to 2 as default. Usually 2 buffers are enough to establish a good buffering pipeline. The number may be increased in order to compensate a for bursty VFS behaviour. Here follows a description of system that may require more than 2 buffers. * CPU ondemand governor active * latency cost for wake up and/or frequency change * DMA for IO Use case description. * Data transfer from MMC via VFS to USB. * DMA shuffles data from MMC and to USB. * The CPU wakes up every now and then to pass data in and out from VFS, which cause the bursty VFS behaviour. Test set up * Running dd on the host reading from the mass storage device * cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100)) * Caches are dropped on the host and on the device before each run Measurements on a Snowball board with ondemand_governor active. FSG_NUM_BUFFERS 2 104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s 104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s 104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s FSG_NUM_BUFFERS 4 104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s 104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s There may not be one optimal number for all boards. This is why the number is added to Kconfig. If selecting USB_GADGET_DEBUG_FILES this value may be set by a module parameter as well. Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Michal Nazarewicz <mina86@mina86.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-08-19 21:21:27 +02:00
usb: gadget: storage: adapt logic block size to bound block devices Now the mass storage driver has fixed logic block size of 512 bytes. The mass storage gadget read/write bound devices only through VFS, so the bottom level devices actually are just RAW devices to the driver and connected PC. As a RAW, hosts can always format, read and write it right in 512 bytes logic block and don't care about the actual logic block size of devices bound to the gadget. But if we want to share the bound block device partition between target board and PC, in case the logic block size of the bound block device is 4KB, we execute the following steps: 1. connect a board with mass storage gadget to PC(the board has set one partition of on-board block device as file name of the mass storage) 2. PC format the mass storage to VFAT by default logic block size and read/write it 3. disconnect boards from PC 4. target board mount the partition as VFAT Step 4 will fail since kernel on target thinks the logic block size of the bound partition as 4KB. A typical error is "FAT: logical sector size too small for device (logical sector size = 512)" If we execute opposite steps: 1. format the partition to VFAT on target board and read/write this partition 2. connect the board to Windows PC as usb mass storage gadget, windows will think the disk is not formatted So the conclusion is that only as a gadget, the mass storage driver has no any problem. But being shared VFAT or other filesystem on PC and target board, it will fail. This patch adapts logic block size to bound block devices and fix the issue. Cc: Michal Nazarewicz <mina86@mina86.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peiyu Li <peiyu.li@csr.com> Signed-off-by: Xianglong Du <xianglong.du@csr.com> Signed-off-by: Huayi Li <huayi.li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-08-17 22:52:59 -07:00
usb: gadget: storage: adapt logic block size to bound block devices Now the mass storage driver has fixed logic block size of 512 bytes. The mass storage gadget read/write bound devices only through VFS, so the bottom level devices actually are just RAW devices to the driver and connected PC. As a RAW, hosts can always format, read and write it right in 512 bytes logic block and don't care about the actual logic block size of devices bound to the gadget. But if we want to share the bound block device partition between target board and PC, in case the logic block size of the bound block device is 4KB, we execute the following steps: 1. connect a board with mass storage gadget to PC(the board has set one partition of on-board block device as file name of the mass storage) 2. PC format the mass storage to VFAT by default logic block size and read/write it 3. disconnect boards from PC 4. target board mount the partition as VFAT Step 4 will fail since kernel on target thinks the logic block size of the bound partition as 4KB. A typical error is "FAT: logical sector size too small for device (logical sector size = 512)" If we execute opposite steps: 1. format the partition to VFAT on target board and read/write this partition 2. connect the board to Windows PC as usb mass storage gadget, windows will think the disk is not formatted So the conclusion is that only as a gadget, the mass storage driver has no any problem. But being shared VFAT or other filesystem on PC and target board, it will fail. This patch adapts logic block size to bound block devices and fix the issue. Cc: Michal Nazarewicz <mina86@mina86.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peiyu Li <peiyu.li@csr.com> Signed-off-by: Xianglong Du <xianglong.du@csr.com> Signed-off-by: Huayi Li <huayi.li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-08-17 22:52:59 -07:00
usb: gadget: storage: adapt logic block size to bound block devices Now the mass storage driver has fixed logic block size of 512 bytes. The mass storage gadget read/write bound devices only through VFS, so the bottom level devices actually are just RAW devices to the driver and connected PC. As a RAW, hosts can always format, read and write it right in 512 bytes logic block and don't care about the actual logic block size of devices bound to the gadget. But if we want to share the bound block device partition between target board and PC, in case the logic block size of the bound block device is 4KB, we execute the following steps: 1. connect a board with mass storage gadget to PC(the board has set one partition of on-board block device as file name of the mass storage) 2. PC format the mass storage to VFAT by default logic block size and read/write it 3. disconnect boards from PC 4. target board mount the partition as VFAT Step 4 will fail since kernel on target thinks the logic block size of the bound partition as 4KB. A typical error is "FAT: logical sector size too small for device (logical sector size = 512)" If we execute opposite steps: 1. format the partition to VFAT on target board and read/write this partition 2. connect the board to Windows PC as usb mass storage gadget, windows will think the disk is not formatted So the conclusion is that only as a gadget, the mass storage driver has no any problem. But being shared VFAT or other filesystem on PC and target board, it will fail. This patch adapts logic block size to bound block devices and fix the issue. Cc: Michal Nazarewicz <mina86@mina86.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peiyu Li <peiyu.li@csr.com> Signed-off-by: Xianglong Du <xianglong.du@csr.com> Signed-off-by: Huayi Li <huayi.li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-08-17 22:52:59 -07:00
usb: gadget: storage: adapt logic block size to bound block devices Now the mass storage driver has fixed logic block size of 512 bytes. The mass storage gadget read/write bound devices only through VFS, so the bottom level devices actually are just RAW devices to the driver and connected PC. As a RAW, hosts can always format, read and write it right in 512 bytes logic block and don't care about the actual logic block size of devices bound to the gadget. But if we want to share the bound block device partition between target board and PC, in case the logic block size of the bound block device is 4KB, we execute the following steps: 1. connect a board with mass storage gadget to PC(the board has set one partition of on-board block device as file name of the mass storage) 2. PC format the mass storage to VFAT by default logic block size and read/write it 3. disconnect boards from PC 4. target board mount the partition as VFAT Step 4 will fail since kernel on target thinks the logic block size of the bound partition as 4KB. A typical error is "FAT: logical sector size too small for device (logical sector size = 512)" If we execute opposite steps: 1. format the partition to VFAT on target board and read/write this partition 2. connect the board to Windows PC as usb mass storage gadget, windows will think the disk is not formatted So the conclusion is that only as a gadget, the mass storage driver has no any problem. But being shared VFAT or other filesystem on PC and target board, it will fail. This patch adapts logic block size to bound block devices and fix the issue. Cc: Michal Nazarewicz <mina86@mina86.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peiyu Li <peiyu.li@csr.com> Signed-off-by: Xianglong Du <xianglong.du@csr.com> Signed-off-by: Huayi Li <huayi.li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-08-17 22:52:59 -07:00
usb: gadget: add missing MODULE_DESCRIPTION() macros make allmodconfig && make W=1 C=1 reports: WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/libcomposite.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_acm.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_ss_lb.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/u_serial.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_serial.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_obex.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/u_ether.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_ncm.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_ecm.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_phonet.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_eem.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_ecm_subset.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_rndis.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_mass_storage.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_fs.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_uac1.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_uac1_legacy.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_uac2.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_uvc.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_midi.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_midi2.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_hid.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_printer.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/function/usb_f_tcm.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/legacy/g_zero.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/legacy/g_midi.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/gadget/legacy/g_dbgp.o Add the missing invocations of the MODULE_DESCRIPTION() macro. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://lore.kernel.org/r/20240605-md-drivers-usb-gadget-v1-1-29847a46aad3@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-06-05 20:57:08 -07:00