linux/drivers/firmware/ti_sci.c

4080 lines
114 KiB

firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Partial-IO support Add support for Partial-IO poweroff. In Partial-IO pins of a few hardware units can generate system wakeups while DDR memory is not powered resulting in a fresh boot of the system. These hardware units in the SoC are always powered so that some logic can detect pin activity. If the system supports Partial-IO as described in the fw capabilities, a sys_off handler is added. This sys_off handler decides if the poweroff is executed by entering normal poweroff or Partial-IO instead. The decision is made by checking if wakeup is enabled on all devices that may wake up the SoC from Partial-IO. The possible wakeup devices are found by checking which devices reference a "Partial-IO" system state in the list of wakeup-source system states. Only devices that are actually enabled by the user will be considered as an active wakeup source. If none of the wakeup sources is enabled the system will do a normal poweroff. If at least one wakeup source is enabled it will instead send a TI_SCI_MSG_PREPARE_SLEEP message from the sys_off handler. Sending this message will result in an immediate shutdown of the system. No execution is expected after this point. The code will wait for 5s and do an emergency_restart afterwards if Partial-IO wasn't entered at that point. A short documentation about Partial-IO can be found in section 6.2.4.5 of the TRM at https://www.ti.com/lit/pdf/spruiv7 Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Kendall Willis <k-willis@ti.com> Reviewed-by: Sebin Francis <sebin.francis@ti.com> Link: https://patch.msgid.link/20251103-topic-am62-partialio-v6-12-b4-v10-2-0557e858d747@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-11-03 13:42:20 +01:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Partial-IO support Add support for Partial-IO poweroff. In Partial-IO pins of a few hardware units can generate system wakeups while DDR memory is not powered resulting in a fresh boot of the system. These hardware units in the SoC are always powered so that some logic can detect pin activity. If the system supports Partial-IO as described in the fw capabilities, a sys_off handler is added. This sys_off handler decides if the poweroff is executed by entering normal poweroff or Partial-IO instead. The decision is made by checking if wakeup is enabled on all devices that may wake up the SoC from Partial-IO. The possible wakeup devices are found by checking which devices reference a "Partial-IO" system state in the list of wakeup-source system states. Only devices that are actually enabled by the user will be considered as an active wakeup source. If none of the wakeup sources is enabled the system will do a normal poweroff. If at least one wakeup source is enabled it will instead send a TI_SCI_MSG_PREPARE_SLEEP message from the sys_off handler. Sending this message will result in an immediate shutdown of the system. No execution is expected after this point. The code will wait for 5s and do an emergency_restart afterwards if Partial-IO wasn't entered at that point. A short documentation about Partial-IO can be found in section 6.2.4.5 of the TRM at https://www.ti.com/lit/pdf/spruiv7 Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Kendall Willis <k-willis@ti.com> Reviewed-by: Sebin Francis <sebin.francis@ti.com> Link: https://patch.msgid.link/20251103-topic-am62-partialio-v6-12-b4-v10-2-0557e858d747@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-11-03 13:42:20 +01:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Partial-IO support Add support for Partial-IO poweroff. In Partial-IO pins of a few hardware units can generate system wakeups while DDR memory is not powered resulting in a fresh boot of the system. These hardware units in the SoC are always powered so that some logic can detect pin activity. If the system supports Partial-IO as described in the fw capabilities, a sys_off handler is added. This sys_off handler decides if the poweroff is executed by entering normal poweroff or Partial-IO instead. The decision is made by checking if wakeup is enabled on all devices that may wake up the SoC from Partial-IO. The possible wakeup devices are found by checking which devices reference a "Partial-IO" system state in the list of wakeup-source system states. Only devices that are actually enabled by the user will be considered as an active wakeup source. If none of the wakeup sources is enabled the system will do a normal poweroff. If at least one wakeup source is enabled it will instead send a TI_SCI_MSG_PREPARE_SLEEP message from the sys_off handler. Sending this message will result in an immediate shutdown of the system. No execution is expected after this point. The code will wait for 5s and do an emergency_restart afterwards if Partial-IO wasn't entered at that point. A short documentation about Partial-IO can be found in section 6.2.4.5 of the TRM at https://www.ti.com/lit/pdf/spruiv7 Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Kendall Willis <k-willis@ti.com> Reviewed-by: Sebin Francis <sebin.francis@ti.com> Link: https://patch.msgid.link/20251103-topic-am62-partialio-v6-12-b4-v10-2-0557e858d747@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-11-03 13:42:20 +01:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Introduce Power Management Ops Introduce power management ops supported by the TISCI Low Power Mode API [1]. 1) TISCI_MSG_LPM_WAKE_REASON Get which wake up source woke the SoC from Low Power Mode. The wake up source IDs will be common for all K3 platforms. 2) TISCI_MSG_LPM_SET_DEVICE_CONSTRAINT Set LPM constraint on behalf of a device. By setting a constraint, the device ensures that it will not be powered off or reset in the selected mode. 3) TISCI_MSG_LPM_SET_LATENCY_CONSTRAINT Set LPM resume latency constraint. By setting a constraint, the host ensures that the resume time from selected mode will be less than the constraint value. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [g-vlaev@ti.com: LPM_WAKE_REASON and IO_ISOLATION support] Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [a-kaur@ti.com: SET_DEVICE_CONSTRAINT support] Signed-off-by: Akashdeep Kaur <a-kaur@ti.com> [vibhore@ti.com: SET_LATENCY_CONSTRAINT support] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Akashdeep Kaur <a-kaur@ti.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-4-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:57 +02:00
2023-06-20 21:16:19 -05:00
2023-06-20 21:16:19 -05:00
2023-06-20 21:16:19 -05:00
firmware: ti_sci: Introduce Power Management Ops Introduce power management ops supported by the TISCI Low Power Mode API [1]. 1) TISCI_MSG_LPM_WAKE_REASON Get which wake up source woke the SoC from Low Power Mode. The wake up source IDs will be common for all K3 platforms. 2) TISCI_MSG_LPM_SET_DEVICE_CONSTRAINT Set LPM constraint on behalf of a device. By setting a constraint, the device ensures that it will not be powered off or reset in the selected mode. 3) TISCI_MSG_LPM_SET_LATENCY_CONSTRAINT Set LPM resume latency constraint. By setting a constraint, the host ensures that the resume time from selected mode will be less than the constraint value. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [g-vlaev@ti.com: LPM_WAKE_REASON and IO_ISOLATION support] Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [a-kaur@ti.com: SET_DEVICE_CONSTRAINT support] Signed-off-by: Akashdeep Kaur <a-kaur@ti.com> [vibhore@ti.com: SET_LATENCY_CONSTRAINT support] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Akashdeep Kaur <a-kaur@ti.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-4-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:57 +02:00
firmware: ti_sci: Introduce Power Management Ops Introduce power management ops supported by the TISCI Low Power Mode API [1]. 1) TISCI_MSG_LPM_WAKE_REASON Get which wake up source woke the SoC from Low Power Mode. The wake up source IDs will be common for all K3 platforms. 2) TISCI_MSG_LPM_SET_DEVICE_CONSTRAINT Set LPM constraint on behalf of a device. By setting a constraint, the device ensures that it will not be powered off or reset in the selected mode. 3) TISCI_MSG_LPM_SET_LATENCY_CONSTRAINT Set LPM resume latency constraint. By setting a constraint, the host ensures that the resume time from selected mode will be less than the constraint value. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [g-vlaev@ti.com: LPM_WAKE_REASON and IO_ISOLATION support] Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [a-kaur@ti.com: SET_DEVICE_CONSTRAINT support] Signed-off-by: Akashdeep Kaur <a-kaur@ti.com> [vibhore@ti.com: SET_LATENCY_CONSTRAINT support] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Akashdeep Kaur <a-kaur@ti.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-4-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:57 +02:00
2023-06-20 21:16:19 -05:00
firmware: ti_sci: Partial-IO support Add support for Partial-IO poweroff. In Partial-IO pins of a few hardware units can generate system wakeups while DDR memory is not powered resulting in a fresh boot of the system. These hardware units in the SoC are always powered so that some logic can detect pin activity. If the system supports Partial-IO as described in the fw capabilities, a sys_off handler is added. This sys_off handler decides if the poweroff is executed by entering normal poweroff or Partial-IO instead. The decision is made by checking if wakeup is enabled on all devices that may wake up the SoC from Partial-IO. The possible wakeup devices are found by checking which devices reference a "Partial-IO" system state in the list of wakeup-source system states. Only devices that are actually enabled by the user will be considered as an active wakeup source. If none of the wakeup sources is enabled the system will do a normal poweroff. If at least one wakeup source is enabled it will instead send a TI_SCI_MSG_PREPARE_SLEEP message from the sys_off handler. Sending this message will result in an immediate shutdown of the system. No execution is expected after this point. The code will wait for 5s and do an emergency_restart afterwards if Partial-IO wasn't entered at that point. A short documentation about Partial-IO can be found in section 6.2.4.5 of the TRM at https://www.ti.com/lit/pdf/spruiv7 Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Kendall Willis <k-willis@ti.com> Reviewed-by: Sebin Francis <sebin.francis@ti.com> Link: https://patch.msgid.link/20251103-topic-am62-partialio-v6-12-b4-v10-2-0557e858d747@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-11-03 13:42:20 +01:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Introduce Power Management Ops Introduce power management ops supported by the TISCI Low Power Mode API [1]. 1) TISCI_MSG_LPM_WAKE_REASON Get which wake up source woke the SoC from Low Power Mode. The wake up source IDs will be common for all K3 platforms. 2) TISCI_MSG_LPM_SET_DEVICE_CONSTRAINT Set LPM constraint on behalf of a device. By setting a constraint, the device ensures that it will not be powered off or reset in the selected mode. 3) TISCI_MSG_LPM_SET_LATENCY_CONSTRAINT Set LPM resume latency constraint. By setting a constraint, the host ensures that the resume time from selected mode will be less than the constraint value. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [g-vlaev@ti.com: LPM_WAKE_REASON and IO_ISOLATION support] Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [a-kaur@ti.com: SET_DEVICE_CONSTRAINT support] Signed-off-by: Akashdeep Kaur <a-kaur@ti.com> [vibhore@ti.com: SET_LATENCY_CONSTRAINT support] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Akashdeep Kaur <a-kaur@ti.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-4-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:57 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Introduce Power Management Ops Introduce power management ops supported by the TISCI Low Power Mode API [1]. 1) TISCI_MSG_LPM_WAKE_REASON Get which wake up source woke the SoC from Low Power Mode. The wake up source IDs will be common for all K3 platforms. 2) TISCI_MSG_LPM_SET_DEVICE_CONSTRAINT Set LPM constraint on behalf of a device. By setting a constraint, the device ensures that it will not be powered off or reset in the selected mode. 3) TISCI_MSG_LPM_SET_LATENCY_CONSTRAINT Set LPM resume latency constraint. By setting a constraint, the host ensures that the resume time from selected mode will be less than the constraint value. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Signed-off-by: Dave Gerlach <d-gerlach@ti.com> [g-vlaev@ti.com: LPM_WAKE_REASON and IO_ISOLATION support] Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [a-kaur@ti.com: SET_DEVICE_CONSTRAINT support] Signed-off-by: Akashdeep Kaur <a-kaur@ti.com> [vibhore@ti.com: SET_LATENCY_CONSTRAINT support] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Akashdeep Kaur <a-kaur@ti.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-4-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:57 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Add support for querying the firmware caps Add support for the TISCI_MSG_QUERY_FW_CAPS message, used to retrieve the firmware capabilities of the currently running system firmware. The message belongs to the TISCI general core message API [1] and is available in SysFW version 08.04.03 and above. Currently, the message is supported on devices with split architecture of the system firmware (DM + TIFS) like AM62x. Old revisions or not yet supported platforms will NACK this request. We're using this message locally in ti_sci.c to get the low power features of the FW/SoC. As there's no other kernel consumers yet, this is not added to struct ti_sci_core_ops. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html [2] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/general/core.html#tisci-msg-query-fw-caps Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> [vibhore@ti.com: Support for LPM_DM_MANAGED mode] Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Acked-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-2-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:55 +02:00
firmware: ti_sci: Partial-IO support Add support for Partial-IO poweroff. In Partial-IO pins of a few hardware units can generate system wakeups while DDR memory is not powered resulting in a fresh boot of the system. These hardware units in the SoC are always powered so that some logic can detect pin activity. If the system supports Partial-IO as described in the fw capabilities, a sys_off handler is added. This sys_off handler decides if the poweroff is executed by entering normal poweroff or Partial-IO instead. The decision is made by checking if wakeup is enabled on all devices that may wake up the SoC from Partial-IO. The possible wakeup devices are found by checking which devices reference a "Partial-IO" system state in the list of wakeup-source system states. Only devices that are actually enabled by the user will be considered as an active wakeup source. If none of the wakeup sources is enabled the system will do a normal poweroff. If at least one wakeup source is enabled it will instead send a TI_SCI_MSG_PREPARE_SLEEP message from the sys_off handler. Sending this message will result in an immediate shutdown of the system. No execution is expected after this point. The code will wait for 5s and do an emergency_restart afterwards if Partial-IO wasn't entered at that point. A short documentation about Partial-IO can be found in section 6.2.4.5 of the TRM at https://www.ti.com/lit/pdf/spruiv7 Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Kendall Willis <k-willis@ti.com> Reviewed-by: Sebin Francis <sebin.francis@ti.com> Link: https://patch.msgid.link/20251103-topic-am62-partialio-v6-12-b4-v10-2-0557e858d747@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-11-03 13:42:20 +01:00
firmware: ti_sci: Partial-IO support Add support for Partial-IO poweroff. In Partial-IO pins of a few hardware units can generate system wakeups while DDR memory is not powered resulting in a fresh boot of the system. These hardware units in the SoC are always powered so that some logic can detect pin activity. If the system supports Partial-IO as described in the fw capabilities, a sys_off handler is added. This sys_off handler decides if the poweroff is executed by entering normal poweroff or Partial-IO instead. The decision is made by checking if wakeup is enabled on all devices that may wake up the SoC from Partial-IO. The possible wakeup devices are found by checking which devices reference a "Partial-IO" system state in the list of wakeup-source system states. Only devices that are actually enabled by the user will be considered as an active wakeup source. If none of the wakeup sources is enabled the system will do a normal poweroff. If at least one wakeup source is enabled it will instead send a TI_SCI_MSG_PREPARE_SLEEP message from the sys_off handler. Sending this message will result in an immediate shutdown of the system. No execution is expected after this point. The code will wait for 5s and do an emergency_restart afterwards if Partial-IO wasn't entered at that point. A short documentation about Partial-IO can be found in section 6.2.4.5 of the TRM at https://www.ti.com/lit/pdf/spruiv7 Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Kendall Willis <k-willis@ti.com> Reviewed-by: Sebin Francis <sebin.francis@ti.com> Link: https://patch.msgid.link/20251103-topic-am62-partialio-v6-12-b4-v10-2-0557e858d747@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-11-03 13:42:20 +01:00
firmware: ti_sci: Add system suspend and resume call Introduce system suspend call that enables the ti_sci driver to support low power mode when the user space issues a suspend to mem. The following power management operations defined in the TISCI Low Power Mode API [1] are implemented to support suspend and resume: 1) TISCI_MSG_PREPARE_SLEEP Prepare the SOC for entering into a low power mode and provide details to firmware about the state being entered. 2) TISCI_MSG_SET_IO_ISOLATION Control the IO isolation for Low Power Mode. Also, write a ti_sci_prepare_system_suspend call to be used in the driver suspend handler to allow the system to identify the low power mode being entered and if necessary, send TISCI_MSG_PREPARE_SLEEP with information about the mode being entered. Sysfw version >= 10.00.04 support LPM_DM_MANAGED capability [2], where Device Mgr firmware now manages which low power mode is chosen. Going forward, this is the default configuration supported for TI AM62 family of devices. The state chosen by the DM can be influenced by sending constraints using the new LPM constraint APIs. In case the firmware does not support LPM_DM_MANAGED mode, the mode selection logic can be extended as needed. If no suspend-to-RAM modes are supported, return without taking any action. We're using "pm_suspend_target_state" to map the kernel's target suspend state to SysFW low power mode. Make sure this is available only when CONFIG_SUSPEND is enabled. Suspend has to be split into two parts, ti_sci_suspend() will send the prepare sleep message to prepare suspend. ti_sci_suspend_noirq() sets IO isolation which needs to be done as late as possible to avoid any issues. On resume this has to be done as early as possible. [1] https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/pm/lpm.html Co-developed-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Vibhore Vardhan <vibhore@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com> Tested-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241007-tisci-syssuspendresume-v13-3-ed54cd659a49@baylibre.com Signed-off-by: Nishanth Menon <nm@ti.com>
2024-10-07 08:08:56 +02:00