linux/arch/powerpc/include/asm/page.h

386 lines
11 KiB

powerpc/44x: Support for 256KB PAGE_SIZE This patch adds support for 256KB pages on ppc44x-based boards. For simplification of implementation with 256KB pages we still assume 2-level paging. As a side effect this leads to wasting extra memory space reserved for PTE tables: only 1/4 of pages allocated for PTEs are actually used. But this may be an acceptable trade-off to achieve the high performance we have with big PAGE_SIZEs in some applications (e.g. RAID). Also with 256KB PAGE_SIZE we increase THREAD_SIZE up to 32KB to minimize the risk of stack overflows in the cases of on-stack arrays, which size depends on the page size (e.g. multipage BIOs, NTFS, etc.). With 256KB PAGE_SIZE we need to decrease the PKMAP_ORDER at least down to 9, otherwise all high memory (2 ^ 10 * PAGE_SIZE == 256MB) we'll be occupied by PKMAP addresses leaving no place for vmalloc. We do not separate PKMAP_ORDER for 256K from 16K/64K PAGE_SIZE here; actually that value of 10 in support for 16K/64K had been selected rather intuitively. Thus now for all cases of PAGE_SIZE on ppc44x (including the default, 4KB, one) we have 512 pages for PKMAP. Because ELF standard supports only page sizes up to 64K, then you should use binutils later than 2.17.50.0.3 with '-zmax-page-size' set to 256K for building applications, which are to be run with the 256KB-page sized kernel. If using the older binutils, then you should patch them like follows: --- binutils/bfd/elf32-ppc.c.orig +++ binutils/bfd/elf32-ppc.c -#define ELF_MAXPAGESIZE 0x10000 +#define ELF_MAXPAGESIZE 0x40000 One more restriction we currently have with 256KB page sizes is inability to use shmem safely, so, for now, the 256KB is available only if you turn the CONFIG_SHMEM option off (another variant is to use BROKEN). Though, if you need shmem with 256KB pages, you can always remove the !SHMEM dependency in 'config PPC_256K_PAGES', and use the workaround available here: http://lkml.org/lkml/2008/12/19/20 Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-01-29 01:40:44 +00:00
powerpc/44x: Support for 256KB PAGE_SIZE This patch adds support for 256KB pages on ppc44x-based boards. For simplification of implementation with 256KB pages we still assume 2-level paging. As a side effect this leads to wasting extra memory space reserved for PTE tables: only 1/4 of pages allocated for PTEs are actually used. But this may be an acceptable trade-off to achieve the high performance we have with big PAGE_SIZEs in some applications (e.g. RAID). Also with 256KB PAGE_SIZE we increase THREAD_SIZE up to 32KB to minimize the risk of stack overflows in the cases of on-stack arrays, which size depends on the page size (e.g. multipage BIOs, NTFS, etc.). With 256KB PAGE_SIZE we need to decrease the PKMAP_ORDER at least down to 9, otherwise all high memory (2 ^ 10 * PAGE_SIZE == 256MB) we'll be occupied by PKMAP addresses leaving no place for vmalloc. We do not separate PKMAP_ORDER for 256K from 16K/64K PAGE_SIZE here; actually that value of 10 in support for 16K/64K had been selected rather intuitively. Thus now for all cases of PAGE_SIZE on ppc44x (including the default, 4KB, one) we have 512 pages for PKMAP. Because ELF standard supports only page sizes up to 64K, then you should use binutils later than 2.17.50.0.3 with '-zmax-page-size' set to 256K for building applications, which are to be run with the 256KB-page sized kernel. If using the older binutils, then you should patch them like follows: --- binutils/bfd/elf32-ppc.c.orig +++ binutils/bfd/elf32-ppc.c -#define ELF_MAXPAGESIZE 0x10000 +#define ELF_MAXPAGESIZE 0x40000 One more restriction we currently have with 256KB page sizes is inability to use shmem safely, so, for now, the 256KB is available only if you turn the CONFIG_SHMEM option off (another variant is to use BROKEN). Though, if you need shmem with 256KB pages, you can always remove the !SHMEM dependency in 'config PPC_256K_PAGES', and use the workaround available here: http://lkml.org/lkml/2008/12/19/20 Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-01-29 01:40:44 +00:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-14 22:58:37 +00:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-14 22:58:37 +00:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-14 22:58:37 +00:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
2008-08-30 11:43:47 +10:00
powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-14 22:58:37 +00:00
2008-08-30 11:43:47 +10:00
2008-08-30 11:43:47 +10:00
[POWERPC] 85xx: Add support for relocatable kernel (and booting at non-zero) Added support to allow an 85xx kernel to be run from a non-zero physical address (useful for cooperative asymmetric multiprocessing situations and kdump). The support can be configured at compile time by setting CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as desired. Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this config option causes the kernel to determine at runtime the physical addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning. However, CONFIG_PHYSICAL_START will always be used to set the LOAD program header physical address field in the resulting ELF image. Currently we are limited to running at a physical address that is a multiple of 256M. This is due to how we map TLBs to cover lowmem. This should be fixed to allow 64M or maybe even 16M alignment in the future. It is considered an error to try and run a kernel at a non-aligned physical address. All the magic for this support is accomplished by proper initialization of the kernel memory subsystem and use of ARCH_PFN_OFFSET. The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings. ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET. /dev/mem continues to allow access to any physical address in the system regardless of how CONFIG_PHYSICAL_START is set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-04-22 04:22:34 +10:00
powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-14 22:58:37 +00:00
powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2011-12-14 22:58:37 +00:00
2008-08-30 11:43:47 +10:00
powerpc/mm: Allow more flexible layouts for hugepage pagetables Currently each available hugepage size uses a slightly different pagetable layout: that is, the bottem level table of pointers to hugepages is a different size, and may branch off from the normal page tables at a different level. Every hugepage aware path that needs to walk the pagetables must therefore look up the hugepage size from the slice info first, and work out the correct way to walk the pagetables accordingly. Future hardware is likely to add more possible hugepage sizes, more layout options and more mess. This patch, therefore reworks the handling of hugepage pagetables to reduce this complexity. In the new scheme, instead of having to consult the slice mask, pagetable walking code can check a flag in the PGD/PUD/PMD entries to see where to branch off to hugepage pagetables, and the entry also contains the information (eseentially hugepage shift) necessary to then interpret that table without recourse to the slice mask. This scheme can be extended neatly to handle multiple levels of self-describing "special" hugepage pagetables, although for now we assume only one level exists. This approach means that only the pagetable allocation path needs to know how the pagetables should be set out. All other (hugepage) pagetable walking paths can just interpret the structure as they go. There already was a flag bit in PGD/PUD/PMD entries for hugepage directory pointers, but it was only used for debug. We alter that flag bit to instead be a 0 in the MSB to indicate a hugepage pagetable pointer (normally it would be 1 since the pointer lies in the linear mapping). This means that asm pagetable walking can test for (and punt on) hugepage pointers with the same test that checks for unpopulated page directory entries (beq becomes bge), since hugepage pointers will always be positive, and normal pointers always negative. While we're at it, we get rid of the confusing (and grep defeating) #defining of hugepte_shift to be the same thing as mmu_huge_psizes. Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-10-26 19:24:31 +00:00
CONFIG_HIGHPTE vs. sub-page page tables. Background: I've implemented 1K/2K page tables for s390. These sub-page page tables are required to properly support the s390 virtualization instruction with KVM. The SIE instruction requires that the page tables have 256 page table entries (pte) followed by 256 page status table entries (pgste). The pgstes are only required if the process is using the SIE instruction. The pgstes are updated by the hardware and by the hypervisor for a number of reasons, one of them is dirty and reference bit tracking. To avoid wasting memory the standard pte table allocation should return 1K/2K (31/64 bit) and 2K/4K if the process is using SIE. Problem: Page size on s390 is 4K, page table size is 1K or 2K. That means the s390 version for pte_alloc_one cannot return a pointer to a struct page. Trouble is that with the CONFIG_HIGHPTE feature on x86 pte_alloc_one cannot return a pointer to a pte either, since that would require more than 32 bit for the return value of pte_alloc_one (and the pte * would not be accessible since its not kmapped). Solution: The only solution I found to this dilemma is a new typedef: a pgtable_t. For s390 pgtable_t will be a (pte *) - to be introduced with a later patch. For everybody else it will be a (struct page *). The additional problem with the initialization of the ptl lock and the NR_PAGETABLE accounting is solved with a constructor pgtable_page_ctor and a destructor pgtable_page_dtor. The page table allocation and free functions need to call these two whenever a page table page is allocated or freed. pmd_populate will get a pgtable_t instead of a struct page pointer. To get the pgtable_t back from a pmd entry that has been installed with pmd_populate a new function pmd_pgtable is added. It replaces the pmd_page call in free_pte_range and apply_to_pte_range. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-08 04:22:04 -08:00