2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: add PCI Express ASPM support
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-25 09:46:41 +08:00
|
|
|
|
2012-04-30 15:21:02 -06:00
|
|
|
|
2005-04-08 14:53:31 +09:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-13 22:30:39 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2007-07-15 23:39:39 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-13 22:30:39 -08:00
|
|
|
|
2007-07-15 23:39:39 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-13 22:30:39 -08:00
|
|
|
|
|
|
|
|
|
2007-07-15 23:39:39 -07:00
|
|
|
|
2008-02-13 22:30:39 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-07-15 23:39:39 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:36 -07:00
|
|
|
|
2011-04-11 11:37:07 +10:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
2011-05-12 17:11:39 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2006-11-29 13:53:10 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
2006-11-29 13:53:10 -08:00
|
|
|
|
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:29 -06:00
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:29 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:29 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:29 -06:00
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
|
|
|
|
|
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:29 -06:00
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-14 13:04:29 -06:00
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
2008-11-22 02:40:40 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2008-11-22 02:40:40 +08:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-07-16 10:19:22 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2009-10-29 17:24:59 +02:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
2010-07-16 10:19:22 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-10-29 17:24:59 +02:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-04-22 09:02:43 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2010-04-22 09:02:43 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2011-05-23 17:12:22 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:39:00 -04:00
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2009-10-27 13:26:47 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
2010-04-22 09:02:43 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2010-04-22 09:02:43 -06:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-06 12:08:18 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-08-23 10:53:08 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-06-14 13:04:35 -06:00
|
|
|
|
2006-11-29 13:53:10 -08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-07-28 13:38:59 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-09 13:38:57 -06:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2012-07-09 13:38:57 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-09 13:38:57 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-06-19 07:45:44 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2012-06-19 07:45:44 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2012-07-09 13:38:41 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2012-07-09 13:38:57 -06:00
|
|
|
|
|
|
|
|
|
2009-10-27 13:26:47 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-06-19 07:45:44 -06:00
|
|
|
|
|
|
|
|
|
2012-07-09 13:38:41 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2009-10-27 13:26:47 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-06-19 07:45:44 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-06-19 07:45:44 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-06-19 07:45:44 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2008-06-13 10:52:11 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-09 13:38:41 -06:00
|
|
|
|
2009-04-23 20:48:32 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2009-10-27 13:26:47 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:36 -07:00
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:26 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:26 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:36 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:26 -07:00
|
|
|
|
|
|
|
|
|
2010-02-23 10:24:21 -07:00
|
|
|
|
|
|
|
|
|
2007-03-26 21:53:30 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-02-28 15:34:49 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-06-10 15:28:50 -06:00
|
|
|
|
2010-02-23 10:24:36 -07:00
|
|
|
|
2009-12-13 08:11:32 -05:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:32 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:35 -05:00
|
|
|
|
2009-12-13 08:11:32 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-12-05 13:51:18 -07:00
|
|
|
|
2009-12-13 08:11:32 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:34 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:34 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-12-05 13:51:17 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
2012-12-05 13:51:17 -07:00
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
2012-12-05 13:51:17 -07:00
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-12-05 13:51:17 -07:00
|
|
|
|
|
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-24 17:20:06 +08:00
|
|
|
|
2012-12-05 13:51:18 -07:00
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
2012-07-24 17:20:06 +08:00
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-04-18 13:53:55 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-02-14 18:52:22 +02:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
|
|
|
|
|
2008-10-30 02:17:49 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-11-22 02:41:07 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
2011-04-11 11:37:07 +10:00
|
|
|
|
2009-12-13 08:11:33 -05:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-11-22 02:39:32 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-02 22:33:43 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-28 00:25:48 -07:00
|
|
|
|
2006-06-02 12:35:43 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-06-02 12:35:43 +08:00
|
|
|
|
2005-04-28 00:25:48 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-03-26 21:53:30 -08:00
|
|
|
|
2005-06-02 15:41:48 -07:00
|
|
|
|
|
|
|
|
|
2005-09-22 21:06:31 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
2005-06-02 15:41:48 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
2008-10-21 10:06:29 +11:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-01-30 12:25:24 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-21 10:06:29 +11:00
|
|
|
|
|
|
|
|
|
2012-09-10 17:19:33 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-21 10:06:29 +11:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[PATCH] PCI: Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
> On Mon, Feb 13, 2006 at 05:13:21PM -0800, David S. Miller wrote:
> >
> > In drivers/pci/probe.c:pci_scan_bridge(), if this is not the first
> > pass (pass != 0) we don't restore the PCI_BRIDGE_CONTROL_REGISTER and
> > thus leave PCI_BRIDGE_CTL_MASTER_ABORT off:
> >
> > int __devinit pci_scan_bridge(struct pci_bus *bus, struct pci_dev * dev, int max, int pass)
> > {
> > ...
> > /* Disable MasterAbortMode during probing to avoid reporting
> > of bus errors (in some architectures) */
> > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &bctl);
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> > bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
> > ...
> > if ((buses & 0xffff00) && !pcibios_assign_all_busses() && !is_cardbus) {
> > unsigned int cmax, busnr;
> > /*
> > * Bus already configured by firmware, process it in the first
> > * pass and just note the configuration.
> > */
> > if (pass)
> > return max;
> > ...
> > }
> >
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, bctl);
> > ...
> >
> > This doesn't seem intentional.
Agreed, looks like an accident. The patch [1] originally came from Kip
Walker (Broadcom back then) between 2.6.0-test3 and 2.6.0-test4. As I
recall it was supposed to fix an issue with with PCI aborts being
signalled by the PCI bridge of the Broadcom BCM1250 family of SOCs when
probing behind pci_scan_bridge. It is undeseriable to disable
PCI_BRIDGE_CTL_MASTER_ABORT in pci_{read,write)_config_* and the
behaviour wasn't considered a bug in need of a workaround, so this was
put in probe.c.
I don't have an affected system at hand, so can't really test but I
propose something like the below patch.
[1] http://www.linux-mips.org/git?p=linux.git;a=commit;h=599457e0cb702a31a3247ea6a5d9c6c99c4cf195
[PCI] Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-02-14 16:23:57 +00:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 14:56:10 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
2009-03-20 14:56:10 -06:00
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
2009-03-20 14:56:10 -06:00
|
|
|
|
|
|
|
|
|
2010-03-16 15:52:58 -06:00
|
|
|
|
2012-05-17 18:51:13 -07:00
|
|
|
|
2009-03-20 14:56:10 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-09-22 21:06:31 -07:00
|
|
|
|
2008-10-21 10:06:29 +11:00
|
|
|
|
2005-09-22 21:06:31 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[PATCH] PCI: Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
> On Mon, Feb 13, 2006 at 05:13:21PM -0800, David S. Miller wrote:
> >
> > In drivers/pci/probe.c:pci_scan_bridge(), if this is not the first
> > pass (pass != 0) we don't restore the PCI_BRIDGE_CONTROL_REGISTER and
> > thus leave PCI_BRIDGE_CTL_MASTER_ABORT off:
> >
> > int __devinit pci_scan_bridge(struct pci_bus *bus, struct pci_dev * dev, int max, int pass)
> > {
> > ...
> > /* Disable MasterAbortMode during probing to avoid reporting
> > of bus errors (in some architectures) */
> > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &bctl);
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> > bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
> > ...
> > if ((buses & 0xffff00) && !pcibios_assign_all_busses() && !is_cardbus) {
> > unsigned int cmax, busnr;
> > /*
> > * Bus already configured by firmware, process it in the first
> > * pass and just note the configuration.
> > */
> > if (pass)
> > return max;
> > ...
> > }
> >
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, bctl);
> > ...
> >
> > This doesn't seem intentional.
Agreed, looks like an accident. The patch [1] originally came from Kip
Walker (Broadcom back then) between 2.6.0-test3 and 2.6.0-test4. As I
recall it was supposed to fix an issue with with PCI aborts being
signalled by the PCI bridge of the Broadcom BCM1250 family of SOCs when
probing behind pci_scan_bridge. It is undeseriable to disable
PCI_BRIDGE_CTL_MASTER_ABORT in pci_{read,write)_config_* and the
behaviour wasn't considered a bug in need of a workaround, so this was
put in probe.c.
I don't have an affected system at hand, so can't really test but I
propose something like the below patch.
[1] http://www.linux-mips.org/git?p=linux.git;a=commit;h=599457e0cb702a31a3247ea6a5d9c6c99c4cf195
[PCI] Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-02-14 16:23:57 +00:00
|
|
|
|
2005-09-22 21:06:31 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-28 00:25:47 -07:00
|
|
|
|
2011-06-02 11:02:50 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:13 -07:00
|
|
|
|
2011-06-02 11:02:50 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-01-24 21:14:33 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-10-08 16:24:16 -07:00
|
|
|
|
2005-06-02 15:41:48 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2006-01-17 16:57:01 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
|
|
|
|
|
2005-04-28 00:25:47 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-28 00:25:47 -07:00
|
|
|
|
2005-06-02 15:41:48 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:13 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-08 14:00:52 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
PCI: lets kill the 'PCI hidden behind bridge' message
Adrian Bunk wrote:
> Alois Nešpor wrote
>> PCI: Bus #0b (-#0e) is hidden behind transparent bridge #0a (-#0b) (try 'pci=assign-busses')
>> Please report the result to linux-kernel to fix this permanently"
>>
>> dmesg:
>> "Yenta: Raising subordinate bus# of parent bus (#0a) from #0b to #0e"
>> without pci=assign-busses and nothing with pci=assign-busses.
>
> Bernhard?
Ok, lets kill the message. As Alois Nešpor also saw, that's fixed up by Yenta,
so PCI does not have to warn about it. PCI could still warn about it if
is_cardbus is 0 in that instance of pci_scan_bridge(), but so far I have
not seen a report where this would have been the case so I think we can
spare the kernel of that check (removes ~300 lines of asm) unless debugging
is done.
History: The whole check was added in the days before we had the fixup
for this in Yenta and pci=assign-busses was the only way to get CardBus
cards detected on many (not all) of the machines which give this warning.
In theory, there could be cases when this warning would be triggered and
it's not cardbus, then the warning should still apply, but I think this
should only be the case when working on a completely broken PCI setup,
but one may have already enabled the debug code in drivers/pci and the
patched check would then trigger.
I do not sign this off yet because it's completely untested so far, but
everyone is free to test it (with the #ifdef DEBUG replaced by #if 1 and
pr_debug( changed to printk(.
We may also dump the whole check (remove everything within the #ifdef from
the source) if that's perferred.
On Alois Nešpor's machine this would then (only when debugging) this message:
"PCI: Bus #0b (-#0e) is partially hidden behind transparent bridge #0a (-#0b)"
"partially" should be in the message on his machine because #0b of #0b-#0e
is reachable behind #0a-#0b, but not #0c-#0e.
But that differentiation is now moot anyway because the fixup in Yenta takes
care of it as far as I could see so far, which means that unless somebody
is debugging a totally broken PCI setup, this message is not needed anymore,
not even for debugging PCI.
Ok, here the patch with the following changes:
* Refined to say that the bus is only partially hidden when the parent
bus numbers are not totally way off (outside of) the child bus range
* remove the reference to pci=assign-busses and the plea to report it
We could add a pure source code-only comment to keep a reference to
pci=assign-busses the in case when this is triggered by someone who
is debugging the cause of this message and looking the way to solve it.
From: Bernhard Kaindl <bk@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-30 20:35:13 +02:00
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-11-19 17:48:29 -08:00
|
|
|
|
|
|
|
|
|
2009-11-04 10:32:57 -07:00
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
2005-12-08 16:53:12 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
[PATCH] PCI: Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
> On Mon, Feb 13, 2006 at 05:13:21PM -0800, David S. Miller wrote:
> >
> > In drivers/pci/probe.c:pci_scan_bridge(), if this is not the first
> > pass (pass != 0) we don't restore the PCI_BRIDGE_CONTROL_REGISTER and
> > thus leave PCI_BRIDGE_CTL_MASTER_ABORT off:
> >
> > int __devinit pci_scan_bridge(struct pci_bus *bus, struct pci_dev * dev, int max, int pass)
> > {
> > ...
> > /* Disable MasterAbortMode during probing to avoid reporting
> > of bus errors (in some architectures) */
> > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &bctl);
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> > bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
> > ...
> > if ((buses & 0xffff00) && !pcibios_assign_all_busses() && !is_cardbus) {
> > unsigned int cmax, busnr;
> > /*
> > * Bus already configured by firmware, process it in the first
> > * pass and just note the configuration.
> > */
> > if (pass)
> > return max;
> > ...
> > }
> >
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, bctl);
> > ...
> >
> > This doesn't seem intentional.
Agreed, looks like an accident. The patch [1] originally came from Kip
Walker (Broadcom back then) between 2.6.0-test3 and 2.6.0-test4. As I
recall it was supposed to fix an issue with with PCI aborts being
signalled by the PCI bridge of the Broadcom BCM1250 family of SOCs when
probing behind pci_scan_bridge. It is undeseriable to disable
PCI_BRIDGE_CTL_MASTER_ABORT in pci_{read,write)_config_* and the
behaviour wasn't considered a bug in need of a workaround, so this was
put in probe.c.
I don't have an affected system at hand, so can't really test but I
propose something like the below patch.
[1] http://www.linux-mips.org/git?p=linux.git;a=commit;h=599457e0cb702a31a3247ea6a5d9c6c99c4cf195
[PCI] Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-02-14 16:23:57 +00:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-11-02 16:24:32 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-01-26 17:10:03 +00:00
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-11-05 12:05:11 +09:00
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
2012-07-24 17:20:02 +08:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
|
|
|
|
|
2010-01-26 17:10:03 +00:00
|
|
|
|
2009-09-09 14:09:24 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-07-24 17:20:06 +08:00
|
|
|
|
2009-09-09 14:09:24 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-04-23 23:19:36 +02:00
|
|
|
|
2006-12-29 16:47:29 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
|
|
|
|
|
2009-10-06 10:45:19 -05:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-11-05 15:20:34 -05:00
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-07-02 13:24:49 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2007-06-08 15:46:30 -07:00
|
|
|
|
2012-02-19 14:50:12 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-02-19 14:50:12 -08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2009-03-21 22:05:11 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2005-08-17 15:32:19 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-05-28 00:25:05 +08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-10-04 00:41:26 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2006-10-04 00:41:26 +01:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:04 -07:00
|
|
|
|
2006-10-04 00:41:26 +01:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-11-02 16:55:49 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2009-09-09 14:09:24 -07:00
|
|
|
|
2009-10-06 10:45:19 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-06-13 10:52:11 -06:00
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2012-02-19 14:50:12 -08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:11 +08:00
|
|
|
|
2012-02-11 00:18:30 -08:00
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
2011-04-11 11:37:07 +10:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-10-23 11:57:38 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-04-28 16:27:23 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2008-10-13 19:18:07 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-10-13 19:18:07 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-15 01:32:50 -08:00
|
|
|
|
|
|
|
|
|
2008-04-28 16:27:23 -07:00
|
|
|
|
|
|
|
|
|
2009-03-08 21:35:37 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-04-28 16:27:23 -07:00
|
|
|
|
2012-07-24 17:20:06 +08:00
|
|
|
|
2008-04-28 16:27:23 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-15 01:32:50 -08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2007-04-05 17:19:08 +10:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-01-27 10:55:10 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-04-18 13:53:55 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-01-27 10:55:10 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2007-04-05 17:19:09 +10:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-04-11 11:37:07 +10:00
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:14 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-12-07 22:02:58 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-14 14:02:53 +08:00
|
|
|
|
|
|
|
|
|
2013-01-15 11:12:17 +08:00
|
|
|
|
2009-03-20 11:25:11 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-10-07 10:27:17 -07:00
|
|
|
|
|
|
|
|
|
2009-12-04 12:15:21 -08:00
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
|
|
|
|
|
2007-03-26 21:53:30 -08:00
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-01-21 13:20:44 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-02-04 22:27:55 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2008-02-04 22:27:55 -08:00
|
|
|
|
2008-02-04 22:28:14 -08:00
|
|
|
|
2008-02-04 22:27:55 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-15 21:40:31 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-09-09 23:49:59 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-10-13 19:49:55 +08:00
|
|
|
|
|
|
|
|
|
2008-07-07 03:34:48 +02:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-06-02 12:35:43 +08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-06-02 12:35:43 +08:00
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
2008-02-02 22:33:43 +01:00
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 14:56:00 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-11-21 15:07:11 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2013-01-25 09:12:31 -07:00
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
2013-01-25 09:12:31 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-01-17 14:01:41 -07:00
|
|
|
|
2013-01-25 09:12:31 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-01-17 14:01:41 -07:00
|
|
|
|
2013-01-25 09:12:31 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
2013-01-25 09:12:31 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-04-30 15:21:02 -06:00
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
|
|
|
|
|
2012-07-24 17:20:03 +08:00
|
|
|
|
2012-04-30 15:21:02 -06:00
|
|
|
|
2012-07-24 17:20:03 +08:00
|
|
|
|
2012-04-30 15:21:02 -06:00
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-14 14:56:56 -08:00
|
|
|
|
2009-03-20 14:56:05 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2007-03-26 21:53:30 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
2009-03-20 14:56:05 -06:00
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2009-03-20 14:56:05 -06:00
|
|
|
|
2010-01-17 14:01:41 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 14:56:05 -06:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2013-01-25 09:12:31 -07:00
|
|
|
|
2009-12-13 08:10:02 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
PCI: add PCI Express ASPM support
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-25 09:46:41 +08:00
|
|
|
|
2008-07-23 10:32:31 +08:00
|
|
|
|
|
|
|
|
|
PCI: add PCI Express ASPM support
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-25 09:46:41 +08:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-09-13 15:16:33 -03:00
|
|
|
|
2012-07-24 17:20:03 +08:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2012-07-24 17:20:03 +08:00
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-09-08 16:41:18 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-09-08 16:41:18 -05:00
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
|
|
|
|
|
2011-09-08 16:41:18 -05:00
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
2011-09-08 16:41:18 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:16 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:16 -05:00
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:14 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-10-14 14:56:16 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-14 14:56:16 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-03 09:50:20 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-03 09:50:20 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2011-10-03 09:50:20 -05:00
|
|
|
|
|
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-08-02 00:01:18 -05:00
|
|
|
|
PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-20 15:20:54 -05:00
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-05-17 18:51:11 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2009-11-04 10:32:52 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 11:25:13 +08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-03-20 14:56:10 -06:00
|
|
|
|
2009-11-04 10:32:52 -07:00
|
|
|
|
2009-03-20 14:56:10 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2009-11-04 10:32:52 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ACPI / PCI: Set root bridge ACPI handle in advance
The ACPI handles of PCI root bridges need to be known to
acpi_bind_one(), so that it can create the appropriate
"firmware_node" and "physical_node" files for them, but currently
the way it gets to know those handles is not exactly straightforward
(to put it lightly).
This is how it works, roughly:
1. acpi_bus_scan() finds the handle of a PCI root bridge,
creates a struct acpi_device object for it and passes that
object to acpi_pci_root_add().
2. acpi_pci_root_add() creates a struct acpi_pci_root object,
populates its "device" field with its argument's address
(device->handle is the ACPI handle found in step 1).
3. The struct acpi_pci_root object created in step 2 is passed
to pci_acpi_scan_root() and used to get resources that are
passed to pci_create_root_bus().
4. pci_create_root_bus() creates a struct pci_host_bridge object
and passes its "dev" member to device_register().
5. platform_notify(), which for systems with ACPI is set to
acpi_platform_notify(), is called.
So far, so good. Now it starts to be "interesting".
6. acpi_find_bridge_device() is used to find the ACPI handle of
the given device (which is the PCI root bridge) and executes
acpi_pci_find_root_bridge(), among other things, for the
given device object.
7. acpi_pci_find_root_bridge() uses the name (sic!) of the given
device object to extract the segment and bus numbers of the PCI
root bridge and passes them to acpi_get_pci_rootbridge_handle().
8. acpi_get_pci_rootbridge_handle() browses the list of ACPI PCI
root bridges and finds the one that matches the given segment
and bus numbers. Its handle is then used to initialize the
ACPI handle of the PCI root bridge's device object by
acpi_bind_one(). However, this is *exactly* the ACPI handle we
started with in step 1.
Needless to say, this is quite embarassing, but it may be avoided
thanks to commit f3fd0c8 (ACPI: Allow ACPI handles of devices to be
initialized in advance), which makes it possible to initialize the
ACPI handle of a device before passing it to device_register().
Accordingly, add a new __weak routine, pcibios_root_bridge_prepare(),
defaulting to an empty implementation that can be replaced by the
interested architecutres (x86 and ia64 at the moment) with functions
that will set the root bridge's ACPI handle before its dev member is
passed to device_register(). Make both x86 and ia64 provide such
implementations of pcibios_root_bridge_prepare() and remove
acpi_pci_find_root_bridge() and acpi_get_pci_rootbridge_handle() that
aren't necessary any more.
Included is a fix for breakage on systems with non-ACPI PCI host
bridges from Bjorn Helgaas.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-01-09 22:33:37 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-28 16:25:45 -06:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2012-02-23 20:18:59 -07:00
|
|
|
|
2009-11-04 10:32:52 -07:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
2011-10-28 16:25:40 -06:00
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-02-23 20:18:59 -07:00
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2013-01-21 13:20:52 -08:00
|
|
|
|
2009-11-04 10:32:52 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2009-11-04 10:32:52 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2006-06-02 12:35:43 +08:00
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ACPI / PCI: Set root bridge ACPI handle in advance
The ACPI handles of PCI root bridges need to be known to
acpi_bind_one(), so that it can create the appropriate
"firmware_node" and "physical_node" files for them, but currently
the way it gets to know those handles is not exactly straightforward
(to put it lightly).
This is how it works, roughly:
1. acpi_bus_scan() finds the handle of a PCI root bridge,
creates a struct acpi_device object for it and passes that
object to acpi_pci_root_add().
2. acpi_pci_root_add() creates a struct acpi_pci_root object,
populates its "device" field with its argument's address
(device->handle is the ACPI handle found in step 1).
3. The struct acpi_pci_root object created in step 2 is passed
to pci_acpi_scan_root() and used to get resources that are
passed to pci_create_root_bus().
4. pci_create_root_bus() creates a struct pci_host_bridge object
and passes its "dev" member to device_register().
5. platform_notify(), which for systems with ACPI is set to
acpi_platform_notify(), is called.
So far, so good. Now it starts to be "interesting".
6. acpi_find_bridge_device() is used to find the ACPI handle of
the given device (which is the PCI root bridge) and executes
acpi_pci_find_root_bridge(), among other things, for the
given device object.
7. acpi_pci_find_root_bridge() uses the name (sic!) of the given
device object to extract the segment and bus numbers of the PCI
root bridge and passes them to acpi_get_pci_rootbridge_handle().
8. acpi_get_pci_rootbridge_handle() browses the list of ACPI PCI
root bridges and finds the one that matches the given segment
and bus numbers. Its handle is then used to initialize the
ACPI handle of the PCI root bridge's device object by
acpi_bind_one(). However, this is *exactly* the ACPI handle we
started with in step 1.
Needless to say, this is quite embarassing, but it may be avoided
thanks to commit f3fd0c8 (ACPI: Allow ACPI handles of devices to be
initialized in advance), which makes it possible to initialize the
ACPI handle of a device before passing it to device_register().
Accordingly, add a new __weak routine, pcibios_root_bridge_prepare(),
defaulting to an empty implementation that can be replaced by the
interested architecutres (x86 and ia64 at the moment) with functions
that will set the root bridge's ACPI handle before its dev member is
passed to device_register(). Make both x86 and ia64 provide such
implementations of pcibios_root_bridge_prepare() and remove
acpi_pci_find_root_bridge() and acpi_get_pci_rootbridge_handle() that
aren't necessary any more.
Included is a fix for breakage on systems with non-ACPI PCI host
bridges from Bjorn Helgaas.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-01-09 22:33:37 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
2010-02-08 19:16:33 +01:00
|
|
|
|
2011-04-11 11:37:07 +10:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-02-19 03:20:41 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
|
|
|
|
|
2008-10-30 02:17:49 +01:00
|
|
|
|
2007-05-22 22:47:54 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-28 16:25:40 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:19:00 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-28 16:25:40 -06:00
|
|
|
|
|
|
|
|
|
2012-02-23 20:18:59 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-02-23 20:18:59 -07:00
|
|
|
|
2012-04-02 18:31:53 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
2012-05-18 11:35:50 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2011-10-28 16:25:50 -06:00
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
|
|
|
|
|
2011-10-28 16:25:50 -06:00
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-28 16:25:50 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-28 16:25:50 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-28 16:26:05 -06:00
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
2011-10-28 16:26:00 -06:00
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
2011-10-28 16:26:00 -06:00
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
2011-10-28 16:26:00 -06:00
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
2011-10-28 16:26:00 -06:00
|
|
|
|
|
|
|
|
|
2005-09-06 09:31:03 +10:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2012-11-21 15:35:00 -05:00
|
|
|
|
2011-10-28 16:25:55 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
2011-10-28 16:25:55 -06:00
|
|
|
|
|
|
|
|
|
2012-05-17 18:51:12 -07:00
|
|
|
|
2011-10-28 16:25:55 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-01-21 02:08:22 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-10-30 14:31:21 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-10-30 14:31:26 -06:00
|
|
|
|
2012-10-30 14:31:21 -06:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: optionally sort device lists breadth-first
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-29 15:23:23 -05:00
|
|
|
|
2008-08-26 11:00:57 -05:00
|
|
|
|
PCI: optionally sort device lists breadth-first
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-29 15:23:23 -05:00
|
|
|
|
2008-08-26 11:00:57 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI: optionally sort device lists breadth-first
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-29 15:23:23 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-14 14:56:56 -08:00
|
|
|
|
PCI: optionally sort device lists breadth-first
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-29 15:23:23 -05:00
|
|
|
|
2008-08-26 11:00:57 -05:00
|
|
|
|
PCI: optionally sort device lists breadth-first
Problem:
New Dell PowerEdge servers have 2 embedded ethernet ports, which are
labeled NIC1 and NIC2 on the chassis, in the BIOS setup screens, and
in the printed documentation. Assuming no other add-in ethernet ports
in the system, Linux 2.4 kernels name these eth0 and eth1
respectively. Many people have come to expect this naming. Linux 2.6
kernels name these eth1 and eth0 respectively (backwards from
expectations). I also have reports that various Sun and HP servers
have similar behavior.
Root cause:
Linux 2.4 kernels walk the pci_devices list, which happens to be
sorted in breadth-first order (or pcbios_find_device order on i386,
which most often is breadth-first also). 2.6 kernels have both the
pci_devices list and the pci_bus_type.klist_devices list, the latter
is what is walked at driver load time to match the pci_id tables; this
klist happens to be in depth-first order.
On systems where, for physical routing reasons, NIC1 appears on a
lower bus number than NIC2, but NIC2's bridge is discovered first in
the depth-first ordering, NIC2 will be discovered before NIC1. If the
list were sorted breadth-first, NIC1 would be discovered before NIC2.
A PowerEdge 1955 system has the following topology which easily
exhibits the difference between depth-first and breadth-first device
lists.
-[0000:00]-+-00.0 Intel Corporation 5000P Chipset Memory Controller Hub
+-02.0-[0000:03-08]--+-00.0-[0000:04-07]--+-00.0-[0000:05-06]----00.0-[0000:06]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC2, 2.4 kernel name eth1, 2.6 kernel name eth0)
+-1c.0-[0000:01-02]----00.0-[0000:02]----00.0 Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (labeled NIC1, 2.4 kernel name eth0, 2.6 kernel name eth1)
Other factors, such as device driver load order and the presence of
PCI slots at various points in the bus hierarchy further complicate
this problem; I'm not trying to solve those here, just restore the
device order, and thus basic behavior, that 2.4 kernels had.
Solution:
The solution can come in multiple steps.
Suggested fix #1: kernel
Patch below optionally sorts the two device lists into breadth-first
ordering to maintain compatibility with 2.4 kernels. It adds two new
command line options:
pci=bfsort
pci=nobfsort
to force the sort order, or not, as you wish. It also adds DMI checks
for the specific Dell systems which exhibit "backwards" ordering, to
make them "right".
Suggested fix #2: udev rules from userland
Many people also have the expectation that embedded NICs are always
discovered before add-in NICs (which this patch does not try to do).
Using the PCI IRQ Routing Table provided by system BIOS, it's easy to
determine which PCI devices are embedded, or if add-in, which PCI slot
they're in. I'm working on a tool that would allow udev to name
ethernet devices in ascending embedded, slot 1 .. slot N order,
subsort by PCI bus/dev/fn breadth-first. It'll be possible to use it
independent of udev as well for those distributions that don't use
udev in their installers.
Suggested fix #3: system board routing rules
One can constrain the system board layout to put NIC1 ahead of NIC2
regardless of breadth-first or depth-first discovery order. This adds
a significant level of complexity to board routing, and may not be
possible in all instances (witness the above systems from several
major manufacturers). I don't want to encourage this particular train
of thought too far, at the expense of not doing #1 or #2 above.
Feedback appreciated. Patch tested on a Dell PowerEdge 1955 blade
with 2.6.18.
You'll also note I took some liberty and temporarily break the klist
abstraction to simplify and speed up the sort algorithm. I think
that's both safe and appropriate in this instance.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-29 15:23:23 -05:00
|
|
|
|