linux

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directories Now that Linux includes support for the Atmel AT91SAM9260 and AT91SAM9261 processors in addition to the original Atmel AT91RM9200 (with support for more AT91 processors pending), the "mach-at91rm9200" and "arch-at91rm9200" directories should be renamed to indicate their more generic nature. The following git commands should be run BEFORE applying this patch: git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91 git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91 Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-02-05 11:42:07 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 3683/2: ARM: Convert at91rm9200 to generic irq handling Patch from Thomas Gleixner From: Thomas Gleixner <tglx@linutronix.de> Fixup the conversion to generic irq subsystem. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-07-01 23:01:50 +01:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

ARM: at91: Export at91_st_base After commit 5e9cf5e (ARM: at91: make ST (System Timer) soc independent) building at91rm9200_wdt as a module fails with following message ERROR: "at91_st_base" [drivers/watchdog/at91rm9200_wdt.ko] undefined! make[1]: *** [__modpost] Error 1 make: *** [modules] Error 2 Export symbol to allow wdt driver to be built as a module again. Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com> [nicolas.ferre@atmel.com: use EXPORT_SYMBOL_GPL()] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2012-04-04 19:15:15 +02:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

ARM: AT91: Add DT support to AT91RM9200 System Timer Based on AT91 PIT DT patch from Jean-Christophe PLAGNIOL-VILLARD. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

2012-10-28 18:31:07 +00:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 3579/1: AT91RM9200 Timer simplification Patch from Andrew Victor Use a global variable 'last_crtr' to store the time of the last timer tick instead of the ST_RTAR register. It's faster, frees up the ST_RTAR register for other uses, and hopefully makes the code more understandable. [Patch from Peter Menzebach] Also add the SA_TIMER flag to Timer IRQ. (It seems to be required for the realtime preempt patch). Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-06-19 15:23:41 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

ARM: at91: define CLOCK_TICK_RATE to bogus value except A91X40 We have a clocksource which renders CLOCK_TICK_RATE useless. Define it to a bogus value to get rid of some ifdeffery. use local LATCH for at91rm9200 timer but keep it for A91X40 as we do not use a clocksource Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

2011-10-16 18:17:09 +08:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

Initial blind fixup for arm for irq changes Untested, but this should fix up the bulk of the totally mechanical issues, and should make the actual detail fixing easier. Signed-off-by: Linus Torvalds <torvalds@osdl.org>

2006-10-06 10:53:39 -07:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

arm/at91: Don't disable irqs in set_next_event and set_mode callbacks on AT91 the timer irq is shared, so the handler might be entered without irqs being disabled. Though this should not happen as the timer irq is registered early, there have been some reports on the mailing list. To make debugging that problem easier next time it pops up a WARN_ON_ONCE is added to the handler if irqs are not off. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

2009-09-21 09:30:09 +02:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource: Use a plain u64 instead of cycle_t There is no point in having an extra type for extra confusion. u64 is unambiguous. Conversion was done with the following coccinelle script: @rem@ @@ -typedef u64 cycle_t; @fix@ typedef cycle_t; @@ -cycle_t +u64 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>

2016-12-21 20:32:01 +01:00

[ARM] 3580/1: AT91RM9200 Timer suspend/resume support Patch from Andrew Victor Added suspend/resume support for the AT91RM9200 timer. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-06-19 15:26:50 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3580/1: AT91RM9200 Timer suspend/resume support Patch from Andrew Victor Added suspend/resume support for the AT91RM9200 timer. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-06-19 15:26:50 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clockevents/drivers/atmel-st: Migrate to new 'set-state' interface Migrate atmel-st driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now. This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED. Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

2015-06-18 16:24:45 +05:30

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clockevents/drivers/atmel-st: Migrate to new 'set-state' interface Migrate atmel-st driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now. This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED. Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

2015-06-18 16:24:45 +05:30

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

clockevents/drivers/atmel-st: Migrate to new 'set-state' interface Migrate atmel-st driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now. This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED. Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

2015-06-18 16:24:45 +05:30

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

clockevents/drivers/atmel-st: Migrate to new 'set-state' interface Migrate atmel-st driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now. This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED. Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

2015-06-18 16:24:45 +05:30

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clockevents/drivers/atmel-st: Migrate to new 'set-state' interface Migrate atmel-st driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now. This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED. Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

2015-06-18 16:24:45 +05:30

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

clocksource: atmel-st: remove mach/hardware dependency Remove the mach/hardware dependency to prepare the driver for multiplatform support. Also switch from setup_irq() to request_irq() Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-13 11:54:37 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

ARM: AT91: Add DT support to AT91RM9200 System Timer Based on AT91 PIT DT patch from Jean-Christophe PLAGNIOL-VILLARD. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

2012-10-28 18:31:07 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

clocksource: atmel-st: remove mach/hardware dependency Remove the mach/hardware dependency to prepare the driver for multiplatform support. Also switch from setup_irq() to request_irq() Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-13 11:54:37 +01:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 3580/1: AT91RM9200 Timer suspend/resume support Patch from Andrew Victor Added suspend/resume support for the AT91RM9200 timer. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-06-19 15:26:50 +01:00

clocksource: atmel-st: remove mach/hardware dependency Remove the mach/hardware dependency to prepare the driver for multiplatform support. Also switch from setup_irq() to request_irq() Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-13 11:54:37 +01:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource: atmel-st: use syscon/regmap The register range from the system timer is also used by the watchdog driver. Use a regmap to handle concurrent accesses. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:32 +01:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

cpumask: convert struct clock_event_device to cpumask pointers. Impact: change calling convention of existing clock_event APIs struct clock_event_timer's cpumask field gets changed to take pointer, as does the ->broadcast function. Another single-patch change. For safety, we BUG_ON() in clockevents_register_device() if it's not set. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Ingo Molnar <mingo@elte.hu>

2008-12-13 21:20:26 +10:30

clocksource: atmel-st: get and use slow clock The current slow clock rate is hardcoded. Properly get the slow clock and use its rate. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2015-08-16 11:23:44 +02:00

ARM: at91: rm9200: switch back to clockevents_config_and_register The timer code for at91rm9200 was already converted some time ago by Shawn Guo in commit 838a2ae (ARM: use clockevents_config_and_register() where possible) but because of a rounding issue in the timer core this resulted in an easily reproducible oops. So it was reverted (commit b7a8ca5 (ARM: at91: rm9200 fix time support)) which stopped the oops from happening because min_delta_ns is increased by one in arch code which stopped from problem from happening. Now that the timer core problem is fixed (commit a4578ea (clockevents: Sanitize ticks to nsec conversion)), we can switch back to the clockevents_config_and_register helper. Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2013-10-08 16:38:53 +02:00

[ARM] 3240/2: AT91RM9200 support for 2.6 (Core) Patch from SAN People Following changes were made to clock.c: 1) Replaced <asm/hardware/clock.h> with <linux/clk.h> 2) Removed old unused clk_enable & clk_disable. 3) Replaced clk_use/clk_unuse with clk_enable/clk_disable. Otherwise it's the same as the previous patch. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-01-09 17:05:41 +00:00

[ARM] 4539/1: clocksource and clockevents for at91rm9200 GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200. - Oneshot mode (used for NO_HZ and high res timers) uses the alarm to emulate a real oneshot timer; the trickiest bit is how to avoid some lowlevel races. Thanks to Remy Bohmer for various fixes to this code. - Tighten up periodic mode support using the PIT. - Streamline reads of the 32KHz counter. Thanks to Marc Pignat for some testing results: the CRTR register has *very* odd behavior. The reread appears to work around stranger glitches than just getting an old clock value (which would quickly self-correct). - Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100), since that no longer acts correct (time increases too fast). Note that the at91sam9 and at91x40 chips need other solutions, since they don't have the same system timer module. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Bill Gatliff <bgat@billgatliff.com> Acked-by:Remy Bohmer <linux@bohmer.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2007-07-31 01:41:26 +01:00

clocksource/drivers/atmel-st: Convert init function to return error The init functions do not return any error. They behave as the following: - panic, thus leading to a kernel crash while another timer may work and make the system boot up correctly or - print an error and let the caller unaware if the state of the system Change that by converting the init functions to return an error conforming to the CLOCKSOURCE_OF_RET prototype. Proper error handling (rollback, errno value) will be changed later case by case, thus this change just return back an error or success in the init function. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

2016-06-06 19:11:12 +02:00

[ARM] 3580/1: AT91RM9200 Timer suspend/resume support Patch from Andrew Victor Added suspend/resume support for the AT91RM9200 timer. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

2006-06-19 15:26:50 +01:00

clocksource/drivers: Rename CLOCKSOURCE_OF_DECLARE to TIMER_OF_DECLARE The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the clocksource at early stage. However, this macro is also used to initialize the clockevent if any, or the clockevent only. It was originally suggested to declare another macro to initialize a clockevent, so in order to separate the two entities even they belong to the same IP. This was not accepted because of the impact on the DT where splitting a clocksource/clockevent definition does not make sense as it is a Linux concept not a hardware description. On the other side, the clocksource has not interrupt declared while the clockevent has, so it is easy from the driver to know if the description is for a clockevent or a clocksource, IOW it could be implemented at the driver level. So instead of dealing with a named clocksource macro, let's use a more generic one: TIMER_OF_DECLARE. The patch has not functional changes. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Matthias Brugger <matthias.bgg@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

2017-05-26 16:56:11 +02:00

ARM: at91: properly initialize timer Use clocksource_of_init to initialize the system timer instead of relying on a custom function. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

2015-03-12 13:07:30 +01:00

264 lines 6.8 KiB Raw Permalink Normal View History

264 lines

6.8 KiB

Raw Permalink Normal View History