linux

2016-06-25 09:43:58 -03:00

[media] cec: integrate CEC notifier support Support the CEC notifier framework, simplifying drivers that depend on this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-12-13 12:15:57 -02:00

2016-06-25 09:43:58 -03:00

media: media/cec.h: add CEC_CAP_DEFAULTS The CEC_CAP_LOG_ADDRS, CEC_CAP_TRANSMIT, CEC_CAP_PASSTHROUGH and CEC_CAP_RC capabilities are normally always present. Add a CEC_CAP_DEFAULTS define that ORs these four caps to simplify drivers. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-04 06:41:51 -04:00

2016-06-25 09:43:58 -03:00

[media] cec: rename cec_devnode fhs_lock to just lock This lock will be used to protect more than just the fhs list. So rename it to just 'lock'. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-08-02 08:11:00 -03:00

2016-06-25 09:43:58 -03:00

media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:42 -03:00

2016-06-25 09:43:58 -03:00

media: cec: rework the cec event handling Event handling was always fairly simplistic since there were only two events. With the addition of pin events this needed to be redesigned. The state_change and lost_msgs events are now core events with the guarantee that the last state is always available. The new pin events are a queue of events (up to 64 for each event) and the oldest event will be dropped if the application cannot keep up. Lost events are marked with a new event flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:39 -03:00

media: cec: add CEC_EVENT_PIN_HPD_LOW/HIGH events Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH. This is specifically meant for use with the upcoming cec-gpio driver and makes it possible to trace when the HPD pin changes. Some HDMI sinks do strange things with the HPD and this makes it easy to debug this. Note that this also moves the initialization of a devnode mutex and list to the allocate_adapter function: if the HPD is high, then as soon as the HPD interrupt is created an interrupt occurs and cec_queue_pin_hpd_event() is called which requires that the devnode mutex and list are initialized. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-15 10:07:25 -04:00

2016-06-25 09:43:58 -03:00

media: cec: rework the cec event handling Event handling was always fairly simplistic since there were only two events. With the addition of pin events this needed to be redesigned. The state_change and lost_msgs events are now core events with the guarantee that the last state is always available. The new pin events are a queue of events (up to 64 for each event) and the oldest event will be dropped if the application cannot keep up. Lost events are marked with a new event flag. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:39 -03:00

2016-06-25 09:43:58 -03:00

media: cec: add the adap_monitor_pin_enable op Some devices can monitor the CEC pin using an interrupt, but you only want to enable the interrupt if you actually switch to pin monitoring mode. So add a new op that is called when pin monitoring needs to be switched on or off. Also fix a small bug where the initial CEC pin event was sent again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN mode. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-11-05 07:36:36 -05:00

2016-06-25 09:43:58 -03:00

media: cec: add adap_free op This is needed for CEC adapters that allocate resources that have to be freed before the cec_adapter is deleted. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:36 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: limit the size of the transmit queue The size of the transmit queue was unlimited, which meant that in non-blocking mode you could flood the CEC adapter with messages to be transmitted. Limit this to 18 messages. Also print the number of pending transmits and the timeout value in the status debugfs file. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-07-17 11:40:05 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: limit the size of the transmit queue The size of the transmit queue was unlimited, which meant that in non-blocking mode you could flood the CEC adapter with messages to be transmitted. Limit this to 18 messages. Also print the number of pending transmits and the timeout value in the status debugfs file. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-07-17 11:40:05 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: limit the size of the transmit queue The size of the transmit queue was unlimited, which meant that in non-blocking mode you could flood the CEC adapter with messages to be transmitted. Limit this to 18 messages. Also print the number of pending transmits and the timeout value in the status debugfs file. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-07-17 11:40:05 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: add CEC_CAP_NEEDS_HPD Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set then the hardware can only use CEC if the HDMI Hotplug Detect pin is high. Such hardware cannot handle the corner case in the CEC specification where it is possible to transmit messages even if no hotplug signal is present (needed for some displays that turn off the HPD when in standby, but still have CEC enabled). Typically hardware that needs this capability have the HPD wired to the CEC block, often to a 'power' or 'active' pin. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-07 11:46:12 -03:00

2016-06-25 09:43:58 -03:00

media: cec: replace pin->cur_value by adap->cec_pin_is_high The current CEC pin value (0 or 1) was part of the cec_pin struct, but that assumes that CEC pin monitoring can only be used with a driver that uses the low-level CEC pin framework. But hardware that has both a high-level API and can monitor the CEC pin at low-level at the same time does not need to depend on the cec pin framework. To support such devices remove the cur_value field from struct cec_pin and add a cec_pin_is_high field to cec_adapter. This also makes it possible to drop the '#ifdef CONFIG_CEC_PIN' in cec-api.c. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-20 06:53:10 -04:00

2016-06-25 09:43:58 -03:00

media: cec: add core support for low-level CEC pin monitoring Add support for the new MONITOR_PIN mode. Add the cec_pin_event function that the CEC pin code will call to queue pin change events. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:41 -03:00

2016-06-25 09:43:58 -03:00

media: cec: improve transmit timeout logging Kernel logging messes up the upcoming low-level CEC monitoring support which is very time-sensitive. So change the debug level of this message but keep a counter that is shown in the debugfs status log. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:34 -03:00

[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER This config option is strictly speaking independent of the media subsystem since it can be used by drm as well. Besides, it looks odd when drivers select CEC_CORE and MEDIA_CEC_NOTIFIER, that's inconsistent naming. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-05-28 05:58:04 -03:00

[media] cec: integrate CEC notifier support Support the CEC notifier framework, simplifying drivers that depend on this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-12-13 12:15:57 -02:00

media: cec-pin: add low-level pin hardware support Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:42 -03:00

[media] cec: integrate CEC notifier support Support the CEC notifier framework, simplifying drivers that depend on this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-12-13 12:15:57 -02:00

2016-06-25 09:43:58 -03:00

media: rc-core: rename input_name to device_name When an ir-spi is registered, you get this message. rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0 "Unspecified device" refers to input_name, which makes no sense for IR TX only devices. So, rename to device_name. Also make driver_name const char* so that no casts are needed anywhere. Now ir-spi reports: rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0 Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-01 12:13:19 -04:00

2016-06-25 09:43:58 -03:00

[media] cec: Add cec_get_drvdata() Add a helper function to get driver private data from CEC adapter. This helps the readability a little bit and allows to change the 'priv' field name to something else without needing to touch all drivers. Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-03-24 13:47:52 -03:00

2016-06-25 09:43:58 -03:00

media: cec: disable the hardware when unregistered When the device is being unregistered disable the hardware, don't wait until cec_delete_adapter is called as the hardware may have disappeared by then. This would be the case for hotplugable devices. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reported-by: Bård Eirik Winther <bwinther@cisco.com> Tested-by: Bård Eirik Winther <bwinther@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-11-22 04:12:39 -05:00

[media] cec.h: merge cec-edid.h into cec.h Drop the separate cec-edid.h header and merge it into cec.h. There was really no need to have a separate header for this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-04-17 07:54:37 -03:00

[media] cec: add cec_s_phys_addr_from_edid helper function This function simplifies the integration of CEC in DRM drivers. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-07 11:46:08 -03:00

[media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED Fix messages like this: adv7842.c:(.text+0x2edadd): undefined reference to `cec_unregister_adapter' when CEC_CORE=m but the driver including media/cec.h is built-in. In that case the static inlines provided in media/cec.h should be used by that driver. Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-08 15:37:44 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: pass parent device in register(), not allocate() The cec_allocate_adapter function doesn't need the parent device, only the cec_register_adapter function needs it. Drop the cec_devnode parent field, since devnode.dev.parent can be used instead. This change makes the framework consistent with other frameworks where the parent device is not used until the device is registered. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-11-25 06:23:34 -02:00

2016-06-25 09:43:58 -03:00

[media] cec: add cec_s_phys_addr_from_edid helper function This function simplifies the integration of CEC in DRM drivers. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-07 11:46:08 -03:00

2016-06-25 09:43:58 -03:00

media: cec: add *_ts variants for transmit_done/received_msg Currently the transmit_(attempt_)done and received_msg functions set the timestamp themselves. For the upcoming low-level pin API we need to pass this as an argument instead. So make _ts variants that allow the caller to specify the timestamp. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:35 -03:00

[media] cec: add cec_transmit_attempt_done helper function A simpler variant of cec_transmit_done to be used where the HW does just a single attempt at a transmit. So if the status indicates an error, then the corresponding error count will always be 1 and this function figures that out based on the status argument. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-07 11:46:10 -03:00

media: cec: add *_ts variants for transmit_done/received_msg Currently the transmit_(attempt_)done and received_msg functions set the timestamp themselves. For the upcoming low-level pin API we need to pass this as an argument instead. So make _ts variants that allow the caller to specify the timestamp. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:35 -03:00

2016-06-25 09:43:58 -03:00

media: cec: add core support for low-level CEC pin monitoring Add support for the new MONITOR_PIN mode. Add the cec_pin_event function that the CEC pin code will call to queue pin change events. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:41 -03:00

media: cec: rename pin events/function The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function did not specify that these were about CEC pin events. Since in the future there will also be HPD pin events it is wise to rename the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and cec_queue_pin_cec_event() now before these become part of the ABI. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-15 15:26:25 -04:00

media: cec: add core support for low-level CEC pin monitoring Add support for the new MONITOR_PIN mode. Add the cec_pin_event function that the CEC pin code will call to queue pin change events. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:41 -03:00

media: cec: rename pin events/function The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function did not specify that these were about CEC pin events. Since in the future there will also be HPD pin events it is wise to rename the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and cec_queue_pin_cec_event() now before these become part of the ABI. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-15 15:26:25 -04:00

media: cec: add core support for low-level CEC pin monitoring Add support for the new MONITOR_PIN mode. Add the cec_pin_event function that the CEC pin code will call to queue pin change events. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:41 -03:00

media: cec: rename pin events/function The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function did not specify that these were about CEC pin events. Since in the future there will also be HPD pin events it is wise to rename the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and cec_queue_pin_cec_event() now before these become part of the ABI. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-15 15:26:25 -04:00

media: cec: add core support for low-level CEC pin monitoring Add support for the new MONITOR_PIN mode. Add the cec_pin_event function that the CEC pin code will call to queue pin change events. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-07-11 03:30:41 -03:00

media: cec: add CEC_EVENT_PIN_HPD_LOW/HIGH events Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH. This is specifically meant for use with the upcoming cec-gpio driver and makes it possible to trace when the HPD pin changes. Some HDMI sinks do strange things with the HPD and this makes it easy to debug this. Note that this also moves the initialization of a devnode mutex and list to the allocate_adapter function: if the HPD is high, then as soon as the HPD interrupt is created an interrupt occurs and cec_queue_pin_hpd_event() is called which requires that the devnode mutex and list are initialized. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-15 10:07:25 -04:00

[media] cec.h: merge cec-edid.h into cec.h Drop the separate cec-edid.h header and merge it into cec.h. There was really no need to have a separate header for this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-04-17 07:54:37 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: pass parent device in register(), not allocate() The cec_allocate_adapter function doesn't need the parent device, only the cec_register_adapter function needs it. Drop the cec_devnode parent field, since devnode.dev.parent can be used instead. This change makes the framework consistent with other frameworks where the parent device is not used until the device is registered. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2016-11-25 06:23:34 -02:00

2016-06-25 09:43:58 -03:00

[media] cec: add cec_s_phys_addr_from_edid helper function This function simplifies the integration of CEC in DRM drivers. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-07 11:46:08 -03:00

[media] cec.h: merge cec-edid.h into cec.h Drop the separate cec-edid.h header and merge it into cec.h. There was really no need to have a separate header for this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-04-17 07:54:37 -03:00

media: cec.h: initialize *parent and *port in cec_phys_addr_validate Make sure these values are set to avoid 'uninitialized variable' warnings. Hasn't happened yet, but better safe than sorry. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-08-31 04:12:53 -04:00

[media] cec.h: merge cec-edid.h into cec.h Drop the separate cec-edid.h header and merge it into cec.h. There was really no need to have a separate header for this. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-04-17 07:54:37 -03:00

2016-06-25 09:43:58 -03:00

[media] cec: add cec_phys_addr_invalidate() helper function Simplifies setting the physical address to CEC_PHYS_ADDR_INVALID. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

2017-06-07 11:46:09 -03:00

2016-06-25 09:43:58 -03:00

460 lines 12 KiB Raw Permalink Normal View History

460 lines

12 KiB

Raw Permalink Normal View History