linux

mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ synced 2026-11-08 18:57:22 +00:00

73 lines

1.7 KiB

Raw Permalink Normal View History

pwm: Add support for Xilinx AXI Timer This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly found on Xilinx FPGAs. At the moment clock control is very basic: we just enable the clock during probe and pin the frequency. In the future, someone could add support for disabling the clock when not in use. Some common code has been specially demarcated. While currently only used by the PWM driver, it is anticipated that it may be split off in the future to be used by the timer driver as well. This driver was written with reference to Xilinx DS764 for v1.03.a [1]. [1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf Signed-off-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> 2022-03-03 17:35:43 -05:00










































pwm: xilinx: Fix u32 overflow issue in 32-bit width PWM mode. This timer HW supports 8, 16 and 32-bit timer widths. This driver currently uses a u32 to store the max possible value of the timer. However, statements perform addition of 2 in xilinx_pwm_apply() when calculating the period_cycles and duty_cycles values. Since priv->max is a u32, this will result in an overflow to 1 which will not only be incorrect but fail on range comparison. This results in making it impossible to set the PWM in this timer mode. There are two obvious solutions to the current problem: 1. Cast each instance where overflow occurs to u64. 2. Change priv->max from a u32 to a u64. Solution #1 requires more code modifications, and leaves opportunity to introduce similar overflows if other math statements are added in the future. These may also go undetected if running in non 32-bit timer modes. Solution #2 is the much smaller and cleaner approach and thus the chosen method in this patch. This was tested on a Zynq UltraScale+ with multiple instances of the PWM IP. Signed-off-by: Ken Sloat <ksloat@designlinxhs.com> Reviewed-by: Michal Simek <michal.simek@amd.com> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Link: https://lore.kernel.org/r/SJ0P222MB0107490C5371B848EF04351CA1E19@SJ0P222MB0107.NAMP222.PROD.OUTLOOK.COM Signed-off-by: Michal Simek <michal.simek@amd.com> 2022-12-15 16:07:15 +00:00
pwm: Add support for Xilinx AXI Timer This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly found on Xilinx FPGAs. At the moment clock control is very basic: we just enable the clock during probe and pin the frequency. In the future, someone could add support for disabling the clock when not in use. Some common code has been specially demarcated. While currently only used by the PWM driver, it is anticipated that it may be split off in the future to be used by the timer driver as well. This driver was written with reference to Xilinx DS764 for v1.03.a [1]. [1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf Signed-off-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> 2022-03-03 17:35:43 -05:00

73 lines 1.7 KiB Raw Permalink Normal View History

73 lines

1.7 KiB

Raw Permalink Normal View History