linux/drivers/soundwire/intel.c

1096 lines
28 KiB

soundwire: intel: don't save hw_params for use in prepare The existing code copies the hw_params pointer and reuses it later in .prepare, specifically to re-initialize the ALH DMA channel information that's lost in suspend-resume cycles. This is not needed, we can directly access the information from the substream/rtd - as done for the HDAudio DAIs in sound/soc/sof/intel/hda-dai.c In addition, using the saved pointer causes the suspend-resume test cases to fail on specific platforms, depending on which version of GCC is used. Péter Ujfalusi and I have spent long hours to root-cause this problem that was reported by the Intel CI first with 6.2-rc1 and again v6.3-rc1. In the latter case we were lucky that the problem was 100% reproducible on local test devices, and found out that adding a dev_dbg() or adding a call to usleep_range() just before accessing the saved pointer "fixed" the issue. With errors appearing just by changing the compiler version or minor changes in the code generated, clearly we have a memory management Heisenbug. The root-cause seems to be that the hw_params pointer is not persistent. The soc-pcm code allocates the hw_params structure on the stack, and passes it to the BE dailink hw_params and DAIs hw_params. Saving such a pointer and reusing it later during the .prepare stage cannot possibly work reliably, it's broken-by-design since v5.10. It's astonishing that the problem was not seen earlier. This simple fix will have to be back-ported to -stable, due to changes to avoid the use of the get/set_dmadata routines this patch will only apply on kernels older than v6.1. Fixes: a5a0239c27fe ("soundwire: intel: reinitialize IP+DSP in .prepare(), but only when resuming") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20230321022642.1426611-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-03-21 10:26:42 +08:00
soundwire: intel: don't save hw_params for use in prepare The existing code copies the hw_params pointer and reuses it later in .prepare, specifically to re-initialize the ALH DMA channel information that's lost in suspend-resume cycles. This is not needed, we can directly access the information from the substream/rtd - as done for the HDAudio DAIs in sound/soc/sof/intel/hda-dai.c In addition, using the saved pointer causes the suspend-resume test cases to fail on specific platforms, depending on which version of GCC is used. Péter Ujfalusi and I have spent long hours to root-cause this problem that was reported by the Intel CI first with 6.2-rc1 and again v6.3-rc1. In the latter case we were lucky that the problem was 100% reproducible on local test devices, and found out that adding a dev_dbg() or adding a call to usleep_range() just before accessing the saved pointer "fixed" the issue. With errors appearing just by changing the compiler version or minor changes in the code generated, clearly we have a memory management Heisenbug. The root-cause seems to be that the hw_params pointer is not persistent. The soc-pcm code allocates the hw_params structure on the stack, and passes it to the BE dailink hw_params and DAIs hw_params. Saving such a pointer and reusing it later during the .prepare stage cannot possibly work reliably, it's broken-by-design since v5.10. It's astonishing that the problem was not seen earlier. This simple fix will have to be back-ported to -stable, due to changes to avoid the use of the get/set_dmadata routines this patch will only apply on kernels older than v6.1. Fixes: a5a0239c27fe ("soundwire: intel: reinitialize IP+DSP in .prepare(), but only when resuming") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20230321022642.1426611-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-03-21 10:26:42 +08:00
soundwire: intel: don't save hw_params for use in prepare The existing code copies the hw_params pointer and reuses it later in .prepare, specifically to re-initialize the ALH DMA channel information that's lost in suspend-resume cycles. This is not needed, we can directly access the information from the substream/rtd - as done for the HDAudio DAIs in sound/soc/sof/intel/hda-dai.c In addition, using the saved pointer causes the suspend-resume test cases to fail on specific platforms, depending on which version of GCC is used. Péter Ujfalusi and I have spent long hours to root-cause this problem that was reported by the Intel CI first with 6.2-rc1 and again v6.3-rc1. In the latter case we were lucky that the problem was 100% reproducible on local test devices, and found out that adding a dev_dbg() or adding a call to usleep_range() just before accessing the saved pointer "fixed" the issue. With errors appearing just by changing the compiler version or minor changes in the code generated, clearly we have a memory management Heisenbug. The root-cause seems to be that the hw_params pointer is not persistent. The soc-pcm code allocates the hw_params structure on the stack, and passes it to the BE dailink hw_params and DAIs hw_params. Saving such a pointer and reusing it later during the .prepare stage cannot possibly work reliably, it's broken-by-design since v5.10. It's astonishing that the problem was not seen earlier. This simple fix will have to be back-ported to -stable, due to changes to avoid the use of the get/set_dmadata routines this patch will only apply on kernels older than v6.1. Fixes: a5a0239c27fe ("soundwire: intel: reinitialize IP+DSP in .prepare(), but only when resuming") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20230321022642.1426611-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2023-03-21 10:26:42 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: use pm_runtime_resume() on component probe During the card registration, transactions on the SoundWire bus can be initiated. If the ALSA card is registered after the bus suspends, timeouts can be seen while reading/writing codec registers. This is extremely easy to reproduce in driver bind/unbind tests. In an initial experiment, the ASoC soc-component.c code was modified to initiate a pm_runtime resume on a component probe. The results showed this was too invasive. Instead this patch suggests resuming the SoundWire component only. Because of the parent-child hierarchy enforced by the pm_runtime framework, it can be argued that the codec component probe should be enough to resume all necessary devices, and indeed the same resume will be applied to SoundWire codecs used on Intel platforms. Calling pm_runtime_resume() on both the Intel and codec sides has the benefit of resuming the bus without assuming any order during the card registration. The first component on a dailink to be probed will resume the bus. In addition, if a codec driver did not implement this transition, the Intel component would still resume the bus and avoid timeouts on card registration. BugLink: https://github.com/thesofproject/linux/issues/3651 Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220621225641.221170-4-pierre-louis.bossart@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-06-21 17:56:40 -05:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
soundwire: intel: improve suspend flows This patch provides both a simplification of the suspend flows and a better balanced operation during suspend/resume transition, as part of the transition of Sound Open Firmware (SOF) to dynamic pipelines: the DSP resources are only enabled when required instead of enabled on startup. The exiting code relies on a convoluted way of dealing with suspend signals. Since there is no .suspend DAI callback, we used the component .suspend and marked all the component DAI dmas as 'suspended'. The information was used in the .prepare stage to differentiate resume operations from xrun handling, and only reinitialize SHIM registers and DMA in the former case. While this solution has been working reliably for about 2 years, there is a much better solution consisting in trapping the TRIGGER_SUSPEND in the .trigger DAI ops. The DMA is still marked in the same way for the .prepare op to run, but in addition the callbacks sent to DSP firmware are now balanced. Normal operation: hw_params -> intel_params_stream hw_free -> intel_free_stream suspend -> intel_free_stream prepare -> intel_params_stream This balanced operation was not required with existing SOF firmware relying on static pipelines instantiated at every boot. With the on-going transition to dynamic pipelines, it's however a requirement to keep the use count for the DAI widget balanced across all transitions. The component suspend is not removed but instead modified to deal with a corner case: when a substream is PAUSED, the ALSA core does not throw the TRIGGER_SUSPEND. This is problematic since the refcount for all pipelines and widgets is not balanced, leading to issues on resume. The trigger callback keeps track of the 'paused' state with a new flag, which is tested during the component suspend called later to release the remaining DSP resources. These resources will be re-enabled in the .prepare step. The IPC used in the TRIGGER_SUSPEND to release DSP resources is not a problem since the BE dailink is already marked as non-atomic. Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-4-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:30 +08:00
ASoC/SoundWire: dai: expand 'stream' concept beyond SoundWire The HDAudio ASoC support relies on the set_tdm_slots() helper to store the HDaudio stream tag in the tx_mask. This only works because of the pre-existing order in soc-pcm.c, where the hw_params() is handled for codec_dais *before* cpu_dais. When the order is reversed, the stream_tag is used as a mask in the codec fixup functions: /* fixup params based on TDM slot masks */ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK && codec_dai->tx_mask) soc_pcm_codec_params_fixup(&codec_params, codec_dai->tx_mask); As a result of this confusion, the codec_params_fixup() ends-up generating bad channel masks, depending on what stream_tag was allocated. We could add a flag to state that the tx_mask is really not a mask, but it would be quite ugly to persist in overloading concepts. Instead, this patch suggests a more generic get/set 'stream' API based on the existing model for SoundWire. We can expand the concept to store 'stream' opaque information that is specific to different DAI types. In the case of HDAudio DAIs, we only need to store a stream tag as an unsigned char pointer. The TDM rx_ and tx_masks should really only be used to store masks. Rename get_sdw_stream/set_sdw_stream callbacks and helpers as get_stream/set_stream. No functionality change beyond the rename. Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Acked-By: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-24 10:10:31 +08:00
sound updates for 6.0-rc1 As diffstat shows, we've had lots of developments in a wide range at this time; the majority of changes are about ASoC, including subsystem-wide cleanups, continued SOF / Intel updates and a bunch of new drivers (as usual), while there have been some significant (but almost invisible) improvements in ALSA core side, too. Below are some highlights: Core: - Faster lookups of control elements with Xarray; normal user won't notice, but on the devices with tons of control elements, it can be visibly faster - Support for input validation for controls; this will harden for badly written drivers in general with a slight overhead - Deferred async signal handling for working around the potential deadlocks - Cleanup / refactoring raw MIDI locking code ASoC: - Restructing of the set_fmt() callbacks for making things clearer in situations like CODEC to CODEC links - Clean up and modernizing the DAI naming scheme setups - Merge of more of the Intel AVS driver stack, including some board integrations - New version 4 mechanism for communication with SOF DSPs - Suppoort for dynamically selecting the PLL to use at runtime on i.MX platforms - Improvements for CODEC to CODEC support in the generic cards - Support for AMD Jadeite and various machines, AMD RPL, Intel MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments TAS2780 HD- and USB-audio: - Continued improvement for CS35L41 (sub)codec support - More quirks for various devices (HP, Lenovo, Dell, Clevo) -----BEGIN PGP SIGNATURE----- iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmLr5bcOHHRpd2FpQHN1 c2UuZGUACgkQLtJE4w1nLE93IQ/+OleeiGv7C487QN5MrBCkdFnSAiXsXDArcMgo Gt6XLubH54et1tqi2ms4gRQOqr4HiBelERuqmaCLMZfEgVDc0VhJnf2jjhluYq9+ o9+kcYKul6qTZeNZLPjEX8pBvDe7HzOl7yep++ZnKeH6DAKNQQLDjVuOcQU/BXdY kL8vYrLI3zfqj/pCePb5xpkBx4XdCrE3TfiCr3tAHVg9MyvSGOJyWs02mEBqQRnc rlLmkjQVQyln/AGK4RAPMmrrFytktAvBjmIDyFL7kAzhdxe0ouNzTvdxESeojNJv CVo/p3hl/+0LYjpD2x9v2pQuifOfpjwSCy6f8jsaF366sMwR1D45h051prILsxAF 05D5AOwMCnnJdFQFxw3mIkoDva3/PRX8GFfHsXoz+efc5Ibp8ksNYVgAJ3D2TTtt 7nAYMn0dimVDtw2LHiKantgWAs/rOqD3hDzGxFj2sR662ahsHr8pT8csnJAGoBvW 7kgx7ZzFo/wSyZJqVqV7p4g6J79ScehRwhqoiwZau9Eo+PhuxZUKvm4RwGFh0Vvg GbiVRPfLV4xQd/pDin6qRX1M7cgPc62qGLkhQHAzrX6H5ipwIbQrpyDGLjwdSEp8 XcQmzCG1zGOvb9A8BY1VBOQXxZRTqN58XujbZ6hsms7Uw8sqagxpYLA/e1bvt1E1 RQoHQRw= =1n0/ -----END PGP SIGNATURE----- Merge tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound updates from Takashi Iwai: "As the diffstat shows, we've had lots of developments in a wide range at this time; the majority of changes are about ASoC, including subsystem-wide cleanups, continued SOF / Intel updates and a bunch of new drivers (as usual), while there have been some significant (but almost invisible) improvements in ALSA core side, too. Below are some highlights: Core: - Faster lookups of control elements with Xarray; normal user won't notice, but on the devices with tons of control elements, it can be visibly faster - Support for input validation for controls; this will harden for badly written drivers in general with a slight overhead - Deferred async signal handling for working around the potential deadlocks - Cleanup / refactoring raw MIDI locking code ASoC: - Restructing of the set_fmt() callbacks for making things clearer in situations like CODEC to CODEC links - Clean up and modernizing the DAI naming scheme setups - Merge of more of the Intel AVS driver stack, including some board integrations - New version 4 mechanism for communication with SOF DSPs - Suppoort for dynamically selecting the PLL to use at runtime on i.MX platforms - Improvements for CODEC to CODEC support in the generic cards - Support for AMD Jadeite and various machines, AMD RPL, Intel MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments TAS2780 HD- and USB-audio: - Continued improvement for CS35L41 (sub)codec support - More quirks for various devices (HP, Lenovo, Dell, Clevo)" * tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits) ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx ALSA: line6: Replace sprintf() with sysfs_emit() ALSA: hda: Replace sprintf() with sysfs_emit() ALSA: pcm: Replace sprintf() with sysfs_emit() ALSA: core: Replace scnprintf() with sysfs_emit() ALSA: control-led: Replace sprintf() with sysfs_emit() ALSA: aoa: Replace sprintf() with sysfs_emit() ALSA: ac97: Replace sprintf() with sysfs_emit() ALSA: hda/realtek: Add quirk for Clevo NV45PZ ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7 ALSA: control: Use deferred fasync helper ALSA: pcm: Use deferred fasync helper ALSA: timer: Use deferred fasync helper ALSA: core: Add async signal helpers ASoC: q6asm: use kcalloc() instead of kzalloc() ACPI: scan: Add CLSA0101 Laptop Support ALSA: hda: cs35l41: Support CLSA0101 ALSA: hda: cs35l41: Use the CS35L41 HDA internal define ASoC: dt-bindings: use spi-peripheral-props.yaml ASoC: codecs: va-macro: use fsgen as clock ...
2022-08-06 10:19:51 -07:00