linux/drivers/thunderbolt/Kconfig

78 lines
2.6 KiB

thunderbolt, efi: Fix Kconfig dependencies harder Since commit c9cc3aaa0281 ("thunderbolt: Use Device ROM retrieved from EFI"), the THUNDERBOLT config option selects APPLE_PROPERTIES. This broke the build for certain configs because APPLE_PROPERTIES is located in a menu which depends on EFI: If EFI is not enabled, the prerequisites needed for APPLE_PROPERTIES are not selected: Those are EFI_DEV_PATH_PARSER and UCS2_STRING. Additionally EFI_DEV_PATH_PARSER won't compile unless ACPI is enabled. Commit 79f9cd35b05e ("thunderbolt, efi: Fix Kconfig dependencies") sought to fix the breakage by making THUNDERBOLT select APPLE_PROPERTIES only if EFI_STUB is enabled. On x86, EFI_STUB depends on EFI and EFI depends on ACPI, so this fixed the build at least on this architecture. However on arm and arm64, EFI_STUB does not depend on EFI, so once again the prerequisites needed for APPLE_PROPERTIES are not selected. Additionally ACPI is not available on arm and optional on arm64, therefore EFI_DEV_PATH_PARSER won't compile. Fix by selecting APPLE_PROPERTIES only on x86. Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Cc: Andreas Noever <andreas.noever@gmail.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/5c241cf92eb1dc2421218c1204c6a9d22c9f847b.1479456179.git.lukas@wunner.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-11-18 09:22:59 +01:00
thunderbolt: Add support for host and device NVM firmware upgrade Starting from Intel Falcon Ridge the NVM firmware can be upgraded by using DMA configuration based mailbox commands. If we detect that the host or device (device support starts from Intel Alpine Ridge) has the DMA configuration based mailbox we expose NVM information to the userspace as two separate Linux NVMem devices: nvm_active and nvm_non_active. The former is read-only portion of the active NVM which firmware upgrade tools can be use to find out suitable NVM image if the device identification strings are not enough. The latter is write-only portion where the new NVM image is to be written by the userspace. It is up to the userspace to find out right NVM image (the kernel does very minimal validation). The ICM firmware itself authenticates the new NVM firmware and fails the operation if it is not what is expected. We also expose two new sysfs files per each switch: nvm_version and nvm_authenticate which can be used to read the active NVM version and start the upgrade process. We also introduce safe mode which is the mode a switch goes when it does not have properly authenticated firmware. In this mode the switch only accepts a couple of commands including flashing a new NVM firmware image and triggering power cycle. This code is based on the work done by Amir Levy and Michael Jamet. Signed-off-by: Michael Jamet <michael.jamet@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-06 15:25:17 +03:00
thunderbolt: Add debugfs interface This adds debugfs interface that can be used for debugging possible issues in hardware/software. It exposes router and adapter config spaces through files like this: /sys/kernel/debug/thunderbolt/<DEVICE>/regs /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters ... The "regs" is either the router or port configuration space register dump. The "path" is the port path configuration space and "counters" is the optional counters configuration space. These files contains one register per line so it should be easy to use normal filtering tools to find the registers of interest if needed. The router and adapter regs file becomes writable when CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done in production systems) and in this case the developer can write "offset value" lines there to modify the hardware directly. For convenience this also supports the long format the read side produces (but ignores the additional fields). The counters file can be written even when CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear the counter values. Signed-off-by: Gil Fine <gil.fine@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-29 20:30:52 +03:00
thunderbolt: Add debugfs interface This adds debugfs interface that can be used for debugging possible issues in hardware/software. It exposes router and adapter config spaces through files like this: /sys/kernel/debug/thunderbolt/<DEVICE>/regs /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path /sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters ... The "regs" is either the router or port configuration space register dump. The "path" is the port path configuration space and "counters" is the optional counters configuration space. These files contains one register per line so it should be easy to use normal filtering tools to find the registers of interest if needed. The router and adapter regs file becomes writable when CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done in production systems) and in this case the developer can write "offset value" lines there to modify the hardware directly. For convenience this also supports the long format the read side produces (but ignores the additional fields). The counters file can be written even when CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear the counter values. Signed-off-by: Gil Fine <gil.fine@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-29 20:30:52 +03:00
thunderbolt: Add DMA traffic test driver This driver allows sending DMA traffic over XDomain connection. Specifically over a loopback connection using either a Thunderbolt/USB4 cable that is connected back to the host router port, or a special loopback dongle that has RX and TX lines crossed. This can be useful at manufacturing floor to check whether Thunderbolt/USB4 ports are functional. The driver exposes debugfs directory under the XDomain service that can be used to configure the driver, start the test and check the results. If a loopback dongle is used the steps to send and receive 1000 packets can be done like: # modprobe thunderbolt_dma_test # echo 1000 > /sys/kernel/debug/thunderbolt/<service_id>/dma_test/packets_to_receive # echo 1000 > /sys/kernel/debug/thunderbolt/<service_id>/dma_test/packets_to_send # echo 1 > /sys/kernel/debug/thunderbolt/<service_id>/dma_test/test # cat /sys/kernel/debug/thunderbolt/<service_id>/dma_test/status When a cable is connected back to host then there are two Thunderbolt services, one is configured for receiving (does not matter which one): # modprobe thunderbolt_dma_test # echo 1000 > /sys/kernel/debug/thunderbolt/<service_a>/dma_test/packets_to_receive # echo 1 > /sys/kernel/debug/thunderbolt/<service_a>/dma_test/test The other one for sending: # echo 1000 > /sys/kernel/debug/thunderbolt/<service_b>/dma_test/packets_to_send # echo 1 > /sys/kernel/debug/thunderbolt/<service_b>/dma_test/test Results can be read from both services status attributes. Signed-off-by: Isaac Hazan <isaac.hazan@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-24 11:44:02 +03:00
thunderbolt: Add support for USB4STREAM Introduce USB4STREAM protocol and Linux implementation. This allows two (or more) hosts to transfer data directly over Thunderbolt/USB4 cable through a character device without need to go through the network stack. Any application that supports read(2) and write(2) in some form should be able to use the device without changes. The data is sent out to the other side over a tunnel inside Thunderbolt/USB4 fabric. The character device is called /dev/tbstreamX where X is the minor number starting from 0. All stream devices need to be configured first. This is done through ConfigFS interface. There can be multiple streams at the same time (this depends on number of DMA rings and available HopIDs) and a single stream supports traffic in both directions. For example there could be an application that uses one stream as control channel and another one as bi-directional data channel. A real use-case for this is to take a backup as a part of recovery initramfs tooling (no need to setup networking or have ssh or similar tooling as part of the initramfs). Say we want to backup the disk of host1 to host2. First Thunderbolt/USB4 cable is connected between the hosts (there can be devices in the middle too) then the receiving side configures the stream: host2 # mkdir /sys/kernel/config/thunderbolt/stream/0-1.0 host2 # mkdir /sys/kernel/config/thunderbolt/stream/0-1.0/backup host2 # echo -1 > /sys/kernel/config/thunderbolt/stream/0-1.0/backup/in_hopid host2 # echo -1 > /sys/kernel/config/thunderbolt/stream/0-1.0/backup/out_hopid We use automatic HopID allocation (writing -1 to HopIDs) for simplicity. From this point forward the /dev/tbstream0 can be used pretty much as regular file: host2 # dd if=/dev/tbstream0 of=/tmp/host1.nvme0n1.backup-$(date +%F) bs=256k The host that is being backed up then configures the stream accordingly: host1 # mkdir /sys/kernel/config/thunderbolt/stream/0-503.0 host1 # mkdir /sys/kernel/config/thunderbolt/stream/0-503.0/backup Here we take advantage of the fact that host2 also announces the active streams through XDomain properties so the name "backup" gives us the HopIDs. It is also possible to configure them manually in the same way we did for host2. Then it is just a matter of copying the data over: host1 # dd if=/dev/nvme0n1 of=/dev/tbstream0 bs=256k Similarly it is possible to transfer parts of the filesystem. For example copy contents of mydir over to the host2: host2 # gunzip < /dev/tbstream0 | tar xf - host1 # tar cf - mydir | gzip > /dev/tbstream0 Other end of the spectrum use-case is "borrowing" laptop (host1) camera to desktop (host2): host2 # gst-launch-1.0 filesrc location=/dev/tbstream0 ! jpegdec ! videoconvert ! \ autovideosink host1 # gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-raw,width=1920,height=1080 ! \ jpegenc quality=90 ! filesink location=/dev/tbstream0 Once the streams are no longer needed they can be removed: host1 # cd /sys/kernel/config/thunderbolt/stream/ host1 # rmdir -p 0-503.0/backup host2 # cd /sys/kernel/config/thunderbolt/stream host2 # rmdir -p 0-1.0/backup Co-developed-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com> Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2025-08-12 13:56:30 +03:00