License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 15:07:57 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-10-16 02:01:52 -04:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-08-05 09:22:24 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2019-11-29 08:17:25 +01:00
|
|
|
|
2010-10-27 15:32:57 -07:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-10-21 03:22:44 -04:00
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2025-09-01 22:50:21 +02:00
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-06-07 10:37:11 +02:00
|
|
|
|
2006-09-25 23:31:11 -07:00
|
|
|
|
2024-06-07 10:37:11 +02:00
|
|
|
|
2016-05-19 17:12:26 -07:00
|
|
|
|
2006-09-25 23:31:11 -07:00
|
|
|
|
2016-05-19 17:12:26 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2007-07-17 04:03:12 -07:00
|
|
|
|
2006-09-25 23:31:11 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mm/highmem: reimplement totalhigh_pages() by walking zones
Patch series "mm/highmem: don't track highmem pages manually".
Let's remove highmem special-casing from adjust_managed_page_count(), to
result in less confusion why memblock manually adjusts totalram_pages, and
__free_pages_core() only adjusts the zone's managed pages -- what about
the highmem pages that adjust_managed_page_count() updates?
Now, we only maintain totalram_pages and a zone's managed pages
independent of highmem support. We can derive the number of highmem pages
simply by looking at the relevant zone's managed pages. I don't think
there is any particular fast path that needs a maximum-efficient
totalhigh_pages() implementation.
Note that highmem memory is currently initialized using
free_highmem_page()->free_reserved_page(), not __free_pages_core(). In
the future we might want to also use __free_pages_core() to initialize
highmem memory, to make that less special, and consider moving
totalram_pages updates into __free_pages_core() [1], so we can just use
adjust_managed_page_count() in there as well.
Booting a simple kernel in QEMU reveals no highmem accounting change:
Before:
Memory: 3095448K/3145208K available (14802K kernel code, 2073K rwdata,
5000K rodata, 740K init, 556K bss, 49760K reserved, 0K cma-reserved,
2244488K highmem)
After:
Memory: 3095276K/3145208K available (14802K kernel code, 2073K rwdata,
5000K rodata, 740K init, 556K bss, 49932K reserved, 0K cma-reserved,
2244488K highmem)
[1] https://lkml.kernel.org/r/20240601133402.2675-1-richard.weiyang@gmail.com
This patch (of 2):
Can we get rid of the highmem ifdef in adjust_managed_page_count()?
Likely yes: we don't have that many totalhigh_pages() users, and they all
don't seem to be very performance critical.
So let's implement totalhigh_pages() like nr_free_highpages(), collecting
information from all zones. This is now similar to what we do in
si_meminfo_node() to collect the per-node highmem page count.
In the common case (single node, 3-4 zones), we really shouldn't care. We
could optimize a bit further (only walk ZONE_HIGHMEM and ZONE_MOVABLE if
required), but there doesn't seem a real need for that.
[david@redhat.com: fix build bot complaint]
Link: https://lkml.kernel.org/r/b57e5bc4-eb72-40e3-add4-57dfa6e03df6@redhat.com
Link: https://lkml.kernel.org/r/20240607083711.62833-1-david@redhat.com
Link: https://lkml.kernel.org/r/20240607083711.62833-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-06-07 10:37:10 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-05-04 18:40:09 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:34 +01:00
|
|
|
|
2012-07-31 16:45:02 -07:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
|
|
|
|
|
2012-07-31 16:45:02 -07:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
2012-07-31 16:45:02 -07:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mm: ptep_get() conversion
Convert all instances of direct pte_t* dereferencing to instead use
ptep_get() helper. This means that by default, the accesses change from a
C dereference to a READ_ONCE(). This is technically the correct thing to
do since where pgtables are modified by HW (for access/dirty) they are
volatile and therefore we should always ensure READ_ONCE() semantics.
But more importantly, by always using the helper, it can be overridden by
the architecture to fully encapsulate the contents of the pte. Arch code
is deliberately not converted, as the arch code knows best. It is
intended that arch code (arm64) will override the default with its own
implementation that can (e.g.) hide certain bits from the core code, or
determine young/dirty status by mixing in state from another source.
Conversion was done using Coccinelle:
----
// $ make coccicheck \
// COCCI=ptepget.cocci \
// SPFLAGS="--include-headers" \
// MODE=patch
virtual patch
@ depends on patch @
pte_t *v;
@@
- *v
+ ptep_get(v)
----
Then reviewed and hand-edited to avoid multiple unnecessary calls to
ptep_get(), instead opting to store the result of a single call in a
variable, where it is correct to do so. This aims to negate any cost of
READ_ONCE() and will benefit arch-overrides that may be more complex.
Included is a fix for an issue in an earlier version of this patch that
was pointed out by kernel test robot. The issue arose because config
MMU=n elides definition of the ptep helper functions, including
ptep_get(). HUGETLB_PAGE=n configs still define a simple
huge_ptep_clear_flush() for linking purposes, which dereferences the ptep.
So when both configs are disabled, this caused a build error because
ptep_get() is not defined. Fix by continuing to do a direct dereference
when MMU=n. This is safe because for this config the arch code cannot be
trying to virtualize the ptes because none of the ptep helpers are
defined.
Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 16:15:45 +01:00
|
|
|
|
2021-05-04 18:40:09 -07:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2025-12-11 12:38:19 -08:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2025-12-11 12:38:19 -08:00
|
|
|
|
2022-10-05 21:05:55 -07:00
|
|
|
|
2012-07-31 16:45:02 -07:00
|
|
|
|
|
|
|
|
|
2022-06-30 10:41:21 +02:00
|
|
|
|
2012-07-31 16:45:02 -07:00
|
|
|
|
2020-11-03 10:27:34 +01:00
|
|
|
|
2012-07-31 16:45:02 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-08-01 03:15:21 +02:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mm: ptep_get() conversion
Convert all instances of direct pte_t* dereferencing to instead use
ptep_get() helper. This means that by default, the accesses change from a
C dereference to a READ_ONCE(). This is technically the correct thing to
do since where pgtables are modified by HW (for access/dirty) they are
volatile and therefore we should always ensure READ_ONCE() semantics.
But more importantly, by always using the helper, it can be overridden by
the architecture to fully encapsulate the contents of the pte. Arch code
is deliberately not converted, as the arch code knows best. It is
intended that arch code (arm64) will override the default with its own
implementation that can (e.g.) hide certain bits from the core code, or
determine young/dirty status by mixing in state from another source.
Conversion was done using Coccinelle:
----
// $ make coccicheck \
// COCCI=ptepget.cocci \
// SPFLAGS="--include-headers" \
// MODE=patch
virtual patch
@ depends on patch @
pte_t *v;
@@
- *v
+ ptep_get(v)
----
Then reviewed and hand-edited to avoid multiple unnecessary calls to
ptep_get(), instead opting to store the result of a single call in a
variable, where it is correct to do so. This aims to negate any cost of
READ_ONCE() and will benefit arch-overrides that may be more complex.
Included is a fix for an issue in an earlier version of this patch that
was pointed out by kernel test robot. The issue arose because config
MMU=n elides definition of the ptep helper functions, including
ptep_get(). HUGETLB_PAGE=n configs still define a simple
huge_ptep_clear_flush() for linking purposes, which dereferences the ptep.
So when both configs are disabled, this caused a build error because
ptep_get() is not defined. Fix by continuing to do a direct dereference
when MMU=n. This is safe because for this config the arch code cannot be
trying to virtualize the ptes because none of the ptep helpers are
defined.
Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 16:15:45 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mm: ptep_get() conversion
Convert all instances of direct pte_t* dereferencing to instead use
ptep_get() helper. This means that by default, the accesses change from a
C dereference to a READ_ONCE(). This is technically the correct thing to
do since where pgtables are modified by HW (for access/dirty) they are
volatile and therefore we should always ensure READ_ONCE() semantics.
But more importantly, by always using the helper, it can be overridden by
the architecture to fully encapsulate the contents of the pte. Arch code
is deliberately not converted, as the arch code knows best. It is
intended that arch code (arm64) will override the default with its own
implementation that can (e.g.) hide certain bits from the core code, or
determine young/dirty status by mixing in state from another source.
Conversion was done using Coccinelle:
----
// $ make coccicheck \
// COCCI=ptepget.cocci \
// SPFLAGS="--include-headers" \
// MODE=patch
virtual patch
@ depends on patch @
pte_t *v;
@@
- *v
+ ptep_get(v)
----
Then reviewed and hand-edited to avoid multiple unnecessary calls to
ptep_get(), instead opting to store the result of a single call in a
variable, where it is correct to do so. This aims to negate any cost of
READ_ONCE() and will benefit arch-overrides that may be more complex.
Included is a fix for an issue in an earlier version of this patch that
was pointed out by kernel test robot. The issue arose because config
MMU=n elides definition of the ptep helper functions, including
ptep_get(). HUGETLB_PAGE=n configs still define a simple
huge_ptep_clear_flush() for linking purposes, which dereferences the ptep.
So when both configs are disabled, this caused a build error because
ptep_get() is not defined. Fix by continuing to do a direct dereference
when MMU=n. This is safe because for this config the arch code cannot be
trying to virtualize the ptes because none of the ptep helpers are
defined.
Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 16:15:45 +01:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mm: ptep_get() conversion
Convert all instances of direct pte_t* dereferencing to instead use
ptep_get() helper. This means that by default, the accesses change from a
C dereference to a READ_ONCE(). This is technically the correct thing to
do since where pgtables are modified by HW (for access/dirty) they are
volatile and therefore we should always ensure READ_ONCE() semantics.
But more importantly, by always using the helper, it can be overridden by
the architecture to fully encapsulate the contents of the pte. Arch code
is deliberately not converted, as the arch code knows best. It is
intended that arch code (arm64) will override the default with its own
implementation that can (e.g.) hide certain bits from the core code, or
determine young/dirty status by mixing in state from another source.
Conversion was done using Coccinelle:
----
// $ make coccicheck \
// COCCI=ptepget.cocci \
// SPFLAGS="--include-headers" \
// MODE=patch
virtual patch
@ depends on patch @
pte_t *v;
@@
- *v
+ ptep_get(v)
----
Then reviewed and hand-edited to avoid multiple unnecessary calls to
ptep_get(), instead opting to store the result of a single call in a
variable, where it is correct to do so. This aims to negate any cost of
READ_ONCE() and will benefit arch-overrides that may be more complex.
Included is a fix for an issue in an earlier version of this patch that
was pointed out by kernel test robot. The issue arose because config
MMU=n elides definition of the ptep helper functions, including
ptep_get(). HUGETLB_PAGE=n configs still define a simple
huge_ptep_clear_flush() for linking purposes, which dereferences the ptep.
So when both configs are disabled, this caused a build error because
ptep_get() is not defined. Fix by continuing to do a direct dereference
when MMU=n. This is safe because for this config the arch code cannot be
trying to virtualize the ptes because none of the ptep helpers are
defined.
Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 16:15:45 +01:00
|
|
|
|
2012-12-11 16:01:24 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2008-08-01 03:15:21 +02:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2008-08-01 03:15:21 +02:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:34 +01:00
|
|
|
|
2007-05-02 19:27:15 +02:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2007-05-02 19:27:15 +02:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2007-05-02 19:27:15 +02:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-03-19 17:00:42 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-02-04 22:29:26 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2006-04-02 13:47:35 +02:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2021-05-04 18:40:09 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2010-01-25 21:38:09 +01:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2025-09-01 22:50:21 +02:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-05-04 18:40:09 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-03-19 17:00:42 -07:00
|
|
|
|
2011-10-31 17:09:09 -07:00
|
|
|
|
2008-03-19 17:00:42 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-03-19 17:00:42 -07:00
|
|
|
|
2025-09-01 22:50:21 +02:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
2006-04-02 13:47:35 +02:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: MinChan Kim <minchan.kim@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
2009-03-04 22:49:41 -05:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2014-08-06 16:08:23 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-03-12 21:07:37 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-03-12 21:07:37 -08:00
|
|
|
|
2021-11-05 13:45:06 -07:00
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
2021-03-12 21:07:37 -08:00
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-03-12 21:07:37 -08:00
|
|
|
|
|
|
|
|
|
2021-11-05 13:45:06 -07:00
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
2021-03-12 21:07:37 -08:00
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-05 13:45:06 -07:00
|
|
|
|
2020-12-14 19:12:59 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:19 +01:00
|
|
|
|
2020-11-18 20:48:39 +01:00
|
|
|
|
2020-11-03 10:27:19 +01:00
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:39 +01:00
|
|
|
|
2020-11-03 10:27:19 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
2021-09-07 19:56:12 -07:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:31 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2025-09-01 22:50:21 +02:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-01-23 21:02:02 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2020-11-12 11:59:32 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
2020-11-12 11:59:32 +01:00
|
|
|
|
mm: ptep_get() conversion
Convert all instances of direct pte_t* dereferencing to instead use
ptep_get() helper. This means that by default, the accesses change from a
C dereference to a READ_ONCE(). This is technically the correct thing to
do since where pgtables are modified by HW (for access/dirty) they are
volatile and therefore we should always ensure READ_ONCE() semantics.
But more importantly, by always using the helper, it can be overridden by
the architecture to fully encapsulate the contents of the pte. Arch code
is deliberately not converted, as the arch code knows best. It is
intended that arch code (arm64) will override the default with its own
implementation that can (e.g.) hide certain bits from the core code, or
determine young/dirty status by mixing in state from another source.
Conversion was done using Coccinelle:
----
// $ make coccicheck \
// COCCI=ptepget.cocci \
// SPFLAGS="--include-headers" \
// MODE=patch
virtual patch
@ depends on patch @
pte_t *v;
@@
- *v
+ ptep_get(v)
----
Then reviewed and hand-edited to avoid multiple unnecessary calls to
ptep_get(), instead opting to store the result of a single call in a
variable, where it is correct to do so. This aims to negate any cost of
READ_ONCE() and will benefit arch-overrides that may be more complex.
Included is a fix for an issue in an earlier version of this patch that
was pointed out by kernel test robot. The issue arose because config
MMU=n elides definition of the ptep helper functions, including
ptep_get(). HUGETLB_PAGE=n configs still define a simple
huge_ptep_clear_flush() for linking purposes, which dereferences the ptep.
So when both configs are disabled, this caused a build error because
ptep_get() is not defined. Fix by continuing to do a direct dereference
when MMU=n. This is safe because for this config the arch code cannot be
trying to virtualize the ptes because none of the ptep helpers are
defined.
Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 16:15:45 +01:00
|
|
|
|
2020-11-12 11:59:32 +01:00
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2020-11-12 11:59:32 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:44 +01:00
|
|
|
|
|
|
|
|
|
2021-05-06 18:06:47 -07:00
|
|
|
|
2020-11-18 20:48:44 +01:00
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
mm: ptep_get() conversion
Convert all instances of direct pte_t* dereferencing to instead use
ptep_get() helper. This means that by default, the accesses change from a
C dereference to a READ_ONCE(). This is technically the correct thing to
do since where pgtables are modified by HW (for access/dirty) they are
volatile and therefore we should always ensure READ_ONCE() semantics.
But more importantly, by always using the helper, it can be overridden by
the architecture to fully encapsulate the contents of the pte. Arch code
is deliberately not converted, as the arch code knows best. It is
intended that arch code (arm64) will override the default with its own
implementation that can (e.g.) hide certain bits from the core code, or
determine young/dirty status by mixing in state from another source.
Conversion was done using Coccinelle:
----
// $ make coccicheck \
// COCCI=ptepget.cocci \
// SPFLAGS="--include-headers" \
// MODE=patch
virtual patch
@ depends on patch @
pte_t *v;
@@
- *v
+ ptep_get(v)
----
Then reviewed and hand-edited to avoid multiple unnecessary calls to
ptep_get(), instead opting to store the result of a single call in a
variable, where it is correct to do so. This aims to negate any cost of
READ_ONCE() and will benefit arch-overrides that may be more complex.
Included is a fix for an issue in an earlier version of this patch that
was pointed out by kernel test robot. The issue arose because config
MMU=n elides definition of the ptep helper functions, including
ptep_get(). HUGETLB_PAGE=n configs still define a simple
huge_ptep_clear_flush() for linking purposes, which dereferences the ptep.
So when both configs are disabled, this caused a build error because
ptep_get() is not defined. Fix by continuing to do a direct dereference
when MMU=n. This is safe because for this config the arch code cannot be
trying to virtualize the ptes because none of the ptep helpers are
defined.
Link: https://lkml.kernel.org/r/20230612151545.3317766-4-ryan.roberts@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305120142.yXsNEo6H-lkp@intel.com/
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-06-12 16:15:45 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2025-09-01 22:50:21 +02:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:40 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-07-06 13:15:19 +02:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:40 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-12 11:59:32 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:44 +01:00
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-03-24 21:37:53 -07:00
|
|
|
|
2022-04-08 13:08:55 -07:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-03-24 21:37:53 -07:00
|
|
|
|
2022-04-08 13:08:55 -07:00
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2021-11-19 16:43:55 -08:00
|
|
|
|
|
|
|
|
|
2020-11-18 20:48:43 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-11-03 10:27:18 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-12-11 16:01:23 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-08-17 13:45:09 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-03-19 17:00:42 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2011-08-17 13:45:09 +01:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-03-22 14:48:01 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-03-22 14:48:01 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2008-03-19 17:00:42 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2012-12-11 16:01:23 -08:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2022-03-22 14:48:01 -07:00
|
|
|
|
2005-04-16 15:20:36 -07:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2020-10-15 20:09:52 -07:00
|
|
|
|
