Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify IOCTL error message to print subsystem also.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum size of packet that can be handled by controller including ethernet
header is 65535. Reducing gso_max_size accordingly.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.
The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the GPIOs used by the MMCI driver are not registered yet when the driver is
probe()d, they can't be used. This happens if the mmci driver is probed before
the respective GPIO controller (e.g. on the LPC32xx EA3250 board, the PCA9532
GPIO controller would be initialized via DT after mmci). Therefore, we defer
mmci in this case.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Zero is a valid GPIO and shouldn't be handled as an error return code from
of_get_named_gpio(). It was a leftover from old code before getting
pdata->gpio_*() was modified.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the datasheet:
The LDO_CTRL registers are used to set the output voltage of LDO1 and LDO2.
LDO_CTRL[7] and LDO_CTRL[3] are reserved and should always be written to 0.
Thus the mask for TPS65023_LDO_1 and TPS65023_LDO_2 should be 0x07 and 0x70
respectively.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This documentation comment existed in an earlier patch set for
GPIO consolidation, so I'm saving it for maintainability of the
code.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 0bf7481 (pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails)
introduced the following build error:
drivers/pinctrl/pinctrl-mxs.c:140:3: error: implicit declaration of function 'free'
Use kfree function instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If ramp_delay is 0, delay value can be divided by zero.
This patch can fix the problem.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Atom CPUs don't have a register to retrieve TjMax. Detection so far was
incomplete. Use the X86 model ID to improve it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the Atom series D2000 and N2000 (Cedar Trail) as being supported.
List and set TjMax for those series.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the new Atom series (Tunnel Creek and Medfield) as being
supported, and list TjMax for the Atom E600 series.
Also enable the Atom tjmax heuristic for these Atom CPU models.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Pull drm fixes from Dave Airlie:
"Radeon is most of the work, one regression, one BUG fix in the new
prime code, some fixes to init code to make streamout not lock up the
hardware, and just some code to enable users to test HDMI audio on
later hw (its off by default).
Intel adds edp edid caching for some strange Dell Vostros that black
screen on startup if keep reading their EDID, and a fix for a DP
regression.
Otherwise fix for via/sis and one to stop udl binding to multiple
non-video usb."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
drm/radeon: add support for STRMOUT_BASE_UPDATE on 7xx
drm/radeon: add some additional 6xx/7xx/EG register init
drm/radeon: enable HDMI on DCE5 (AKA NI excluding Aruba)
drm sis: initialize object_idr
drm via: initialize object_idr
drm/radeon/prime: reserve/unreserve around pin
drm/radeon: fix regression in dynpm due to multi-ring rework
vga_switcheroo.h: fix pci_dev warning
drm/udl: only bind to the video devices on the hub.
For some reason one of the dev_err invocations is using a wrong
device so fix that.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable@vger.kernel.org
When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- two fixes for s3c-fb by Jingoo Han
(including a fix for a potential division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJP3OVbAAoJECSVL5KnPj1P+BoP/jf20UvGevLHaKYLxjB6elWP
cutoJFgfPWWdJcu6qwk4thR3fAZkB9R1vorFEp0EP7m8EkB8poP7pdPK7xGzbLKT
iGhWUy4pENcleyPu0mXE2kqLfq5g3fnPc9M0aiIySwfGAgjop24duP9NYMBL5sfr
GHs7JcrcyqWWVDHQLK3gx7JpVzoQOlN44yy64Su2GR8hfLUiSHC35AVnmK8svkra
S5dTa9RJJwVFowF8/o5bUzFuuMctKc22CbXA2NkR+PUHHc0zAqaRo0XedTr02C8u
bM9w7RWxQ71ZprJJeaBJgUbDev0JO9QxX7kA6eN3MRTHimi2wz9n2jy95R+H3ITm
EXhCl6F2kf+xzOfl9Ta9lB4eUthj2O1yBHGArpc5iJOuWHip2ggW4SrEyjKLrOpn
7AyB+D9gbZppnms4z5kCPM0Q/i/flyMoEccuaV4D3AaWw1miA4leQUtfjL/SGavl
9t6N6Zo2OT/h+Z36GauFnH3ap4lXNGZo3I03sFGp7E4VC0MDA8UnqG70zzdzm7BM
CO/c34HVpNBS0MH6blsUn+64aftJampqVzlQ0uj++5R1fpDGBCo+p+WEkIx9GGqN
bhJbmXR0HPnHtNQtf/LCPv98V/OAnWpfC98EeewPAQ3MTAexpdS8JduuY3PjhdhD
TkLBbb6A5UCU90SV32AD
=0Zkc
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- two fixes for s3c-fb by Jingoo Han (including a fix for a potential
division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
* tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6:
video: s3c-fb: fix possible division by zero in s3c_fb_calc_pixclk
video: s3c-fb: clear SHADOWCON register when clearing hardware window registers
drivers/tosa: driver needs I2C and SPI to compile
drivers/savagefb: use mdelay instead of udelay
video/console: automatically select a font
video/ili9320: do not mark exported functions __devexit
drivers/video: use correct __devexit_p annotation
video: bfin_adv7393fb: Convert to kstrtouint_from_user
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
They aren't going anywhere, and probing on DDC can cause the panel to
blank briefly, so read them up front and cache them for later queries.
v2: fix potential NULL derefs in intel_dp_get_edid_modes and
intel_dp_get_edid (Jani)
copy full EDID length, including extension blocks (Takashi)
free EDID on teardown (Takashi)
v3: malloc a new EDID buffer that's big enough for the memcpy (Chris)
v4: change handling of NULL EDIDs, just preserve the NULL behavior
across detects and mode list fetches rather than trying to re-fetch
the EDID (Chris)
v5: be glad that Chris is around to remind me to hit C-x C-s before
committing.
References: https://bugs.freedesktop.org/show_bug.cgi?id=46856
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 092945e11c.
This commit prevents a DP screen from properly training the link.
Oddly enough it works, once the machine has been warm-booted with an
older kernel.
According to DP docs this _should_ have been the right precharge time.
Also, the commit that originally introduces this was just general snb
DP enabling and didn't mention any specific reason for this special
value. Whatever, trust the reporter that this makes things worse and
let's just revert it.
v2: Less spelling fail.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: "Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl>
Buglink: https://lkml.org/lkml/2012/6/14/301
Cc: stable@vger.kernel.org (only for 3.4)
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new oui probe has been missing these.
This issue has been introduce in
commit 0d19832853
Author: Adam Jackson <ajax@redhat.com>
Date: Mon May 14 16:05:47 2012 -0400
drm/i915/dp: Probe branch/sink OUIs
v2: Do the eDP vdd dance of simply not probing the OUI on eDP panels
as suggested by Chris Wilson.
v3: Fix up the error path fail - I suck.
Cc: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50808
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugreport: http://permalink.gmane.org/gmane.comp.video.dri.devel/69695
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents the HDMI detect functions from poking at an eDP
connected panel, which can lead to trouble.
[danvet: Note that we have some other reports of DP vs. HDMI fighting,
but the general case is a much bigger fish to fry.]
References: https://bugs.freedesktop.org/show_bug.cgi?id=42278
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
After recent changes HDMI code is ready to be enabled on DCE5. This
patch just changes conditions to execute already present code on DCE5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The filed object_idr of struct drm_sis_private was introduced with
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=6de8a748881f1cd9d795454da2b6db616d5ca3d7 .
The idr_init(&dev->object_name_idr) is called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving object_idr
uninitialized. Correct this.
This patch was not tested because of lack of hardware.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The field obejct_idr of struct drm_via_private was introduced with the
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=77ee8f3825054f23b17e9c8f728f061defd86cdc .
In that patch idr_init(&dev->object_name_idr) was called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving the dev_priv->object_idr
uninitialized. To be more exact, the object_idr buffer is filled with zeros
because of kzalloc(), but the dev_priv->object_idr.lock spinlock can cause
system freeze at lib/idr.c:move_to_free_list() when spin_lock_irqsave()
is called on this spinlock.
The patch was tested on Clevo D4J, model D410J laptop, on the following
hardware, without AGP kernel module loaded:
# lspci -s 01:00.0 -n
01:00.0 0300: 1106:3108 (rev 01)
# lspci -s 01:00.0 -v
01:00.0 VGA compatible controller: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] (rev 01) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 4702
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 3.0
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I finally got to test this code a bit more and hit the ttm
no reserved assert, so add the reservations around the pinning.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all asics have all rings, so make sure the ring is ready
before attempting to check it in the dynpm work handler.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=43367
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a couple of minor fixes, one for a preempt warning in the mpt2sas
driver and one is a config failure with the new sd async domain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP2fuGAAoJEDeqqVYsXL0Md88IAMw1nLZkg39TzEM4tAkkCa4C
o3e3xcmUdO1lqswmgUDaD95Z0H9MUBxwHWQGiAQ7fheuyXXyGOLINkBTx7wOGksk
JpsjEHNhVwW2rxFwZDLYxvtBjRy9E6wJPeuBQxQdU2gGVzjmk2bAV6mJnf+/wDkH
uqJKnrmVNU7x5drw1wP2z0i3zm8UZVlB+eW3J5ReZzfQlpBYWmFcwxrSTp8Q03ko
rx+rMNYlQO+5Cp0/UZxdIlTw4TTaU+F6bXC8jPzZ2zj0mUWtBxiF6rYZQlebNM5n
/byCuivfM9OMeWaiwk5ERIQ/1iOUF4L5apCNUIG2PFtS7RY4349luWpBoeYkaVY=
=eNSh
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of minor fixes, one for a preempt warning in the
mpt2sas driver and one is a config failure with the new sd async
domain."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix sd_probe_domain config problem
[SCSI] mpt2sas: Fix unsafe using smp_processor_id() in preemptible
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJP2kcmAAoJEFjIrFwIi8fJXLcH/0a2m6KMcyjc4WaCHspAEFDL
9B055QUFDEOlH55wE2QeED/8D+0HUbTYnQBycH126XLKzLfRv1fsrKFKDSA/SWW2
Mh8N316UrY5Wc3KMdxXdCXJCDqDs7VhARTv6JdlUqUlH9oLRYE6CMRO8MujT0iwd
r+uEnNuW0udMFt8x9SnJW7pEaq7u2N5koEGdWEzZhfoumDaCRxm5OKAKXZ0DZlEZ
/BPjTW/N+Pf4u+bJZY+wQq41y4zGMqu7TDo/hOpuGZxeqtVnCE9trBbuGLnp4K+W
n4TfZZs9Y1kovSMj6qTeB0aP0F77tqHyXPb1oPKxm2kWfqT2dFtIRpuLtXYSC+o=
=cQl2
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull five Xen bug-fixes from Konrad Rzeszutek Wilk:
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
* tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mark local pages as FOREIGN in the m2p_override
xen/setup: filter APERFMPERF cpuid feature out
xen/balloon: Subtract from xen_released_pages the count that is populated.
xen/pci: Check for PCI bridge before using it.
xen/events: Add WARN_ON when quick lookup found invalid type.
xen/hvc: Check HVM_PARAM_CONSOLE_[EVTCHN|PFN] for correctness.
xen/hvc: Fix error cases around HVM_PARAM_CONSOLE_PFN
xen/hvc: Collapse error logic.
Here are a bunch of tiny fixes for the USB core and drivers for 3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for a number
of different regressions that have been reported recently. We also fixed some
PCI host controllers to resolve a long-standing bug with a whole class of host
controllers that have been plaguing people for a number of kernel releases,
preventing their systems from suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/byIEACgkQMUfUDdst+ykLBwCgiAi/cS4ObblcBEbnBvosPgsA
PqEAoJLMAwhcozeEOWLhb++45Vs+UjKv
=HAWc
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of tiny fixes for the USB core and drivers for
3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for
a number of different regressions that have been reported recently.
We also fixed some PCI host controllers to resolve a long-standing bug
with a whole class of host controllers that have been plaguing people
for a number of kernel releases, preventing their systems from
suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (41 commits)
USB: fix gathering of interface associations
usb: ehci-sh: fix illegal phy_init() running when platform_data is NULL
usb: cdc-acm: fix devices not unthrottled on open
Fix OMAP EHCI suspend/resume failure (i693)
USB: ohci-hub: Mark ohci_finish_controller_resume() as __maybe_unused
usb: use usb_serial_put in usb_serial_probe errors
USB: EHCI: Fix build warning in xilinx ehci driver
USB: fix PS3 EHCI systems
xHCI: Increase the timeout for controller save/restore state operation
xhci: Don't free endpoints in xhci_mem_cleanup()
xhci: Fix invalid loop check in xhci_free_tt_info()
xhci: Fix error path return value.
USB: Checking the wrong variable in usb_disable_lpm()
usb-storage: Add 090c:1000 to unusal-devs
USB: serial-generic: use a single set of device IDs
USB: serial: Enforce USB driver and USB serial driver match
USB: add NO_D3_DURING_SLEEP flag and revert 151b612847
USB: option: add more YUGA device ids
USB: mos7840: Fix compilation of usb serial driver
USB: option: fix memory leak
...
Pull IDE fixes from David S. Miller:
1) Two fixes to icside, one for a build failure and another for a
warning. From Christian Dietrich.
2) Fix a bit operation that did erroneous masking, from Julia Lawall.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
drivers/ide/ide-cs.c: adjust suspicious bit operation
ide: icside.c: fix printk format string compile warning
ide: icside.c: Fix compile with CONFIG_BLK_DEV_IDEDMA_ICS=n
Pull target updates from Nicholas Bellinger:
"This series contains post merge qla_target.c / tcm_qla2xxx bugfixes
from the past weeks, including the patch to allow target-core to use
an optional session shutdown callback to help address an active I/O
shutdown bug in tcm_qla2xxx code (Joern).
Also included is a target regression bugfix releated to explict ALUA
target port group CDB emulation that is CC'ed to stable (Roland)."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Remove version.h header file inclusion
tcm_qla2xxx: Handle malformed wwn strings properly
tcm_qla2xxx: tcm_qla2xxx_handle_tmr() can be static
qla2xxx: Don't leak commands we give up on in qlt_do_work()
qla2xxx: Don't crash if we can't find cmd for failed CTIO
tcm_qla2xxx: Don't insert nacls without sessions into the btree
target: Return error to initiator if SET TARGET PORT GROUPS emulation fails
tcm_qla2xxx: Clear session s_id + loop_id earlier during shutdown
tcm_qla2xxx: Convert to TFO->put_session() usage
target: Add TFO->put_session() caller for HW fabric session shutdown
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We
allocate it that way a few lines earlier in the function. So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.
A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()
This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.
bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: Tomas Hruby <thruby@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true. The intent here was to test
that both flags were set.
Cc: <stable@kernel.org> # 2.6.39+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.
The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.
The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Reported-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two new devices for this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of ep_dequeue , if dequeued request was submitted for dma
transfer, then endpoint is stopped. Once endpoint is stooped, callback
for the dequeued request must be called.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The documentation lives in drivers/staging/iio/Documentation, but
according to Jonathan it's obsolete and needs fixing.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't create a link from the device to the compatibility switch class
since we already create a link from the device to to the extcon class
object and we try to use the same name for both links. This causes a loud
complaint from sysfs on boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TEAC's UD-H01 (and probably other devices) have a gap in the interface
number allocation of their descriptors:
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 220
bNumInterfaces 3
[...]
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
[...]
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 2
bInterfaceCount 2
bFunctionClass 1 Audio
bFunctionSubClass 0
bFunctionProtocol 32
iFunction 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
[...]
Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.
The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.
In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.
Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: bEN <ml_all@circa.be>
Reported-by: Ivan Perrone <ivanperrone@hotmail.com>
Tested-by: ivan perrone <ivanperrone@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform_data is not set, pdata will be uninitialized value.
Since the driver has the following code, if the condition is true when
the pdata is uninitialized value, the driver may jump to the illegal
phy_init().
if (pdata && pdata->phy_init)
pdata->phy_init();
This patch also fixes the following warning:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-sh.c: In function ‘ehci_hcd_sh_probe’:
drivers/usb/host/ehci-sh.c:104: warning: ‘pdata’ may be used uninitialized in this function
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>