There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register needs to be updated with masked writes.
This was found by code inspection and comparison with Bspec and
doesn't seem to fix any known issue.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Add note about impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-EDEADLK has special meaning in atomic, but get_fence may call
i915_find_fence_reg which can return -EDEADLK.
This has special meaning in the atomic world, so convert the error
to -EBUSY for this case.
Changes since v1:
- Add comment in the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rest will be a noop anyway, since without modeset there will be
no updated dplls and no modeset state to update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
connectors_active will be removed, so just calculate this instead.
Changes since v1:
- Look for the right pointer in intel_sanitize_encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of allocating pipe_config on the stack use the old
crtc_state, it's only going to freed from this point on.
All crtc' are now only checked once during modeset,
because false positives can happen with encoders after
dpms changes and to limit the amount of errors for 1 failure.
Changes since v1:
- crtc_state -> old_crtc_state
- state -> old_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connectors are updated atomically now, so the only interaction
with the encoder is through base.crtc.
If it's NULL the encoder's not part of any crtc, and if it's
not NULL then active should be equal to crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is handled by the atomic core now, no need to check this for ourself.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now dpms callbacks can still fiddle with the connector state,
but it can only turn connectors off.
This is remediated by only checking crtc->state->active when the
connector is active, and ignore crtc->state->active when the
connector is off.
connectors_active is no longer checked, and will be removed later
in this series together with dpms.
Another check for !encoder->crtc is performed by check_encoder_state
too, so it can be removed.
Changes since v1:
- Add commit message.
- rename state to old_state.
- Move deletion of mst_port check to mst patch.
Changes since v2:
- Fix a null pointer dereference on MST now hw readout is fixed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fully remove the MST connector from the atomic state, and remove the
early returns in check_*_state for MST connectors.
With atomic the state can be made consistent all the time.
Thanks to Sivakumar Thulasimani for the idea of using
drm_atomic_helper_set_config.
Changes since v1:
- Remove the MST check in intel_connector_check_state too.
Changes since v2:
- Use drm_atomic_helper_set_config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set connectors_changed to force a modeset if the panel fitter's force
enabled on eDP.
Changes since v1:
- Use connectors_changed instead of active_changed because it's a
routing update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bit was not according to ieee80211 specification.
Fix that.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the out-of-line average calculation, use the new
DECLARE_EWMA() macro to declare a signal EWMA, and use that.
This actually *reduces* the code size slightly (on x86-64) while
also reducing the station info size by 80 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having the EWMA parameters stored in the runtime struct imposes
memory requirements for the constant values that could just be
inlined in the code. This particularly makes sense if there are
a lot of such structs, for example in mac80211 in the station
table where each station has a number of these in an array, and
there can be many stations.
Provide a macro DECLARE_EWMA() that declares the necessary struct
and inline functions to access it with the parameters hard-coded;
using this also means the user no longer needs to 'select AVERAGE'
as it's entirely self-contained.
In the mac80211 case, on x86-64, this actually slightly *reduces*
code size, while also saving 80 bytes of runtime memory per sta.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hwsim_init_netlink(), we should call genl_unregister_family()
if failed on netlink_register_notifier() since the genetlink is
already registered.
Signed-off-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define rc_rateidx_vht_mcs_mask array and rate_idx_match_vht_mcs_mask()
method in order to apply mcs mask for vht rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define rate_control_apply_mask_ratetbl() in order to apply ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove ieee80211_tx_rate dependency in rate_idx_match_legacy_mask(),
rate_idx_match_mcs_mask() and rate_idx_match_mask() in order to use the
previous logic to define a ratemask in rate_control_set_rates() for
station rate table. Moreover move rate mask definition logic in
rate_control_cap_mask()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unnecessary ieee80211_tx_info pointer from rate_control_apply_mask
signature. rate_control_apply_mask() will be used to define a ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Perform the BSS_CHANGED_BSSID action when joining an OCB network.
This is required to set the broadcast BSSID in some network drivers.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently OCB mode accepts frames with bssid==broadcast and type!=beacon.
Some non-data frames are sent matching this, for example probe responses.
This results in unnecessary creation of STA entries.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make mac80211 accept the multicast rate requested by the user the
rate control should be told that it is operating in BSS mode.
Without this, the default rate is selected in rate_control_send_low
(!pubsta and !txrc->bss)
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow setting multicast rate on OCB interfaces.
Current behaviour results in EOPNOTSUPP when attempting this.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If driver failed to setup wiphy params (e.g. rts
threshold, fragmentation treshold) userspace
wasn't properly notified about this. This could
lead to user confusion who would think the command
succeeded even if that wasn't the case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original assumption of 20MHz wide channels hasn't been true since
the addition of support for 5 and 10 MHz channels.
Change the code to no longer disable all channels that don't fit into
the 20MHz grid, but instead set the appropriate flags to disable
operation on specific bandwidths.
Signed-off-by: Matthias May <matthias.may@neratec.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ACK of an inexistent IRQ can trigger an spurious IRQ that breaks the
txrx logic. This has been observed on axi_quad_spi:3.2 core.
This patch only ACKs IRQs that have not been Acknowledge jet.
Reported-by: Edward Kigwana <ekigwana@scires.com>
Tested-by: Edward Kigwana <ekigwana@scires.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Don't set .read_flag_mask for adav803, it's for adav801 only.
Fixes: 0c2d696456 ("ASoC: adav80x: Split SPI and I2C code into different modules")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since commit 1329e8cc69 ("modsign: Extract signing cert from
CONFIG_MODULE_SIG_KEY if needed"), the build system has carefully coped
with the signing key being specified as a relative path in either the
source or or the build trees.
However, the actual signing of modules has not worked if the filename
is relative to the source tree.
Fix that by moving the config_filename helper into scripts/Kbuild.include
so that it can be used from elsewhere, and then using it in the top-level
Makefile to find the signing key file.
Kill the intermediate $(MODPUBKEY) and $(MODSECKEY) variables too, while
we're at it. There's no need for them.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
We couldn't use if_changed for this before, because it didn't live in
the kernel/ directory so we couldn't add it to $(targets). It was easier
just to leave it as it was.
Now it's in the certs/ directory we can use if_changed, the same as we
do for the trusted certificate list.
Aside from making things consistent, this means we don't need to depend
explicitly on the include/config/module/sig/key.h file. And we also get
to automatically do the right thing and re-extract the cert if the user
does odd things like using a relative filename and then playing silly
buggers with adding/removing that file in both the source and object
trees. We always favour the one in the object tree if it exists, and
now we'll correctly re-extract the cert when it changes. Previously we'd
*only* re-extract the cert if the config option changed, even if the
actual file we're using did change.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Move certificate handling out of the kernel/ directory and into a certs/
directory to get all the weird stuff in one place and move the generated
signing keys into this directory.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: David Woodhouse <David.Woodhouse@intel.com>
USB Audio Class version 2.0 supports three different parameter block sizes for
CUR requests, which are 1 byte (5.2.3.1 Layout 1 Parameter Block), 2 bytes
(5.2.3.2 Layout 2 Parameter Block) and 4 bytes (5.2.3.3 Layout 3 Parameter
Block). Use the correct size according to the specific control as it was
already done for UACv1. The allocated block size for control requests is
increased to support the 4 byte worst case.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add Tegra-specific configuration options to multi_v7_defconfig:
* HDA controller and codec support
* Watchdog support
* Nouveau (for GK20A GPU) support
Signed-off-by: Thierry Reding <treding@nvidia.com>
* pci/host-dra7xx:
ARM: dts: am57xx-evm: Add 'gpios' property with gpio2_8
PCI: dra7xx: Add support to make GPIO drive PERST# line
PCI: dra7xx: Clear MSE bit during suspend so clocks will idle
PCI: dra7xx: Add PM support
PCI: dra7xx: Disable pm_runtime on get_sync failure
* pci/host-iproc:
PCI: iproc: Allow BCMA bus driver to be built as module
PCI: iproc: Add arm64 support
PCI: iproc: Delete unnecessary checks before phy calls
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
EEH (Enhanced Error Handling) allows a driver to recover from the
temporary failure of an attached PCI card. Enable basic CXL support
for EEH.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the driver doesn't participate in EEH, the AFUs will be removed
by cxl_remove, which will be invoked by EEH.
If the driver does particpate in EEH, the vPHB needs to stick around
so that the it can particpate.
In both cases, we shouldn't remove the AFU/vPHB.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As with an adapter, some aspects of initialisation are done only once
in the lifetime of an AFU: for example, allocating memory, or setting
up sysfs/debugfs files.
However, we may want to be able to do some parts of the initialisation
multiple times: for example, in error recovery we want to be able to
tear down and then re-map IO memory and IRQs.
Therefore, refactor AFU init/teardown as follows.
- Create two new functions: 'cxl_configure_afu', and its pair
'cxl_deconfigure_afu'. As with the adapter functions,
these (de)configure resources that do not need to last the entire
lifetime of the AFU.
- Allocating and releasing memory remain the task of 'cxl_alloc_afu'
and 'cxl_release_afu'.
- Once-only functions that do not involve allocating/releasing memory
stay in the overarching 'cxl_init_afu'/'cxl_remove_afu' pair.
However, the task of picking an AFU mode and activating it has been
broken out.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some aspects of initialisation are done only once in the lifetime of
an adapter: for example, allocating memory for the adapter,
allocating the adapter number, or setting up sysfs/debugfs files.
However, we may want to be able to do some parts of the
initialisation multiple times: for example, in error recovery we
want to be able to tear down and then re-map IO memory and IRQs.
Therefore, refactor CXL init/teardown as follows.
- Keep the overarching functions 'cxl_init_adapter' and its pair,
'cxl_remove_adapter'.
- Move all 'once only' allocation/freeing steps to the existing
'cxl_alloc_adapter' function, and its pair 'cxl_release_adapter'
(This involves moving allocation of the adapter number out of
cxl_init_adapter.)
- Create two new functions: 'cxl_configure_adapter', and its pair
'cxl_deconfigure_adapter'. These two functions 'wire up' the
hardware --- they (de)configure resources that do not need to
last the entire lifetime of the adapter
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- MMIO pointer unmapping is guarded by a null pointer check.
However, iounmap doesn't null the pointer, just invalidate it.
Therefore, explicitly null the pointer after unmapping.
- afu_desc_mmio also needs to be unmapped.
- PCI regions are allocated in cxl_map_adapter_regs.
Therefore they should be released in unmap, not elsewhere.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check if an IRQ is mapped before releasing it.
This will simplify future EEH code by allowing unconditional unmapping
of IRQs.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
