Introduce register look up table as different SOC venders
may have different register offset for the some register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce register accessor to ease loop up table access
in later patch.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename regs with enumeration to generalize register names.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).
Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.
NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "ti,dra742-uart" to the compatible list so the driver
workaround for UART module disable errata is enabled.
This does not break backward compatibility as existing DTBs
should continue to work with newer kernels albeit without the
capability to idle the UART module when DMA is used.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.
Fixes: commit b5199d4681 ("tty/serial: at91: add support to FIFOs")
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementing enable_ms is optional by serial_core.
check_modem_status is just an empty local function.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus check on pm_runtime_active that prevented
disconnection from a client in case the device was resuming
from power gating but not yet active.
Fix regression introduced by
18901357e7
mei: disconnect on connection request timeout
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Access to the BQ24190's configurable charge type property (none, trickle,
fast) is being masked by an incorrect power_supply_property entry. After
applying this patch a new 'charge_type' property will appear in the
bq24190-charger sysfs folder backed up by getters/setters already
present in the driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Now that we can get there in RCU mode, we shouldn't play with
nd->path.dentry->d_inode - it's not guaranteed to be stable.
Use nd->inode instead.
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The USB Battery Charging spec (BC1.2) suggests a dedicated
charging port can deliver from 0.5 to 5.0A at between 4.75 and 5.25
volts.
To choose the "correct" current voltage setting requires a trial
and error approach: try to draw current and see if the voltage drops
too low.
Even with a configured Standard Downstream Port, it may not be possible
to reliably pull 500mA - depending on cable quality and source
quality I have reports of charging failure due to the voltage dropping
too low.
To address both these concerns, this patch introduce incremental
current setting.
The current pull from VBUS is increased in steps of 20mA every 100ms
until the target is reached or until the measure voltage drops below
4.75V. If the voltage does go too low, the target current is reduced
by 20mA and kept there.
This applies to currents selected automatically, or to values
set via sysfs. So setting a large value will cause the maximum
available to be used - up to the limit of 1.7A imposed by the
hardware.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This allows AC charging to be turned off, much like usb charging.
"continuous" mode is not available though.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a 'continuous' option for usb charging which enables
the "linear" charging mode of the twl4030.
Linear charging does a good job with not-so-reliable power sources.
Auto mode does not work well as it switches off when voltage drops
momentarily. Care must be taken not to over-charge.
It was used with a bike hub dynamo since a year or so. In that case
there are automatically charging stops when the cyclist needs a break.
Original-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'off' or 'auto' to
/sys/class/power/twl4030_usb/mode
will now enable or disable charging from USB port. Normally this is
enabled on 'plug' and disabled on 'unplug'.
Unplug will still disable charging. 'plug' will only enable it if
'auto' if selected.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'max_current' sysfs attributes are created which allow the
max to be set.
Whenever a current source changes, the default is restored.
This will be followed by a uevent, so user-space can decide to
update again.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 charger has two current sources, 'USB' and 'AC'
(presumably "Accessory Charger" because it isn't Alternating Current).
If 'AC' is providing current, we should set the current limit
differently to when it isn't (and so USB is used).
So split 'cur' into 'usb_cur' and 'ac_cur' and use accordingly.
Now we must review the current setting on any interrupt or USB
event which might indicate that the charger-source has changed.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If CONFIG_SH_DMAE_BASE (which is required for DMA engine support for
legacy SH, SH/R-Mobile, and R-Car Gen1, but not for R-Car Gen2) is not
enabled, but CONFIG_RCAR_DMAC (for R-Car Gen2 DMA engine support) is,
and the DTS doesn't provide a "dmas" property for a device,
dma_request_slave_channel_compat() incorrectly succeeds, and returns a
DMA channel.
However, when trying to use that DMA channel later, it fails with:
rcar-dmac e6700000.dma-controller: rcar_dmac_prep_slave_sg: bad parameter: len=1, id=-22
(Fortunately most drivers can handle this failure, and fall back to
PIO)
The reason for this is that a NULL legacy filter function is used, which
actually means "all channels are OK", not "do not match".
If CONFIG_SH_DMAE_BASE is enabled (like in shmobile_defconfig, which
supports other SoCs besides R-Car Gen2), shdma_chan_filter() correctly
returns false, as no available channel on R-Car Gen2 matches a
shdma-base channel.
If the DTS does provide a "dmas" property, dma_request_slave_channel()
succeeds, and legacy filter-based matching is not used.
To fix this, change shdma_chan_filter from being NULL to a dummy
function that always returns false, like is done on other platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DEV_TO_DEV support for i.MX SDMA driver to support data
transfer between two peripheral FIFOs.
The per_2_per script requires two peripheral addresses and two DMA
requests, and it need to check the src addr and dst addr is in the SPBA
bus space or in the AIPS bus space.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The twl4030 allows control of the incoming current.
Part of this control is a 'CGAIN' setting which doubles
the range for half the precision. This control affects
several different current setting, so all need to be updated
at once when CGAIN is changed.
With this patch, all of these current setting are managed
by the driver, but most are left at their default settings.
The current drawn is set to 500mA if the allow_usb module parameter is
set, and to 100mA otherwise.
More fine control will appear in later patches.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We will need this calculation in other places, so
create functions to map between register value and uA value.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The usb phy driver already determines when VBUS is available,
so repeating the test in the charger driver is pointless duplication.
On probe, process the last event from the phy, and from then on,
do whatever the phy tells us without double-checking.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Now that twl4030_bci_probe can safely return -EPROBE_DEFER,
do so when devm_usb_get_phy_by_node returns that error.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Drivers using module_platform_driver_probe cannot return
EPROBE_DEFER from the probe function, which makes them rather useless
these days...
Convert to module_platform_driver() so EPROBE_DEFER can be used.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.
commit ab37813f40
twl4030_charger: Allow charger to control the regulator that feeds it
gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.
Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.
So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
* pci/irq:
PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
* pci/misc:
PCI: Remove unused "pci_probe" flags
PCI: Add VPD function 0 quirk for Intel Ethernet devices
PCI: Add dev_flags bit to access VPD through function 0
PCI / ACPI: Fix pci_acpi_optimize_delay() comment
PCI: Remove a broken link in quirks.c
PCI: Remove useless redundant code
PCI: Simplify pci_find_(ext_)capability() return value checks
PCI: Move PCI_FIND_CAP_TTL to pci.h and use it in quirks
PCI: Add pcie_downstream_port() (true for Root and Switch Downstream Ports)
PCI: Fix pcie_port_device_resume() comment
PCI: Shift PCI_CLASS_NOT_DEFINED consistently with other classes
PCI: Revert aeb30016fe ("PCI: add Intel USB specific reset method")
PCI: Fix TI816X class code quirk
PCI: Fix generic NCR 53c810 class code quirk
PCI: Use PCI_CLASS_SERIAL_USB instead of bare number
PCI: Add quirk for Intersil/Techwell TW686[4589] AV capture cards
PCI: Remove Intel Cherrytrail D3 delays
* pci/resource:
PCI: Call pci_read_bridge_bases() from core instead of arch code
* pci/virtualization:
PCI: Restore ACS configuration as part of pci_restore_state()
* pci/host-designware:
PCI: designware: Don't complain missing *config* reg space if va_cfg0 is set
* pci/host-xgene:
PCI: xgene: Add support for a 64-bit prefetchable memory window
arm64: dts: Add APM X-Gene PCIe 64-bit prefetchable window
PCI: xgene: Drop owner assignment from platform_driver
* pci/host-xilinx:
PCI: xilinx: Check for MSI interrupt flag before handling as INTx
This indicates the device coordinates should be directly mapped to screen.
This is valid since scaling/flipping/rotation should be done by configuring
the MXT device.
It also flags to Android using INPUT_PROP_DIRECT that the device should be
treated as a touch screen by default, and removes the necessity for a
default IDC file.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The CHG/interrupt line is momentarily set (approximately 100 ms) as an
input after power-up or reset for diagnostic purposes. This may cause
spurious interrupts, so disable interrupt handler during this period.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use function rather than loop, define np to reduce wrapping.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_dev may be NULL if mxt_initialize_input_device fails. But pm ops is
still available and suspend/resume assume
input_dev is not NULL. To fix this issue, we add a check if (!input_dev).
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many of these values are out of date and they aren't used in the driver
- all they do is increase the size of the kernel source.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The hardcoded 0x83 CTRL setting overrides other settings in that byte,
enabling extra reporting that may not be useful on a particular platform.
Implement improved suspend mechanism via deep sleep. By writing zero to
both the active and idle cycle times the maXTouch device can be put into a
deep sleep mode, using minimal power. It is necessary to issue a calibrate
command after the chip has spent any time in deep sleep, however a soft
reset is unnecessary.
Use the old method on Chromebook Pixel via platform data option.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
After a config download, the T7 power configuration may have changed so it
is necessary to re-read it.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without this initialization, gateways which actually announce up/down
bandwidth of 0/0 could be added. If these nodes get purged via
_batadv_purge_orig() later, the gw_node structure does not get removed
since batadv_gw_node_delete() updates the gw_node with up/down
bandwidth of 0/0, and the updating function then discards the change
and does not free gw_node.
This results in leaking the gw_node structures, which references other
structures: gw_node -> orig_node -> orig_node_ifinfo -> hardif. When
removing the interface later, the open reference on the hardif may cause
hangs with the infamous "unregister_netdevice: waiting for mesh1 to
become free. Usage count = 1" message.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The tt_local_entry deletion performed in batadv_tt_local_remove() was neither
protecting against simultaneous deletes nor checking whether the element was
still part of the list before calling hlist_del_rcu().
Replacing the hlist_del_rcu() call with batadv_hash_remove() provides adequate
protection via hash spinlocks as well as an is-element-still-in-hash check to
avoid 'blind' hash removal.
Fixes: 068ee6e204 ("batman-adv: roaming handling mechanism redesign")
Reported-by: alfonsname@web.de
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
batadv_softif_vlan_get() may return NULL which has to be verified
by the caller.
Fixes: 35df3b298f ("batman-adv: fix TT VLAN inconsistency on VLAN re-add")
Reported-by: Ryan Thompson <ryan@eero.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When a node running DAT receives an ARP request from the LAN for the
first time, it is likely that this node will request the ARP entry
through the distributed ARP table (DAT) in the mesh.
Once a DAT reply is received the asking node must check if the MAC
address for which the IP address has been asked is local. If it is, the
node must drop the ARP reply bceause the client should have replied on
its own locally.
Forwarding this reply means fooling any L2 bridge (e.g. Ethernet
switches) lying between the batman-adv node and the LAN. This happens
because the L2 bridge will think that the client sending the ARP reply
lies somewhere in the mesh, while this node is sitting in the same LAN.
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The audit watch parent count was imbalanced, adding an unnecessary layer of
watch parent references. Decrement the additional parent reference when a
watch is reused, already having a reference to the parent.
audit_find_parent() gets a reference to the parent, if the parent is
already known. This additional parental reference is not needed if the
watch is subsequently found by audit_add_to_parent(), and consumed if
the watch does not already exist, so we need to put the parent if the
watch is found, and do nothing if this new watch is added to the parent.
If the parent wasn't already known, it is created with a refcount of 1
and added to the audit_watch_group, then incremented by one to be
subsequently consumed by the newly created watch in
audit_add_to_parent().
The rule points to the watch, not to the parent, so the rule's refcount
gets bumped, not the parent's.
See LKML, 2015-07-16
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
