dw_mci_exynos_resume_noirq() performs DWMMC register access without
ensuring that respective clocks are enabled. This might cause external
abort on some systems (observed on Exynos5433 based boards). Fix this
by forcing a PM runtime active state before register access. Using
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS allows also to cleanup conditional code
a bit.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.
The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 1268ed0c47 ("x86/hyper-v: Fix the circular dependency in IPI
enlightenment") pre-filled hv_vp_index with VP_INVAL so it is now
(theoretically) possible to observe hv_cpu_number_to_vp_number()
returning VP_INVAL. We need to check for that in hyperv_flush_tlb_others().
Not checking for VP_INVAL on the first call site where we do
if (hv_cpu_number_to_vp_number(cpumask_last(cpus)) >= 64)
goto do_ex_hypercall;
is OK, in case we're eligible for non-ex hypercall we'll catch the
issue later in for_each_cpu() cycle and in case we'll be doing ex-
hypercall cpumask_to_vpset() will fail.
It would be nice to change hv_cpu_number_to_vp_number() return
value's type to 'u32' but this will likely be a bigger change as
all call sites need to be checked first.
Fixes: 1268ed0c47 ("x86/hyper-v: Fix the circular dependency in IPI enlightenment")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: "Michael Kelley (EOSG)" <Michael.H.Kelley@microsoft.com>
Cc: devel@linuxdriverproject.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180709174012.17429-3-vkuznets@redhat.com
Commit 1268ed0c47 ("x86/hyper-v: Fix the circular dependency in IPI
enlightenment") made cpumask_to_vpset() return '-1' when there is a CPU
with unknown VP index in the supplied set. This needs to be checked before
we pass 'nr_bank' to hypercall.
Fixes: 1268ed0c47 ("x86/hyper-v: Fix the circular dependency in IPI enlightenment")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: "Michael Kelley (EOSG)" <Michael.H.Kelley@microsoft.com>
Cc: devel@linuxdriverproject.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180709174012.17429-2-vkuznets@redhat.com
Remove the modes timings tables for DMT modes and calculate the HW
paremeters from the modes timings.
Switch the DMT modes pixel clock calculation out of the static frequency
list to a generic calculation from a range of possible PLL dividers.
This patch is an intermediate step towards usage of the Common Clock
Framwework for PLL setup, by reworking the code to have common
sel_pll() function called by the CEA (HDMI) freq setup and the generic
DMT frequencies setup, we should be able to simply call clk_set_rate()
on the PLL clock handle in a near future.
The CEA (HDMI) and CVBS modes needs very specific clock paths that CCF will
never be able to determine by itself, so there is still some work to do for
a full handoff to CCF handling the clocks.
This setup permits setting non-CEA modes like :
- 1600x900-60Hz
- 1280x1024-75Hz
- 1280x1024-60Hz
- 1440x900-60Hz
- 1366x768-60Hz
- 1280x800-60Hz
- 1152x864-75Hz
- 1024x768-75Hz
- 1024x768-70Hz
- 1024x768-60Hz
- 832x624-75Hz
- 800x600-75Hz
- 800x600-72Hz
- 800x600-60Hz
- 640x480-75Hz
- 640x480-73Hz
- 640x480-67Hz
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: fixed trivial checkpatch issues]
Link: https://patchwork.freedesktop.org/patch/msgid/1531726814-14638-1-git-send-email-narmstrong@baylibre.com
Pio-leds (near GPIO-Header) are swapped and LOW-active.
This patch restores the expected behaviour.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Both functions declared in rtl8188e_led.h are also declared in
rtw_led.h which is included from drv_types.h. Remove rtl8188e_led.h
and it's includes.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not line break function definition of Efuse_PowerSwitch().
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove custom is_multicast_mac_addr() and is_broadcast_mac_addr().
Use is_multicast_ether_addr() instead.
By definition the broadcast address is also a multicast address.
is_multicast_ether_addr() returns true for broadcast addresses.
Hence checking for multicast in the conditional is sufficient.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch warnings:
Use #include <linux/pci.h> instead of <asm/pci.h>
Use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Oliver Hübers <oliver.huebers@web.de>
Signed-off-by: Vanessa Borgmann <nessa.x@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix for a style warning reported by checkpatch.pl in KConfig
suggesting to use 'help' instead of '---help---'.
Signed-off-by: Cristian Kubis <cristian.kubis@tsunix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put data to skb, decrypt with lib80211_crypt_ccmp, and place back to tx buffer.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put data to skb, decrypt with lib80211_crypt_tkip, and place back to tx buffer.
MIC calculation will be replaced later.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the kernel configuration, early ARM architecture setup code
may have attached the GPU to a DMA/IOMMU mapping that transparently uses
the IOMMU to back the DMA API. Tegra requires special handling for IOMMU
backed buffers (a special bit in the GPU's MMU page tables indicates the
memory path to take: via the SMMU or directly to the memory controller).
Transparently backing DMA memory with an IOMMU prevents Nouveau from
properly handling such memory accesses and causes memory access faults.
As a side-note: buffers other than those allocated in instance memory
don't need to be physically contiguous from the GPU's perspective since
the GPU can map them into contiguous buffers using its own MMU. Mapping
these buffers through the IOMMU is unnecessary and will even lead to
performance degradation because of the additional translation. One
exception to this are compressible buffers which need large pages. In
order to enable these large pages, multiple small pages will have to be
combined into one large (I/O virtually contiguous) mapping via the
IOMMU. However, that is a topic outside the scope of this fix and isn't
currently supported. An implementation will want to explicitly create
these large pages in the Nouveau driver, so detaching from a DMA/IOMMU
mapping would still be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Instead of setting the DMA ops pointer to NULL, set the correct,
non-IOMMU ops depending on the device's coherency setting.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In the quest to remove all stack VLA usage from the kernel[1], this
allocates the working buffers before starting the writing so it won't
abort in the middle. This needs an initial walk of the lists to figure
out how large the buffer should be.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_framebuffer. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Similar to commit 0bf8bf50ed ("module: Remove
const attribute from alias for MODULE_DEVICE_TABLE")
Fixes many -Wduplicate-decl-specifier warnings due to the combination of
const typeof() of already const variables.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Smatch complains that "value" can be uninitialized when kstrtol()
returns -ERANGE.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Noticed this as I was skimming through, if we fail to allocate memory
for cli we'll end up returning without dropping the runtime PM ref we
got. Additionally, we'll even return the wrong return code! (ret most
likely will == 0 here, we want -ENOMEM).
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes various reclocking related issues on prime systems.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If the entry size is too small, default to invalid values for both
boost_id and tdp_id, so as to default to the base clock in both cases.
Signed-off-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With instantaneous high precision vblank timestamping
that updates at leading edge of vblank, the emulated
"hw vblank counter" from vblank timestamping, which
increments at leading edge of vblank, and reliable
page flip execution and completion at leading edge of
vblank, we should meet the requirements for fast/
immediate vblank irq disable/enable.
This is only allowed on nv50+ gpu's, ie. the ones with
atomic modesetting. One requirement for immediate vblank
disable is that high precision vblank timestamping works
reliably all the time on all connectors. This is not the
case on all pre-nv50 parts for analog VGA outputs, where we
currently don't always have support for scanout position
queries and therefore fall back to vblank interrupt
timestamping. The implementation in nv04_head_state() does
not return valid values for vblanks, vtotal, hblanks, htotal
for VGA outputs on all cards, but those are needed for scanout
position queries.
Testing on Linux-4.12-rc5 + drm-next on a GeForce 9500 GT
(NV G96) with timing measurement equipment indicates this
works fine, so allow immediate vblank disable for power
saving.
For debugging in case of unexpected trouble, booting
with kernel cmdline option drm.vblankoffdelay=0
(or echo 0 > /sys/module/drm/parameters/vblankoffdelay)
would keep vblank irqs permanently on to approximate old
behavior.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Use drm_*_get() and drm_*_put() helpers instead of drm_*_reference() and
drm_*_unreference() helpers.
Generated by: scripts/coccinelle/api/drm-get-put.cocci
Fixes: 30ed49b55b ("drm/nouveau/kms/nv50-: move code underneath dispnv50/")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Change values to u32, there's no need for them to be 64-bit.
Reported-by: Colin Ian King <colin.king@canonical.com>
Suggested-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows to have the related MODULE_FIRMWARE tag only
on relevant arch (arm64).
This will saves about 400k on initramfs when not relevant
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If softsynthx_read() is called with `count < 3`, `count - 3` wraps, causing
the loop to copy as much data as available to the provided buffer. If
softsynthx_read() is invoked through sys_splice(), this causes an
unbounded kernel write; but even when userspace just reads from it
normally, a small size could cause userspace crashes.
Fixes: 425e586cf9 ("speakup: add unicode variant of /dev/softsynth")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'hostif_mib_set_request_bool' function receives a bool as value and
send the received value with MIB_VALUE_TYPE_BOOL type. There is
one case where the value passed is not a boolean one but
'MCAST_FILTER_PROMISC' which is '2'. Call hostif_mib_set_request_int
instead for related multicast enumeration. This changes original
code behaviour but seems to be the right way to do this.
Fixes: 8ce76bff0e ("staging: ks7010: add new helpers to achieve mib set request and simplify code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b83b8b1881 ("staging:r8188eu: Use lib80211 to support TKIP")
is causing 2 problems for me:
1) One boot the wifi on a laptop with a r8188eu wifi device would not
connect and dmesg contained an oops about scheduling while atomic
pointing to the tkip code. This went away after reverting the commit.
2) I reverted the revert to try and get the oops from 1. again to be able
to add it to this commit message. But now the system did connect to the
wifi only to print a whole bunch of oopses, followed by a hardfreeze a
few seconds later. Subsequent reboots also all lead to scenario 2. Until
I reverted the commit again.
Revert the commit fixes both issues making the laptop usable again.
Fixes: b83b8b1881 ("staging:r8188eu: Use lib80211 to support TKIP")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently nouveau doesn't actually expose the state debugfs file that's
usually provided for any modesetting driver that supports atomic, even
if nouveau is loaded with atomic=1. This is due to the fact that the
standard debugfs files that DRM creates for atomic drivers is called
when drm_get_pci_dev() is called from nouveau_drm.c. This happens well
before we've initialized the display core, which is currently
responsible for setting the DRIVER_ATOMIC cap.
So, move the atomic option into nouveau_drm.c and just add the
DRIVER_ATOMIC cap whenever it's enabled on the kernel commandline. This
shouldn't cause any actual issues, as the atomic ioctl will still fail
as expected even if the display core doesn't disable it until later in
the init sequence. This also provides the added benefit of being able to
use the state debugfs file to check the current display state even if
clients aren't allowed to modify it through anything other than the
legacy ioctls.
Additionally, disable the DRIVER_ATOMIC cap in nv04's display core, as
this was already disabled there previously.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This both uses the legacy modesetting structures in a racy manner, and
additionally also doesn't even check the right variable (enabled != the
CRTC is actually turned on for atomic).
This fixes issues on my P50 regarding the dedicated GPU not entering
runtime suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A CRTC being enabled doesn't mean it's on! It doesn't even necessarily
mean it's being used. This fixes runtime PM leaks on the P50 I've got
next to me.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When MST and atomic were introduced to nouveau, another structure that
could contain a drm_connector embedded within it was introduced; struct
nv50_mstc. This meant that we no longer would be able to simply loop
through our connector list and assume that nouveau_connector() would
return a proper pointer for each connector, since the assertion that
all connectors coming from nouveau have a full nouveau_connector struct
became invalid.
Unfortunately, none of the actual code that looped through connectors
ever got updated, which means that we've been causing invalid memory
accesses for quite a while now.
An example that was caught by KASAN:
[ 201.038698] ==================================================================
[ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718
[ 201.038800]
[ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1
[ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 201.038887] Call Trace:
[ 201.038894] dump_stack+0xa4/0xfd
[ 201.038900] print_address_description+0x71/0x239
[ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038935] kasan_report.cold.6+0x242/0x2fe
[ 201.038942] __asan_report_load4_noabort+0x19/0x20
[ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau]
[ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4
[ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau]
[ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau]
[ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau]
[ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau]
[ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau]
[ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau]
[ 201.039264] pci_pm_runtime_resume+0x130/0x250
[ 201.039269] ? pci_restore_standard_config+0x70/0x70
[ 201.039275] __rpm_callback+0x1f2/0x5d0
[ 201.039279] ? rpm_resume+0x560/0x18a0
[ 201.039283] ? pci_restore_standard_config+0x70/0x70
[ 201.039287] ? pci_restore_standard_config+0x70/0x70
[ 201.039291] ? pci_restore_standard_config+0x70/0x70
[ 201.039296] rpm_callback+0x175/0x210
[ 201.039300] ? pci_restore_standard_config+0x70/0x70
[ 201.039305] rpm_resume+0xcc3/0x18a0
[ 201.039312] ? rpm_callback+0x210/0x210
[ 201.039317] ? __pm_runtime_resume+0x9e/0x100
[ 201.039322] ? kasan_check_write+0x14/0x20
[ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039333] __pm_runtime_resume+0xac/0x100
[ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau]
[ 201.039380] process_one_work+0x7a0/0x14d0
[ 201.039388] ? cancel_delayed_work_sync+0x20/0x20
[ 201.039392] ? lock_acquire+0x113/0x310
[ 201.039398] ? kasan_check_write+0x14/0x20
[ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039409] worker_thread+0x86/0xb50
[ 201.039418] kthread+0x2e9/0x3a0
[ 201.039422] ? process_one_work+0x14d0/0x14d0
[ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 201.039431] ret_from_fork+0x3a/0x50
[ 201.039441]
[ 201.039444] Allocated by task 79:
[ 201.039449] save_stack+0x43/0xd0
[ 201.039452] kasan_kmalloc+0xc4/0xe0
[ 201.039456] kmem_cache_alloc_trace+0x10a/0x260
[ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau]
[ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper]
[ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper]
[ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper]
[ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper]
[ 201.039529] process_one_work+0x7a0/0x14d0
[ 201.039533] worker_thread+0x86/0xb50
[ 201.039537] kthread+0x2e9/0x3a0
[ 201.039541] ret_from_fork+0x3a/0x50
[ 201.039543]
[ 201.039546] Freed by task 0:
[ 201.039549] (stack is not available)
[ 201.039551]
[ 201.039555] The buggy address belongs to the object at ffff88076738c1a8
which belongs to the cache kmalloc-2048 of size 2048
[ 201.039559] The buggy address is located 1192 bytes inside of
2048-byte region [ffff88076738c1a8, ffff88076738c9a8)
[ 201.039563] The buggy address belongs to the page:
[ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0
[ 201.039573] flags: 0x8000000000008100(slab|head)
[ 201.039578] raw: 8000000000008100 ffffea001da3be08 ffffea001da25a08 ffff88084000d0c0
[ 201.039582] raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000
[ 201.039585] page dumped because: kasan: bad access detected
[ 201.039588]
[ 201.039591] Memory state around the buggy address:
[ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 201.039604] ^
[ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039613] ==================================================================
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Every codepath in nouveau that loops through the connector list
currently does so using the old method, which is prone to race
conditions from MST connectors being created and destroyed. This has
been causing a multitude of problems, including memory corruption from
trying to access connectors that have already been freed!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
