changed gvt display transcode DDI mode from DP_SST to
DVI to address below calltrace issue during guest booting
up which is caused by zero dotclock initial value with DP_SST
mode. transcode DVI mode emulation also align with native with DP
connection.
[drm:drm_calc_timestamping_constants]
ERROR crtc 41: Can't calculate constants, dotclock = 0!
WARNING: at drivers/gpu/drm/drm_vblank.c:620
drm_calc_vbltimestamp_from_scanoutpos
Call Trace:
? drm_calc_timestamping_constants+0x144/0x150 [drm]
drm_get_last_vbltimestamp+0x54/0x90 [drm]
drm_reset_vblank_timestamp+0x59/0xd0 [drm]
drm_crtc_vblank_on+0x7b/0xd0 [drm]
intel_modeset_setup_hw_state+0xb67/0xfd0 [i915]
? gen2_read32+0x110/0x110 [i915]
? drm_modeset_lock+0x30/0xa0 [drm]
intel_modeset_init+0x794/0x19d0 [i915]
? intel_setup_gmbus+0x232/0x2e0 [i915]
i915_driver_load+0xb4a/0xf40 [i915]
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
when guest writes ggtt entries, it could write 8 bytes a time if
gtt_entry_size is 8. But, qemu could split the 8 bytes into 2 consecutive
4-byte writes.
If each 4-byte partial write could trigger a host ggtt write, it is very
possible that a wrong combination is written to the host ggtt. E.g.
the higher 4 bytes is the old value, but the lower 4 bytes is the new
value, and this 8-byte combination is wrong but written to the ggtt, thus
causing bugs.
To handle this condition, we just record the first 4-byte write, then wait
until the second 4-byte write comes and write the combined 64-bit data to
host ggtt table.
To save memory space and to spot partial write as early as possible, we
don't keep this information for every ggtt index. Instread, we just record
the last ggtt write position, and assume the two 4-byte writes come in
consecutively for each vgpu.
This assumption is right based on the characteristic of ggtt entry which
stores memory address. When gtt_entry_size is 8, the guest memory physical
address should be 64 bits, so any sane guest driver should write 8-byte
long data at a time, so 2 consecutive 4-byte writes at the same ggtt index
should be trapped in gvt.
v2:
when incomplete ggtt entry write is located, e.g.
1. guest only writes 4 bytes at a ggtt offset and no long writes the
rest 4 bytes.
2. guest writes 4 bytes of a ggtt offset, then write at other ggtt
offsets, then return back to write the left 4 bytes of the first
ggtt offset.
add error handling logic to remap host entry to scratch page, and mark
guest virtual ggtt entry as not present. (zhenyu wang)
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_gem_object. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch unifies the naming of DRM functions for reference counting
of struct drm_framebuffer. The resulting code is more aligned with the
rest of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tdz@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Amritha Nambiar says:
====================
Symmetric queue selection using XPS for Rx queues
This patch series implements support for Tx queue selection based on
Rx queue(s) map. This is done by configuring Rx queue(s) map per Tx-queue
using sysfs attribute. If the user configuration for Rx queues does
not apply, then the Tx queue selection falls back to XPS using CPUs and
finally to hashing.
XPS is refactored to support Tx queue selection based on either the
CPUs map or the Rx-queues map. The config option CONFIG_XPS needs to be
enabled. By default no receive queues are configured for the Tx queue.
- /sys/class/net/<dev>/queues/tx-*/xps_rxqs
A set of receive queues can be mapped to a set of transmit queues (many:many),
although the common use case is a 1:1 mapping. This will enable sending
packets on the same Tx-Rx queue association as this is useful for busy polling
multi-threaded workloads where it is not possible to pin the threads to
a CPU. This is a rework of Sridhar's patch for symmetric queueing via
socket option:
https://www.spinics.net/lists/netdev/msg453106.html
Testing Hints:
Kernel: Linux 4.17.0-rc7+
Interface:
driver: ixgbe
version: 5.1.0-k
firmware-version: 0x00015e0b
Configuration:
ethtool -L $iface combined 16
ethtool -C $iface rx-usecs 1000
sysctl net.core.busy_poll=1000
ATR disabled:
ethtool -K $iface ntuple on
Workload:
Modified memcached that changes the thread selection policy to be based
on the incoming rx-queue of a connection using SO_INCOMING_NAPI_ID socket
option. The default is round-robin.
Default: No rxqs_map configured
Symmetric queues: Enable rxqs_map for all queues 1:1 mapped to Tx queue
System:
Architecture: x86_64
CPU(s): 72
Model name: Intel(R) Xeon(R) CPU E5-2699 v3 @ 2.30GHz
16 threads 400K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 4/51/2215 2/30/5163
(usec)
intr/sec 26655 18606
contextswitch/sec 5145 4044
insn per cycle 0.43 0.72
cache-misses 6.919 4.310
(% of all cache refs)
L1-dcache-load- 4.49 3.29
-misses
(% of all L1-dcache hits)
LLC-load-misses 13.26 8.96
(% of all LL-cache hits)
-------------------------------------------------------------------------------
32 threads 400K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 10/112/5562 9/46/4637
(usec)
intr/sec 30456 27666
contextswitch/sec 7552 5133
insn per cycle 0.41 0.49
cache-misses 9.357 2.769
(% of all cache refs)
L1-dcache-load- 4.09 3.98
-misses
(% of all L1-dcache hits)
LLC-load-misses 12.96 3.96
(% of all LL-cache hits)
-------------------------------------------------------------------------------
16 threads 800K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 5/151/4989 9/69/2611
(usec)
intr/sec 35686 22907
contextswitch/sec 25522 12281
insn per cycle 0.67 0.74
cache-misses 8.652 6.38
(% of all cache refs)
L1-dcache-load- 3.19 2.86
-misses
(% of all L1-dcache hits)
LLC-load-misses 16.53 11.99
(% of all LL-cache hits)
-------------------------------------------------------------------------------
32 threads 800K requests/sec
=============================
-------------------------------------------------------------------------------
Default Symmetric queues
-------------------------------------------------------------------------------
RTT min/avg/max 6/163/6152 8/88/4209
(usec)
intr/sec 47079 26548
contextswitch/sec 42190 39168
insn per cycle 0.45 0.54
cache-misses 8.798 4.668
(% of all cache refs)
L1-dcache-load- 6.55 6.29
-misses
(% of all L1-dcache hits)
LLC-load-misses 13.91 10.44
(% of all LL-cache hits)
-------------------------------------------------------------------------------
v6:
- Changed the names of some functions to begin with net_if.
- Cleaned up sk_tx_queue_set/sk_rx_queue_set functions.
- Added sk_rx_queue_clear to make it consistent with tx_queue_mapping
initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend transmit queue sysfs attribute to configure Rx queue(s) map
per Tx queue. By default no receive queues are configured for the
Tx queue.
- /sys/class/net/eth0/queues/tx-*/xps_rxqs
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'skc_tx_queue_mapping' field in sock_common structure from
'int' to 'unsigned short' type with ~0 indicating unset and
other positive queue values being set. This will accommodate adding
a new 'unsigned short' field in sock_common in the next patch for
rx_queue_mapping.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use static_key for XPS maps to reduce the cost of extra map checks,
similar to how it is used for RPS and RFS. This includes static_key
'xps_needed' for XPS and another for 'xps_rxqs_needed' for XPS using
Rx queues map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor XPS code to support Tx queue selection based on
CPU(s) map or Rx queue(s) map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Booting a ColdFire m68k core with MMU enabled causes a "bad page state"
oops since commit 1d40a5ea01 ("mm: mark pages in use for page tables"):
BUG: Bad page state in process sh pfn:01ce2
page:004fefc8 count:0 mapcount:-1024 mapping:00000000 index:0x0
flags: 0x0()
raw: 00000000 00000000 00000000 fffffbff 00000000 00000100 00000200 00000000
raw: 039c4000
page dumped because: nonzero mapcount
Modules linked in:
CPU: 0 PID: 22 Comm: sh Not tainted 4.17.0-07461-g1d40a5ea01d5 #13
Fix by calling pgtable_page_dtor() in our __pte_free_tlb() code path,
so that the PG_table flag is cleared before we free the pte page.
Note that I had to change the type of pte_free() to be static from
extern. Otherwise you get a lot of warnings like this:
./arch/m68k/include/asm/mcf_pgalloc.h:80:2: warning: ‘pgtable_page_dtor’ is static but used in inline function ‘pte_free’ which is not static
pgtable_page_dtor(page);
^
And making it static is consistent with our use of this in the other
m68k pgalloc definitions of pte_free().
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
CC: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
-----BEGIN PGP SIGNATURE-----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=KWL7
-----END PGP SIGNATURE-----
Merge tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few regression fixes for qgroup rescan status tracking and
the vm_fault_t conversion that mixed up the error values"
* tag 'for-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix mount failure when qgroup rescan is in progress
Btrfs: fix regression in btrfs_page_mkwrite() from vm_fault_t conversion
btrfs: quota: Set rescan progress to (u64)-1 if we hit last leaf
The Nomadik has a variant of the PL110 known as "Color LCD
Controller" LCDC. This variant has the same bit ordering as
the DRM subsystem (in difference from the other variants)
and adds a few bits for the control of 5551, 565 etc in the
control register. Notably it also adds a packed RGB888
24BPP mode.
We add support by detecting this variant and also adding a
small plug-in that will mux the LCDC out if the ASIC happens
to be muxed to the other graphics controller (they are
mutually exclusive).
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184450.25377-1-linus.walleij@linaro.org
Pull vfs fix from Al Viro:
"Followup to procfs-seq_file series this window"
This fixes a memory leak by making sure that proc seq files release any
private data on close. The 'proc_seq_open' has to be properly paired
with 'proc_seq_release' that releases the extra private data.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
proc: add proc_seq_release
Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziQ7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynwZACgjpcPVTEiA0W02s4B/GhmVt1NMeUAnjgeLDzY
yRz6SX18lSmjHqCUXAk1
=/2QW
-----END PGP SIGNATURE-----
Merge tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems"
* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Return an ERR_PTR in ion_map_kernel
staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
iio: buffer: fix the function signature to match implementation
iio: mma8452: Fix ignoring MMA8452_INT_DRDY
iio: tsl2x7x/tsl2772: avoid potential division by zero
iio: pressure: bmp280: fix relative humidity unit
Here are 5 fixes for the tty core and some serial drivers.
The tty core one fix some security and other issues reported by the
syzbot that I have taken too long in responding to (sorry Tetsuo!). The
8350 serial driver fix resolves an issue of devices that used to work
properly stopping working as they shouldn't have been added to a
blacklist.
All of these have been in linux-next for a few days with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziSHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym5LACg0xI1fC7LAKrLSLKglU/H4Wsv6b0AoNIkfbWi
wxAZZKscwFVKNpv6gN9n
=YgAj
-----END PGP SIGNATURE-----
Merge tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five fixes for the tty core and some serial drivers.
The tty core ones fix some security and other issues reported by the
syzbot that I have taken too long in responding to (sorry Tetsuo!).
The 8350 serial driver fix resolves an issue of devices that used to
work properly stopping working as they shouldn't have been added to a
blacklist.
All of these have been in linux-next for a few days with no reported
issues"
* tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: prevent leaking uninitialized data to userspace via /dev/vcs*
serdev: fix memleak on module unload
serial: 8250_pci: Remove stalled entries in blacklist
n_tty: Access echo_* variables carefully.
n_tty: Fix stall at n_tty_receive_char_special().
Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and xhci
host controller fixes for reported issues (as normal), but there are
also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWziS+Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn8QQCfU8PnLo+uPoV+DU7Nm1486mHTP4YAoLU3Q0nE
oRmnzA3TnxytluWgbC7M
=H8MG
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and
xhci host controller fixes for reported issues (as normal), but there
are also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: host: fix disconnection detect issue
usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered
typec: tcpm: Fix a msecs vs jiffies bug
NFC: pn533: Fix wrong GFP flag usage
usb: cdc_acm: Add quirk for Uniden UBC125 scanner
staging/typec: fix tcpci_rt1711h build errors
usb: typec: ucsi: Fix for incorrect status data issue
usb: typec: ucsi: acpi: Workaround for cache mode issue
acpi: Add helper for deactivating memory region
usb: xhci: increase CRS timeout value
usb: xhci: tegra: fix runtime PM error handling
usb: xhci: remove the code build warning
xhci: Fix kernel oops in trace_xhci_free_virt_device
xhci: Fix perceived dead host due to runtime suspend race with event handler
dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation
usb: gadget: dwc2: fix memory leak in gadget_init()
usb: gadget: composite: fix delayed_status race condition when set_interface
usb: dwc2: fix isoc split in transfer with no data
usb: dwc2: alloc dma aligned buffer for isoc split in
usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub
...
Allow UPDSA to change "set mark" to permit
policy separation of packet routing decisions from
SA keying in systems that use mark-based routing.
The set mark, used as a routing and firewall mark
for outbound packets, is made update-able which
allows routing decisions to be handled independently
of keying/SA creation. To maintain consistency with
other optional attributes, the set mark is only
updated if sent with a non-zero value.
The per-SA lock and the xfrm_state_lock are taken in
that order to avoid a deadlock with
xfrm_timer_handler(), which also takes the locks in
that order.
Signed-off-by: Nathan Harold <nharold@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add explicit RETs to the tail calls of AEGIS and MORUS crypto algorithms
otherwise they run into INT3 padding due to
("x86/asm: Pad assembly functions with INT3 instructions")
leading to spurious debug exceptions.
Mike Galbraith <efault@gmx.de> took care of all the remaining callsites.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Ondrej Mosnacek <omosnacek@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Building the kernel with CONFIG_THUMB2_KERNEL=y and
CONFIG_CRYPTO_SPECK_NEON set fails with the following errors:
arch/arm/crypto/speck-neon-core.S: Assembler messages:
arch/arm/crypto/speck-neon-core.S:419: Error: r13 not allowed here -- `bic sp,#0xf'
arch/arm/crypto/speck-neon-core.S:423: Error: r13 not allowed here -- `bic sp,#0xf'
arch/arm/crypto/speck-neon-core.S:427: Error: r13 not allowed here -- `bic sp,#0xf'
arch/arm/crypto/speck-neon-core.S:431: Error: r13 not allowed here -- `bic sp,#0xf'
The problem is that the 'bic' instruction can't operate on the 'sp'
register in Thumb2 mode. Fix it by using a temporary register. This
isn't in the main loop, so the performance difference is negligible.
This also matches what aes-neonbs-core.S does.
Reported-by: Stefan Agner <stefan@agner.ch>
Fixes: ede9622162 ("crypto: arm/speck - add NEON-accelerated implementation of Speck-XTS")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ZII's RDU1s come with up to 3 EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The hog pinctrl hog is meant for pins that do not have an
associated driver.
The MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK pin is the one that
provides the MCLK signal to the SGTL5000 codec, so a
better represenation is to move it under the codec node.
While at it, change the pinctrl value from 0x80000000 to the
POR reset value of register IOMUXC_SW_PAD_CTL_PAD_GPIO_0.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function skcipher_walk_next declared as static and marked as
EXPORT_SYMBOL_GPL. It's a bit confusing for internal function to be
exported. The area of visibility for such function is its .c file
and all other modules. Other *.c files of the same module can't use it,
despite all other modules can. Relying on the fact that this is the
internal function and it's not a crucial part of the API, the patch
just removes the EXPORT_SYMBOL_GPL marking of skcipher_walk_next.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Register a crypto algo with the Linux crypto layer only if
the algorithm is supported by the backend virtio-crypto
device.
Also route crypto requests to a virtio-crypto
device, only if it can support the requested service and
algorithm.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Acked-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Read the crypto services and algorithm masks which provides
information about the services and algorithms supported by
virtio-crypto backend.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Acked-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the original version of the VMAC template that had the nonce
hardcoded to 0 and produced a digest with the wrong endianness. I'm
unsure whether this had users or not (there are no explicit in-kernel
references to it), but given that the hardcoded nonce made it wildly
insecure unless a unique key was used for each message, let's try
removing it and see if anyone complains.
Leave the new "vmac64" template that requires the nonce to be explicitly
specified as the first 16 bytes of data and uses the correct endianness
for the digest.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently the VMAC template uses a "nonce" hardcoded to 0, which makes
it insecure unless a unique key is set for every message. Also, the
endianness of the final digest is wrong: the implementation uses little
endian, but the VMAC specification has it as big endian, as do other
VMAC implementations such as the one in Crypto++.
Add a new VMAC template where the nonce is passed as the first 16 bytes
of data (similar to what is done for Poly1305's nonce), and the digest
is big endian. Call it "vmac64", since the old name of simply "vmac"
didn't clarify whether the implementation is of VMAC-64 or of VMAC-128
(which produce 64-bit and 128-bit digests respectively); so we fix the
naming ambiguity too.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
syzbot reported a crash in vmac_final() when multiple threads
concurrently use the same "vmac(aes)" transform through AF_ALG. The bug
is pretty fundamental: the VMAC template doesn't separate per-request
state from per-tfm (per-key) state like the other hash algorithms do,
but rather stores it all in the tfm context. That's wrong.
Also, vmac_final() incorrectly zeroes most of the state including the
derived keys and cached pseudorandom pad. Therefore, only the first
VMAC invocation with a given key calculates the correct digest.
Fix these bugs by splitting the per-tfm state from the per-request state
and using the proper init/update/final sequencing for requests.
Reproducer for the crash:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int fd;
struct sockaddr_alg addr = {
.salg_type = "hash",
.salg_name = "vmac(aes)",
};
char buf[256] = { 0 };
fd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(fd, (void *)&addr, sizeof(addr));
setsockopt(fd, SOL_ALG, ALG_SET_KEY, buf, 16);
fork();
fd = accept(fd, NULL, NULL);
for (;;)
write(fd, buf, 256);
}
The immediate cause of the crash is that vmac_ctx_t.partial_size exceeds
VMAC_NHBYTES, causing vmac_final() to memset() a negative length.
Reported-by: syzbot+264bca3a6e8d645550d3@syzkaller.appspotmail.com
Fixes: f1939f7c56 ("crypto: vmac - New hash algorithm for intel_txt support")
Cc: <stable@vger.kernel.org> # v2.6.32+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The VMAC template assumes the block cipher has a 128-bit block size, but
it failed to check for that. Thus it was possible to instantiate it
using a 64-bit block size cipher, e.g. "vmac(cast5)", causing
uninitialized memory to be used.
Add the needed check when instantiating the template.
Fixes: f1939f7c56 ("crypto: vmac - New hash algorithm for intel_txt support")
Cc: <stable@vger.kernel.org> # v2.6.32+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If SACK is not enabled and the first cumulative ACK after the RTO
retransmission covers more than the retransmitted skb, a spurious
FRTO undo will trigger (assuming FRTO is enabled for that RTO).
The reason is that any non-retransmitted segment acknowledged will
set FLAG_ORIG_SACK_ACKED in tcp_clean_rtx_queue even if there is
no indication that it would have been delivered for real (the
scoreboard is not kept with TCPCB_SACKED_ACKED bits in the non-SACK
case so the check for that bit won't help like it does with SACK).
Having FLAG_ORIG_SACK_ACKED set results in the spurious FRTO undo
in tcp_process_loss.
We need to use more strict condition for non-SACK case and check
that none of the cumulatively ACKed segments were retransmitted
to prove that progress is due to original transmissions. Only then
keep FLAG_ORIG_SACK_ACKED set, allowing FRTO undo to proceed in
non-SACK case.
(FLAG_ORIG_SACK_ACKED is planned to be renamed to FLAG_ORIG_PROGRESS
to better indicate its purpose but to keep this change minimal, it
will be done in another patch).
Besides burstiness and congestion control violations, this problem
can result in RTO loop: When the loss recovery is prematurely
undoed, only new data will be transmitted (if available) and
the next retransmission can occur only after a new RTO which in case
of multiple losses (that are not for consecutive packets) requires
one RTO per loss to recover.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
