There's a bug in *_encode_bits() in using ~field_multiplier() for
the check whether or not the constant value fits into the field,
this is wrong and clearly ~field_mask() was intended. This was
triggering for me for both constant and non-constant values.
Additionally, make this case actually into an compile error.
Declaring the extern function that will never exist with just a
warning is pointless as then later we'll just get a link error.
While at it, also fix the indentation in those lines I'm touching.
Finally, as suggested by Andy Shevchenko, add some tests and for
that introduce also u8 helpers. The tests don't compile without
the fix, showing that it's necessary.
Fixes: 00b0c9b826 ("Add primitives for manipulating bitfields both in host- and fixed-endian.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function wlc_phy_workarounds_nphy_rev1 is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'wlc_phy_workarounds_nphy_rev1' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9 ("brcmsmac: fix array out-of-bounds access in qm_log10")
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the clang warning of extraneous parentheses, with the
following coccinelle script.
@@
identifier i;
expression e;
statement s;
@@
if (
-(i == e)
+i == e
)
s
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for source MAC address randomization of probe request
frames. Pass addr/mask randomization parameters to firmware.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement net_device_ops::ndo_set_mac_address callback to allow for
setting interface MAC address. Implementation is done through existing
CHANGE_INTF firmware command. All validation is to be done by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM tested working for wlcore with no autosuspend, we can
now enable autosuspend to cut down on enable/disable for interrupts.
Basically we just replace pm_runtime_put() with the autosuspend variants.
Let's use autosuspend delay of 50ms that MMC drivers typically use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have wl12xx_boot() call wl12xx_enable_interrupts() and if we have
wl1271_op_add_interface() call pm_runtime_get_sync() before the interrupts
are enabled. And then we get the following error during boot:
wlcore: ERROR ELP wakeup timeout!
Let's fix this by first checking if we need to boot the firmware. And
only after that call pm_runtime_get_sync() when interrupts are enabled.
And only after that do the check for wl12xx_need_fw_change().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM enabled, we can now use calls to pm_runtime_force_suspend
and pm_runtime_force_resume for enabling elp during suspend when wowlan
is enabled and waking the chip from elp on resume.
Remove the custom API that was used to ensure that the command
that is used to allow ELP during suspend is completed before the system
suspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After enabling runtime PM, if we force hardware reset multiple times with:
# echo 1 > /sys/kernel/debug/ieee80211/phy0/wlcore/start_recovery
We will after few tries get the following error:
wlcore: ERROR timeout waiting for the hardware to complete initialization
And then wlcore is unable to reconnect until after the wlcore related modules
are reloaded.
Let's fix this by moving pm_runtime_put() earlier before we restart the hardware.
And let's use the sync version to make sure we're done before we restart.
Note that we still will get -EBUSY warning from wl12xx_sdio_set_power() but let's
fix that separately once we know exactly why we get the warning.
Reported-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM enabled, we now need to have wlcore enabled longer
until after we're done calling wlcore_cmd_regdomain_config_locked():
scan_complete_work()
wlcore_cmd_regdomain_config_locked()
wlcore_cmd_send_failsafe()
wl12xx_sdio_raw_read()
Note that this is not needed before runtime PM support as the
custom PM code had it's own timer. We have not yet enabled runtime
PM autosuspend for wlcore and this is why this issue now shows up.
Let's fix the issues first before we enable runtime PM autosuspend.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can update wlcore to use PM runtime by adding functions for
wlcore_runtime_suspend() and wlcore_runtime_resume() and replacing
calls to wl1271_ps_elp_wakeup() and wl1271_ps_elp_sleep() with calls
to pm_runtime_get_sync() and pm_runtime_put().
Note that the new wlcore_runtime_suspend() and wlcore_runtime_resume()
functions are based on simplified versions of wl1271_ps_elp_sleep() and
wl1271_ps_elp_wakeup().
We don't want to use the old functions as we can now take advantage of
the runtime PM usage count. And we don't need the old elp_work at all.
And we can also remove WL1271_FLAG_ELP_REQUESTED that is no longer needed.
Pretty much the only place where we are not just converting the existing
functions is wl1271_op_suspend() where we add pm_runtime_put_noidle()
to keep the calls paired.
As the next step is to implement runtime PM autosuspend, let's not add
wrapper functions for the generic runtime PM calls. We would be getting
rid of any wrapper functions anyways.
After autoidle we should be able to start using Linux generic wakeirqs
for the padconf interrupt.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to wl1271_ps_elp_wakeup() in wl12xx_queue_recovery_work() is
unpaired. Let's remove it and add paired calls to wl1271_recovery_work()
instead in preparation for changing things to use runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Otherwise we can get:
WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84
I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It may not be the actual real stable mailing list address, but the
stable scripts to actually pick up on the traditional way to mark stable
patches.
There are also reasons to explicitly avoid using the actual mailing list
address, since security patches with embargo dates generally do want the
stable marking, but don't want tools etc to mistakenly send the patch
out to the mailing list early.
So don't warn for things that are still actively used and explicitly
supported.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ought to be an omission in e619492323 ("esp: Fix memleaks on error
paths."). The memleak on error path in esp6_input is similar to esp_input
of esp4.
Fixes: e619492323 ("esp: Fix memleaks on error paths.")
Fixes: 3f29770723 ("ipsec: check return value of skb_to_sgvec always")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
R-Car E3 does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: 913a78b575 ("arm64: dts: renesas: r8a77990: Add EthernetAVB device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit cad160ed0a ("ARM: shmobile: Convert file to use
cntvoff"), there's no non-SMP code left in headsmp-apmu.S.
Hence build the file for SMP only, and drop the no longer needed check
for CONFIG_SMP inside the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With CONFIG_RC_CORE=m and VIDEO_CX231XX=y, we get a link failure:
drivers/media/usb/cx231xx/cx231xx-input.o: In function `cx231xx_ir_init':
cx231xx-input.c:(.text+0xd4): undefined reference to `rc_allocate_device'
This narrows down the dependency so that only valid configurations
are allowed.
Fixes: 84545d2a14 ("media: cx231xx: Remove RC_CORE dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Renesas Fine Display Processor driver is used on Renesas R-Car SoCs
only. Since commit 9b5ba0df4e ("ARM: shmobile: Introduce
ARCH_RENESAS") is ARCH_RENESAS a more appropriate platform dependency
than the legacy ARCH_SHMOBILE, hence use the former.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch fixes wrong name of headphone widget for receiving events
of insert/remove headphone plug from simple-card or audio-graph-card.
If we use wrong widget name then we get warning messages such as
"asoc-audio-graph-card sound: ASoC: DAPM unknown pin Headphones"
when the plug is inserted or removed from headphone jack.
Fixes: fb21a0acaa ("arm64: dts: uniphier: add sound node")
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The goal of passing the "quiet" option to the kernel is for the kernel
to be quiet unless something really is wrong.
Sofar passing quiet has been (mostly) equivalent to passing
loglevel=4 on the kernel commandline. Which means to show any messages
with a level of KERN_ERR or higher severity on the console.
In practice this often does not result in a quiet boot though, since
there are many false-positive or otherwise harmless error messages printed,
defeating the purpose of the quiet option. Esp. the ACPICA code is really
bad wrt this, but there are plenty of others too.
This commit makes CONSOLE_LOGLEVEL_QUIET configurable.
This for example will allow distros which want quiet to really mean quiet
to set CONSOLE_LOGLEVEL_QUIET so that only messages with a higher severity
then KERN_ERR (CRIT, ALERT, EMERG) get printed, avoiding an endless game
of whack-a-mole silencing harmless error messages.
Link: http://lkml.kernel.org/r/20180619115726.3098-1-hdegoede@redhat.com
To: Petr Mladek <pmladek@suse.com>
To: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
This patch make sure printing of log on console if loglevel
at time of storing log is less than current console loglevel.
@why
In SMP printk can work asynchronously, logs can be missed on console
because it checks current log level at time of console_unlock,
not at time of storing logs.
func()
{
....
....
console_verbose(); // user wants to have all the logs on console.
pr_alert();
dump_backtrace(); //prints with default loglevel.
...
console_silent(); // stop all logs from printing on console.
}
Now if console_lock was owned by another process, the messages might
be handled after the consoles were silenced.
Reused flag LOG_NOCONS as its usage is gone long back by the commit
5c2992ee7f ("printk: remove console flushing special cases
for partial buffered lines").
Note that there are still some corner cases where this patch is not enough.
For example, when the messages are flushed later from printk_safe buffers
or when there are races between console_verbose() and console_silent()
callers.
Link: http://lkml.kernel.org/r/20180601090029epcas5p3cc93d4bfbebb3199f0a2684058da7e26~z-a_jkmrI2993329933epcas5p3q@epcas5p3.samsung.com
Cc: linux-kernel@vger.kernel.org
Cc: a.sahrawat@samsung.com
Cc: pankaj.m@samsung.com
Cc: v.narang@samsung.com
Cc: <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Since commit 48231f289e ("media: rc: drivers should produce alternate
pulse and space timing events"), on meson-ir we are regularly producing
errors. Reduce to warning level and only warn once to avoid flooding
the log.
A proper fix for meson-ir is going to be too large for v4.18.
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org # 4.17+
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cadence media drivers can be built-in while the v4l2 core is a loadable
module. This is a mistake and leads to link errors:
drivers/media/v4l2-core/v4l2-fwnode.o: In function `v4l2_async_register_subdev_sensor_common':
v4l2-fwnode.c:(.text+0x12f0): undefined reference to `v4l2_async_subdev_notifier_register'
v4l2-fwnode.c:(.text+0x1304): undefined reference to `v4l2_async_register_subdev'
v4l2-fwnode.c:(.text+0x1318): undefined reference to `v4l2_async_notifier_unregister'
v4l2-fwnode.c:(.text+0x1338): undefined reference to `v4l2_async_notifier_cleanup'
cdns-csi2rx.c:(.text+0x9f8): undefined reference to `v4l2_subdev_init'
cdns-csi2rx.c:(.text+0xa78): undefined reference to `v4l2_async_register_subdev'
drivers/media/platform/cadence/cdns-csi2tx.o: In function `csi2tx_remove':
cdns-csi2tx.c:(.text+0x88): undefined reference to `v4l2_async_unregister_subdev'
drivers/media/platform/cadence/cdns-csi2tx.o: In function `csi2tx_probe':
cdns-csi2tx.c:(.text+0x884): undefined reference to `v4l2_subdev_init'
cdns-csi2tx.c:(.text+0xa9c): undefined reference to `v4l2_async_register_subdev'
An explicit Kconfig dependency on VIDEO_V4L2 avoids the problem.
Fixes: 1fc3b37f34 ("media: v4l: cadence: Add Cadence MIPI-CSI2 RX driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I ran into a randconfig build error with the new driver:
drivers/media/platform/cadence/cdns-csi2tx.c: In function 'csi2tx_probe':
drivers/media/platform/cadence/cdns-csi2tx.c:477:11: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc() is declared in linux/slab.h, so let's include this to make it
build in all configurations.
Fixes: 84b477e6d4bc ("media: v4l: cadence: Add Cadence MIPI-CSI2 TX driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver only supports streaming images flipped horizontally and
vertically. In order to ensure that all current users will be fine if or
when support for upright streaming is added, require the presence of the
"rotation" control now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: "Lai, Jim" <jim.lai@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Russell King reported:
"When removing and reloading the etnaviv module, the following splat
occurs:
sysfs: cannot create duplicate filename '/devices/platform/etnaviv'
CPU: 0 PID: 1471 Comm: modprobe Not tainted 4.17.0+ #1608
Hardware name: Marvell Dove (Cubox)
Backtrace:
[<c00157d4>] (dump_backtrace) from [<c0015b8c>] (show_stack+0x18/0x1c)
r6:ef033e38 r5:ee07b340 r4:edb9d000 r3:00000000
[<c0015b74>] (show_stack) from [<c0620784>] (dump_stack+0x20/0x28)
[<c0620764>] (dump_stack) from [<c01bcd24>] (sysfs_warn_dup+0x5c/0x70)
[<c01bccc8>] (sysfs_warn_dup) from [<c01bce14>] (sysfs_create_dir_ns+0x90/0x98)
..."
Commit 246774d17f ("drm/etnaviv: remove the need for a gpu-subsystem
DT node") introduced DRM registration via
platform_device_register_simple(), but missed to call
platform_device_unregister() inside etnaviv_exit().
Fix the problem by calling platform_device_unregister() inside
etnaviv_exit(). While at it, also rearrange the function calls
in the exit path to make them happen in the opposite order of
registration.
Tested on a imx6-sabresd board.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17f ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
platform_device_register_simple() may fail, so we should better
check its return value and propagate it in the case of error.
Cc: <stable@vger.kernel.org>
Fixes: 246774d17f ("drm/etnaviv: remove the need for a gpu-subsystem DT node")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.
As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.
Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO
v2:
- Rebase on drm-tip after prep patch for this was merged there as
requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)
v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency
v4:
- Rebase
v5:
- Detach AUX power wells from the INIT power domain. These power wells
can only be enabled in a TC/TBT connected state and otherwise not
needed during driver initialization.
v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
Fix checkpatch warnings.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com
Discards issued to a DM thin device can complete to userspace (via
fstrim) _before_ the metadata changes associated with the discards is
reflected in the thinp superblock (e.g. free blocks). As such, if a
user constructs a test that loops repeatedly over these steps, block
allocation can fail due to discards not having completed yet:
1) fill thin device via filesystem file
2) remove file
3) fstrim
From initial report, here:
https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html
"The root cause of this issue is that dm-thin will first remove
mapping and increase corresponding blocks' reference count to prevent
them from being reused before DISCARD bios get processed by the
underlying layers. However. increasing blocks' reference count could
also increase the nr_allocated_this_transaction in struct sm_disk
which makes smd->old_ll.nr_allocated +
smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks.
In this case, alloc_data_block() will never commit metadata to reset
the begin pointer of struct sm_disk, because sm_disk_get_nr_free()
always return an underflow value."
While there is room for improvement to the space-map accounting that
thinp is making use of: the reality is this test is inherently racey and
will result in the previous iteration's fstrim's discard(s) completing
vs concurrent block allocation, via dd, in the next iteration of the
loop.
No amount of space map accounting improvements will be able to allow
user's to use a block before a discard of that block has completed.
So the best we can really do is allow DM thinp to gracefully handle such
aggressive use of all the pool's data by degrading the pool into
out-of-data-space (OODS) mode. We _should_ get that behaviour already
(if space map accounting didn't falsely cause alloc_data_block() to
believe free space was available).. but short of that we handle the
current reality that dm_pool_alloc_data_block() can return -ENOSPC.
Reported-by: Dennis Yang <dennisyang@qnap.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The intc #interrupt-cells is equal to 1. Currently gpio
node has 2 cells per IRQ which is wrong. Remove the additional
cell for each of the interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 2e38b946dc ("ARM: davinci: da850: add GPIO DT node")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
- Remove 'nx_warning' and 'smep_warning', which are just pointless obfuscation.
- Also convert to pr_crit().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180627090715.28076-1-dvyukov@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
get_seconds() is deprecated because of the y2038 overflow, so users
should migrate to 64-bit timestamps using ktime_get_real_seconds().
In ext2, the timestamps in the superblock and in the inode are all
limited to 32-bit, and this won't get fixed, so let's just stop
using the deprecated interface and keep truncating.
All users of ext2 should migrate to ext4 before 2038 to prevent this
from causing problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jan Kara <jack@suse.cz>
The VFS structures are finally converted to always use 64-bit timestamps,
and this file system can represent a long range of on-disk timestamps
already, so now let's fit in the missing bits for udf.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Factor out helpers fanotify_add_mark() and fanotify_remove_mark()
to reduce duplicated code.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Use a helper to get the mask from the object (i.e. i_fsnotify_mask)
to generalize code of add/remove inode/vfsmount mark.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Make the code to attach/detach a connector to object more generic
by letting the fsnotify connector point to an abstract fsnotify_connp_t.
Code that needs to dereference an inode or mount object now uses the
helpers fsnotify_conn_{inode,mount}.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Instead of passing inode and vfsmount arguments to fsnotify_add_mark()
and its _locked variant, pass an abstract object pointer and the object
type.
The helpers fsnotify_obj_{inode,mount} are added to get the concrete
object pointer from abstract object pointer.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The object marks manipulation functions fsnotify_destroy_marks()
fsnotify_find_mark() and their helpers take an argument of type
struct fsnotify_mark_connector __rcu ** to dereference the connector
pointer. use a typedef to describe this type for brevity.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Add the tas5707 to the available compatibles of the tas571x driver
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add simple-audio-amplifier to the list of available compatible
Suggested-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is simple enough that we can make it a generic component.
Just rename and sed the dio2125 amplifier driver to simple_amplifier.
Suggested-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
