Fix to return error code -ENODEV from the get device failed error
handling case instead of 0, as done elsewhere in this function.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add ONFI_FEATURE_ON_DIE_ECC to the set/get features list for Micron
NAND flash.
Fixes: 789157e41a ("mtd: rawnand: allow vendors to declare (un)supported features")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add device remove and module exit code to make the driver
functioning as a loadable module.
Fixes: ac28927659 (cpufreq: kryo: allow building as a loadable module)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In event of error returned by the nvmem_cell_read() non-pointer value
may be dereferenced. Fix this with error handling.
Additionally free the allocated speedbin buffer, as per the API.
Fixes: 9ce36edd1a52 (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds new psrwake options defined in the below table.
Platform PSR wake options vbt version
KBL/CFL/WHL All(205+)
BXT Uses old interpretation.
CNL/ICL+ All(205+)
GLK All(205+)
SKL All PV releases (Check for 205+ might help but cannot be foolproof)
We will continue with newer interpretation for SKL from 205.
v2: Jani
Keep the bdb version check.
v3:
Apply newer version for skl from 205+(DK).
Add (version check && platform list) (Jani).
Add bdb version for each platform in commit message(DK).
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Puthikorn Voravootivat <puthik@chromium.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ashutosh D Shukla <ashutosh.d.shukla@intel.com>
Cc: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1529302326-3567-1-git-send-email-vathsala.nagaraju@intel.com
This patch adds the clock used by the CryptoCell 630p instance in the
SoC.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CR core clock, which is used by the Secure Engine (SCEG).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Gilad Ben-Yossef <gilad@benyossef.com>
get_monotonic_boottime() is deprecated because it uses the old 'timespec'
structure. This replaces one of the last callers with a call to
ktime_get_boottime.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: y2038@lists.linaro.org
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Link: https://lkml.kernel.org/r/20180618150114.849216-1-arnd@arndb.de
Some of the oddly named time accessor functions now have a more consistent
naming, which should be used from now on so the aliases can be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: y2038@lists.linaro.org
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Link: https://lkml.kernel.org/r/20180618143246.3865099-1-arnd@arndb.de
The two do the same, this moves all users to the newer name for consistency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: y2038@lists.linaro.org
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Link: https://lkml.kernel.org/r/20180618140811.2998503-3-arnd@arndb.de
Both get_seconds() and do_gettimeofday() are deprecated. Change the time()
implementation to use the replacement function instead.
Obviously the system call will still overflow in 2038, but this gets us
closer to removing the old helper functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: y2038@lists.linaro.org
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20180618140811.2998503-2-arnd@arndb.de
Fix build error on nds32 due to the merge of commit e3d5980568 ("lib:
Rename compiler intrinsic selects to GENERIC_LIB_*") during the 4.18
merge window which renames Kconfig symbols. This had raced with commit
aeaa7af744 ("nds32: lib: To use generic lib instead of libgcc to
prevent the symbol undefined issue.") merged late in the 4.17 cycle,
which added selects to nds32 using the original Kconfig symbol names.
When they came together in merge commit 763f96944c ("Merge tag
'mips_4.18' of
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux") this resulted
in the following build errors:
nds32le-linux-ld: kernel/time/timekeeping.o: in function `timekeeping_init':
timekeeping.c:(.init.text+0x140): undefined reference to `__ashldi3'
nds32le-linux-ld: timekeeping.c:(.init.text+0x144): undefined reference to `__ashldi3'
nds32le-linux-ld: timekeeping.c:(.init.text+0x17e): undefined reference to `__lshrdi3'
nds32le-linux-ld: timekeeping.c:(.init.text+0x182): undefined reference to `__lshrdi3'
nds32le-linux-ld: drivers/clocksource/mmio.o: in function `clocksource_mmio_init':
mmio.c:(.init.text+0x54): undefined reference to `__lshrdi3'
nds32le-linux-ld: mmio.c:(.init.text+0x58): undefined reference to `__lshrdi3'
Rename all 6 selects in nds32 and adjust the ordering accordingly to be
alphabetical.
Fixes: 763f96944c ("Merge tag 'mips_4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[jhogan@kernel.org: Rename all 6 symbols, sort, update commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
nds32 depends on the macros '__NDS32_E[BL]__' to correctly
select or define endian-specific macros, structures or pieces
of code.
These macros are predefined by the compiler but sparse knows nothing
about them and thus may pre-process files differently from what
GCC would.
Fix this by adding '-D__NDS32_E[BL]__' to CHECKFLAGS.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Commit b5793b0d92 added support for building the nanosleep compat system
call on 32-bit architectures, but missed one change in nanosleep_copyout(),
which would trigger a BUG() as soon as any architecture is switched over to
use it.
Use the proper config symbol to enable the code path.
Fixes: Commit b5793b0d92 ("posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: y2038@lists.linaro.org
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Link: https://lkml.kernel.org/r/20180618140811.2998503-1-arnd@arndb.de
When the comment was reflowed to a wider format, the "*" snuck in.
Fixes: ae88a23b32 ("irq: refactor and clean up the free_irq() code flow")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20180617124018.25539-1-j.neuschaefer@gmx.net
Jeremy Dorfman identified mutex contention when multiple threads
parse /proc/stat concurrently.
Since commit 425a5072dc ("genirq: Free irq_desc with rcu"),
kstat_irqs_usr() can be switched to rcu locking, which removes this mutex
contention.
show_interrupts() case will be handled in a separate patch.
Reported-by: Jeremy Dorfman <jdorfman@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Link: https://lkml.kernel.org/r/20180618125612.155057-1-edumazet@google.com
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I'm no longer with QCOM. I am still interested in maintaining or reviewing
PCI/DMA engine patches. Update email-id to an active one.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It seems that starting with Skylake Xeon, channel reset clears the
completion address register. Make sure the completion address register is
set again after reset.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 0198d7bb8a ("ASoC: omap-mcbsp: Convert to use the sdma-pcm
instead of omap-pcm") resulted in broken audio playback on OMAP1510
(discovered on Amstrad Delta).
When running on OMAP1510, omap-pcm used to obtain DMA offset from
snd_dmaengine_pcm_pointer_no_residue() based on DMA interrupt triggered
software calculations instead of snd_dmaengine_pcm_pointer() which
depended on residue value calculated from omap_dma_get_src_pos().
Similar code path is still available in now used
sound/soc/soc-generic-dmaengine-pcm.c but it is not triggered.
It was verified already before that omap_get_dma_src_pos() from
arch/arm/plat-omap/dma.c didn't work correctly for OMAP1510 - see
commit 1bdd741991 ("ASoC: OMAP: fix OMAP1510 broken PCM pointer
callback") for details. Apparently the same applies to its successor,
omap_dma_get_src_pos() from drivers/dma/ti/omap-dma.c.
On the other hand, snd_dmaengine_pcm_pointer_no_residue() is described
as depreciated and discouraged for use in new drivers because of its
unreliable accuracy. However, it seems the only working option for
OPAM1510 now, as long as a software calculated residue is not
implemented as OMAP1510 fallback in omap-dma.
Using snd_dmaengine_pcm_pointer_no_residue() code path instead of
snd_dmaengine_pcm_pointer() in sound/soc/soc-generic-dmaengine-pcm.c
can be triggered in two ways:
- by passing pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE from
sound/soc/omap/sdma-pcm.c,
- by passing dma_caps.residue_granularity =
DMA_RESIDUE_GRANULARITY_DESCRIPTOR from DMA engine.
Let's do the latter.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace license text with corresponding SPDX identifiers and update the
format of existing SPDX identifiers to follow the new guideline
Documentation/process/license-rules.rst.
Note that some of the files mentioned X11 license previously but the
license text actually matches MIT license.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two different regulators are defined with the same name and label but
distinct properties.
The first definition was added with the first board dts and the second
was added when upstream added flexcan support.
Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.
The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer
Added under i2cmux/i2c@1 because they're not otherwise accessible.
These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452
Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.
This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 80c49563e2 ("scsi: scsi_debug: implement IMMED bit") there
are long delays in F_SYNC_DELAY and F_SSU_DELAY. This can cause a memory
leak in schedule_resp(), which can be invoked while unloading the
scsi_debug module: free_all_queued() had already freed all sd_dp and
schedule_resp will alloc a new one, which will never get freed. Here's the
kmemleak report while running xfstests generic/350:
unreferenced object 0xffff88007d752b00 (size 128):
comm "rmmod", pid 26940, jiffies 4295816945 (age 7.588s)
hex dump (first 32 bytes):
00 2b 75 7d 00 88 ff ff 00 00 00 00 00 00 00 00 .+u}............
00 00 00 00 00 00 00 00 8e 31 a2 34 5f 03 00 00 .........1.4_...
backtrace:
[<000000002abd83d0>] 0xffffffffa000705e
[<000000004c063fda>] scsi_dispatch_cmd+0xc7/0x1a0
[<000000000c119a00>] scsi_request_fn+0x251/0x550
[<000000009de0c736>] __blk_run_queue+0x3f/0x60
[<000000001c4453c8>] blk_execute_rq_nowait+0x98/0xd0
[<00000000d17ec79f>] blk_execute_rq+0x3a/0x50
[<00000000a7654b6e>] scsi_execute+0x113/0x250
[<00000000fd78f7cd>] sd_sync_cache+0x95/0x160
[<0000000024dacb14>] sd_shutdown+0x9b/0xd0
[<00000000e9101710>] sd_remove+0x5f/0xb0
[<00000000c43f0d63>] device_release_driver_internal+0x13c/0x1f0
[<00000000e8ad57b6>] bus_remove_device+0xe9/0x160
[<00000000713a7b8a>] device_del+0x120/0x320
[<00000000e5db670c>] __scsi_remove_device+0x115/0x150
[<00000000eccbef30>] scsi_forget_host+0x20/0x60
[<00000000cd5a0738>] scsi_remove_host+0x6d/0x120
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
i.MX6SLL supports ARM power off in cpu idle, better to reuse
i.MX6SX cpu idle driver instead of i.MX6SL which does NOT
support ARM power off.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL supports cpu idle with ARM power gated,
it can reuse i.MX6SX's cpu idle driver to support
below 3 states of cpu idle:
state0: WFI;
state1: WAIT mode with ARM power on;
state2: WAIT mode with ARM power off.
L2_PGE in GPC_CNTR needs to be cleared to support
state2 cpu idle.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some platforms like i.MX6UL/i.MX6SLL have L2
page power control in GPC, it needs to be
disabled if ARM is power gated and L2 is NOT
flushed, add GPC interface to control it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Firmware provides drive specific target reset and task abort timeout
values. Driver needs to use these timeout values during task management
calls. If FW does not provide these values, fall back to using earlier
default timeout of 50 seconds for TM.
[mkp: clarified comment]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While driver is waiting for adapter to become operational, if a kill
adapter is issued, driver can bail out from the wait loop immediately
rather than waiting for the entire 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If MR_DCMD_CTRL_GET_INFO DCMD timed out, return failure rather than doing
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to "26.100.00.00"
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Presently driver is using combined reply queue feature when MSI-x vectors >
8 for both SAS3 and SAS3.5 controllers. But as per MPI-spec,
1. For SAS3 controllers, driver should use combined reply queue when HBA
supports more than 8 MSI-x vectors.
2. For SAS3.5 controllers, driver should use combined reply queue when HBA
supports more than 16 MSI-x vectors.
Modified driver code to use combined reply queue for SAS3 controllers when
HBA supports > 8 MSI-x vectors and for SAS3.5 controllers when HBA supports
> 16 MSI-x vectors.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an ioctl is sent to FW, and if there is a controller reset issued
before ioctl gets completed, then in controller reset path all the pending
ioctl commands are terminated from "mpt3sas_ctl_reset_handler" function.
This will wake up the waiting ioctl commands in ioctl path and print
timeouts which are actually not timeouts.
Introduced "mpt3sas_base_check_cmd_timeout" function to check and print
whether command got timed out (or) terminated due to Host reset.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While configuring of NVMe device handling, _pcie_device structure member
was accessed after its reference count is decremented/put. Hence modified
code to access member of _pcie_device structure before its reference count
is decremented/put.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_scan_finished driver should mark port_enable_cmd.status as
'command not used', instead base_cmds.status was marked as 'command not
used'. Update code to mark port_enable_cmd.status as 'command not used'.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux driver when receives Broadcast Asynchronous Event Notification (BAEN)
from the controller firmware, checks all pending I/Os at the driver level
and issues query task, abort task TMs. This is done in the driver to handle
drives which are connected with multiple initiators and undergoing target
resets. In the BAEN handling code, the I/Os issued to NVMe drives are also
handled and query task and abort task TMs are issued, which are not
necessary as there is no multi-initiator and no BAEN concept with NVMe
drives. Hence when the driver checks for pending I/Os it skips NVMe drives
at this moment.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the TCMU_RING_SIZE macro is not using here will discard it and at the
same time clean up the code style.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch reverts changes done in qlt_schedule_sess_for_deletion() to
avoid spinlock recursion sess->vha->work_lock should be used instead
of ha->tgt.sess_lock, that can be locked in callers: qlt_reset() or
qlt_handle_login()
[mkp: roll in build warning reported by sfr]
Fixes: 1c6cacf4ea ("scsi: qla2xxx: Fixup locking for session deletion")
Cc: <stable@vger.kernel.org> #v4.17
Signed-off-by: Mikhail Malygin <m.malygin@yadro.com>
Reported-by: Mikhail Malygin <m.malygin@yadro.com>
Tested-by: Mikhail Malygin <m.malygin@yadro.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver does both wmb() and writel(). The latter already has a barrier
on some architectures like arm64. This ends up with CPU observing two
barriers back to back before executing the register write.
Drivers should generally assume that the barrier implied by writel() is
sufficient for ordering DMA. Remove the extraneous wmb() before it.
[mkp: Squashed Arnd's and Sinan's patches]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Generally target core and TCMUser seem to work fine for tape devices and
media changers. But there is at least one situation where TCMUser is not
able to support sequential access device emulation correctly.
The situation is when an initiator sends a SCSI READ CDB with a length that
is greater than the length of the tape block to read. We can distinguish
two subcases:
A) The initiator sent the READ CDB with the SILI bit being set.
In this case the sequential access device has to transfer the data from
the tape block (only the length of the tape block) and transmit a good
status. The current interface between TCMUser and the userspace does
not support reduction of the read data size by the userspace program.
The patch below fixes this subcase by allowing the userspace program to
specify a reduced data size in read direction.
B) The initiator sent the READ CDB with the SILI bit not being set.
In this case the sequential access device has to transfer the data from
the tape block as in A), but additionally has to transmit CHECK
CONDITION with the ILI bit set and NO SENSE in the sensebytes. The
information field in the sensebytes must contain the residual count.
With the below patch a user space program can specify the real read data
length and appropriate sensebytes. TCMUser then uses the se_cmd flag
SCF_TREAT_READ_AS_NORMAL, to force target core to transmit the real data
size and the sensebytes. Note: the flag SCF_TREAT_READ_AS_NORMAL is
introduced by Lee Duncan's patch "[PATCH v4] target: transport should
handle st FM/EOM/ILI reads" from Tue, 15 May 2018 18:25:24 -0700.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>