Currently, each representor netdev use their own hash table to keep
the mapping from TC flow (f->cookie) to the driver offloaded instance.
The table is the one which originally was added for offloading TC NIC
(not eswitch) rules.
This scheme breaks when the core TC code calls us to add the same flow
twice, (e.g under egdev use case) since we don't spot that and offload
a 2nd flow into the HW with the wrong source vport.
As a pre-step to solve that, we move to use a single table which keeps
all offloaded TC eswitch flows. The table is located at the eswitch
uplink representor object.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is a refactoring step to be able and store the hash table which
keeps track of offloaded TC flows in a different location for NIC
vs e-switch rules.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an e-switch TC rule is offloaded through the egdev (egress
device) mechanism, we treat this as egress, all other cases (NIC
and e-switch) are considred ingress.
This is preparation step that will allow us to identify "wrong"
stat/del offload calls made by the TC core on egdev based flows and
ignore them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the merged eswitch capability is supported, allow offloading rules
between VFs which belong to different PFs (and hence have different
eswitch affinity).
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patches to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fixes: 2cd1f0ddbb ("isdn: replace ->proc_fops with ->proc_show")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Recently during testing, I ran into the following panic:
[ 207.892422] Internal error: Accessing user space memory outside uaccess.h routines: 96000004 [#1] SMP
[ 207.901637] Modules linked in: binfmt_misc [...]
[ 207.966530] CPU: 45 PID: 2256 Comm: test_verifier Tainted: G W 4.17.0-rc3+ #7
[ 207.974956] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
[ 207.982428] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 207.987214] pc : bpf_skb_load_helper_8_no_cache+0x34/0xc0
[ 207.992603] lr : 0xffff000000bdb754
[ 207.996080] sp : ffff000013703ca0
[ 207.999384] x29: ffff000013703ca0 x28: 0000000000000001
[ 208.004688] x27: 0000000000000001 x26: 0000000000000000
[ 208.009992] x25: ffff000013703ce0 x24: ffff800fb4afcb00
[ 208.015295] x23: ffff00007d2f5038 x22: ffff00007d2f5000
[ 208.020599] x21: fffffffffeff2a6f x20: 000000000000000a
[ 208.025903] x19: ffff000009578000 x18: 0000000000000a03
[ 208.031206] x17: 0000000000000000 x16: 0000000000000000
[ 208.036510] x15: 0000ffff9de83000 x14: 0000000000000000
[ 208.041813] x13: 0000000000000000 x12: 0000000000000000
[ 208.047116] x11: 0000000000000001 x10: ffff0000089e7f18
[ 208.052419] x9 : fffffffffeff2a6f x8 : 0000000000000000
[ 208.057723] x7 : 000000000000000a x6 : 00280c6160000000
[ 208.063026] x5 : 0000000000000018 x4 : 0000000000007db6
[ 208.068329] x3 : 000000000008647a x2 : 19868179b1484500
[ 208.073632] x1 : 0000000000000000 x0 : ffff000009578c08
[ 208.078938] Process test_verifier (pid: 2256, stack limit = 0x0000000049ca7974)
[ 208.086235] Call trace:
[ 208.088672] bpf_skb_load_helper_8_no_cache+0x34/0xc0
[ 208.093713] 0xffff000000bdb754
[ 208.096845] bpf_test_run+0x78/0xf8
[ 208.100324] bpf_prog_test_run_skb+0x148/0x230
[ 208.104758] sys_bpf+0x314/0x1198
[ 208.108064] el0_svc_naked+0x30/0x34
[ 208.111632] Code: 91302260 f9400001 f9001fa1 d2800001 (29500680)
[ 208.117717] ---[ end trace 263cb8a59b5bf29f ]---
The program itself which caused this had a long jump over the whole
instruction sequence where all of the inner instructions required
heavy expansions into multiple BPF instructions. Additionally, I also
had BPF hardening enabled which requires once more rewrites of all
constant values in order to blind them. Each time we rewrite insns,
bpf_adj_branches() would need to potentially adjust branch targets
which cross the patchlet boundary to accommodate for the additional
delta. Eventually that lead to the case where the target offset could
not fit into insn->off's upper 0x7fff limit anymore where then offset
wraps around becoming negative (in s16 universe), or vice versa
depending on the jump direction.
Therefore it becomes necessary to detect and reject any such occasions
in a generic way for native eBPF and cBPF to eBPF migrations. For
the latter we can simply check bounds in the bpf_convert_filter()'s
BPF_EMIT_JMP helper macro and bail out once we surpass limits. The
bpf_patch_insn_single() for native eBPF (and cBPF to eBPF in case
of subsequent hardening) is a bit more complex in that we need to
detect such truncations before hitting the bpf_prog_realloc(). Thus
the latter is split into an extra pass to probe problematic offsets
on the original program in order to fail early. With that in place
and carefully tested I no longer hit the panic and the rewrites are
rejected properly. The above example panic I've seen on bpf-next,
though the issue itself is generic in that a guard against this issue
in bpf seems more appropriate in this case.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fix race condition when accessing System Management Network registers
Fix reading critical temperatures on F15h M60h and M70h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SujR
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two k10temp fixes:
- fix race condition when accessing System Management Network
registers
- fix reading critical temperatures on F15h M60h and M70h
Also add PCI ID's for the AMD Raven Ridge root bridge"
* tag 'hwmon-for-linus-v4.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Use API function to access System Management Network
x86/amd_nb: Add support for Raven Ridge CPUs
hwmon: (k10temp) Fix reading critical temperature register
For all platforms that run haswell_crtc_enable, our spec tells us to
configure the transcoder clocks and do link training before it tells
us to set pipeconf and the other pipe/transcoder/plane registers.
Starting from Icelake, we get machine hangs if we try to touch the
pipe/transcoder registers without having the clocks configured and not
having some chicken bits set. So this patch changes
haswell_crtc_enable() to issue the calls at the appropriate order
mandated by the spec.
While setting the appropriate chicken bits would also work here, it's
better if we actually program the hardware the way it is intended to
be programmed. And the chicken bit also has some theoretical downsides
that may or may not affect us. Also, correctly programming the
hardware does not prevent us from setting the chicken bits in a later
patch in case we decide to.
v2: Don't forget link training (Ville).
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502215851.30736-1-paulo.r.zanoni@intel.com
Stop reading some now deprecated interrupt registers in both
debugfs and error state. Instead, read the new equivalents in the
Gen11 interrupt repartitioning scheme.
Note that the equivalent to the PM ISR & IIR cannot be read without
affecting the current state of the system, so I've opted for leaving
them out. See gen11_reset_one_iir() for more info.
v2: else if !!! (Paulo)
v3: another else if (Vinay)
v4:
- Rebased
- Renamed patch
- Improved the ordering of GENs
- Improved the printing of per-GEN info
v5: Avoid maybe-unitialized & add comment explaining the lack
of PM ISR & IIR
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
[Paulo: fix commit message and coding style.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525989595-18220-1-git-send-email-oscar.mateo@intel.com
We have some very odd semantics for reading the command line through
/proc, because we allow people to rewrite their own command line pretty
much at will, and things get positively funky when you extend your
command line past the point that used to be the end of the command line,
and is now in the environment variable area.
But our weird semantics doesn't mean that we should write weird and
complex code to handle them.
So re-write get_mm_cmdline() to be much simpler, and much more explicit
about what it is actually doing and why. And avoid the extra check for
"is there a NUL character at the end of the command line where I expect
one to be", by simply making the NUL character handling be part of the
normal "once you hit the end of the command line, stop at the first NUL
character" logic.
It's quite possible that we should stop the crazy "walk into
environment" entirely, but happily it's not really the usual case.
NOTE! We tried to really simplify and limit our odd cmdline parsing some
time ago, but people complained. See commit c2c0bb4462 ("proc: fix
PAGE_SIZE limit of /proc/$PID/cmdline") for details about why we have
this complexity.
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the sockmap design BPF programs (SK_SKB_STREAM_PARSER,
SK_SKB_STREAM_VERDICT and SK_MSG_VERDICT) are attached to the sockmap
map type and when a sock is added to the map the programs are used by
the socket. However, sockmap updates from both userspace and BPF
programs can happen concurrently with the attach and detach of these
programs.
To resolve this we use the bpf_prog_inc_not_zero and a READ_ONCE()
primitive to ensure the program pointer is not refeched and
possibly NULL'd before the refcnt increment. This happens inside
a RCU critical section so although the pointer reference in the map
object may be NULL (by a concurrent detach operation) the reference
from READ_ONCE will not be free'd until after grace period. This
ensures the object returned by READ_ONCE() is valid through the
RCU criticl section and safe to use as long as we "know" it may
be free'd shortly.
Daniel spotted a case in the sock update API where instead of using
the READ_ONCE() program reference we used the pointer from the
original map, stab->bpf_{verdict|parse|txmsg}. The problem with this
is the logic checks the object returned from the READ_ONCE() is not
NULL and then tries to reference the object again but using the
above map pointer, which may have already been NULL'd by a parallel
detach operation. If this happened bpf_porg_inc_not_zero could
dereference a NULL pointer.
Fix this by using variable returned by READ_ONCE() that is checked
for NULL.
Fixes: 2f857d0460 ("bpf: sockmap, remove STRPARSER map_flags and add multi-map support")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If the user were to only attach one of the parse or verdict programs
then it is possible a subsequent sockmap update could incorrectly
decrement the refcnt on the program. This happens because in the
rollback logic, after an error, we have to decrement the program
reference count when its been incremented. However, we only increment
the program reference count if the user has both a verdict and a
parse program. The reason for this is because, at least at the
moment, both are required for any one to be meaningful. The problem
fixed here is in the rollback path we decrement the program refcnt
even if only one existing. But we never incremented the refcnt in
the first place creating an imbalance.
This patch fixes the error path to handle this case.
Fixes: 2f857d0460 ("bpf: sockmap, remove STRPARSER map_flags and add multi-map support")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename error recovery interfaces with "pcie_" prefix so they can be made
non-static.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: move declaration to later patch, leave functions static]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
PCIe ERR_FATAL errors mean the Link is unreliable. Components on the Link
may need to be reset to return to reliable operation (PCIe r4.0, sec
6.2.2). We previously handled these errors much differently depending on
whether the platform supports Downstream Port Containment (DPC) (PCIe r4.0,
sec 6.2.10) or not.
The AER driver has historically logged the error details, called
driver-supplied pci_error_handlers callbacks, and reset the Link. This
reset downstream devices, but did not remove them from the PCI subsystem,
re-enumerate them, or call their driver .remove() or .probe() methods.
DPC is different because the hardware automatically disables the Link when
it detects ERR_FATAL, which resets downstream devices. There's no
opportunity for pci_error_handlers callbacks before resetting the Link.
The DPC driver removes affected devices (which calls their driver .remove()
methods), brings the Link back up, and re-enumerates (which calls driver
.probe() methods).
Align AER ERR_FATAL handling with DPC by resetting the Link in software,
skipping the driver pci_error_handlers callbacks, removing the devices from
the PCI subsystem, and re-enumerating. The idea is that drivers and
devices should see the same behavior for ERR_FATAL events, regardless of
whether they're handled by AER or DPC.
Here are the basic ERR_FATAL recovery steps, showing the previous AER
behavior, the AER behavior after this patch, and the DPC behavior:
AER AER DPC
previous new behavior
-------- --- --------
Log error yes yes yes (minimal)
drv.error_detected() yes no no
Reset Link yes yes yes
drv.mmio_enabled() yes no no
drv.slot_reset() yes no no
drv.resume() yes no no
Remove PCI devices no yes yes
(calls drv.remove())
Re-enumerate no yes yes
(calls drv.probe())
N.B. With DPC, the Link reset happens before the driver .remove() calls,
while with AER, the reset happens *after* the .remove() calls. The goal is
to eventually do the reset before .remove() for AER as well.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, squash doc patch into this, remove unused
"result_data"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Clients such as hotplug and Downstream Port Containment (DPC) both need to
wait until a link becomes active or inactive.
Add a generic pcie_wait_link_active() interface and use it instead of
duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
This is used to support suspend modes like RTC-only and hibernate where
the state of the registers controlling clockdomains is lost.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set a specific source e-switch when setting a rule that matches on the
ingress port.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.
The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set a specific destination e-switch when setting a destination vport.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When creating FTE, properly distinguish between destination being vport
or tir. The previous code just worked accidentally b/c of both dest being
in the same offset within a union.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
Under merged eswitch, both the matching on source vport and setting
destination vport can have a 2nd attribute which is the vhca id of the
eswitch owner.
For example:
esw0: {match: <src vport=1 owner=0> action: fwd to <dst vport=7, owner=1>}
is a flow set on eswitch0 matching on source vport=1 from his eswitch
and the action being fwd to dest vport=7 of eswitch1.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz Klein <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Florian Fainelli says:
====================
net: Allow more drivers with COMPILE_TEST
This patch series includes more drivers to be build tested with COMPILE_TEST
enabled. This helps cover some of the issues I just ran into with missing
a driver *sigh*.
Chanves in v3:
- drop the TI Keystone NETCP driver from the COMPILE_TEST additions
Changes in v2:
- allow FEC to build outside of CONFIG_ARM/ARM64 by defining a layout of
registers, this is not meant to run, so this is not a real issue if we
are not matching the correct register layout
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Those drivers build just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Freescale FEC driver builds fine with COMPILE_TEST, so make that
possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the TI drivers build just fine with COMPILE_TEST, cpmac (AR7) is
the exception because it uses a header file from
arch/mips/include/asm/mach-ar7/ar7.h and keystone netcp which requires
help from drivers/soc/ti/ for queue management helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add informative messages for error paths related to adding a
VLAN to a device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.
This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.
Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32
HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.59 0.00 32.93 0.00 0.00 43.07 0.00 0.00 23.42
HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.70 0.00 31.70 0.00 0.00 25.68 0.00 0.00 41.92
HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.86 0.00 24.14 0.00 0.00 6.59 0.00 0.00 68.41
HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.87 0.00 23.75 0.00 0.00 6.19 0.00 0.00 69.19
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device features may change during transmission. In particular with
corking, a device may toggle scatter-gather in between allocating
and writing to an skb.
Do not unconditionally assume that !NETIF_F_SG at write time implies
that the same held at alloc time and thus the skb has sufficient
tailroom.
This issue predates git history.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-05-17
This series contains updates to ixgbe, ixgbevf and ice drivers.
Cathy Zhou resolves sparse warnings by using the force attribute.
Mauro S M Rodrigues fixes a bug where IRQs were not freed if a PCI error
recovery system opts to remove the device which causes
ixgbe_io_error_detected() to return PCI_ERS_RESULT_DISCONNECT before
calling ixgbe_close_suspend() which results in IRQs not freed and
crashing when the remove handler calls pci_disable_device(). Resolved
this by calling ixgbe_close_suspend() before evaluating the PCI channel
state.
Pavel Tatashin releases the rtnl_lock during the call to
ixgbe_close_suspend() to allow scaling if device_shutdown() is
multi-threaded.
Emil modifies ixgbe to not validate the MAC address during a reset,
unless the MAC was set on the host so that the VF will get a new MAC
address every time it reloads. Also updates ixgbevf to set
hw->mac.perm_addr in order to retain the custom MAC on a reset.
Anirudh updates the ice NVM read/erase/update AQ commands to align with
the latest specification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in ls1x_rtc_probe used to release resources but since
it is using devm functions, it only returns a value. Make the code clearer
by returning directly instead of using goto.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Let the core handle offsetting and windowing the RTC range.
The RTC has a 40-bit counter counting at 1024 Hz. So its maximum value is
2^(40-10) - 1. Also, let the core handle the offset instead of coding it in
the callbacks. Keep the default epoch at the beginning of 2009 (this will
fail in 2043).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after the RTC is registered
because the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The vr41xx RTC is a 48-bit counter counting at 32.768 kHz, giving a maximum
value of 2^(48-15)-1 seconds.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The probe function is not allowed to fail after the RTC is registered
because the following may happen:
CPU0: CPU1:
sys_load_module()
do_init_module()
do_one_initcall()
cmos_do_probe()
rtc_device_register()
__register_chrdev()
cdev->owner = struct module*
open("/dev/rtc0")
rtc_device_unregister()
module_put()
free_module()
module_free(mod->module_core)
/* struct module *module is now
freed */
chrdev_open()
spin_lock(cdev_lock)
cdev_get()
try_module_get()
module_is_live()
/* dereferences already
freed struct module* */
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Petr Machata says:
====================
net: ip6_gre: Fixes in headroom handling
This series mends some problems in headroom management in ip6_gre
module. The current code base has the following three closely-related
problems:
- ip6gretap tunnels neglect to ensure there's enough writable headroom
before pushing GRE headers.
- ip6erspan does this, but assumes that dev->needed_headroom is primed.
But that doesn't happen until ip6_tnl_xmit() is called later. Thus for
the first packet, ip6erspan actually behaves like ip6gretap above.
- ip6erspan shares some of the code with ip6gretap, including
calculations of needed header length. While there is custom
ERSPAN-specific code for calculating the headroom, the computed
values are overwritten by the ip6gretap code.
The first two issues lead to a kernel panic in situations where a packet
is mirrored from a veth device to the device in question. They are
fixed, respectively, in patches #1 and #2, which include the full panic
trace and a reproducer.
The rest of the patchset deals with the last issue. In patches #3 to #6,
several functions are split up into reusable parts. Finally in patch #7
these blocks are used to compose ERSPAN-specific callbacks where
necessary to fix the hlen calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though ip6erspan_tap_init() sets up hlen and tun_hlen according to
what ERSPAN needs, it goes ahead to call ip6gre_tnl_link_config() which
overwrites these settings with GRE-specific ones.
Similarly for changelink callbacks, which are handled by
ip6gre_changelink() calls ip6gre_tnl_change() calls
ip6gre_tnl_link_config() as well.
The difference ends up being 12 vs. 20 bytes, and this is generally not
a problem, because a 12-byte request likely ends up allocating more and
the extra 8 bytes are thus available. However correct it is not.
So replace the newlink and changelink callbacks with an ERSPAN-specific
ones, reusing the newly-introduced _common() functions.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from ip6gre_changelink() a reusable function
ip6gre_changelink_common(). This will allow introduction of
ERSPAN-specific _changelink() function with not a lot of code
duplication.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from ip6gre_newlink() a reusable function
ip6gre_newlink_common(). The ip6gre_tnl_link_config() call needs to be
made customizable for ERSPAN, thus reorder it with calls to
ip6_tnl_change_mtu() and dev_hold(), and extract the whole tail to the
caller, ip6gre_newlink(). Thus enable an ERSPAN-specific _newlink()
function without a lot of duplicity.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split a reusable function ip6gre_tnl_copy_tnl_parm() from
ip6gre_tnl_change(). This will allow ERSPAN-specific code to
reuse the common parts while customizing the behavior for ERSPAN.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip6gre_tnl_link_config() is used for setting up
configuration of both ip6gretap and ip6erspan tunnels. Split the
function into the common part and the route-lookup part. The latter then
takes the calculated header length as an argument. This split will allow
the patches down the line to sneak in a custom header length computation
for the ERSPAN tunnel.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`e' is being freed twice.
Fix this by removing one of the kfree() calls.
Addresses-Coverity-ID: 1468983 ("Double free")
Fixes: 8111038444 ("bpf: sockmap, add hash map support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There is a potential execution path in which variable err is
returned without being properly initialized previously.
Fix this by initializing variable err to 0.
Addresses-Coverity-ID: 1468964 ("Uninitialized scalar variable")
Fixes: e5cd3abcb3 ("bpf: sockmap, refactor sockmap routines to work with hashmap")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>