Instead of hand-managing the sysctl set and restore, use the wrappers
sysctl_set() and sysctl_restore() to do the bookkeeping automatically.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two helper functions: sysctl_set() to change the value of a given
sysctl setting, and sysctl_restore() to change it back to what it was.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From 4.18 kernel, all the MMC controller instances in DRA7
are programmed using sdhci based driver (sdhci-omap.c). Document
this new requirement here. Both omap2plus_defconfig and
multi_v7_defconfig has CONFIG_MMC_SDHCI_OMAP enabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the supported UHS mode can be obtained from CAPA2
register, SD Host Controller Standard Specification
doesn't define bits for MMC's HS200 and DDR mode capability.
Add properties to indicate MMC HS200 and DDR speed mode capability in
dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for WLAN using wilink8 module. On dra76-evm, MMC4 is
used for connecting to wilink8 module.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wilink module is a combo wireless connectivity sdio
card based on Texas Instrument's wl18xx solution. It is a
4-wire, 1.8V, embedded sdio wlan device with an external
irq line and is power-controlled by a gpio-based fixed
regulator.
Add pinmux configuration and IODelay values for MMC4.
On dra7-evm, MMC4 is used for connecting to wilink module.
IODelay data credits to : Vishal Mahaveer <vishalm@ti.com>
and Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On TI's DRA74x EVM, EVM_3V6 is connected is connected to the VBAT line
of the wilink card. Model it here so that it can be used while adding
wilink8 WLAN support.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wilink8 module is a combo wireless connectivity card based
on Texas Instrument's wl18xx solution.
Add support for the wlan capabilities of this module by muxing
the relevant mmc lines, and setting the required device-tree
data.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
[nsekhar@ti.com: drop WLAN_EN pinmux. It should be done by bootloader.
Also, some commit message adjustments]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IO lines of MMC2 in am57xx-beagle-x15/am57xx-idk is connected to
3.3v. Use "ddr_3_3v" instead of "ddr_1_8v" to indicate DDR mode
works in 3.3v on these boards.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra76x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for am574x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am574x-idk.dts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 0e43884cca ("ARM: dts: dra71-evm: Select pull
down for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in dra71-evm.dts to change the CLK line to
PIN_INPUT_PULLDOWN. However instead of changing the pinctrl group,
use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line
without external pull up.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 18aa0f4bca ("ARM: dts: am57xx-idk: Select pull down
for mmc1_clk line in default mode") modified mmc1_pins_default
pinctrl group in am57xx-idk-common.dtsi in order to change the CLK
line to PIN_INPUT_PULLDOWN. However instead of modifying the pinctrl
group, use the new pinctrl group "mmc1_pins_default_no_clk_pu" in
dra7-mmc-iodelay.dtsi added specifically to be used for CLK line without
external pull up.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
Add a new pinctrl group for clock line without pullup to be used in boards
where mmc1_clk line is not connected to an external pullup.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc specific pinmux is selected from dra72x-mmc-iodelay.dtsi, so remove
it from dra72-evm-common.dtsi.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some non-compliant high-speed USB devices have bulk endpoints with a
1024-byte maxpacket size. Although such endpoints don't work with
xHCI host controllers, they do work with EHCI controllers. We used to
accept these invalid sizes (with a warning), but we no longer do
because of an unintentional change introduced by commit aed9d65ac3
("USB: validate wMaxPacketValue entries in endpoint descriptors").
This patch restores the old behavior, so that people with these
peculiar devices can use them without patching their kernels by hand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Elvinas <elvinas@veikia.lt>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The missing "compatible" entries are needed by drivers/clk/ti/clkctrl.c,
and without them the structures initialized in drivers/clk/ti/clk-814x.c
are not passed to configuration code. The result is a "not found from
clkctrl data" error message, although boot proceeds anyway.
The reason why the compatible is not found is because the board specific
files override the SoC compatible without including it. This did not
cause any issues until with the clkctrl nodes got introduced.
Very lightly tested on a (lurching) AM3874 design that's in the middle
of a kernel upgrade from TI's abandoned 2.6.37 tree.
Also tested on j5eco-evm and hp-t410 to verify the clkctrl clocks are
found.
Fixes: bb30465b59 ("ARM: dts: dm814x: add clkctrl nodes")
Fixes: 80a06c0d83 ("ARM: dts: dm816x: add clkctrl nodes")
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony: updated to fix for 8168-evm, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The deferred_fiq handler used to limit hardware operations to IRQ
unmask only, relying on gpio-omap assigned handler performing the ACKs.
Since commit 80ac93c274 ("gpio: omap: Fix lost edge interrupts") this
is no longer the case as handle_edge_irq() has been replaced with
handle_simmple_irq() which doesn't touch the hardware.
Add single ACK operation per each active IRQ pin to the handler. While
being at it, move unmask operation out of irq_counter loop so it is
also called only once for each active IRQ pin.
Fixes: 80ac93c274 ("gpio: omap: Fix lost edge interrupts")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These definitions are hex, and the old value (decimal 40) doesn't make
sense in the context. I do not have a T410 and cannot test if this makes
any practical difference.
Fixes: f24f1bdc02 ("ARM: dts: Enable emmc on hp t410")
signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Trivial fix to spelling mistake in netdev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
selftests: forwarding: Two enhancements
First patch increases the maximum deviation in the multipath tests which
proved to be too low in some cases.
Second patch allows user to run only specific tests from each file using
the TESTS environment variable. This granularity is needed in setups
where not all the tests can pass.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit a511858c75 ("selftests: fib_tests: Allow user to run
a specific test"), allow user to run only a subset of the tests using
the TESTS environment variable.
This is useful when not all the tests can pass on a given system.
Example:
# export TESTS="ping_ipv4 ping_ipv6"
# ./bridge_vlan_aware.sh
TEST: ping [PASS]
TEST: ping6 [PASS]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We sometimes observe failures in the test due to too large discrepancy
between the measured and expected ratios. For example:
TEST: ECMP [FAIL]
Too large discrepancy between expected and measured ratios
INFO: Expected ratio 1.00 Measured ratio 1.11
Fix this by allowing an up to 15% deviation between both ratios.
Another possibility is to increase the number of generated flows, but
this will prolong the execution time of the test, which is already quite
high.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.19.1.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel should not calculate new hmacs for mounts done by
non-root users. Update evm_calc_hmac_or_hash() to refuse to
calculate new hmacs for mounts for non-init user namespaces.
Cc: linux-integrity@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: James Morris <james.l.morris@oracle.com>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Dongsu Park <dongsu@kinvolk.io>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
-----BEGIN PGP SIGNATURE-----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=jdZ7
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.17-4' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
"Fix an incorrect warning selection introduced in the last merge
window"
* tag 'dma-mapping-4.17-4' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix inversed DMA_ATTR_NO_WARN test
This is not needed since commit fcbb1e02ee ("drivers: thermal:
Remove ARCH_HAS_BANDGAP dependency for samsung") from 2014.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The JIT compiler emits ia32 bit instructions. Currently, It supports eBPF
only. Classic BPF is supported because of the conversion by BPF core.
Almost all instructions from eBPF ISA supported except the following:
BPF_ALU64 | BPF_DIV | BPF_K
BPF_ALU64 | BPF_DIV | BPF_X
BPF_ALU64 | BPF_MOD | BPF_K
BPF_ALU64 | BPF_MOD | BPF_X
BPF_STX | BPF_XADD | BPF_W
BPF_STX | BPF_XADD | BPF_DW
It doesn't support BPF_JMP|BPF_CALL with BPF_PSEUDO_CALL at the moment.
IA32 has few general purpose registers, EAX|EDX|ECX|EBX|ESI|EDI. I use
EAX|EDX|ECX|EBX as temporary registers to simulate instructions in eBPF
ISA, and allocate ESI|EDI to BPF_REG_AX for constant blinding, all others
eBPF registers, R0-R10, are simulated through scratch space on stack.
The reasons behind the hardware registers allocation policy are:
1:MUL need EAX:EDX, shift operation need ECX, so they aren't fit
for general eBPF 64bit register simulation.
2:We need at least 4 registers to simulate most eBPF ISA operations
on registers operands instead of on register&memory operands.
3:We need to put BPF_REG_AX on hardware registers, or constant blinding
will degrade jit performance heavily.
Tested on PC (Intel(R) Core(TM) i5-5200U CPU).
Testing results on i5-5200U:
1) test_bpf: Summary: 349 PASSED, 0 FAILED, [319/341 JIT'ed]
2) test_progs: Summary: 83 PASSED, 0 FAILED.
3) test_lpm: OK
4) test_lru_map: OK
5) test_verifier: Summary: 828 PASSED, 0 FAILED.
Above tests are all done in following two conditions separately:
1:bpf_jit_enable=1 and bpf_jit_harden=0
2:bpf_jit_enable=1 and bpf_jit_harden=2
Below are some numbers for this jit implementation:
Note:
I run test_progs in kselftest 100 times continuously for every condition,
the numbers are in format: total/times=avg.
The numbers that test_bpf reports show almost the same relation.
a:jit_enable=0 and jit_harden=0 b:jit_enable=1 and jit_harden=0
test_pkt_access:PASS:ipv4:15622/100=156 test_pkt_access:PASS:ipv4:10674/100=106
test_pkt_access:PASS:ipv6:9130/100=91 test_pkt_access:PASS:ipv6:4855/100=48
test_xdp:PASS:ipv4:240198/100=2401 test_xdp:PASS:ipv4:138912/100=1389
test_xdp:PASS:ipv6:137326/100=1373 test_xdp:PASS:ipv6:68542/100=685
test_l4lb:PASS:ipv4:61100/100=611 test_l4lb:PASS:ipv4:37302/100=373
test_l4lb:PASS:ipv6:101000/100=1010 test_l4lb:PASS:ipv6:55030/100=550
c:jit_enable=1 and jit_harden=2
test_pkt_access:PASS:ipv4:10558/100=105
test_pkt_access:PASS:ipv6:5092/100=50
test_xdp:PASS:ipv4:131902/100=1319
test_xdp:PASS:ipv6:77932/100=779
test_l4lb:PASS:ipv4:38924/100=389
test_l4lb:PASS:ipv6:57520/100=575
The numbers show we get 30%~50% improvement.
See Documentation/networking/filter.txt for more information.
Changelog:
Changes v5-v6:
1:Add do {} while (0) to RETPOLINE_RAX_BPF_JIT for
consistence reason.
2:Clean up non-standard comments, reported by Daniel Borkmann.
3:Fix a memory leak issue, repoted by Daniel Borkmann.
Changes v4-v5:
1:Delete is_on_stack, BPF_REG_AX is the only one
on real hardware registers, so just check with
it.
2:Apply commit 1612a981b7 ("bpf, x64: fix JIT emission
for dead code"), suggested by Daniel Borkmann.
Changes v3-v4:
1:Fix changelog in commit.
I install llvm-6.0, then test_progs willn't report errors.
I submit another patch:
"bpf: fix misaligned access for BPF_PROG_TYPE_PERF_EVENT program type on x86_32 platform"
to fix another problem, after that patch, test_verifier willn't report errors too.
2:Fix clear r0[1] twice unnecessarily in *BPF_IND|BPF_ABS* simulation.
Changes v2-v3:
1:Move BPF_REG_AX to real hardware registers for performance reason.
3:Using bpf_load_pointer instead of bpf_jit32.S, suggested by Daniel Borkmann.
4:Delete partial codes in 1c2a088a66, suggested by Daniel Borkmann.
5:Some bug fixes and comments improvement.
Changes v1-v2:
1:Fix bug in emit_ia32_neg64.
2:Fix bug in emit_ia32_arsh_r64.
3:Delete filename in top level comment, suggested by Thomas Gleixner.
4:Delete unnecessary boiler plate text, suggested by Thomas Gleixner.
5:Rewrite some words in changelog.
6:CodingSytle improvement and a little more comments.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It looks weird that the stack_trace_filter file can be written by root
but shows that it does not have write permission by ll command.
Link: http://lkml.kernel.org/r/1518054113-28096-1-git-send-email-liuzhengyuan@kylinos.cn
Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e
where xhci_free_virt_device() sets slot id to 0 if udev exists:
if (dev->udev && dev->udev->slot_id)
dev->udev->slot_id = 0;
dev->udev will be true even if udev is freed because dev->udev is
not set to NULL.
set dev->udev pointer to NULL in xhci_free_dev()
The original patch went to stable so this fix needs to be applied
there as well.
Fixes: a400efe455 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The set_graph_function and set_graph_notrace file mode should be 0644
instead of 0444 as they are writeable. Note, the mode appears to be ignored
regardless, but they should at least look sane.
Link: http://lkml.kernel.org/r/1409725869-4501-1-git-send-email-linx.z.chen@intel.com
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Chen LinX <linx.z.chen@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
After commit bb06ec3145 ("nvme: expand nvmf_check_if_ready checks")
resetting of the loopback nvme target failed as we forgot to switch
it's state to NVME_CTRL_CONNECTING before we reconnect the admin
queues. Therefore the checks in nvmf_check_if_ready() choose to go to
the reject_io case and thus we couldn't sent out an identify
controller command to reconnect.
Change the controller state to NVME_CTRL_CONNECTING after tearing down
the old connection and before re-establishing the connection.
Fixes: bb06ec3145 ("nvme: expand nvmf_check_if_ready checks")
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When CONFIG_NVME_MULTIPATH is set, but we're not using nvme to multipath,
namespaces with multiple paths were not creating unique names due to
reusing the same instance number from the namespace's head.
This patch fixes this by falling back to the non-multipath naming method
when the parameter disabled using multipath.
Reported-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can't allow the user to change multipath settings at runtime, as this
will create naming conflicts due to the different naming schemes used
for each mode.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the command a separate metadata buffer attached, the request needs
to have the integrity flag set so the driver knows to map it.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When specifying same string type option several times,
current option parsing may cause memory leak. Hence,
call kfree for previous one in this case.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
syzbot is reporting use after free bug in debugfs_remove() [1].
This is because fault injection made memory allocation for
debugfs_create_file() from bdi_debug_register() from bdi_register_va()
fail and continued with setting WB_registered. But when debugfs_remove()
is called from debugfs_remove(bdi->debug_dir) from bdi_debug_unregister()
from bdi_unregister() from release_bdi() because WB_registered was set
by bdi_register_va(), IS_ERR_OR_NULL(bdi->debug_dir) == false despite
debugfs_remove(bdi->debug_dir) was already called from bdi_register_va().
Fix this by making IS_ERR_OR_NULL(bdi->debug_dir) == true.
[1] https://syzkaller.appspot.com/bug?id=5ab4efd91a96dcea9b68104f159adf4af2a6dfc1
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+049cb4ae097049dac137@syzkaller.appspotmail.com>
Fixes: 97f0769793 ("bdi: convert bdi_debug_register to int")
Cc: weiping zhang <zhangweiping@didichuxing.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function name is wrong in ip6gre_tnl_addr_conflict() comment, which
use ip6_tnl_addr_conflict instead of ip6gre_tnl_addr_conflict.
Signed-off-by: Sun Lianwen <sunlw.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot is reporting hung tasks at wait_on_bit(WB_shutting_down) in
wb_shutdown() [1]. This seems to be because commit 5318ce7d46 ("bdi:
Shutdown writeback on all cgwbs in cgwb_bdi_destroy()") forgot to call
wake_up_bit(WB_shutting_down) after clear_bit(WB_shutting_down).
Introduce a helper function clear_and_wake_up_bit() and use it, in order
to avoid similar errors in future.
[1] https://syzkaller.appspot.com/bug?id=b297474817af98d5796bc544e1bb806fc3da0e5e
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+c0cf869505e03bdf1a24@syzkaller.appspotmail.com>
Fixes: 5318ce7d46 ("bdi: Shutdown writeback on all cgwbs in cgwb_bdi_destroy()")
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The USB_DEVICE_INTERFACE_NUMBER matching macro assumes that
the { vendorid, productid, interfacenumber } set uniquely
identifies one specific function. This has proven to fail
for some configurable devices. One example is the Quectel
EM06/EP06 where the same interface number can be either
QMI or MBIM, without the device ID changing either.
Fix by requiring the vendor-specific class for interface number
based matching. Functions of other classes can and should use
class based matching instead.
Fixes: 03304bcb5e ("net: qmi_wwan: use fixed interface number matching")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Dillabaugh says:
====================
Update csum tc action for batch operation.
This patchset includes two patches the first updating act_csum.c
to include the get_fill_size routine required for batch operation, and
the second including updated TDC tests for the feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During state readout we first read out the pipe src size, store
that information in the user mode h/vdisplay, but later on we overwrite
that with the actual crtc timings. That makes our read out crtc state
inconsistent with itself when the BIOS has enabled the panel fitter to
scale the pipe contents. Let's preserve the pipe src size based
information in the user mode to make things consistent again.
This fixes a problem introduced by commit a2936e3d9a ("drm/i915:
Use drm_mode_get_hv_timing() to populate plane clip rectangle")
where the inconsistent state is now leading the plane clipping code
to report a failure on account the plane dst coordinates not matching
the user mode size. Previously we did the plane clipping based on
the pipe src size instead and thus never noticed the inconsistency.
The failure manifests as a WARN:
[ 0.762117] [drm:intel_dump_pipe_config [i915]] requested mode:
[ 0.762142] [drm:drm_mode_debug_printmodeline [drm]] Modeline 0:"1366x768" 60 72143 1366 1414 1446 1526 768 771 777 784 0x40 0xa
...
[ 0.762327] [drm:intel_dump_pipe_config [i915]] port clock: 72143, pipe src size: 1024x768, pixel rate 72143
...
[ 0.764666] [drm:drm_atomic_helper_check_plane_state [drm_kms_helper]] Plane must cover entire CRTC
[ 0.764690] [drm:drm_rect_debug_print [drm]] dst: 1024x768+0+0
[ 0.764711] [drm:drm_rect_debug_print [drm]] clip: 1366x768+0+0
[ 0.764713] ------------[ cut here ]------------
[ 0.764714] Could not determine valid watermarks for inherited state
[ 0.764792] WARNING: CPU: 4 PID: 159 at drivers/gpu/drm/i915/intel_display.c:14584 intel_modeset_init+0x3ce/0x19d0 [i915]
...
Cc: FadeMind <fademind@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: FadeMind <fademind@gmail.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Tested-by: Dave Jones <davej@codemonkey.org.uk>
References: https://lists.freedesktop.org/archives/intel-gfx/2018-April/163186.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105992
Fixes: a2936e3d9a ("drm/i915: Use drm_mode_get_hv_timing() to populate plane clip rectangle")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426163015.14232-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: FadeMind <fademind@gmail.com>
No functional changes, just a minor knit. Stumbled across the kernel doc for
schedule_timeout() which quotes "In all cases the return value is guaranteed
to be non-negative". Also, the return code of schedule_timeout() already checks
for negative values "return timeout < 0 ? 0 : timeout;" and returns 0
in such cases. Furthermore, the msec_to_jiffies returns an ungined long
value. So, let's do away with the redundant check for an atomic
pipe update.
v2: Commit message changes (Manasi).
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502233300.81220-1-tarun.vyas@intel.com
We get a build error when compiling the iommu driver without CONFIG_OF:
drivers/iommu/rockchip-iommu.c: In function 'rk_iommu_of_xlate':
drivers/iommu/rockchip-iommu.c:1101:2: error: implicit declaration of function 'of_dev_put'; did you mean 'of_node_put'? [-Werror=implicit-function-declaration]
This replaces the of_dev_put() with the equivalent
platform_device_put().
Fixes: 5fd577c3ea ("iommu/rockchip: Use OF_IOMMU to attach devices automatically")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It is possible that multiple I/O requests hits on failed cache device or
backing device, therefore it is quite common that CACHE_SET_IO_DISABLE is
set already when a task tries to set the bit from bch_cache_set_error().
Currently the message "CACHE_SET_IO_DISABLE already set" is printed by
pr_warn(), which might mislead users to think a serious fault happens in
source code.
This patch uses pr_info() to print the information in such situation,
avoid extra worries. This information is helpful to understand bcache
behavior in cache device failures, so I still keep them in source code.
Fixes: 771f393e8f ("bcache: add CACHE_SET_IO_DISABLE to struct cache_set flags")
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>